Thesis (Ph.D.) - University of St Andrews, June 2009. / Restricted until 1st June 2010.

Thesis (Ph. D.)--University of Washington, 2006. / Vita. Includes bibliographical references (leaves 256-264).

This thesis is dedicated to developing conjugated polymer and small-molecule donor materials for solution-processable organic solar cells. To begin with, a brief introduction of organic solar cells (OSCs) and an overview of donor materials development were presented in Chapter 1. In chapter 2, we used carbon-carbon triple bands as linkage of the TVT unit to develop a new building block, ATVTA. Small molecules S-03, S-04, and S-05 with ATVTA as building block showed broad absorption spectra and low-lying HOMO energy levels. S-01 with TVT unit and S-02 with AT2 as building block were also synthesized for clear comparison. OSCs devices based on S-01 and S-02 showed a Voc of 0.88 V and 0.89 V, respectively. The device based on S-03 exhibited a high Voc of 0.96 V, leading to a PCE of 2.19%. The devices based on S-04 and S-05 afforded a notable Voc over 1.0 V. The results demonstrate that ATVTA unit is a promising building block for extending π conjugation of the molecules without pulling up their HOMO energy levels. Chapter 3 focused on the development of 2D-conjugated small-molecule donor materials. The 2D-conjugated small molecule S-06 possesses excellent solution processability, broad absorption feature, respectable hole mobility and good film-forming morphology. The conjugated thiophene side chain not only effectively extends the absorption spectrum, but also lowers the HOMO energy level, which is desirable for obtaining high Voc. The BHJ OSCs based on S-06:PC70BM (1:0.5, w/w) afforded a high PCE of 4.0% and a notable FF of 0.63 without any special treatment needed. This preliminary work demonstrates that this kind of 2D-conjugated small molecules offer a good strategy to design new photovoltaic small molecule-based donor materials with high FF and Voc for high-efficiency OSCs. The consistently developed two 2D-conjugated small molecules S-07 and S-08 also possess low-lying HOMO energy levels. OSC device based on S-07:PC60BM (1:3, w/w) afforded a notable Voc of 0.96 V, with a PCE of 2.52%. BHJ devices based on S-08 will be fabricated and tested to investigate its photovoltaic properties in the near future. We developed a series of oligothiophenes with platinum(Ⅱ) as the building block in Chapter 4. These small metallated conjugated small molecules exhibited broad spectra and relatively low-lying HOMO energy levels in the range of –5.27 eV to –5.40 eV. Introducing platinum(Ⅱ) arylene ethynylenes as building block can be considered as an approach to obtain small-molecule donors with satisfactory absorption features and HOMO energy levels. Nevertheless, due to the low FF, the PCEs of these donor materials based devices are lower than 2%. Fine tuning the film morphologies of this kind of metallated small-molecule donor materials should be carried out to improve their photovoltaic performance. We addressed an efficient approach to improve the photovoltaic properties by side chain engineering in 2D-conjugated polymers in Chapter 5. Considering the fact that the Voc of PBDTTT based devices is less than 0.8 V, we introduced alkylthio substituent on the conjugated thiophene side chains of the 2D-conjugated copolymer to further improve the photovoltaic performance of the 2D-conjugated copolymers PBDTTTs. The weak electron-donating ability of the alkylthio side chains effectively down-shifted the HOMO energy level of PBDTT-S-TT by 0.11 eV in comparison to the corresponding polymer with alkyl substitution on the conjugated thiophene side chains. The PSC device based on PBDTT-S-TT showed an enhanced Voc of 0.84 V, which is among the highest one in the reported copolymers based on BDT and TT units, leading to an enhanced PCE of 8.42%. The results indicate that molecular modification by introducing alkylthio side chain will be a promising strategy to broaden the absorption, down-shift the HOMO energy level and increase the hole mobility of the low band gap 2D-conjugated polymers for further enhancing the photovoltaic performance of PSCs. PBDTT-O-TT-C and PBDTT-S-TT-C were developed to further study the conclusion. We found that OSC device based on PBDTT-S-TT-C with alkylthio side chain also demonstrated a high Voc of 0.89 V, with a PCE of 6.85% when processed with 3% DIO additive

