11 |
Corrosion resistance of modified β-EucryptiteBattu, Laurent P. 14 August 2009 (has links)
The corrosion resistance of chemically modified β-eucryptite (Li<sub>0.41</sub>Mg<sub>0.035</sub>AlP<sub>0.52</sub>Si<sub>0.48</sub>0₄) having low expansion anisotropy and a near zero coefficient of thennal expansion was evaluated. Samples were exposed to aqueous hydrochloride acid at temperatures up to 100°C and environments containing sodium sulfate up to l000°C. The corrosion resistance was characterized by dilatometry, scanning electron microscopy, X-ray diffraction, energy dispersive x-ray analysis, weight variations, and mechanical properties variations.
The results show that modified β-eucryptite is more severely corroded than commercial lithium-alumina-silicate glass-ceramics when exposed to these environments. Aqueous HCI removes AIP04 from modified β-eucryptite leaving a very porous structure. Molten salt corrodes modified β-eucryptite by penetration of sodium and sulfur which form an alkali melt under the surface. The modulus of rupture and the Young's modulus are reduced by both types of corrosion. / Master of Science
|
12 |
Alkali/steam corrosion resistance of commercial SiC products coated with sol-gel deposited Mg-doped Al₂TiO₅ and CMZPKang, Min 08 April 2009 (has links)
The corrosion resistance of two commercially available SiC filter materials coated with Mg-doped Al₂ TiO₅ and (Ca <sub>0.6</sub>.6' Mg<sub>0.52</sub>) Zr₄P₆O₂₄ (CMZP) was investigated in high-temperature high pressure (HTHP) alkali-steam environments. Coated specimen properties, including cold and hot compressive strengths, bulk density, apparent porosity, permeability, and weight change, detected after exposure to 92% air-S% steam 10 ppm Na at 8OO°C and 1.8 MPs for 500 h were compared with those of uncoated specimens. Procedures for applying homogeneous coatings of Mg-doped Al₂ TiO₅ and CMZP to porous SiC filters were established and coating of the materials was successfully accomplished. Efforts to stabilize the Al₂ TiO₅ coating composition at elevated temperature were successful. Coatings show promise for providing improved corrosion resistance of the materials in pressurized fluidized bed combustion (PFBC) environments as evidenced by higher compressive strengths exhibited by coated SiC specimens than by uncoated SiC specimens following HTHP alkali-steam exposure. / Master of Science
|
13 |
Surface Modifications of Steels to Improve Corrosion Resistance in Sulfidizing-Oxidizing EnvironmentsBehrani, Vikas 26 September 2007 (has links)
Industrial and power generation processes employ units like boilers and gasifiers to burn sulfur containing fuels to produce steam and syn gas (H2 and CO), which can generate electricity using turbines and fuel cells. These units often operate under environments containing gases such as H2S, SO2, O2 etc, which can attack the metallic structure and impose serious problems of corrosion. Corrosion control in high temperature sulfur bearing environments is a challenging problem requiring information on local gaseous species at the surface of alloy and mechanisms of degradation in these environments. Coatings have proved to be a better alternative for improving corrosion resistance without compromising the bulk mechanical properties. Changes in process conditions may result in thermal and/or environment cycling between oxidizing and sulfidizing environments at the alloy surface, which can damage the protective scale formed on the alloy surface, leading to increase in corrosion rates. Objective of this study was to understand the effect of fluctuating environments on corrosion kinetics of carbon steels and develop diffusion based coatings to mitigate the high temperatures corrosion under these conditions. More specifically, the focus was : (1) to characterize the local gaseous environments at the surface of alloys in boilers; (2) optimizing diffusion coatings parameters for carbon steel; (3)understand the underlying failure mechanisms in cyclic environments; (4) to improve aluminide coating behavior by co-deposition of reactive elements such as Yttrium and Hafnium; (5) to formulate a plausible mechanism of coating growth and effects of alloying elements on corrosion; and (6) to understand the spallation behavior of scale by measuring stresses in the scales. The understanding of coating mechanism and effects of fluctuating gaseous environments provides information for designing materials with more reliable performance. The study also investigates the mechanism behind the effect of REs on scale adhesion and sulfidation behavior. Thus, the present work will have a broad impact on the field of materials and coatings selection for high temperature industrial environments such as boilers and gasifiers, and provides information on RE-modified aluminized coatings on carbon steel as an alternative for the use of bulk superalloys under high temperature sulfur bearing environments.
