Le but de ce travail a été de développer des cellules à base d’oxyde nanoporeux photosensibilisé sur support plastique. Dans ce contexte, une nouvelle voie d’élaboration de couches de nanoparticules d’oxyde à basse température a été développée par irradiation ultraviolet sous air. Tout d’abord, des couches de dioxyde de titane ont été préparées par cette méthode, les films obtenus étant constitués d’un réseau mésoporeux de nanoparticules interconnectées de dioxyde de titane de structure anatase d’après les caractérisations effectuées par microscopie électronique à balayage, diffraction des rayons X, porosimétrie d’adsorption d’azote et d’intrusion de mercure et analyse thermogravimétrique. Après sensibilisation des couches par un complexe polypyridyle de ruthénium, les cellules photovoltaïques élaborées avec des films en contact avec un électrolyte liquide présentent des rendements de conversion énergétique compris entre 1,6 et 2,5 % suivant la nature des particules utilisées. Cette voie a ensuite été élargie à d’autres oxydes tels que l’oxyde de zinc et le dioxyde d’étain ainsi qu’à des oxydes en configuration « cœur-écorce ». Les rendements obtenus avec le dioxyde d’étain, 1,5 à 1,8%, sont tout à fait remarquables par rapport à ceux décrits dans la bibliographie pour des couches traitées à haute température. Les rendements plus élevés avec les couches traitées aux UV étant liés à une amélioration des tensions de circuit ouvert et des facteurs de forme, les phénomènes physiques régissant les performances de ces dispositifs ont été étudiés par différentes techniques, notamment la spectroscopie d’impédance électrochimique et le déclin de tension de circuit ouvert. Enfin, les performances électrochromes des films de dioxyde de titane traités aux UV ont été caractérisées sur support verre et plastique en présence d’un électrolyte liquide ionique, les efficacités de coloration étant comparables aux systèmes élaborés à haute température. / This work aimed to develop dye-sensitized solar cells on plastic substrates. In this context, a new low-temperature method to make nanoporous oxide layers based on ultraviolet irradiation under air was studied. First of all, titanium dioxide layers were prepared with this method; the films obtained were composed of a mesoporous network of interconnected anatase titanium dioxide nanoparticles as evidenced by scanning electron microscopy, X-ray diffraction, nitrogen sorption and mercury porosimetries, and thermogravimetric analysis. After sensitizing the films with a ruthenium polypyridyl complex, the photovoltaic cells based on the films in contact with a liquid electrolyte gave conversion efficiencies between 1.6 and 2.5% depending on the nature of the particles used. This low-temperature method based on ultraviolet irradiation was then expanded to other oxides, such as zinc oxide and tin dioxide, as well as to core-shell structures. The conversion efficiencies obtained with tin dioxide were very high, i.e. 1.5 to 1.8%, compared to those usually reported in the literature for films sintered at high temperatures. The higher efficiencies obtained for the UV-treated films were related to higher open circuit potentials and higher fill factors. Therefore, the physical phenomena involved were investigated with various techniques; in particular, electrochemical impedance spectroscopy and open circuit voltage decay. Finally, the electrochromic performances of the low-temperature UV-processed nanoparticulate titanium dioxide films were studied on glass and plastic substrates with an ionic liquid. The coloration efficiencies were found to be comparable to those of high-temperature processed layers.

