Biomaterials employed for neural stimulation, as well as brain/machine interfaces, offer great perspectives to combat neurodegenerative diseases, while application of lab-on-a-chip devices such as multielectrode arrays is a promising alternative to assess neural function in vitro. For bioelectronic monitoring, nanostructured microelectrodes are required, which exhibit an increased surface area where the detection sensitivity is not reduced by the self-impedance of the electrode. In our study, we investigated the interaction of neurons (SH-SY5Y) and glial cells (U-87 MG) with nanocolumnar titanium nitride (TiN) electrode materials in comparison to TiN with larger surface grains, gold, and indium tin oxide (ITO) substrates. Glial cells showed an enhanced proliferation on TiN materials; however, these cells spread evenly distributed over all the substrate surfaces. By contrast, neurons proliferated fastest on nanocolumnar TiN and formed large cell agglomerations. We implemented a radial autocorrelation function of cellular positions combined with various clustering algorithms. These combined analyses allowed us to quantify the largest cluster on nanocolumnar TiN; however, on ITO and gold, neurons spread more homogeneously across the substrates. As SH-SY5Y cells tend to grow in clusters under physiologic conditions, our study proves nanocolumnar TiN as a potential bioactive material candidate for the application of microelectrodes in contact with neurons. To this end, the employed K-means clustering algorithm together with radial autocorrelation analysis is a valuable tool to quantify cell-surface interaction and cell organization to evaluate biomaterials’ performance in vitro

Lithium-ion battery is attractive for various applications because of its high energy density. The performance of Li-ion battery is influenced by several properties of the electrode materials such as particle size, surface area, ionic and electronic conductivity, etc. Porosity is another important property of the electrode material, which influences the performance. Pores can allow the electrolyte to creep inside the particles and also facilitate volume expansion/contraction arising from intercalation/deintercalation of Li+ ions. Additionally, the rate capability and cycle-life can be enhanced. The following porous electrode materials are investigated. Poorly crystalline porous -MnO2 is synthesized by hydrothermal route from a neutral aqueous solution of KMnO4 at 180 oC and the reaction time of 24 h. On heating, there is a decrease in BET surface area and also a change in morphology from nanopetals to clusters of nanorods. As prepared MnO2 delivers a high discharge specific capacity of 275 mAh g-1 at a specific current of 40 mA g-1 (C/5 rate). Lithium rich manganese oxide (Li2MnO3) is prepared by reverse microemulsion method employing Pluronic acid (P123) as a soft template. It has a well crystalline structure with a broadly distributed mesoporosity but low surface area. However, the sample gains surface area with narrowly distributed mesoporosity and also electrochemical activity after treating in 4 M H2SO4. A discharge capacity of about 160 mAh g-1 is obtained at a discharge current of 30 mA g-1. When the acid-treated sample is heated at 300 °C, the resulting porous sample with a large surface area and dual porosity provides a discharge capacity of 240 mAh g-1 at a discharge current density of 30 mA g-1. Solid solutions of Li2MnO3 and LiMO2 (M=Mn, Ni, Co, Fe and their composites) are more attractive positive electrode materials because of its high capacity >200 mAh g-1.The solid solutions are prepared by microemulsion and polymer template route, which results in porous products. All the solid solution samples exhibit high discharge capacities with high rate capability. Porous flower-like α-Fe2O3 nanostructures is synthesized by ethylene glycol mediated iron alkoxide as an intermediate and heated at different temperatures from 300 to 700 oC. The α-Fe2O3 samples possess porosity with high surface area and deliver discharge capacity values of 1063, 1168, 1183, 1152 and 968 mAh g-1 at a specific current of 50 mA g-1 when prepared at 300, 400, 500, 600 and 700 oC, respectively. Partially exfoliated and reduced graphene oxide (PE-RGO) is prepared by thermal exfoliation of graphite oxide (GO) under normal air atmosphere at 200-500 oC. Discharge capacity values of 771, 832, 1074 and 823 mAh g -1 are obtained with current density of 30 mA g-1 at 1st cycle for PE-RGO samples prepared at 200, 300, 400 and 500 oC, respectively. The electrochemical performance improves on increasing of exfoliation temperature, which is attributed to an increase in surface area. The high rate capability is attributed to porous nature of the material. Results of these studies are presented and discussed in the thesis.