|
14 |
High-strength stainless steels for corrosion mitigation in prestressed concrete: development and evaluationMoser, Robert David 16 May 2011 (has links)
The use of stainless steel alloys in reinforced concrete structures has shown great success in mitigating corrosion in even the most severe of exposures. However, the use of high-strength stainless steels (HSSSs) for corrosion mitigation in prestressed concrete (PSC) structures has received limited attention. To address these deficiencies in knowledge, an experimental study was conducted to investigate the feasibility of using HSSSs for corrosion mitigation in PSC. The study examined mechanical behavior, corrosion resistance, and techniques for the production of HSSS prestressing strands. Stainless steel grades 304, 316, 2101, 2205, 2304, and 17-7 along with a 1080 prestressing steel control were included in the study. Tensile strengths of 1250 to 1550 MPa (181 to 225 ksi) were achieved in the cold-drawn HSSSs. 1000 hr stress relaxation of all candidate HSSSs was predicted to be between 6 and 8 % based on the results of 200 hr tests conducted at 70 % of the ultimate tensile strength. Residual stresses due to the cold drawing had a significant influence on stress vs. strain behavior and stress relaxation. Electrochemical corrosion testing found that in solutions simulating alkaline concrete, all HSSSs showed exceptional corrosion resistance at chloride (Cl-) concentrations from zero to 0.25 M. However, when exposed to solutions simulating carbonated concrete, corrosion resistance was reduced and the only HSSSs with acceptable corrosion resistance were duplex grades 2205 and 2304, with 2205 resistant to corrosion initiation at Cl- concentrations up to 1.0 M (twice that in seawater). Based on these results, duplex grades 2205 and 2304 were identified as optimal HSSSs and were included in additional studies which found that: (1) 2304 is susceptible to corrosion when tested in a stranded geometry, (2) 2205 and 2304 are not susceptible to stress corrosion cracking, and (3) 2205 and 2304 are susceptible to hydrogen embrittlement. Efforts focused on the production of 2205 and 2304 prestressing strands showed that they could be produced as strands using existing ASTM A416 prestressing strand production facilities. Due to the ferromagnetic properties of 2205 and 2304, a low-relaxation heat treatment was found to be a viable option to reduce stress relaxation and improve mechanical properties. The overall conclusion of the study was that HSSSs, especially duplex grades 2205 and 2304, show excellent promise to mitigate corrosion if utilized as prestressing reinforcement in PSC structures exposed to severe marine environments.
|
15 |
Short term observations of in vitro biocorrosion of two commonly used implant alloysLin, Hsin-Yi. January 2002 (has links)
Thesis (Ph. D.)--Mississippi State University. Department of Agricultural and Biological Engineering. / Title from title screen. Includes bibliographical references.