Dye-sensitized Solar Cells (DSSC), also known as Grätzel cells, have been identified as a cost-effective, easy-to-manufacture alternative to conventional solar cells. While mimicking natural photosynthesis, they are currently the most efficient third-generation solar technology available. Among others, their cost is dominated by the synthetic dye which consists of efficient Ruthenium based complexes due to their high and wide spectral absorbance. However, the severe toxicity, sophisticated preparation techniques as well as the elevated total cost of the sensitizing dye is of concern. Consequently, the current global trend in the field focuses on the exploitation of alternative organic dyes such as natural dyes which have been studied intensively. The main attractive features of natural dyes are their availability, environmental friendly, less toxicity, less polluting and low in cost. This contribution reports on the possibility of using sepia melanin dye for such DSSC application in replacement of standard costly ruthenium dyes. The sepia melanin polymer has interesting properties such as a considerable spectral absorbance width due to the high degree of conjugation of the molecule. This polymer is capable of absorbing light quantum, both at low and high energies ranging from the infrared to the UV region. The comprehensive literature survey on Grätzel solar cells, its operating principle, as well as its sensitization by natural dyes focusing on sepia melanin has been provided in this master’s dissertation. The obtained results in investigating the morphology, chemical composition, crystalline structure as well as optical properties of sepia melanin samples using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Energy x-ray diffraction, X-ray Diffraction (XRD), Fourier Transform Infrared spectroscopy (FTIR), Raman spectroscopy, UV-VIS absorption spectroscopy as well as Photoluminescence (PL) for Grätzel solar cell application have been reported. These results represent an important step forward in defining the structure of melanin. The results clearly show that sepia melanin can be used as natural dye to DSSC sensitization. It is promising for the realization of high cell performance, low-cost production, and non-toxicity. It should be emphasized here that natural dyes from food are better for human health than synthetic dyes. / Physics / 1 online resource (xii, 101 leaves) : illustrations / M. Sc. (Physics)

An abundance of energy in our environment exists in the form of light, thermal, mechanical (e.g., vibration, sonic waves, wind, and hydraulic), magnetic, chemical, and biological. Harvesting these forms of energy is of critical importance for solving long-term energy needs and the sustainable development of the planet. However, conversion cells for harvesting solar energy and mechanical energy are usually independent entities that are designed and built following distinct physical principles. The effective and complementary use of such energy resources whenever and wherever one or all of them are available demands the development of innovative approaches for the conjunctional harvesting of multiple types of energy using an integrated structure/material. By combining solar and mechanical energy-harvesting modules into a single package for higher energy conversion efficiency and a more effective energy recovery process, the research has designed and demonstrated a hybrid cell for harvesting solar and mechanical energy. The results of the research show that we can fully utilize the energy available from our living environment by developing a technology that harvests multiple forms of both solar and mechanical energy 24 hours a day. As the proposed research represents a breakthrough in the innovation of energy harvesting, it should pave the way toward building a new field called "multi-type hybrid" energy harvesting.

High quality ammonium oxofluorotitanate discoid crystal is successfully grown on glass with an aqueous solution of ammonium hexafluorotitanate and boric acid at the molar ratio of 0.6. The concentration of hydrofluoric acid is less on the glass substrate surface and enhances the ammonium oxofluorotitanate nucleation growth. The growth rate is much higher than that grown on dioctadecyldimethylammonium. From the examinations of X-ray diffraction and high-resolution transmission electron microscopy, the crystal shows high crystalline quality and uniformity. Each titanium oxide octahedral is linked with fluorine and nitrogen atoms. Therefore, ammonium oxofluorotitanate has high potential to be thermally decomposed into high crystalline fluorine and nitrogen co-doped titanium oxide. A simple process for the preparation of nanocrystalline anatase phase titanium oxide converted from ammonium oxofluorotitanate by thermal treatment was developed. The nanocrystalline anatase phase titanium oxide shows a large bandgap reduction due to the co-doping of high concentrations of fluorine and nitrogen. Due to the excellent nanocrystalline quality and the co-doping of higher concentrations of fluorine and nitrogen at the thermal treatment temperature of 800 OC, it is 1.3 times the photocatalytic activities of P-25 due to the visble region usage of Hg lamp light source. The 11.2 times the visible photocatalytic activities