Yes / Multistage Flash Desalination (MSF) is currently facing an enormous challenge in cutting of the cost: within the last few years, the MSF experienced a gradual decline in investment compared to other techniques of desalting water and thus, a significant improvement is required to remain attractive for capital investors. Improved process control is a cost effective approach to energy conservation and increased process profitability. In this work, a dynamic model is presented using gPROMS model builder to optimize and control MSF process. The Proportional Integral Derivative Controller (PID) and Generic Model Control (GMC) are used successfully to control the Top Brine Temperature (TBT) and the Brine Level (BL) in the last stage at different times of the year. The objectives of this study are: firstly, to obtain optimum TBT and BL profiles for four different seasons throughout the year by minimizing the Total Seasonal Operating Cost (TSOC); secondly, to track the optimum TBT and BL profiles using PID and GMC controllers with and without the presence of constraints; thirdly, to examine how both types of controllers handle the disturbances which occur in the plant. The results are promising and show that GMC controller provides better performance over conventional PID controller to handle a nonlinear system.

Yes / The coupling of thermal (Multi Stage Flash, MSF) and membrane processes (Reverse Osmosis, RO) in desalination systems has been widely presented in the literature to achieve an improvement of performance compared to an individual process. However, very little study has been made to the combined Multi Effect Distillation (MED) and Reverse Osmosis (RO) processes. Therefore, this research investigates several design options of MED with thermal vapor compression (MED_TVC) coupled with RO system. To achieve this aim, detailed mathematical models for the two processes are developed, which are independently validated against the literature. Then, the integrated model is used to investigate the performance of several configurations of the MED_TVC and RO processes in the hybrid system. The performance indicators include the fresh water productivity, energy consumption, fresh water purity, and recovery ratio. Basically, the sensitivity analysis for each configuration is conducted with respect to seawater conditions and steam supply variation. Most importantly, placing the RO membrane process upstream in the hybrid system generates the overall best configuration in terms of the quantity and quality of fresh water produced. This is attributed to acquiring the best recovery ratio and lower energy consumption over a wide range of seawater salinity.

Yes / Despite the fact of being intensive energy consumption, MSF is a mature technology that characterised by a high production capacity of high-quality water. The multistage flash (MSF) desalination process is one of the prominent thermal desalination used in the industry of seawater desalination to produce high quantity and high quality of freshwater. However, this process consumes large amount of energy and faces thermal limitations due to its high degree of exergy destruction at several units of the process. Therefore, the research of MSF is still existed to elevate the performance indicators and to resolve the concern of high energy consumption. To rectify these limitations, it is important to determine the units responsible in dissipating energy. This study aims to model an industrial MSF process validated against real data and then investigate the exergy destruction and thermodynamic limitations of the process. As a case study, Azzour MSF seawater desalination plant, located in Al Khiran in Kuwait is under the focus. A comprehensive model is developed by analysing several published models. Specifically, the calculation of exergy destruction has embedded both physical and chemical exergies that identified as a strong point of the model developed. As expected, the highest exergy destruction (55.5%) occurs within the heat recovery section followed by the brine heater with exergy destruction of 28.26% of the total exergy destruction. This study identifies the sections of the industrial process that cause the highest energy losses.

Yes / The use of solar thermal energy for water desalination processes is increasing rapidly, particularly in areas where these resources are plentiful. However, solar energy plants are highly affected by the intermittency of day -night cycles and by low irradiation seasons. Although biomass fuel can be used as source of energy for thermal desalination processes, these resources are becoming increasingly scarce, expensive and seasonally available. Integration of solar-biomass technologies for water desalination process may provide the solution to these challenges. This work investigates design options of the Humidification-Dehumidification desalination system integration with the solar-biomass energies. The investigation is based on simulation of the process models in gPROMS platform. Results show that the solar-biomass integrated plant with a thermal storage system can save up to 57 % of the daily energy cost compared to conventional biomass plant. The integrated plant also cuts the CO2 emission by 59 %. Moreover, it has higher daily production capacity than conventional solar plants. / The authors wish to thank the Commonwealth Scholarship Commission in the UK (CSC) for financial support under PhD Scholarships Plan for Low and Middle Income Countries.

Yes / The shortage of fresh water resources is a global problem which requires a prompt solution. Thus, the multi effect distillation (MED) was successfully used for the production of fresh water from seawater. Despite the use of MED desalination system extensively, the influence of the number of effects on the fresh water production cost has not been covered in the open literature. Thus, this paper tries to rectify this specific challenge via simulation at given operating conditions of seawater salinity and temperature. The study is performed using a detailed mathematical model contains the suitable cost correlations. gPROMS model builder suite has been used to carry out an extensive simulation. The results of the study show that the lowest fresh water production cost can be achieved at an optimal number of effects of 17 for a certain operating conditions.