Les travaux réalisés dans cette thèse ont porté sur la synthèse d’oxydes de manganèse et leur association dans des composites avec des matériaux carbonés (NTC, Graphène), pour une utilisation comme matériaux d’électrodes de supercondensateurs fonctionnant en milieux aqueux. Les caractérisations physico-chimiques et électrochimiques ont été menées sur ces matériaux afin d’évaluer leurs performances et étudier l’effet de la nanostructuration. Il s’est avéré que la réalisation de nanocomposites MnO2/ nanotubes de carbone ou MnO2/ oxydes de graphène réduits contribue à l’amélioration des performances électrochimiques. Plusieurs compositions Mn/C ont été étudiées afin de réaliser un matériau d’électrode de supercondensateur optimisé. Des dispositifs asymétriques en milieux aqueux ont été assemblés associant les meilleurs nanocomposites avec une électrode négative de graphène. De nettes améliorations en termes de densités d’énergie et de puissance ont été obtenues sur ces systèmes asymétriques fonctionnant sur 2 volts en milieux aqueux. / The work realized in this thesis focused on the synthesis of manganese oxides and their assembly in composites with carbon materials (CNT, graphene) for supercapacitor applications in aqueous media. Physico-chemical and electrochemical characterizations were conducted to evaluate the effect of the nanostruturation. It was found that nanocomposites MnO2/CNT and MnO2/ reduced graphene oxide contributed to improve the electrochemical performances in aqueous media. Several compositions Mn/C were tested to estimate the best ratio for optimized electrode materials. In order to maximize the energy of the devices, asymmetric devices in aqueous media were assembled using graphene as negative electrode and nanocomposites for positive. Clear improvements in term of energy and power densities were obtained with these systems working at 2 volts in aqueous media.

Rechargeable Li-ion batteries and supercapacitors are the most promising electrochemical energy storage devices in terms of energy density and power density, respectively. Recently, nanostructured materials have gained enormous interest in the field of energy technology as they have special properties compared to the bulk. Commercially available Li-ion batteries, which are the most advanced among the rechargeable batteries, utilize microcrystalline transition metal oxides as cathode materials which act as lithium insertion hosts. To explore better electrochemical performance the use of nanomaterials instead of conventional materials would be an excellent alternative. High Li-ion insertion at high discharge rates causes slow Li+ transport which in turn results in concentration polarization of lithium ions within the electrode material, causing a drop in cell voltage. This eventually, leads in termination of the discharge process before realizing the maximum capacity of the electrode material being used. This problem can be addressed by decreasing the average particle size which leads to an increase in surface area of the electrode material. Nanostructured materials, because of their high surface area and large surface to volume ratio, to some extent can overcome the problem of slow diffusion of ions. Supercapacitors are electrical energy storage devices which can deliver large energy in a short time. A supercapacitor can be used as an auxiliary energy device along with a primary source such as a battery or a fuel cell to achieve power enhancement in short pulse applications. Active materials for supercapacitors are classified into three categories: (i) carbonaceous materials, (ii) conducting polymers and (iii) metal oxides. Among the materials studied over the years, metal oxides have been considered as attractive electrode materials for supercapacitors due to the following merits: variable oxidation state, good chemical and electrochemical stability, ease of preparation and handling. The performance of supercapacitors can be enhanced by moving from bulk to nanostructured materials. The theme of the thesis is to explore novel routes to synthesize nanostructured materials for Li-ion batteries and supercapacitors, and to investigate their physical and electrochemical characteristics. Chapter I is an introduction of various types of electrochemical energy systems such as battery, fuel cell and supercapacitor. A brief review is made on electrode materials for Li-ion batteries and supercapacitors, and nanostructured materials. Chapter II deals with the study of nanostrip orthorhombic V2O5 synthesized by a two-step procedure, with the formation of a vanadyl ethylene glycolate precursor and post-calcination treatment. The precursor and the final product are characterized for phase and composition by powder X-ray diffraction (XRD), infrared (IR) spectroscopy, thermal analysis (TGA) and X-ray photoelectron spectroscopy (XPS). The morphological changes are investigated using field emission scanning electron microscopy (FE-SEM) and high resolution transmission electron microscopy (HRTEM). It is found that the individual strips have the following dimensions, length: 1.3 μm, width: 332 nm and thickness: 45 nm. The electrochemical lithium intercalation and de-intercalation of nanostrip V2O5 is investigated by cyclic voltammetry (CV), galvanostatic charge-discharge cycling, galvanostatic intermittent titration technique (GITT) and electrochemical impedance spectroscopy. Chapter III describes the synthesis of nanoparticels of LiMn2O4 by microwave assisted hydrothermal method. The phase and purity of spinel LiMn2O4 are confirmed by powder XRD analysis. The morphological studies are carried out using FE-SEM and HRTEM. The electrochemical performance of spinel LiMn2O4 is studied by using CV and galvanostatic charge-discharge cycling. The initial discharge capacity is found to be about 89 mAh g-1 at a current density of 21 mA g-1 with reasonably good cyclability. Chapter IV deals with synthesis of MoO2 nanoparticles through ethylene glycol medium and its electrochemical characterization. XRD data confirms the formation MoO2 on monoclinic phase, space group P21/c. Polygon shape of MoO2 is observed in HRTEM. MoO2 facilitates reversible insertion-extraction of Li+ ions between 0.25 to 3.0 V vs. Li/Li+. CV and galvanostatic charge-discharge cycling are conducted on this anode material to complement the electrochemical data. Chapter V reports the synthesis of nanostructured MnO2 at ambient conditions by reduction of potassium permanganate with aniline. Physical characterization is carried out to identify the phase and morphology. The as prepared MnO2 is amorphous and it contains particles of 5 to 10 nm in diameter. On annealing at a temperature > 400 °C, the amorphous MnO2 attains crystalline α-phase with a concomitant change in morphology. A gradual conversion of nanoparticles to nanorods (length 500-750 nm and diameter 50-100 nm) is evident from SEM and TEM studies. High resolution TEM images suggest that nanoparticles and nanorods grow in different crystallographic planes. The electrochemical lithium intercalation and de-intercalation of nanorods was performed by (CV) and galvanostatic charge-discharge cycling. The initial discharge capacity of nanorod α-MnO2 is found to be about 197 mAh g-1 at a current density of 13.0 mA g-1. Capacitance behavior of amorphous MnO2 is studied by CV and galvanostatic charge-discharge cycling in a potential range from -0.2 to 1.0 V vs. SCE in 0.1 M sodium sulphate solution. The effect of annealing on specific capacitance is also investigated. Specific capacitance of about 250 F g-1 is obtained for as prepared MnO2 at a current density of 0.5 mA cm-2 (0.8 A g-1). Chapter VI pertains to electrochemical supercapacitor studies on nanostructured MnO2 synthesized by polyol method. Although X-ray diffraction (XRD) pattern of the as synthesized nano-MnO2 shows poor crystallinity, it is found that it is locally arranged in δ-MnO2 type layered structure composed of edge-shared network of MnO6 octahedra by Mn K-edge X-ray Absorption Near Edge Structure (XANES) measurement. Annealed MnO2 shows high crystalline tunneled based α-MnO2 as confirmed by powder XRD pattern and XANES. As synthesized MnO2 exhibits good cyclability as an electrode material for supercapacitor. In Chapter VII, capacitance behavior of nanostrip V2O5, TiO2 coated V2O5 and nanocomposites of PEDOT/V2O5 are presented. Structural and morphological studies are carried out by powder XRD, IR, TGA, SEM and TEM. Cyclic voltammogram of pristine V2O5 shows the regular rectangular shape indicating the ideal capacitance behavior in aqueous 0.1 M K2SO4. The SC value of pristine V2O5 is found to be about 100 F g-1. Nanostrip V2O5 is modified with TiO2 using titanium isobutoxide to enhance the capacitance retention upon cycling. Only 48 % of the initial capacitance remains in the case of pristine V2O5 after 100 cycles, while TiO2 coated V2O5 exhibits better cyclability with capacitance of 70 % of the initial capacitance. The capacitance retention is attributed to the presence of TiO2 on the surface of V2O5 which prevents the vanadium dissolution into the electrolyte. Microwave assisted hydrothermally synthesized PEDOT/V2O5 nanocomposites are utilized as capacitor materials. The initial SC of PEDOT/V2O5 (237 F g-1) is higher than that of either pristine V2O5 or PEDOT. The enhanced electrochemical performance is attributed to synergic effect and an enhanced bi-dimensionality. Details of the above studies are described in the thesis with a conclusion at the end of each Chapter.