of P-25 using blue light-emitting diode as the light source is obtained from thermal treatment temperature of 600 OC. There is one to one correspondence between carrier lifetime and photocatalytic activity. As a result, a highly reactive and visible-light-driven photocatalysis is achieved. The heterostructure of zinc selenide/titanium oxide and zinc sulfide/titanium oxide were prepared by metal-organic chemical vapor deposition on the above-prepared titanium oxide. The energy bandgap of zinc sulfide is much larger than that of titanium oxide and can act as a window for titanium oxide. It would not hinder titanium oxide absorption and preserve the role of fluorine and nitrogen co-doping. The energy bandgap of zinc selenide is near the maximum intensity of solar spectrum and acts as a sensitizer of titanium oxide. The lifetime of electron and hole pairs of heterostructure are about 240 and 207 nsec, which are longer than 65 nsec of titanium oxide prepared at 800 oC thermal treatment. Their photocatalytic activities are further improved to 2.0 and 1.5 times higher than that of commercial P-25. The photocatalysis of titanium oxide is very sensitive to the surface states. Titanium oxide surface defects can act as trapping sites for photo-induced holes and facilitate the separation of photo-induced carriers. Zinc selenide and zinc sulfide can passivate the surface well. It may say that titanium oxide surface defects removal has a negative impact. The density, height, diameter, PL wavelength and intensity of zinc selenide self-assembled quantum dots grown on zinc sulfide/gallium arsenide with the zinc sulfide thickness from 15 to 160 nm are studied. For a fixed 30 sec zinc selenide self-assembled quantum dots growth, it cannot be formed with the zinc sulfide thickness below 15 nm due to the close lattice match between zinc sulfide and gallium arsenide. The zinc sulfide/gallium arsenide is fully lattice relaxed with the zinc sulfide thickness higher than 130 nm examined by X-ray diffraction. The higher quality and density of zinc selenide self-assembled quantum dots can be obtained on zinc sulfide/gallium arsenide with the zinc sulfide thickness far beyond its critical thickness. The maximum zinc selenide self-assembled quantum dots density of 4.9 x 109 cm-2 with the strongest photoluminescence intensity is obtained at the zinc sulfide/gallium arsenide thickness of 130 nm. Clusters are formed on the surface of zinc selenide/gallium arsenide. The selenium segregation is the main mechanism for the formation of clusters. The dislocations will enhance the selenium segregation. Higher zinc selenide cluster corresponds to higher density of dislocations. The non-spherical cluster is formed from the mergence of the two clusters. High quality zinc oxide rods and zinc hydroxide slices are successfully grown on gallium arsenide with the aqueous solution of zinc nitrate and hexamethylenetetramine. The growth can be controlled by the appropriate nitric acid concentration incorporation in the solution. After thermal annealing, the zinc oxide slices transformed from zinc hydroxide slices can contribute much higher photocatalytic activity to 1.2 times to P-25.

Le développement des énergies renouvelables est aujourd’hui devenu un enjeu mondial majeur comme alternative aux énergies fossiles dans la production d'énergie. Parmi elles, l’énergie solaire est considérée comme la source la plus prometteuse, permettant de couvrir l’ensemble des besoins énergétiques liés à l’activité humaine. Les cellules photovoltaïques les plus performantes aujourd’hui, entre 16 et 18 % en modules, sont composées de silicium, un semi-conducteur inorganique. Cependant, leur coût de production élevé a nécessité le développement de matériaux alternatifs moins couteux. Parmi les voies explorées, les cellules solaires organiques ont émergé comme une alternative prometteuse pour produire l’électricité à faible coût. Le sujet de cette thèse s’intègre dans ce contexte de recherche. Deux types de cellules solaires ont été étudiés : les cellules à hétérojonction en volume (BHJ) et sensibilisées au colorant (DSSCs). Le courant photogénéré repose généralement (i) dans les cellules BHJ, sur le transfert entre de charge entre un polymère donneur et un accepteur d’électrons (fullerène), tels que le couple poly(3-hexyl)thiophène (P3HT) et [6,6]-phényl-C61-butanoate de méthyle (PCBM), et (ii) dans les DSSCs, la sensibilisation de la surface d’un semi-conducteur inorganique tel que l’oxyde de titane par un colorant et la présence d’un électrolyte, jouant le rôle de médiateur redox. Bien qu’ayant atteint des rendements de photoconversion respectifs de 5 et 13 %, ces cellules nécessitent des améliorations pour une commercialisation à grande échelle. Tout d’abord, les performances des cellules BHJ à base de P3HT sont considérablement limitées par sa faible absorption, ne couvrant pas la globalité du spectre solaire. Afin de palier ce problème, nous avons combiné le P3HT avec des chromophores, i.e. des porphyrines, ayant une absorption plus étendue. Ensuite, pour assurer une meilleure extraction des charges au sein du dispositif, une couche interfaciale cathodique à base de polyélectrolytes pi-conjugués a été ajoutée. Enfin, des colorants extraits de la biomasse ont été préparés afin