Yes / The reverse osmosis (RO) process is one of the most popular membrane technologies for the generation of freshwater from seawater and brackish water resources. An industrial scale RO desalination consumes a considerable amount of energy due to the exergy destruction in several units of the process. To mitigate these limitations, several colleagues focused on delivering feasible options to resolve these issues. Most importantly, the intention was to specify the most units responsible for dissipating energy. However, in the literature, no research has been done on the analysis of exergy losses and thermodynamic limitations of the RO system of the Arab Potash Company (APC). Specifically, the RO system of the APC is designed as a medium-sized, multistage, multi pass spiral wound brackish water RO desalination plant with a capacity of 1200 m3/day. Therefore, this paper intends to fill this gap and critically investigate the distribution of exergy destruction by incorporating both physical and chemical exergies of several units and compartments of the RO system. To carry out this study, a sub-model of exergy analysis was collected from the open literature and embedded into the original RO model developed by the authors of this study. The simulation results explored the most sections that cause the highest energy destruction. Specifically, it is confirmed that the major exergy destruction happens in the product stream with 95.8% of the total exergy input. However, the lowest exergy destruction happens in the mixing location of permeate of the first pass of RO desalination system with 62.28% of the total exergy input.

Yes / Clean water demand has significantly increased due to the rise in the global population. However, most water on the Earth has high saline content that cannot be consumed directly; only about one over forty of the total water source is freshwater. Desalinated water is one of the potential solutions to meet the growing demand for freshwater, which is highly energy intensive. This paper analyses the energy, economic and environmental performance of a 5 m3/day PV (photovoltaic) powered reverse osmosis (RO) desalination system. Three scenarios of PV-RO with and without battery storage and diesel generator hybrid systems have been analyzed and investigated for the annual estimate load, net present value, and payback period of the water and electricity production costs. Also, the CO2 avoidance over the lifetime operation of all scearios is evaluated. This study shows that the PV-RO system without battery with 6.3 kW PV panels installed and with a 2-days water storage tank system is the most profitable economically f. For this scenario, the Levelized Cost of Electricity (LCOE), Levelized Cost of Water (LCOW), and Payback Period (PBP) are found to be $0.154/kWh, $0.627/m3, and five years, respectively. In addition, for this scenario, the CO2 emissions avoidance was the maximum (111,690 kg.CO2eq per year) compared to other scenarios.

Yes / Reverse Osmosis (RO) process has become one of the most widely utilised technologies for brackish water desalination for its capabilities of producing high-quality water. This paper emphasis on investigating the feasibility of implementing the retentate recycle design on the original design of an industrial medium-sized multistage and multi-pass spiral wound brackish water RO desalination plant (1200 m³/day) of Arab Potash Company (APC) located in Jordan. Specifically, this research explores the impact of recycling the high salinity stream of the 1st pass (at different recycled percentages) to the feed stream on the process performance indicators include, the fresh water salinity, overall recovery rate, and specific energy consumption. The simulation is carried out using an earlier model developed by the same authors for the specified RO plant using gPROMS suits. This confirmed the possibility of increasing the product capacity by around 3% with 100% recycle percentage of the high salinity retentate stream.

Yes / The desalination of saltwater is a viable option to produce freshwater. All the desalination processes are energy-intensive and can be carried out on a large scale. Therefore, producing freshwater using renewable energy sources is the most desirable option considering the current energy crisis and the effect that fossil-fuel-based energy has on our carbon footprint. In this respect, the tray-type still, one of several solar power desalination still varieties, is popular owing to its straightforward design, economic materials of construction, and minimal maintenance requirements, especially in isolated island regions with restricted energy and natural water supplies. The traditional tray-type solar power has a few drawbacks, such as the inability to recover latent heat from condensation, reduced thermal convection, a large heat capacity, and comparatively minimal driving power through evaporation. Therefore, the improvement of heat and mass transfer capabilities in tray-type stills has been the subject of many studies. However, there is a lack of a comprehensive review in the open literature that covers the design and operational details of multistage solar stills. The purpose of this paper is to present a thorough overview of the past research on multistage solar stills, in terms of configurations, capabilities, and cutting-edge options. In comparison to a unit without a salt-blocking formation, the review indicates that a multistage distillation unit may run continuously at high radiation and generate pure water that is around 1.7 times higher than a unit without a salt-blocking formation. The most effective deign is found to be “V”-shaped solar still trays that attach to four-stage stills, since they are less expensive and more economical than the “floor” (Λ-shape) design, which requires two collectors. Additionally, it can be stated that the unit thermal efficiency, solar percentage, and collected solar energy (over the course of a year) increase by 23%, 18%, and 24%, respectively, when the solar collectors are increased by 26% (at the constant inflow velocity of the water).

Yes / Desalination has become one of the obvious solutions for the global water crisis due to affording high-quality water from seawater and brackish water resources. As a result, there are continuing efforts being made to improve desalination technologies, especially the one producing high-quantity freshwater, i.e., thermal desalination. This improvement must be accomplished via enhancement of process design through optimization which is implicitly dependent on providing a generic process model. Due to the scarcity of a comprehensive review paper for modeling multi-effect distillation (MED) process, this topic is becoming more important. Therefore, this paper intends to capture the evolution of modeling the forward feed MED (most common type) and shed a light on its branches of steady-state and dynamic modeling. The maturity of the models developed for MED will be thoroughly reviewed to clarify the general efforts made highlighting the advantages and disadvantages. Depending on the outputs of this review, the requirements of process development and emerging challengeable matters of modeling will be specified. This, in turn, would afford a possible improvement strategy to gain a reliable and sustainable thermal desalination process.