This dissertation investigates the control of the electrical energy input to a three-phase electric arc furnace (EAF). Graphite electrodes are used to convert electrical energy into heat via three-phase electric arcs. Constant arc length is desirable as it implies steady energy transfer from the graphite electrodes to the metallic charge in the furnace bath. With the charge level constantly changing, the electrodes must be able to adjust for the arc length to remain constant. In this dissertation electric arc current is used as the control variable. This is the most often used control variable in the electric arc furnace industry and implies fast adjustments of short circuits between the electrode tips and the metallic charge. The motivation behind the modelling of the electrode system for a three-phase electric arc furnace is to extend an existing EAF model developed at the University of Pretoria. The existing model investigates the control of the electric arc furnace process itself and it is assumed that the applied electrical energy input is constant. Proportional-Integral-Derivative (PID) control as well as Model-Predictive-Control (MPC) is applied to the electrode system. Time delays on the outputs of the hydraulic actuators makes it necessary to include approximations of time delays on the outputs of the linear model, which is needed for controller design. A well known general control problem is followed in this dissertation. All models are derived from first principles, and complete controller design is carried out. Most available literature lack in at least one of these fields. / Dissertation (MEng (Electronic Engineering))--University of Pretoria, 2007. / Electrical, Electronic and Computer Engineering / unrestricted

This dissertation investigates the heterogeneous electron transfer dynamics and electrocatalytic behaviour of the following molecules immobilized on gold electrode: (a) 2-dimethylaminoethanethiol (DMAET), with and without integration with poly (m-aminobenzenesulfonic acid) functionalised single-walled carbon nanotubes (SWCNT-PABS); (b) SWCNT-PABS and iron (II) phthalocyanine nanoparticles (nanoFePc); (c) Colloidal gold / Gold nanoparticles (AuNP) and nanoFePc (d) ; water-soluble iron (II) tetrasulfophtalocyanine (FeTSPc) and SWCNT-PABS, and (e) novel monolayer protected gold nanoparticles (MPCAuNPs) by means of either (i) layer-by-layer (LBL) self-assembly or (ii) self-assembled monolayer (SAM) fabrication strategy. Atomic force microscopy and electrochemical studies (cyclic voltammetry, and electrochemical impedance spectroscopic) were used to monitor the substrate build-up, via strong electrostatic interaction. The surface pKa of DMAET was estimated at 7.6, smaller than its solution pKa of 10.8. It is also shown that SWCNT-PABS is irreversibly attached to the DMAET SAM. For layered films involving SWCNT-PABS and nanoFePc (Au-DMAET- SWCNT-PABS-nanoFePc) n (n=1-5 layers) as the number of bilayers increase, the electron transfer kinetics of the [Fe(CN) 6]3-/4 redox probe decreases. On the contrary, LBL assembly involving AuNP and nanoFePc (Au-DMAET-AuNP-nanoFePc) n (n=1-4 layers) shows an increase followed by a decrease in electron transfer kinetics subsequent to the adsorption of nanoFePc and AuNP layers, respectively. For SAMs involving FeTSPc and SWCNT-PABS, the mixed hybrid (Au-DMAET-SWCNT-PABS/FeTSPc) exhibited fastest charge transport compared to other electrodes. For the novel MPCAuNPs, the protecting or stabilizing ligands investigated were the (1-sulfanylundec-11-yl) tetraethylene glycol (PEG-OH) and the (1-sulfanylundec-11-yl) polyethylene glycolic acid (PEG-COOH). Three different mass percent ratios (PEG-COOH : PEG-OH), viz. 1:99 (MPCAuNP-COOH1%), 50:50 (MPCAuNP-COOH50%) and 99:1 (MPCAuNP-COOH99%) were used to protect the gold nanoparticles. The impact of these different ratios on the electron transfer dynamics in organic and aqueous media was explored. The average electron transfer rate constants (ket / s-1) in organic medium decreased as the concentration of the surface-exposed –COOH group in the protecting monolayer ligand increased: MPCAuNP-COOH1% (~ 10 s-1) > MPCAuNP-COOH50% (~ 9 s-1) > MPCAuNP-COOH99% (~ 1 s-1). In aqueous medium, the trend is reversed. This behaviour has been interpreted in terms of the hydrophobicity (quasi-solid nature) and hydrophilicity (quasi-liquid nature) of the terminal –OH and –COOH head groups, respectively. The ionization constants of the terminal groups (i.e., surface pKa) was estimated as ~ 8.2 for the MPCAuNP-COOH1%, while both MPCAuNP-COOH50% and MPCAuNP-COOH99% showed two pKa values of about 5.0 and ~ 8.0, further confirming the hydrophilicity / hydrophobicity of these surface functional groups. Hydrogen peroxide (H2O2), epinephrine (EP) and ascorbic acid (AA) were used as model analytes to examine electrocatalytic ability of these nanostructured assemblies. The electrochemical reduction of H2O2 at a constant concentration was amplified upon increasing bilayer formation of SWCNT-PABS and nanoFePc, while SWCNT-PABS/FeTSPc showed the best response towards the detection of epinephrine. MPCAuNP-COOH99% showed an excellent suppression of the voltammetric response of the AA and an enhanced electrocatalytic activity towards the detection of EP compared to the other MPCAuNPs. / Thesis (PhD)--University of Pretoria, 2010. / Chemistry / unrestricted