de remplacer les colorants coûteux à base de ruthénium. En outre, les électrolytes liquides étant volatils et corrosifs, ce qui limite considérablement la stabilité des DSSCs, des électrolytes solides à base de polymères ont été étudiés comme alternative. / Among renewable energies, the sunlight has by far the highest theoretical potential to meet the worldwide need in energy. Photovoltaic devices are thus currently the subject of intense research for low-cost conversion of sunlight into electrical power. In particular, organic photovoltaics have emerged as an interesting alternative to produce electricity due to their low manufacturing cost compared to silicon solar cells, their mechanical flexibility and the versatility of the possible chemical structures. In this dissertation, we focused our research on the development of new organic pi-conjugated materials for organic solar cells applications. Two types of solar cells have been studied during this work: bulk heterojunction and dye-sensitized solar cells. The charge transfer leading to the photocurrent is usually based on (i) a polymer donor and a fullerene acceptor in BHJ solar cells, such as the widely studied poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) materials and (ii) a metal oxide (titanium oxide) sensitized with a dye and an electrolyte in DSSCs. Despite power conversion efficiencies have reached 5 and 13 % respectively for these two types of devices, they still display several drawbacks that limit their commercialization. P3HT displays a narrow absorption of the solar spectrum thus limiting the conversion efficiency. To overcome this limitation, we combined P3HT with chromophores, i.e. porphyrins, having an extending absorption. Then, to ensure better charge transfer and extraction within the device, a cathode interfacial layer based on cationic pi-conjugated polyelectrolytes was added. Finally, dyes extracted from the biomass (chlorophyll a derivatives) were synthesized to replace the expensive ruthenium dyes in DSSCs. Since liquid electrolytes are volatile and corrosive, which considerably limit the DSSCs stability, solid polymer electrolytes were also developed as an alternative.

The perceived battery capacity of battery-powered devices can be increased by harvesting energy from readily available sources. Third generation solar cells are a good candidate for this purpose since they can be integrated with these battery-powered devices and harvest power from diffused light. For a single third generation solar cell to be useful in the context of charging a Lithium based battery, the voltage must be increased tenfold. To increase this perceived battery capacity as much as possible, efficiency is crucial. In this thesis, DCDC converter topologies and designs are studied from a system design perspective. The specifications of a converter suitable for interfacing Dye-Sensitised Solar Cells with Lithium batteries are described and a market research is conducted based on those specifications. A comparison of the available commercial solutions is presented, highlighting the most suitable options. However, none of the commercial solutions met the specifications to the full extent. The design process of two DC-DC converters is presented, one is a Boost converter operating in Continuous Conduction Mode and the other is a Boost converter operating in Discontinuous Conduction Mode. A comparison of the two designs highlights the advantages of operating the Boost converter in Discontinuous Conduction Mode when interfaced with a Dye-Sensitised Solar Cell. The design with a Boost converter operating in Discontinuous Conduction Mode has an efficiency of 80.3 % and is capable of tracking the Maximum Power Point of the Dye-Sensitised Solar Cell. / Den uppfattade batterikapaciteten hos batteridrivna enheter kan ökas genom att skörda energi från lättillgängliga källor. Tredje generationens solceller är en bra kandidat för detta ändamål eftersom de kan integreras med dessa batteridrivna enheter och skörda ström från spritt ljus. För att en enda tredje generationens solcell ska vara användbar i samband med laddning av ett litiumbaserat batteri måste spänningen ökas tiofaldigt. För att öka denna uppfattade batterikapacitet så mycket som möjligt är effektiviteten avgörande. I denna avhandling studeras topologier och strategier för DC-DC-omvandlare från ett systemdesignperspektiv. Specifikationerna för en omvandlare som är lämplig för att ansluta Dye-sensitized solceller med litiumbatterier beskrivs och en marknadsundersökning utförs utifrån dessa specifikationer. En jämförelse av de tillgängliga kommersiella lösningarna presenteras och belyser de lämpligaste alternativen. Ingen av de kommersiella lösningarna uppfyllde emellertid specifikationerna i sin helhet. Designprocessen för två DC-DComvandlare presenteras, en Boost-omvandlare som arbetar i kontinuerligt ledande läge och en Boost-omvandlare som arbetar i diskontinuerligt ledande läge. En jämförelse av de två designerna belyser fördelarna med att driva Boost-omvandlaren i diskontinuerligt ledningsläge när den kopplats till en färgkänslig solcell. Konstruktionen med en Boostomvandlare som arbetar i diskontinuerlig ledningsläge har en effektivitet på 80.3 % och kan spåra den maximala effektpunkten för solcellen.

