Titania has been the focus of attention for several decades owing to its chemical stability, non-toxicity, inexpensiveness and robust surface chemistry. Its technological applications include use in diverse areas such as photocatalytic reactors, antibacterial coatings, dye sensitive solar cells (DSSC) and more recently the perovskite solar cells to name a few. All of these applications are based on the ability to inject or generate electronhole pairs in titania and transport them to a suitable interface at which they are ejected to either engender a reaction as in photocatalysis or drive a load as in photovoltaics. From a technological perspective it is also important that such science be achieved and controlled in supported titania structures. The research reported in this thesis, thus, started with the development of a process for obtaining adherent titania films by oxidation of sputtered Ti films on stainless steel, a very commonly used substrate. Challenges that had to be overcome included the need to oxidize titanium to obtain the right phase mixture while preventing film cracking or delamination due to compressive stresses generated during anodic oxidation of Ti. During this process of obtaining nanostructured TiO2 through anodization, it was serendipitously discovered that planar TiO2 films obtained by oxidation of sputtered Ti films did significantly better than anodized nanoporous titania in bactericidal studies. This was then replicated in organic dye degradation studies. Analysis of the material showed that this improved performance was due to the unintentional contamination during sputtering by Cu, Zn, Mo possibly due to arcing across brass contacts. This quaternary system was then systematically explored and it was shown that an optimal metastable composition in the Ti- Cu-Mo oxide ternary system performs the best. DFT studies showed that this was due to introduction of shallow and deep states in the band gap that, depending on the level of dopants, either enhances carrier lifetimes or leads to recombination. In continuation of this work on supported titania structures by oxidation of Ti, a novel photoanode for use in dye sensitized photovoltaics was developed by oxidation of Ti foam. This results in an interconnected 3-D network of TiO2 that possess at its core a network of Ti. Such architecture was designed to provide a large surface area for anchoring the sensitizer while simultaneously reducing the distance that charge carriers have to travel before reaching the ohmic contacts to prevent recombination losses. The thesis discusses the preparation of such anodes, the properties of the 3-D oxide and cells, with up to 4% efficiency, developed using such anodes. Reasons for such behaviour and avenues for further exploration to improve cell efficiency will also be discussed.

Photovoltaic cells are a promising solution to the current energy crisis. Among the different photovoltaic cell technologies developed, dye-sensitised solar cells (DSSC) are emerging as viable low-cost alternatives to Si PV technology. This thesis presents studies on fabrication and characterisation of TiO2 based dye-sensitised solar cells. Chapter 1 gives an overview of different photovoltaic cell technologies and a review of the state-of-the art DSSC technology. Chapter 2 describes the techniques used for characterisation of DSSCs. Chapter 3 describes the fabrication of TiO2 based dye-sensitised solar cells. Chapter 4 presents the analysis of measurements obtained by the characterisation techniques. Finally chapter 5 summarises the work done and suggests directions for future work.

Exploring new technologies that can meet the world’s energy demands in an efficient and clean manner is critically important due to the depletion of natural resources and environmental concerns. Dye-sensitized solar cells (DSSCs) are low-cost and clean technology options that use solar energy efficiently and are being intensively studied. How to further reduce the cost of this technology while enhancing device performance is one of the demanding issues for large scale application and commercialization of DSSCs. In this research dissertation, four main contributions are made in this regard with the motivation to reduce further cost of DSSC technology. Firstly, ~10% efficiencies were achieved after developing understanding of key concepts and procedures involved in DSSCs fabrication. These efficiencies were achieved after step-by-step modifications in the DSSC design. Secondly, carbon nanotubes (CNTs) were successfully employed as an alternative to Pt in the counter electrodes of DSSCs. DSSCs fabricated with CNTs were ~86% as efficient as Pt-based cells. Non-aligned CNTs were successfully grown using four different CVD methods and finally, multi-walled vertically aligned CNTs (MW-VACNTs) were synthesized using water-assisted chemical vapor deposition (WA-CVD). Thirdly, carbon derived from pyrolysis of nanocrystalline cellulose (NCC) was successfully employed in counter electrodes of DSSCs instead of Pt. DSSCs with NCC were ~58% as efficient as Pt-based DSSCs. Fourthly, novel organic metal-free dyes were designed and employed instead of commonly used Ru-based dyes. DSSCs with these novel sensitizers were ~62% as efficient as those using the conventional Ru-based dyes. Characterization techniques including current-voltage measurements, scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), cyclic voltammetery (CV), thermogravimetric analysis (TGA), small angle x-ray scattering (SAXS), atomic force microscopy (AFM) and x-ray photoelectron spectroscopy (XPS) were used.