The main goals in electroanalytical sensing are towards improved sensitivity and selectivity, or specificity, of an analyte. There are several approaches to achieving these goals with the main approach being modification of an electrode surface with synthetic or natural catalysts (enzymes), polymers and also utilisation of nanostructured materials. At present, there is a strong movement towards hybrid sensing which couple different properties of two or more surface modification approaches. In this thesis, a range of these surface modifications were explored for analysis and detection of two main analytes: the amino acid, tryptophan (Trp); and, the neurotransmitter, dopamine (DA). Specifically, this thesis aimed to utilise these methods to enhance the sensitivity and selectivity for Trp over an interferent, the indoleamine, melatonin (Mel); and, DA over the vitamin, ascorbic acid (AA). For Trp detection, immobilisation of an enzyme, Tryptophanase (Trpase) resulted in poor selectivity for the analyte. However, enhanced sensitivity and selectivity was achieved through pH manipulation of the electrolyte medium at a Nafion®-modified electrode surface for both Trp and Mel. At pH 3.0, the Mel and Trp anodic peak potentials were sufficiently resolved allowing for an LOD of 1.60 and 1.62 nM,respectively, and permitting the accurate analysis of Trp in a dietary supplement containing Mel. Multi-walled carbon nanotubes (MWCNTs) suspended in Nafion® exhibited further increases in the signal responses of these analytes at pH 3.0 and 7.4 with minimal change in the resolution of the anodic peaks. A lower sensitivity was, therefore, observed at the Nafion® and MWCNT modified electrode compared to the Nafion®-modified electrode at pH 3.0 with LODs of 0.59 and 0.80 nM exhibited for Trp and Mel, respectively. Enhanced selectivity for Trp in the presence of Mel can be achieved with MWCNTs in the presence of metallotetrasulphonated phthalocyanines (MTSPcs) particularly at pH 3.0, owing to cation exchange effects. However, the lack of sensitivity towards Trp, and even Mel, at this CoTSPc and MWCNT modified electrode remains a drawback. For DA, detection at the MWCNT and Nafion® surface resulted in improved sensitivity over that of both the bare electrode (613.0 nM) and the Nafion® modified electrode (1045.1 nM) with a calculated LOD of 133.9 nM at this layer. Furthermore, improvements in the selectivity of DA were achieved at the Nafion® and MWCNT modified electrode as exclusion of AA (150 μM) was achieved. At the MWCNT and CoTSPc surface, AA was excluded up to 130 μM with sensitivity for DA extending as low as 14.3 nM, far greater than observed for Trp and Mel. These concentrations are well within physiological concentration ranges and represent the most significant solution yet in terms of AA exclusion and enhanced sensitivity for DA. An examination of the surface layering by impedance spectroscopy and atomic force microscopy indicates that the success of the hybrid sensor utilising CoTSPc and MWCNTs lay in improved dispersion of MWCNTs and improved electron transfer kinetics, facilitated by the net charge of the materials present. This thesis, thus, showed the utility of a judicious selection of synthetic and biological catalysts, polymers and carbon nanomaterials towards a hybrid approach to the electrochemical sensing of Trp, Mel, DA and AA with focus on sensitivity and selectivity of these analytes.