Dye-sensitized solar cells (DSC) have attracted considerable scientific and industrial interest during the past decade as an economically feasible alternative to conventional photovoltaic devices. DSCs have the potential to be as efficient as silicon solar cells, but at a fraction of the cost of silicon solar cells. The unique advantage of DSC compared to conventional solar cells is that the light absorption, electron transport and hole transport are handled by different components which reduces the chance of recombination. In the present work, to facilitate DSC with good energy conversion efficiency, its performance have been evaluated as a function of titania layer morphology, redox couple concentration and the catalytic layer on the counter electrode. The results that are obtained in the present investigations have been organized as follows Chapter 1 gives a brief exposure to DSC technology. Special emphasize has been on the structure and individual components of the DSC. Chapter 2 describes various experimental techniques that are employed to fabricate and characterize DSCs under study. Chapter 3 presents a systematic study of the characteristics of DSC made of three different types of electrodes namely: TiO2 nanotubes (TNT) which have excellent electron transport properties, TiO2 microspheres (TMS) which possess high surface area and light scattering ability and TiO2 nano particles (TNP) possessing high surface area. The electronic, morphological, optical and surface properties of individual electrodes are studied. The highest efficiency of 8.03% is obtained for DSCs prepared with TMS electrodes. A higher value of effective diffusion coefficient (Deff) and diffusion length (Ln) of electrons as obtained by electrochemical impedance spectroscopy (EIS) analysis confirms a high charge collection efficiency in microsphere based cell. Chapter 4 gives a detailed study of DSCs fabricated with a tri-layer photo anode with TNTs as light scattering layer. The tri-layer structure has given an enhanced efficiency of 7.15% which is 16% higher than TNP based cell and 40% higher than TNT based cells. Chapter 5 deals with the investigations on the effect of concentration of redox couple on the photovoltaic properties of DSC for different ratios of [I2] to [LiI] (1:2, 1:5 and 1:10) with five viii concentrations of I2 namely 0.01 M, 0.03 M, 0.05 M, 0.08 M and 0.1M in acetonitrile. It is found that the open circuit potential (Voc) decreases with increase in the ratio of redox couple whereas short circuit current density (Jsc) and fill factor (FF) increase. The reason for the decline in Voc is the higher recombination between electrons in the conduction band of TiO2 and the I3- ions present in the electrolyte, induced by the absorptive Li+ ions. In addition using EIS it is found that the τ improves with the increase in [LiI] at a particular [I2], whereas at a fixed [I2]/ [LiI] ratio the increase in [I2] is found to reduce the τ and Deff due to the enhanced recombination. Chapter 6 describes the application of carbon based counter electrode (CE) materials for DSCs. Two counter electrode materials have been investigated namely (1) Multiwalled carbon nanotubes (MWCNT) synthesized by pyrolysis method and (2) Platinum decorated multiwalled carbon nanotubes (Pt/MWCNT) prepared by chemical reduction of platinum precursors. Using Pt/MWCNT composite electrode the DSC achieved an energy conversion efficiency of 6.5 %. From the analysis on symmetric cells, it is found that electro catalytic activity of Pt/MWCNT CE is similar to that of platinum CE, though the platinum loading is very less for the former. This is attributed to the effective utilization of catalyst owing to high surface area arising from the increased surface roughness. Chapter 7 discusses the application of titanium foil in place of glass substrate for the photo anode. The titanium foil offers fabrication of flexible DSC. The performance of DSC with TMS layers and aligned titania nanotube arrays (TNA) prepared by anodization method is studied. Compared to TMS based cell, TNA has given a better efficiency at a lower thickness. Chapter 8 presents the scheme used to seal DSCs and its stability analysis. We have employed the usual hot melt sealing for edge whereas hole sealing is carried out with tooth pick and a UV curable adhesive. The degradation in efficiency is found to be 20% for low efficiency cells whereas, for high efficiency cells it is found to be 45% after 45 days. The leakage of highly volatile acetonitrile through the edge and hole is found to be responsible for the reduction in the performance of the device. Hence a high temperature sealing method is proposed to fabricate stable cells. Chapter 9 gives summary and conclusions of the present work