This work investigates the correlation of structural and photovoltaic properties of dyes used in dye-sensitized solar cells. Experimental methods, including ultraviolet-visible spectroscopy, fluorescence spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy are employed to study optical and electrochemical properties of dye molecules. Computational methods, including density functional theory and time-dependent density functional theory, are used to validate and predict the optical and electronic properties of dye molecules, in their isolated state and once embedded into a working electrode device environment that comprises a dye...TiO2 interface. The results chapters begin with the presentation of a series of quinodimethene dyes that are experimentally validated for their photovoltaic application, and associated computational studies reveal that an inner structural factor - a phenyl ring rotation occurring during the optical excitation process - leads to the competitive photovoltaic device performance of these dyes. Carbazole-based dyes are then systematically studied by computation, especially considering charge transfer paths and binding modes of these dyes on a titania surface. The theoretical models for the basic building block of this chemical family of dyes, known as MK-44, successfully support and explain structural discoveries from X-ray diffraction and reflectometry that impact of their function. A benzothiadiazole-based dye, RK-1, is then systematically studied by both experimental and computational methods, and the results show that the π-bridge composed of thiophene, benzothiadiazole and benzene rings leads to excellent charge separation; and the rotation of these rings during the optical excitation process may well be consistent with the fluorescence spectrum. Finally, the well-known ruthenium-based dyes are theoretically studied to determine the properties of different ligands connected to the metal core of the complex. Conformations with different NCS ligands are calculated in terms of energy and explain well the corresponding results from X-ray diffraction. Acid-base properties of carboxyl groups connected to pyridine ligands in N3 and N749 are theoretically calculated based on thermodynamics and density functional theory. Implicit and explicit models are both adopted to predict these acid dissociative constant values, which are generally in a good agreement with the reported experimental data. The thesis concludes with conclusions and a future outlook.

Ce projet de recherche mené en collaboration industrielle avec St-Jean Photochimie Inc. / PCAS Canada vise le développement et la caractérisation de dérivés dipyrrométhène pour des applications dans le domaine du photovoltaïque. La quête du récoltage des photons se situant dans le proche-infrarouge a été au centre des modifications structurales explorées afin d’augmenter l’efficacité de conversion des cellules solaires de type organique et à pigments photosensibles. Trois familles de composés intégrant le motif dipyrrométhène ont été synthétisées et caractérisées du point de vue spectroscopique, électrochimique, structural ainsi que par modélisation moléculaire afin d’établir des relations structures-propriétés. La première famille comporte six azadipyrrométhènes au potentiel de coordination tétradentate sur des centres métalliques. Le développement d’une nouvelle voie synthétique asymétrique combinée à l’utilisation d’une voie symétrique classique ont permis d’obtenir l’ensemble des combinaisons de substituants possibles sur les aryles proximaux incluant les noyaux 2-hydroxyphényle, 2-méthoxyphényle et 2- pyridyle. La modulation du maximum d’absorption dans le rouge a pu être faite entre 598 et 619 nm. De même, la présence de groupements méthoxyle ou hydroxyle augmente l’absorption dans le violet (~410 nm) tel que démontré par modélisation. La caractérisation électrochimique a montré que les dérivés tétradentates étaient en général moins stables aux processus redox que leur contre-parti bidentate. La deuxième famille comporte dix dérivés BODIPY fusionnés de façon asymétrique en position [b]. L’aryle proximal a été modifié de façon systématique afin de mieux comprendre l’impact des substituents riches en électron et de la fusion de cycles aromatiques. De plus, ces dérivés ont été mis en relation avec une vaste série de composés analogues. Les résultats empiriques ont montré que les propriétés optoélectroniques de la plateforme sont régies par le degré de communication électronique entre l’aryle proximal, le pyrrole sur lequel il est attaché