|
16 |
Microestrutura de solidificação e resistencias mecanicas e a corrosão de ligas Pb-Sn diluidas / Solidification microstructures and mechanical and corrosion resistances of dilute Pb-Sn alloysPeixoto, Leandro César de Lorena 13 August 2018 (has links)
Orientadores: Amauri Garcia, Wislei Riuper Osorio / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecanica / Made available in DSpace on 2018-08-13T18:01:29Z (GMT). No. of bitstreams: 1
Peixoto_LeandroCesardeLorena_M.pdf: 5871010 bytes, checksum: f7403606c814ec8a30965352f0a93e87 (MD5)
Previous issue date: 2009 / Resumo: Produtores de baterias chumbo-ácido têm modificado os processos de produção e composição química das ligas utilizadas nas grades das baterias com intuito de diminuir o seu peso final, bem como reduzir os custos de produção e também aumentar o ciclo de vida útil e a resistência à corrosão. As morfologias das estruturas de solidificação, caracterizadas principalmente por arranjos celulares e dendríticos, e suas grandezas representadas por espaçamentos celulares e dendríticos controlam a distribuição de soluto, segundas fases dentro das regiões intercelulares ou interdendríticas, que determinam as propriedades finais. O comportamento mecânico e as características estruturais dos componentes de bateria têm papel importante no desempenho das baterias. O presente trabalho pretende contribuir para o entendimento do desenvolvimento microestrutural de ligas diluídas do sistema Pb-Sn (Pb-1,0%Sn e Pb-2,5%Sn) que possuem elevada importância para a indústria na fabricação de componentes de baterias automotivas e estacionárias. Os experimentos de solidificação realizados em dispositivo no qual o calor é extraído somente pelo sistema de resfriamento a água, localizado na base do conjunto lingote/lingoteira (solidificação ascendente). As variáveis térmicas de solidificação foram determinadas a partir do registro de temperaturas de termopares posicionados dentro da lingoteira em diferentes posições em relação à superfície refrigerada do lingote. Amostras das mencionadas ligas Pb-Sn foram utilizadas para analisar as influências das variáveis térmicas de solidificação e da concentração de soluto nas macro e microestruturas resultantes e na resistência mecânica. Foram determinados os limites de resistência à tração e alongamentos específicos em função do espaçamento celular e a influência da microestrutura no comportamento eletroquímico foi avaliada por intermédios dos ensaios de espectroscopia de impedância eletroquímica, extrapolação de Tafel, curvas de polarização e análise por circuito equivalente em solução eletrolítica de ácido sulfúrico. Observou-se que a resistência a corrosão diminui e o limite de resistência a tração aumenta com a diminuição do espaçamento celular. / Abstract: Lead-acid batteries manufacturers have modified the manufacturing processes and the chemical composition of alloys used in battery grids in order to decrease their weight as well as to reduce the production costs, and to increase the battery life-time cycle and the corrosion-resistance. The morphological microstructures characterized by cellular and dendritic arrays and its correspondents cellular and dendrite arm spacings control the solute distribution, second phases in the intercellular and interdendritic regions affecting the resulting properties. The mechanical behavior and microstructural characteristics of lead-acid battery components have an important role in the battery performance. The present work aims to contribute to the understanding of the microstructural development of dilute Pb-1,0 wt.%Sn and Pb-2.5 wt.%Sn alloys which are widely applied in the manufacturing of automobile and stationary lead-acid batteries. A water-cooled vertical upward unidirectional solidification system was used to obtain the samples. The experimental set-up was designed in such a way that the heat was extracted only through the water-cooled bottom, promoting upward directional solidification. Thermal readings were obtained by thermocouples positioned at different distances from the heat-extracting surface at the casting bottom. Pb-Sn alloy samples were used to analyze the effects of the thermal solidification variables and solute content on the resulting macro and microstructures and on the mechanical properties.
The ultimate tensile strength and the elongation were determined as a function of the cellular arm spacing. The effect of the resulting microstructure on the electrochemical corrosion behavior was also analyzed based on electrochemical parameters, determined by Tafel plots, polarization curves and an equivalent circuit analysis after corrosion tests carried out in a sulphuric acid solution. It was observed that the corrosion resistance decreases and the ultimate tensile strength increases with decreasing cellular spacing. / Mestrado / Materiais e Processos de Fabricação / Mestre em Engenharia Mecânica
|
17 |
An analysis of the performance of a South African stainless steel manufacturer in localising the demand for corrosion resistant steels within the Eastern Cape catalytic converter industrySoiné, Robert Paul January 2004 (has links)
Commercial decisions are been made with respect to the competitive advantage of manufacturing catalytic converters in South Africa. This thesis identifies those factors relating to the sourcing of stainless steel and the impact it has of securing future business in a competitive environment. The catalytic converter industry requires the support of a stainless steel plant that provides high quality products at a competitive price, while keeping abreast with international developments.