This work investigates the correlation of structural and photovoltaic properties of dyes used in dye-sensitized solar cells. Experimental methods, including ultraviolet-visible spectroscopy, fluorescence spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy are employed to study optical and electrochemical properties of dye molecules. Computational methods, including density functional theory and time-dependent density functional theory, are used to validate and predict the optical and electronic properties of dye molecules, in their isolated state and once embedded into a working electrode device environment that comprises a dye...TiO2 interface. The results chapters begin with the presentation of a series of quinodimethene dyes that are experimentally validated for their photovoltaic application, and associated computational studies reveal that an inner structural factor - a phenyl ring rotation occurring during the optical excitation process - leads to the competitive photovoltaic device performance of these dyes. Carbazole-based dyes are then systematically studied by computation, especially considering charge transfer paths and binding modes of these dyes on a titania surface. The theoretical models for the basic building block of this chemical family of dyes, known as MK-44, successfully support and explain structural discoveries from X-ray diffraction and reflectometry that impact of their function. A benzothiadiazole-based dye, RK-1, is then systematically studied by both experimental and computational methods, and the results show that the π-bridge composed of thiophene, benzothiadiazole and benzene rings leads to excellent charge separation; and the rotation of these rings during the optical excitation process may well be consistent with the fluorescence spectrum. Finally, the well-known ruthenium-based dyes are theoretically studied to determine the properties of different ligands connected to the metal core of the complex. Conformations with different NCS ligands are calculated in terms of energy and explain well the corresponding results from X-ray diffraction. Acid-base properties of carboxyl groups connected to pyridine ligands in N3 and N749 are theoretically calculated based on thermodynamics and density functional theory. Implicit and explicit models are both adopted to predict these acid dissociative constant values, which are generally in a good agreement with the reported experimental data. The thesis concludes with conclusions and a future outlook.

1 Abstract Diamond is a unique material for its physical and chemical stability. However, many advance applications rely on surface functionalisation. Here, two types of diamond were modified on the surface - thin layer of chemical vapor deposition (CVD) and nanodiamond particles (NDs) high pressure and high temperature (HPHT). The aim of CVD surface modification was to prepare photosensitised, conductive, diamond electrodes for dye sensitized solar cells (DSSC). For this purpose, a thin diamond layer doped with boron was deposited on the silicon wafer. Boron doping provided p-type (semi)conductivity to diamonds. The surface of the diamond was hydrogenated with H-plasma, and a short carbon linker with a protected amino group was UV-photografted to the surface. In another study, a photoconverting dye (P1) was covalently attached to the amine-linker. Furthermore, a dye designed based on donor-π-acceptor (D-π-A) concepts was attached to the surface. Finally, a systematic study was done for differently conductive diamond layer and the underlying silicon wafer These experiments gradually lead to the highest ever reported photocurrents of 6.6 µA cm2 for a flat photosensitised boron-doped-diamond (BDD) electrode. Monomolecular layer surface functionalizations on CVD diamond are difficult to detect or even quantify...