No description available.

Women are four to eight times more likely to injure their anterior cruciate ligament (ACL) compared to men. It is most commonly injured through a non-contact mechanism during game time situations. During landings, women display valgus collapse, where a less active gluteus medius muscle (GMed) may be unable to control the internal rotation of the thigh, causing an increase in knee joint abduction angle, augmenting the risk of ACL injury. This study’s purpose was to determine the difference between 12 male and 12 female athletes in muscle activity, specifically the GMed, and the 3D kinematics and kinetics of the lower-limb during drop jump landings from three heights; maximum vertical jump height, tibial length, and a commonly used height of 40cm. Results showed that females had greater hip adduction and knee abduction angles compared to men. The GMed activity showed no significant differences between sexes at each drop jump height.

Ph.D. (Chemistry) / In this study, carbon based electrode materials such as glassy carbon, graphene, diamond and exfoliated graphite were explored as suitable electrode materials for electrochemical detection, electrochemical and photoelectrochemical degradation of organic water pollutants. Graphene modified glassy carbon electrode sensor was developed for bisphenol A. Cyclic voltammetry was used to study the electrochemical properties of the prepared graphene- modified glassy carbon electrode using potassium ferricyanide as a redox probe. The prepared graphene- modified glassy carbon electrode exhibited more facile electron kinetics and enhanced current of about 75% when compared to the unmodified glassy carbon electrode...

Zinc oxide and graphene nanostructures are important technological materials because of their unique properties and potential applications in future generation of electronic and sensing devices. This dissertation investigates a brief account of the strategies to grow zinc oxide nanostructures (thin film and nanowire) and graphene, and their applications as enhanced field effect transistors, chemical sensors and transparent flexible electrodes. Nanostructured zinc oxide (ZnO) and low-gallium doped zinc oxide (GZO) thin films were synthesized by a magnetron sputtering process. Zinc oxide nanowires (ZNWs) were grown by a chemical vapor deposition method. Field effect transistors (FETs) of ZnO and GZO thin films and ZNWs were fabricated by standard photo and electron beam lithography processes. Electrical characteristics of these devices were investigated by nondestructive surface cleaning, ultraviolet irradiation treatment at high temperature and under vacuum. GZO thin film transistors showed a mobility of ~5.7 cm 2/ V•s at low operation voltage of ~0.5 V with a sub threshold swing of ~85 mV/decade. Bottom gated FET fabricated from ZNWs exhibit a very high on-to-off ratio (~10 6) and mobility (∼28 cm 2 /V•s). A bottom gated FET showed large hysteresis of ~5.0 to 8.0 V which was significantly reduced to ~1.0 V by the surface treatment process. The results demonstrate charge transport in ZnO nanostructures strongly depends on its surface environmental conditions and can be explained by formation of depletion layer at the surface by various surface states. A nitric oxide (NO) gas sensor using single ZNW, functionalized with Cr nanoparticles was developed. The sensor exhibited average sensitivity of ~46% and a minimum detection limit of ~1.5 ppm for NO gas. The sensor also is selective towards NO gas as demonstrated by a cross sensitivity test with N2, CO and CO2 gases. Graphene film on copper foil was synthesized by chemical vapor deposition method. A hot press lamination process was developed for transferring graphene film to flexible polymer substrate. The graphene/polymer film exhibited a high quality, flexible transparent conductive structure with unique electrical-mechanical properties; ~88.80 % light transmittance and ~1.1742 kΩ/sq sheet resistance. The application of a graphene/polymer film as a flexible and transparent electrode for field emission displays was demonstrated.