et le noyau indolique adjacent à ce dernier. Les maximums d’absorption dans le rouge sont modulables entre 547 et 628 nm et la fluorescence des composés se situe dans le proche- infrarouge. L’un des composé s’est révélé souhaitable pour une utilisation en photovoltaïque ainsi qu’à titre de sonde à pH. La troisième famille comporte cinq complexes neutres de RuII basés sur des polypyridines et portant un ligand azadipyrrométhène cyclométalé. Les composés ont montré une forte absorption de photons dans la région de 600 à 800 nm (rouge à proche- infrarouge) et qui a pu être étendue au-delà de 1100 nm dans le cas des dérivés portant un ligand terpyridine. L’analyse des propriétés optoélectroniques de façon empirique et théorique a montré un impact significatif de la cyclométalation et ouvert la voie pour leur étude en tant que photosensibilisateurs en OPV et en DSSC. La capacité d’un des complexes à photo-injecter un électron dans la bande de conduction du semi-conducteur TiO2 a été démontré en collaboration avec le groupe du Pr Gerald J. Meyer à University of North Carolina at Chapel Hill, premier pas vers une utilisation dans les cellules solaires à pigments photosensibles. La stabilité des complexes en solution s’est toutefois avérée problématique et des pistes de solutions sont suggérées basées sur les connaissances acquises dans le cadre de cette thèse. / This research project carried out in industrial collaboration with Saint-Jean Photochemicals Inc. / PCAS Canada aims at the development and characterization of dipyrromethene derivatives for photovoltaic applications. The quest for harvesting near- infrared photons was the central focus and various structural modifications were explored to improve the power conversion efficiency of organic and dye-sensitized solar cells (OPV and DSSC, respectively). Three families of chromophores which embedded a dipyrromethene motif were synthesized and characterized through spectroscopy, electrochemistry, X-ray diffraction and computationnal modelization in order to establish their structure-properties relationship. The first family includes six azadipyrromethenes with potential for tetradentate coordination on metallic centers. The development of a new asymmetric synthetic route together with the classical symmetric one allowed access to all possible combinations of derivatives including 2-hydroxyphenyl, 2-methoxyphenyl and 2-pyridyl substituents in the proximal position of the dipyrromethene. Modulation of the absorption maxima in the red ranged between 598 and 619 nm. Also, having methoxy or hydroxy substituents provided an increase of the violet absorption (~410 nm) as established by modelization. Electrochemical characterization showed that the tetradentate azadipyrromethenes were generally less stable towards redox processes as compared to their bidentate counter- parts. The second family includes ten asymmetric benzo[b]-fused BODIPYs where the proximal aryl was systematically modified in order to assess the impact of electron-rich substituents and fused aromatic cycles. The derivatives were further compared to a wide series of related BODIPYs. Empirical results showed the optoelectronic properties are dictated by the extend of electronic communication between the proximal aryl, the pyrrol to which it is attached and the adjacent indolic moiety. Absorption maxima in the red were modulated between 547 nm and 628 nm and the fluorescence was in the near-infrared. One compound proved to be a potential candidate for photovoltaic and pH probe applications. The third family includes five neutral RuII polypyridine complexes bearing a cyclometalated azadipyrromethene ligand. The compounds exhibit strong light absorption in the 600 – 800 nm range (red to near-infrared) that tails beyond 1100 nm in the terpyridine-based adducts. Analysis of the optoelectronic properties showed a significant impact of this novel cyclometalation strategy for dipyrromethene derivatives and paved the way for further incorporation of the resulting complexes as photosensitizers in OPV and DSSC. In collaboration with the group of Pr Gerald J. Meyer at the University of North Carolina at Chapel Hill, the capacity of one compound to photo-inject its electron into the conduction band of the TiO2 semiconductor was established, a first step towards their use in dye-sensitized solar cells. The structural instability in solution of the complexes hindered their full potential for photovoltaic applications and suggestions to improve them are proposed based on the knowledge acquired in the course of this thesis.