This dissertation is a study of two major topics that involve synthetic strategies for new classes of phosphorescent gold(I)-based metallodendrimers. The phosphorescence of organic and inorganic luminophores originates from spin-orbit coupling owing to internal or external heavy atom effects as well as metal-centered emissions. Previous work in the Omary group entailed systematically designed small molecules, metallopolymers, and unconjugated metallodendrimers that contain d10 and d8 metals, whereas this dissertation aims in part to expand such strategies to the conjugated metallodendrimer regime. In one approach novel synthetic strategies were used to make first-generation phenyl acetylene dendrimers and phosphine derivatives thereof. The phosphine dendrimers are made by tethering one of the phosphines to an unsaturated dendrimer, as such phosphine dendrimers are better chromophores and luminophores due to their structural rigidity and extended conjugation. In another approach, 2- and 3-coordinate Au(I) dendritic complexes are synthesized from these phosphine dendrimers. This study is further extended to study metallodendritic complexes with different cores, for example triphenylene-based metallodendritic complexes with six acetylene branches. The physical properties of the metallodendrimers can be modulated upon proceeding to further dendrimer generations or by using solubilizing groups on the peripheral phosphines, thus allowing better processability for thin-film fabrication as required for molecular electronic devices and higher chance for crystal growth toward accurate structural characterization. Other data produced in this project suggested that some structural alterations led to porous solids that render them suitable for realized and potential applications in energy storage and carbon capture. The interesting luminescence properties of the metallodendrimers and porous extended solids produced in this dissertation are significant toward utilizing such materials for optoelectronic applications such as energy-saving organic light-emitting diodes and optical sensors for environmental pollutants.

Conjugated polymers and related molecular materials comprise a field of materials chemistry focused on the development of semiconducting organic plastics that find use in applications such as organic solar cells and organic light-emitting diodes. The optical and electronic properties of these molecules, such as absorption and emission of light, can be tuned through engineering at the molecular level. However, many of the current molecules of choice suffer from high-lying frontier orbitals, which results in a mismatch of energy levels to common components of electronic devices along with potential oxidative instability, constraining device performance in real environments. To rectify these issues, the electron-deficient thiazole heterocycle has been incorporated into fused-ring conjugated motifs of both organic and inorganic nature. The new thiazole materials all exhibited the expected stabilization of their frontier orbitals compared to the thiophene analogues. The absorption profiles of the thiazole materials are similar to the thiophene analogues, but with reduced molar absorptivity as a general trend, potentially limiting the efficiency of thiazole derived materials as components of photovoltaic devices. Through experimentation and development of multiple new classes of organic and inorganic thiazole materials, it was found that a larger proportion of thiazole content correlates to a larger decrease in molar absorptivity, but also a larger relative stabilization of the frontier orbitals. The limitations in molar absorptivity can thus be mitigated to an extent by increasing the molecule’s effective conjugation path through functionalization with additional conjugated units, but with the countereffect of less-stabilized frontier orbitals.

Organic photovoltaic cells (OPV’s), renewable energy devices that can convert sunlight into electricity, have a bright future. Most OPV’s are made of conjugated polymers since they can absorb light and have semiconducting properties. However, the low power conversion efficiency (PCE) of OPV’s is a challenge in their development. The main structure of OPV’s includes three main parts: an electron donor, an electron acceptor, and electrodes. To improve the PCE of an OPV, many factors need to be considered, such as light absorption, the fundamental gap, the optical gap, and the OPV’s film thickness. The addition of heteroatoms to conjugated polymers is a way to change the electronic properties of the donors and may improve the PCE. This thesis describes the use of computational methods to determine how oxygen and sulfur atoms affect the electronic properties of a conjugated polymer. The data suggest that the fundamental gaps and binding energies decrease after replacing oxygen with sulfur. Additionally, the results also suggest that incorporating a sulfur atom into the conjugated polymer can increase the dipole moment change, which may lead to accelerated charge dissociation and may reduce charge recombination.