O estudo de polímeros condutores desperta um enorme interesse científico e tecnológico devido às diversas aplicações possíveis para esses materiais, como o desenvolvimento de dispositivos eletro-eletrônicos e sensores. Através de processos de dopagem esses polímeros tornam-se eletroativos, possibilitando por meio de técnicas eletroquímicas a determinação de diversas substâncias. Na agropecuária, a utilização intensiva e crescente de produtos químicos como pesticidas e fertilizantes, tem provocado diversas contaminações e agressões, despertando interesse na utilização de sensores para o monitoramento dessas substâncias em tempo real. Os eletrodos modificados com polímeros condutores têm-se apresentado como uma alternativa devido a algumas peculiaridades como alta estabilidade física e química e excelentes possibilidades analíticas devido à versatilidade da polimerização eletroquímica. Este trabalho teve como objetivo o desenvolvimento de novos materiais de eletrodos modificados com polímeros condutores para a determinação eletroanalítica de pesticidas. Os pesticidas estudados foram os herbicidas 2,4-D, bentazon, glifosato, paraquat e o inseticida paration metílico. Foram realizadas medidas voltamétricas e de impedância com eletrodos de carbono vítreo, pasta de carbono e eletrodos modificados com polianilina e polipirrol, visando a obtenção de sensores para a detecção destes pesticidas. Estudos de interação dos pesticidas com os polímeros foram realizados utilizando-se a técnica de espectrofotometria de UV-visível para a determinação da concentração dos pesticidas em estudos cinéticos. Também utilizou-se a espectroscopia de impedância eletroquímica para auxiliar no entendimento das interações entre os pesticidas e os polímeros condutores. Adicionalmente foi aplicada uma metodologia de análise de fluxo descontínuo (BIA), utilizada com sucesso na determinação de metais, para a determinação de pesticidas. Os resultados mostraram uma seletividade nas interações entre os polímeros condutores e os pesticidas. Por meio da resposta voltamétrica dos polímeros condutores, os eletrodos de pasta modificados com polianilina e polipirrol mostraram-se hábeis na detecção dos pesticidas não eletroativos como o 2,4-D, o bentazon e o glifosato, bem como na determinação do paraquat. Estes resultados atribuem aos eletrodos modificados desenvolvidos neste trabalho a característica de sensores de diagnóstico da presença destes pesticidas em solução. A metodologia de BIA na determinação de pesticidas, apresentou inúmeras vantagens do ponto de vista analítico, como a não renovação da superfície de eletrodo, micro-volumes de injeção de amostra, dezenas de análise sem troca do eletrólito suporte, tempos de análise inferiores a um segundo bem como a possibilidade de utilização de dispositivo portátil para análises em campo. / Studies of conducting polymers have great technological and scientific interest due to many possibilities of applications like the development of electronic devices and sensors. By means of a doping process these polymers became electroactives, allowing the determination of substances that specifically interact with the polymers. In agriculture the intensive and constant use of chemical substances as pesticides and fertilizers are causing several environmental contamination and the development of sensors for real time analysis has been a research field of intense interest. Electrodes modified with conducting polymers have several interesting characteristics as their high physical and chemical stability and excellent analytical possibilities, due to the versatility of the electrochemical polymerization. The objective of the present work was the development of electrode materials modified with conducting polymers for the electroanalytical determination of pesticides. The pesticides studied were the herbicide 2,4-D, bentazon, gliphosate and paraquat and the insecticide methylparathion. Voltammetric measurements were performed on glassy carbon and carbon paste electrodes modified with polianiline and polipirrol to obtain a procedure for the pesticides measurement. Studies of interaction between the pesticides and the polymers were performed using UV-visible spectrophotometry for pesticide concentration determination kinetic sorption experiments and the electrochemical impedance technique was also used to evaluate such sorption processes. Batch Injection Analysis (BIA), a technique successfully used for the analysis of metals, was also tested for the determination of the herbicide paraquat. Results obtained from the kinetic studies and the voltammetric and impedance experiments showed some selectivity for the interaction of the pesticide with the two polymers. By means of the voltammetric response of the polymers, the carbon paste electrode modified with polianiline showed to be very suitable for the detection of the herbicide 2,4-D, bentazon and gliphosate, but not for paraquat and methilparathion. On the other hand the carbon paste electrode modified with polipirrol detect only the gliphosate and paraquat. The results shows that the detection of the paraquat and the gliphosate by the polipirrol are not influenced by protonation, whereas the detection of the 2,4-D, bentazon and gliphosate by the polianiline are due to sorption and consequent doping of the polymer by the pesticides, which have acidic behavior. The BIA technique used for the detection of the pesticide paraquat, showed a good sensitivity and could be used in the future for the analysis of such substances with many advantages when compared with conventional electroanalytical procedures.