Emerging energy storage applications are driving the demand for Li-ion battery positive electrode materials with higher energy densities and lower costs. The recent production of complete pseudo-ternary phase diagrams of the Li-Mn-Ni-O system generated using combinatorial methods has provided a greater understanding of the impact of initial composition, synthesis temperature, and cooling rate on the phases that form in the final materials. This thesis focuses on the synthesis and characterization of gram-scale positive electrode materials in the Li-Mn-Ni-O system. Structural analysis of these samples has resulted in the production of partial pseudo-ternary phase diagrams focusing on the positive electrode materials region of the Li-Mn-Ni-O system at 800°C and 900°C in air for both quenched and slow cooled compositions. These bulk-scale diagrams support the observations of the combinatorial diagrams, and show similar layered and cubic structures contained within several single- and multi-phase regions. The phases that form at each composition are shown to be dependent on both the reaction temperature and cooling rate used during synthesis. The electrochemical characterization of two composition series near Li2MnO3, one quenched and one slow cooled, is presented. The quenched compositions exhibited reversible cycling at 4.4 V, voltage plateaus and small increases in capacity above 4.6 V, and large first cycle irreversible capacity losses at 4.8 V. In the slow cooled series, all but one composition exhibited initial capacities below 100 mAh/g which began to continually increase with cycling, with several compositions exhibiting capacity increases of 300% over 150 cycles at 4.9 V. In both series, analysis of the voltage and differential capacity plots indicated that significant structure rearrangements are taking place in these materials during extended cycling, the possible origins of which are discussed. Finally, high precision coulometry studies of one Li-deficient and two Li-rich single-phase layered compositions are discussed. These materials exhibit minimal oxidation of simple carbonate-based electrolyte when cycled to high potential, with the Li-deficient composition producing less electrolyte oxidation at 4.6 V vs. Li/Li+ than commercial Li[Ni1/3Mn1/3Co1/3]O2 at 4.2 V. The inherent inertness of this composition may make it suitable for use as a thin protective layer in a core-shell particle.

Les travaux de cette thèse ont porté sur l'élaboration, l'optimisation et l'étude d'électrodes composites de nanotubes de carbone verticalement alignés (VACNT) sur un collecteur d'aluminium et modifiés par l'oxyde de manganèse (MnO₂). Les VACNT synthétisés par voir CVD à basse température (580°C:) directement sur le collecteur ont permis d'obtenir des tapis de NTC parfaitement alignés d'une épaisseur allant de 20 à 80 µm et possédant des densités de 10¹¹ NTC.cm² et dont le taux de catalyseur (Fe) est inférieur à 1%. Leur modification par du MnO2 permet d’accroître leur capacité de stockage électrochimique. Afin de réaliser un enrobage optimal des VACNT par le MnO₂, différents précurseurs de l'oxyde ainsi que diverses méthodes(dépôts électrochimiques, chimiques, CVD) ont été utilisées et optimisées. Les composites élaborés ont ensuite été étudiées en tant que matériau d'électrode pour la réalisation de supercondensateurs asymétriques eu milieux aqueux. / This thesis was focused on the development, optimization and study of composite electrodes of vertically aligned carbon nanotubes (VACNT) on an aluminum collector and modified with manganese oxide (MnO₂).VACNT were synthesized by a CVD process at low temperature (580° C) directly on the collector. Perfectly aligned CNT forest with a thickness of 20 to 80 μm were obtained with high densities of 10¹¹ NTC.cm² and whose catalyst (Fe) content is less than 1%. Their modification with MnO₂ increase their electrochemical storage capacity. In order to achiew optimal coating of VACNT by MnO₂, different precursors of the oxide and various methods ( electrochemical, chemical, CVD) were used and optimized. Composites were studied as electrode material for the realization of asymmetric supercapacitors in aqueous media. In addition, structurals, morphologicals and electrochemicals analyzes carried out on the different materials allowed a better understanding of the role of the elaboration's conditions on the properties of the VACNT/MnO₂ composites obtained.