Single-walled carbon nanotubes (SWNTs), since their first discovery in early 1990s, have drawn enormous research attention owing to their extraordinary properties. These excellent optical, electrical, thermal and mechanical properties have enabled SWNTs to make profound impacts in the field of nanotechnology, which includes nanoscale nanoelectronics, chemo-/biosensors, photovoltaics, drug delivery, and advanced nanocomposite materials. However, the as-produced SWNT samples contain a mixture of metallic and semiconducting SWNTs, amorphous carbon, and metal catalyst particles. Also, due to π-π stacking and van der Waals forces, pristine SWNTs tend to form bundles, making them insoluble in most of organic solvents. The poor processibility and purity hinder the direct use of as-produced SWNTs as the material for fabrication of SWNT-based devices. Therefore, the post-synthesis purification is highly required. Conjugated polymers have proven to be efficient SWNT dispersants, but after solution processing, conjugated polymers adhered to the sidewall of SWNTs can not be easily removed and thus negatively affect the performance of the resulting SWNT-based electronic devices. Therefore, polymers that can dissociate from the surface of SWNTs after solution processing is highly desirable. Apart from the introduction to several other efficient purification methods of SWNTs, Chapter 1 also gives a brief review on reversible functionalization of SWNTs by polymers. The work reported in the literature categorized by the different external stimuli used to reverse the polymer-SWNT association. Chapter 2 describes the design and synthesis of a vinylogous tetrathiafulvalene (TTFV)-based conjugated polymer, which is responsive to pH changes and thus realized reversible functionalization of SWNTs. Chapter 3 describes the design and synthesis of dithiafulvenyl-grafted phenylene ethynylene polymers, which can reversibly interact with SWNTs by changing solvents. Chapter 4 describes the design and synthesis of dithiafulvene (DTF)-based electron-rich conjugated polymers, which can selectively bind with semiconducting SWNTs. In addition, Chapter 5 describes the use of SEC to achieve high-resolution separation, and isolation of surfactant-free metallic and semiconducting SWNTs. This allowed us to study the competition behavior when different ratios of metallic and semiconducting nanotubes are used as the starting material for polymer dispersions. Finally, Chapter 6 describes a side project that involves covalent functionalization of GO using Piers-Rubinsztajn reaction. The functionalized GO is loaded into silicone elastomer to reduce the air permeability and enhance the mechanical strength of the resulting silicone elastomer. / Thesis / Doctor of Philosophy (PhD)

Le domaine des senseurs chimiques et biochimiques est en pleine expansion, tant au niveau de la recherche fondamentale que du design et de la fabrication de nouveaux « nez artificiels ». Les recherches actuelles visent à la mise au point de dispositifs de taille réduite permettant l’identification et la quantification d’espèces multiples, avec une réponse rapide et réversible, une détection sensible et sélective, le tout intégré dans une technologie simple et peu coûteuse. Les composantes actives des nez artificiels dont il est question ici reposent sur l’utilisation en tant que composante active de polymères et molécules conjugués. Les polymères conjugués sont attractifs pour leur grande sensibilité (tributaire du processus de diffusion efficace des excitations électroniques le long des chaînes) tandis que les molécules conjuguées répondent généralement favorablement au cahier des charges imposé à un senseur, dont les interactions fortes et spécifiques entre le senseur et la molécule à détecter ou encore une grande stabilité chimique et photochimique. Dans ce contexte, le but de cette thèse est d’associer polymères et molécules conjugués pour mettre au point un dispositif hybride combinant les avantages des deux composantes. Afin de caractériser ces dispositifs et de les optimiser, nous nous sommes focalisés dans un premier temps sur l’étude des propriétés géométriques, électroniques et optiques des entités séparées, que nous avons étudiées par le biais de méthodes issues de la chimie quantique. D’une part, nous avons considéré les améliorations pouvant être apportées aux détecteurs moléculaires tant au niveau des limites de détection que de ses propriétés spectroscopiques. D’autre part, nous avons mené une étude mécanistique des processus de transfert d’énergie le long de chaînes de polymères conjugués rigides, en apportant une attention particulière sur les différentes approches envisageables pour en améliorer l’efficacité (effets conformationnels, introduction d’unités à longues durées de vie, écart énergétique donneur-accepteur). Enfin, sur base des résultats obtenus pour les constituants séparés, nous avons proposé des structures chimiques de systèmes ‘hybrides’, constitués de polymères conjugués substitués en bouts de chaîne par des groupements ionophores. Ces études ont été menées en étroite collaboration avec le groupe du Prof. Noël Boens à la KULeuven, où les molécules et polymères conjuguées étudiés théoriquement dans le cadre de ce travail ont été synthétisés et caractérisés d’un point de vue spectroscopique.

