Master’s thesis is focused on creating a suitable methodology for determining the parameters of the electronic control unit of the engine. Discusses how the measurement of input data into the methodology, the basic description of its functions and display the resulting values. It includes evaluation of applicability of the methodologies and the real parameters when compared with the parameters established on the basis of established methodology.

The thesis focuses on a hydraulic system design for a specific application of hydrostatic drive with regard to energy efficiency of proposed solution. Standard hydraulic and electronic components are used, mostly products of Bosch Rexroth. The aim of the thesis is to carry out a complex design from mechanic through hydraulic up to the electronic part of the system. After a short introduction in the beginning of the thesis is the particular application described and analyzed. Then the elemental principles of hydraulic devices and systems are explained. In the following part the actual solution is presented, which expands to several different alternatives. These alternatives are compared according to set criteria and the selected alternative is then further developed. At the end of the thesis, the outputs are evaluated and the direction of further possible improvements in the design is outlined.

Abstract Master thesis is focused on The Application of Data from Vehicle Electronic Control Units in the Analysis of Road Accidents. The theoretical part deals with the electronic systems of vehicles and their control units, diagnostic processes, retrieving accident data from the controls unit and the need for these data in the analysis of road accidents. The experimental part focuses on obtaining data for crashed vehicles, interpretation of such data and assessment of their usefulness for analyzing road accidents. It also focuses on the procedures and methods on how to retreive accident data.

The thesis is focused on determining the methodology of engine diagnostics for vehicles with common rail direct fuel injection. The first section describes the communication between the diagnostic tools and control units, and the common rail system for diesel engines. The next section specifies the procedure for the acquisition, processing and analysis of data using selective diagnostic tools along with software in a numerical computing environment. Subsequently, from the results, the equivalent electronic control of the fuel injection quantity is established for the purpose of research, vehicle servicing. The results may also allow for additional observations to be made.

The goal of the master´s thesis is to design testing unit for small batch production. The background research part introduces testing principles, we are also discussed different ways of realization of testing connectors and choice of control unit. The work also describes the design of the hardware wiring and mechanical design. The result of this thesis is a device implemented according to the proposal described in the work. No significant fault was found during operation of testing unit, which verified its reliability and full functionality. The work also includes a description of the software implementation in Python.

Other than mobile hydraulics and high voltage switchgears, Bucher Hydraulics is also involved in the less-known area of hydraulic lifts. In fact, Bucher Hydraulics did invent the electronically controlled lift valve in the 1970s. Since then, Bucher Hydraulics developed a wide line of products for hydraulic elevators, such as valves and power units. In 2012, this valve family included various sizes, pressure ranges, systems with constant motor speeds, inverter-driven motors, energy-efficient solutions with hydraulic counterweight, as well as customized solutions. As the common principle, all these solutions apply an electronic closed-loop control that uses a volumetric flow sensor and a proportional actuator. Since 2012, Bucher Hydraulics is substituting this valve family with a new generation, the iValve. Every iValve uses several self-teaching algorithms to adapt to its environment. Their on-board and cabinet electronics control solenoid currents and measure flow, pressure, and temperature. These features enable the iValve to self-monitor, to adapt to operating parameters, and to analyze and log information about itself and the attached system. This report on a highly specialized product is meant to provide inspiring insights.