This thesis first uses physical scale models to investigate solid-state phenomena - surface layer formation, solid-state diffusion of lithium, electrochemical reactions at the solid-electrolyte interface, as well as homogeneous chemical phase change reactions. Evidence is provided that surface layer formation on the magnetite, Fe3O4, electrode can accurately be described mathematically as a nucleation and growth process. To emulate the electrochemical results of the LiV3O8 electrode, a novel method is developed to capture the phase change process; this method describes phase change as a nucleation and growth process. The physical parameters of the LiV3O8 electrode: the solid-state diffusion coefficient, phase change saturation concentration, phase reaction rate constant, and exchange current density, are all quantified and the agreement with experimental results is compelling. Electrochemical evidence, corroborated by results from density functional theory, indicate that delithiation is a more facile process than lithiation in the LiV3O8 electrode. Further investigation of the LiV3O8 electrode is undertaken by coupling the crystal scale model to electrode scale phenomena. Characterization of the LiV3O8 electrode by operando EDXRD experiments provides a unique and independent set of observations that validate the previously estimated physical constants for the phase change saturation concentration and phase change reaction rate constant; they are both found to be consistent with their previous estimates. Finally, it is observed that anodic physical phenomena are important during delithiation of the cathode because the kinetics at the anode become mass-transfer limited. Finally, it is illustrated that coupling physical models to data science and algorithmic computing is an effective method to accelerate model development and quantitatively guide the design of experiments.

Screen-printed carbon electrodes (SPCEs) have garnered much attention as sensors due to their simplicity and relatively low cost. However, to impart necessary selectivity and sensitivity for specific applications, modification of the SPCE surface, which can involve time-consuming procedures or costly equipment/materials, is typically required. Here, a simple nitrogen-doping process based on NH4OH was used to modify SPCEs prepared from commercially available ink for electrochemical detection of H2O2, a common target for biosensing strategies and indicator of cell stress. XPS studies showed that NH4OH treatment of SPCEs led to a nearly 5-fold increase in surface nitrogen content (from 0.28% to 1.34%). Compared to SPCEs, nitrogen-doped SPCEs (N-SPCEs) demonstrated enhanced current and lower onset potentials for H2O2 reduction. Amperometric detection of H2O2 at an applied potential of -0.4 V (vs. Ag/AgCl) using N-SPCEs also exhibited a wider linear range, lower detection limit, and higher sensitivity than SPCEs.