Conjugated polyelectrolytes (CP) show interesting electrical and optical properties for organic electronics as well as for life science applications. Their possibilities of supramolecular assembly with nanowire like misfolded proteins, amyloids, as well as synthetic polypeptides or DNA forming conducting nano composites is highly interesting as being a truly bottom up approach for fabrication of OLEDs, photovoltaic’s as well as logic devices. A special class of CPs is that of electroactive cojugated polymers (ECPs), which, due to their structure, will exhibits a unique combination of properties, including the following; electrically conducting, ability to store an electric charge and ability to exchange ions. The positive or negative excess charge can be introduced into the conjugated polymer by means of chemical or electrochemical oxidation/reduction (a process called doping) following the polymerization reaction. In order to preserve overall electroneutrality of the polymer during introduction of excess charge, ionexhange processes occurs between the polymer phase and the surrounding electrolyte solution. This charge/discharge process can be utilized for application such as; pseudo super capacitors (energy storage through oxidation/reduction processes), electro mechanical actuators (convert electrical energy to mechanical energy) and sensors (converts a chemical signal to electrical conductivity). In this thesis we describes the synthetic challenges with ECPs for applications vide supra. These mostly relates to solubility, ionic functionalization, conductivity and macromolecular properties such as size and shape of the ECPs. The key requirement in the synthesis of ECPs is that the conjugated nature of the monomer is conserved in the synthesis process and that insertion of excess charge (doping) can be obtained. This limits both the choice of monomer and the choice of polymerization process. Monomers of great complexity have been synthesized with this careful goal in mind. Furthermore, the development of novel monomers must also target the appropriate functionality for polymerization. As such, most ECP monomers are electron-rich molecules with pendant groups containing pyrroles, thiophenes, or 3,4-ethylenedioxythiophenes. These three well known ECP monomers are excellent additions to conjugated systems as they typically enable electrochemical polymerization and direct the polymerizations toward linear polymers with good stability towards doping. The first topic of this thesis we demonstrate how we can obtain water soluble ECPs with good electrical conductivity by controlling the polymerization techniques and proper ionic functionalization of the monomer. We also show how these polymers can be incorporated by self-assembly with biomolecular templates, such as, DNA and amyloid fibrils, thus generating novel electrically conductive nanowires. The second topics of this thesis demonstrate how hydrogels of ECPs can be used as bioand charge storage materials, were we demonstrate electronically controlled cell release for biology applications. Both applications are based on ECPs ability to ionexhange processes during electrochemical redox reactions. As well as ions, solvent and other neutral molecules may enter the film during charge/discharge processes. This cause a swelling or shrinking of the ECP films and the expansion and contraction of the polymer network in conjugation with the sorption/desorption of solvent molecules and ions can be described in terms of mechanical work. In the first case we were able to synthesize a water soluble ECP with high amphiphilic character. The polymer was immobilized onto a flexible electrode, suitable for cell growth and subjected to a cell growth media. When the desired cell layer was formed we applied a potential to the flexible electrode. This resulted in that the mechanical work of the immobilized ECP during the applied potential overcame the week adhesive forces to the flexible electrode, which resulted in super swelling and disintegration of the ICP and the cell layer could be harvested. In the second case the possibilities of using synthetically modified ECPs as a dopant during electropolymerization of another ECP monomer to obtain a polymer integrated network with high charge density and good charge transport properties. We demonstrate how this polymer network can be used as porous electrodes suitable for supercapacitors.

Conjugated polymers have been found useful in a wide range of applications such as solar cells, sensor elements and printed electronics, due to their optical and electronic properties. Functionalization with charged side chains has enabled water solubility, resulting in an enhanced interaction with biomolecules. This thesis focus on the emerging research fields, where these conjugated polyelectrolytes (CPEs) are combined with biomolecules for biological sensing and DNA nanowire assembling. CPEs have shown large potential in biomolecular detection where the optical read out is due to the geometrical alternation in the backbone and aggregation state. This thesis focused on transferring the biomolecular detection to a surface of CPEs. The characterization of the CPE layer show that a hydrogel can be formed, and how the layer can undergo geometrical changes upon external stimulus such as pH change. A selective sensor surface can be created by imprinting ssDNA or an antibody in the CPE layer. The discrimination for complementary DNA hybridization and specific antibody interaction can be monitored by surface plasmon resonance or quartz crystal microbalance. We have also taken the step out from the controlled test tube experiments to the complex environment of the cell showing the potential for staining of compartments and structures in live and fixed cell. Depending on the conditions and CPE used, cell nuclei, acidic vesicles and cytoskeleton structure can be visualized. Furthermore, the live staining shows no sign of toxic effect on cultured fibroblasts. CPEs can also be a valuable element when assembling electronics in the true nano regime. I have used DNA as building template due to its attractive size features, with a width of around 2 nm and a length scale in the µm regime, and the inbuilt base-paring recognition elements. This thesis shows how DNA can be decorated with CPEs and stretched on surfaces into a model for aligned semiconducting nanowire geometries. Not only making the template structures is of importance, but also how to place them on the correct surface position, i.e. on electrodes. Strategies for positioning DNA nanowires using transfer printing and surface energy patterning methods have therefore been developed in the thesis. The stretched DNA decorated with CPE also offers a way to further study the molecular binding interaction between the two molecules. Single molecular spectroscopy in combination with polarization has given information of the variation of the CPE binding along a DNA chain.