I detta examensarbete utreddes huruvida elektriska tester av styrenheter för tunga fordon kan automatiseras på befintliga testmiljöer. Arbetet utfördes på uppdrag av Scania CV AB för arbetsgruppen Electronic Hardware som utför tester vid utveckling och verifiering av krav på styrenheter. Genom en automatiserad testprocess kan testarbetet effektiviseras och kvaliteten höjas. Testarbetet sker på testriggar som innehåller fullskalig hårdvara från lastbilar för att kunna emulera styrenhetens autentiska arbetsmiljö. För att komma fram till ett testsystem som kunde leva upp till de krav och behov som formulerats inom kravprocessen i arbetet användes utvecklingsmodeller. Utvärderingsmatriser användes för att välja den mjuk- och hårdvara som skulle vara mest lämplig för det automatiserade testsystemet utifrån kraven. Resultatet visade att testsystemet skulle bestå av en testprogramvara som körs på en vanlig persondator och ett inbyggt system med elektroniska komponenter för att kunna utföra de elektriska testerna. För att demonstrera testsystemets möjligheter i ett helhetstest konstruerades en prototyp som har funktionalitet att utföra ett testfall som kan dra stor nytta av att automatiseras, nämligen att testa omslagsnivåer för en digital ingång. Prototypen baserades på ett mikrokontrollerkort från Arduino och ett kretskort konstruerades till detta för att kunna utföra elektriska tester med högre spänningsnivåer som krävs för styrenheter på Scaniafordon. För att utforma testfall och hantera testprocessen valdes LabVIEW, en programvara där tester designas med ett grafiskt programmeringsspråk. Testresultaten för prototyptestsystemet visade att verifieringen av kraven för omslagsnivåer förenklas radikalt vid ett automatiserat förfarande, eftersom testtiden kunde minskas drastiskt, i synnerhet vid ett repetitivt förfarande. / This thesis work intends to study the possibilities to automate electrical testing of electronic control units in an existing test environment. The work was executed on behalf of Scania CV AB for the department Electronic Hardware, who run tests in development and verification of requirements for electronic control units. By using an automated testing system, the testing process could be made more effective and raise the quality. The testing work is done on test rigs which are equipped with full-scale hardware from real trucks to emulate the working environment the electronic control unit operates into. Development models were used to be able to create a testing system which could meet the requirements that were defined during the requirement engineering process. Evaluation matrices were used to choose the soft- and hardware that could be considered the most appropriate for the automated testing system according to the requirements. The result shown that the testing system should consist of a testing software that runs on an ordinary computer and an embedded system equipped with electronic components to enable the testing system for electrical tests. To demonstrate the possibilities of the whole testing system a prototype was manufactured which was designed to execute a test case that could greatly benefit from the advantages that comes with automation. It was a test case set out to measure voltage levels when switching in a digital input. The prototype was based on a microcontroller card from Arduino and was joined by a printed circuit board to be able to run electrical tests with the higher voltage levels that were demanded by electronic control units. To design test cases and manage the test process, LabVIEW was chosen, a software in which tests are designed in a graphical programming language. Test results for the prototype test system showed that verification of the requirements for voltage levels when switching was radically simplified by an automated procedure, as the test time could be drastically reduced, particularly in a repetitive procedure.

As the automotive industry becomes increasingly reliant on digital systems it is of utmost importance that these systems are secure. Secure systems are of interest both for the general public as well as manufactures. This Master’s thesis evaluates potential cybersecurity solutions for a proposed damper system prototype developed by Öhlins Racing AB. A systematic literature study was performed to identify known vulnerabilities of similar systems as well as potential cybersecurity solutions. A threat model was constructed using vehicleLang, the Meta Attack Language, and securiCAD. The model was created utilizing preexisting assets from vehicleLang and a newly implemented Bluetooth asset. The result from the systematic literature study was used to validate preexisting attack steps and also to create the Bluetooth asset. To validate the model, experts in the field of automotive security and/or threat modeling were asked to assess the model. Using Cochran’s Equation, a target of eight expert evaluations were decided. Unfortunately, only seven evaluations were obtained, equivalent to an increase in the error margin from 25% to 26.6%. However, of the seven expert evaluations obtained none indicated the existence of critical flaws within the model. The model was therefore considered a good reflection of the damper system and its security aspects. Critical defenses included the utilization of cryptography, mutual authentication, and on-the-fly decryption. These defenses were shown to prevent unauthorized modifications of firmware and protect Öhlins intellectual property in form of source code. While it was not possible to defend against all attacks the identified defenses would increase the safety and security of the system, benefiting not only Öhlins but also overall road users. / Allt eftersom fordonsindustrins beroende av digitala system ökar är det av yttersta vikt att dessa system är säkra. Säkra system är av intresse för både allmänheten likväl som för systemtillverkarna. Denna masteruppsats evaluerar potentiella cybersäkerhetslösningar för en föreslagen stötdämparprototyp utvecklad av Öhlins Racing AB. En systematisk litteraturöversikt skapades med syfte att identifiera kända sårbarheter av liknande system och potentiella cybersäkerhetslösningar. En hotmodell skapades med hjälp av vehicleLang, the Meta Attack Language, och securiCAD. Hotmodellen skapades med existerande komponenter från vehicleLang och en nyskapad Bluetooth komponent. Resultaten från den systematiska litteraturöversikten användes för att validera existerande komponenter från vehicleLang och för implementationen av Bluetooth komponenten. För att evaluera modellen bads experter inom fordonssäkerhet och/eller hotmodellering utvärdera modellen. Genom Cochran’s ekvation beslutades att åtta expert utvärderingar skull införskaffas. Tyvärr erhölls enbart sju utvärderingar, vilket motsvarar en ökning av felmarginalen från 25% till 25.6%. Av de sju experter som utvärderade modellen identifierades dock inga kritiska brister. Kritiska säkerhetslösningar inkluderade användandet av: kryptografi, ömsesidig autentisering, och on-the-fly decryption. Dessa försvar anses kunna skydda mot obehörig modifiering av programvara, samt skydda Öhlins intellektuella egendom i form av källkod. Trots att det inte var möjligt att förhindra alla attacker skulle de identifierade försvaren öka systemets säkerhet, vilket är fördelaktigt inte bara för Öhlins utan även trafikanter i allmänhet.