|
18 |
Effect of Amines as Corrosion Inhibitors for a Low Carbon Steel in Power IndustryDíaz, Jorge G. 12 1900 (has links)
Commonly used amines in power industry, including morpholine, DBU (1,8-diazabicyclo[5.4.0]undec-7-ene), and DMA (dimethylallylamine) were evaluated for their effect on AISI 1018 steel at 250oF. Samples were exposed to an autoclave containing amine added aqueous solution at pH of 9.5 for 1, 2, 4, 6, 8, and 12 hours. Morphology studies were carried using scanning electron microscope (SEM), phase analysis was done utilizing Fourier transform infrared spectroscopy (FTIR), and weight loss was performed to assess kinetics of oxidation. Control samples showed the highest metal dissolution rate. DBU showed the best performance in metal protection and SEM indicated the presence of a free-crack layer formed by fine particles in that set. FTIR showed that DBU apparently favored the formation of magnetite. It is believed that fine particles impede intrusion of aggressive ions into the metal surface by forming a barrier layer. FTIR demonstrated that DMA formed more oxyhydroxides, whereas morpholine presented magnetite to hematite transformation as early as 2 hours. SEM revealed that control and DMA produced acicular particles characteristic of oxyhydroxides while morpholine and DBU presented more equiaxed particles.
|
19 |
Bioinspired & biocompatible coatings of poly(butylene adipate-co-terephthalate) and layer double hydroxide composites for corrosion resistanceRizvi, Hussain R. 05 1900 (has links)
Hierarchical arrangement of biological composites such as nacre and bone containing high filler (ceramic) content results in high strength and toughness of the natural material. In this study we mimic the design of layered bone microstructure and fabricate an optimal multifunctional bio-nanocomposite having strength, toughness and corrosion resistance. Poly (butylene adipate-co-terephthalate) (PBAT), a biodegradable polymer was used as a substrate material with the reinforcement of LDH (Layered double hydroxide) as a nanofiller in different concentrations to achieve enhancement in mechanical properties as well as processing related thermostability. Corrosion resistance was increased by mimicking a layered structured which incorporated a tortuous diffusion path.
|
20 |
Electrodeposition of Nickel and Nickel Alloy Coatings with Layered Silicates for Enhanced Corrosion Resistance and Mechanical PropertiesTientong, Jeerapan 08 1900 (has links)
The new nickel/layered silicate nanocomposites were electrodeposited from different pHs to study the influence on the metal ions/layered silicate plating solution and on the properties of the deposited films. Nickel/layered silicate nanocomposites were fabricated from citrate bath atacidic pHs (1.6−3.0), from Watts’ type solution (pH ~4-5), and from citrate bath at basic pH (~9). Additionally, the new nickel/molybdenum/layered silicate nanocomposites were electrodeposited from citrate bath at pH 9.5. The silicate, montmorillonite (MMT), was exfoliated by stirring in aqueous solution over 24 hours. The plating solutions were analyzed for zeta potential, particle size, viscosity, and conductivity to investigate the effects of the composition at various pHs. The preferred crystalline orientation and the crystalline size of nickel, nickel/layered silicate, nickel/molybdenum, and nickel/molybdenum/layered silicate films were examined by X-ray diffraction. The microstructure of the coatings and the surface roughness was investigated by scanning electron microscopy and atomic force microscopy. Nickel/molybdenum/layered silicate nanocomposites containing low content of layered silicate (1.0 g/L) had increase 32 % hardness and 22 % Young’s modulus values over the pure nickel/molybdenum alloy films. The potentiodynamic polarization and electrochemical impedance measurements showed that the nickel/molybdenum/layered silicate nanocomposite layers have higher corrosion resistance in 3.5% NaCl compared to the pure alloy films. The corrosion current density of the nickel/molybdenum/layered silicate nanocomposite composed of 0.5 g/L MMT is 0.63 µA·cm-2 as compare to a nickel/molybdenum alloy which is 2.00 µA·cm-2.
|
Page generated in 0.1634 seconds