Thesis (MSc (Physics))--University of Stellenbosch, 2006. / External cavity diode lasers are used increasingly as sources of light in applications ranging from industrial photonic systems to basic laboratory research on the interaction of light and atoms. External cavity diode lasers offer more stable output frequency and narrow spectral bandwidth than the typical free-running diode lasers. These characteristics are achieved by exploiting the sensitivity of diode lasers to external optical feedback. In this study the design and development of an external cavity diode laser system for future applications in spectroscopy and laser cooling of rubidium atoms is presented. The external cavity diode laser including mechanical components and control electronics of the system is developed from basic components. The system uses frequency selective optical feedback from a diffraction grating in a Littrow configuration to provide collimated, narrow-band, frequency tunable light near 780 nm. The external cavity diode laser is designed to increase the mode-hop-free frequency tuning range, and allow accurate frequency tuning and stabilisation. A low-noise current source and a temperature controller for thermal stability were developed as part of the system since the output frequency changes with temperature and current. The temperature controller is optimised experimentally for the thermal characteristics of the external cavity. An electronic sidelock servo circuit for frequency locking of the external cavity diode laser to an external reference for long term frequency stabilisation is proposed and discussed. The servo circuit electrically controls the grating tilt and the current through the diode laser in order to lock the frequency of the diode laser. The external cavity diode laser is optimised and characterised near 780 nm. Results obtained in this study indicate that the external cavity diode laser is suitable for future applications in spectroscopy and laser cooling of neutral rubidium atoms.

Nas últimas décadas, a indústria automobilística mundial vem investindo no desenvolvimento tecnológico dos motores, com o objetivo de alcançar melhor eficiência energética e atender às legislações que limitam a quantidade de resíduos tóxicos nos gases de exaustão e menor consumo de combustível. Isso resultou na implantação dos sistemas de gerenciamento eletrônico do motor, que possibilitam funcionalidades para se controlar diversas variáveis do motor, aumentando consideravelmente o rendimento do motor. Este trabalho tem como objetivos explorar a dinâmica de um motor de combustão interna ciclo Otto, os sinais elétricos associados, e os componentes de seu gerenciamento eletrônico. A partir dessas informações, o trabalho apresenta o processo de analise dos sinais elétricos e as estratégias de controle utilizadas em um sistema de gerenciamento real. Assim, são desenvolvidos o hardware e o firmware de uma unidade microcontroladora para gerenciamento eletrônico do motor. O hardware foi elaborado com uma concepção centralizada, ou seja, foi usado apenas um microcontrolador de 32-bit para gerenciar todas as funções. O firmware de controle foi desenvolvido de forma modular baseado em modelos de malha fechada. O modelo matemático do motor foi identificado utilizando técnicas de controle em um veículo real, e a avalidação do modelo foi obtida através de testes em um dinamômetro inercial. / In the last few decades, the world automotive industry has invested in the technological development of the engines, aiming to get better energetic efficiency and comply with legislations that limit the amount of toxic exhaustion gases. This resulted in electronic management systems for engines, which allowed flexibility to control several engine-related variables, considerably increasing the engine efficiency. This work aims to explore the Otto cycle combustion engine dynamics, its electronic signals, and the elements of its electronic management. Based on that information, this work presents the analysis process of the electronic signals, and the control strategies used in a real management system. Then, the hardware and firmware of a microcontroller unity are developed for the electronic management of the engine. The hardware was elaborated with a centralized concept, i.e., only one 32-bit microcontroller was used to control all functions. The control firmware was developed in a modular scheme, based on the closed loop models. The engine mathematical model was identified using control techniques in a real engine. The results were obtained by tests in an inertial dynamometer.