Distribution systems across most parts of the globe are highly radial in nature. As loads are gradually increased on a particular distribution system, a higher operating current state leading to increased fault current levels is attained. Hence, the relay co-ordination is disturbed and equipments such as feeders and circuit breakers need to be replaced with higher rating so that they can handle the new currents often leading to expensive retrofit costs. The use of fault current limiter (FCL) is proposed to mitigate the effects of high current levels on a distribution system. A comprehensive and up-to-date literature review of FCL technologies is presented. Detailed efforts of an in-house developed behavioral superconducting FCL model are delineated, including FCL control algorithm and its implementation in PSCAD®/EMTDC environment. Results from simulation studies are investigated and compared to an actual FCL commissioned by Z-energy to highlight the effectiveness of a generic model without having to access proprietary details. Extending those concepts, a solid-state and hybrid type of limiter is also modeled and it results discussed. Finally, an impact assessment is conducted on the distribution protection scheme, due to the FCL being inserted and subsequently operated in the distribution system. / Master of Science

Current practice in U.S. underground coal mine high-voltage distribution systems is to attempt to limit ground fault current to 25 Amperes and de-energize the circuit at 10 Amperes. However, the significant amount of system capacitance due to the use of shielded cables can cause ground fault current to be two or three times the intended ground fault limit. Consequently, this practice can cause several issues such as ground fault currents significantly exceeding the neutral grounding resistor current limit, loss of relay selectivity in the distribution system, and transient overvoltages in certain ground fault situations. These issues are solved to some extent by using a resonance grounded system, currently used in some other countries. However, a shortcoming of traditional resonance grounded systems is the inability to deal with the harmonic components existing in ground fault current. With the increasing use of nonlinear sources such as variable frequency drives, the proportion of harmonic components in ground fault current can be significant. Consequently, although the fundamental component can be almost fully compensated in a traditional resonance grounded system, the harmonic components can still be large enough to maintain arcing and cause personal injury and equipment damage. In this dissertation, a novel method is developed to perform real-time prediction of the harmonics in ground fault currents. Methods for neutralizing the ground fault current harmonics and identifying ground fault location are also developed. Results indicate that the combination of traditional high-resistance grounding and active current injection to neutralize harmonics in the ground fault has the potential to significantly reduce the total ground fault current and reduce arc and flash hazards during ground faults in high voltage distribution systems.

For effective operation of microgrid systems (MGSs), it is important to understand the major types of power grid failures and how to deal with them. Detecting the fault, locating it, and isolating the faulty line are important to avoid damaging components and interrupting the service for customers. This will also improve the reliability and protection level of the system during fault conditions. Among the most successful protection methods to limit fault currents in power systems is the fault current limiter (FCL). The FCL improves the reliability of the system, voltage stability, and the fault current reduction. However, limited researches consider its applications inMGSs. The location and impedance size of the FCL play a major role in limiting fault currents in the system. Several studies concluded that installing FCLs near all generators, transformers, or loads in the system enhanced the performance of the system during fault conditions. However, increasing the number of FCLs in the system leads to an increase in cost. This dissertation proposes several effective approaches to specify the optimal locations and impedance values of the required number of installed FCLs in a grid-connected MGS. These FCLs improve the reliability and the protection level of the system by limiting fault currents during fault conditions. The goal is to reduce the required number of installed FCLs in the system. These installed FCLs must be able to reduce fault currents under the interrupting ratings of circuit breakers in the system. This goal will lead to lower the cost of installed protection devices in the system. In order to achieve this goal, this dissertation presents a novel fault management approach, sensitivity analysis, and an optimization model to find the optimal solutions. The study of this dissertation is meant to be used during the planning stage of power distribution system design. The results of this dissertation prove the robustness of the proposed approaches. This enhances the system’s performance while minimizing the required number of installed FCLs. Their sizes limit fault currents within safe ranges. Thus, the FCL significantly improves the reliability and protection scheme of the grid-connected MGS.

No description available.

No description available.

This thesis presents the applications of a series interconnection scheme for small distributed generation (DG) systems in distribution networks. The concept uses one set of voltage source converter (VSC) to control the injected voltage magnitude and phase angle for power injection and voltage sag mitigation. Through an energy storage device and the VSC, DG outputs vary concurrently with the line loading and provide load leveling functions. Under voltage sag situations, it provides missing voltages to effectively deal with power quality problems. Due to its series connection characteristic, it is convenient in preventing islanding operation and good for fault current limiting. The concept is suitable for locations where the voltage phase shift is not a major concern. Due to the use of only one set of converter, it is economic for customer site distributed energy resource applications and its control strategy would depend on the types of load connected.

No description available.

No description available.

Kraven på ett driftsäkert elnät ökar hela tiden i takt med att elanvändning blir allt viktigare i dagens samhälle. Luftledningar byts ut med markkabel och möjlighet till reservmatningar samt bra elkvalitet är av hög prioritering. Skicket på elnätets utrustning försämras med åren och kommer med tiden behöva bytas ut. Med uppdrag från Uddevalla Energi AB har siffror tagits fram berörande spänningsfall, kapacitiv jordfelsström och belastningar vid normaldrift och reservmatning, samt ålder och typ på kablar i Uddevalla citys mellanspänningsnät. Den här rapporten presenterar dessa resultat och ger några förslag på ändringar om så krävs. Även en del om planerade framtida utbyggnationer tas upp och hur dessa påverkar nätet. För att få fram resultaten används Uddevalla Energis program för nätberäkning, "DpPower". Beräkningarna visade att vid normaldrift var alla värden godkända enligt tumregler som Uddevalla Energi följer. Vid reservmatning däremot var vissa linjer överbelastade, analysen visar dock tillgängliga lösningar. Ålder och status på kablar i nätet varierar stort vilket gör det svårt att specificera hur ombyggnationer ska ske. Hänsyn bör istället tas till överbelastningar. / The demand of reliable power distribution is increasing as the usage of power is increasing in the society of today. Overhead lines are replaced by underground cables, availability to reserve power supply and power quality is of high priority. The condition of the equipment deteriorates over the years and will eventually have to be replaced. By request from Uddevalla Energi, values have been provided concerning voltage drop, capacitive ground fault current and loads during normal operation and standby power supply. The types and ages of cables in Uddevalla City’s high-voltage network has also been looked at. This report presents these results and gives some suggestions for modifications if required. Planned future deployments are looked over and how these may affect the network. To obtain these results the network calculating program "DpPower" was used. The calculations presented shows that in normal operation all values are approved within the company standards that Uddevalla Energi follows. For the reserve supply however, some lines are overloaded. The analysis shows possible solutions for these issues. Age and status of cables in the network varies widely, making it difficult to specify how redevelopments should take place. Instead the overloads should be given more consideration.

abstract: This dissertation presents a new hybrid fault current limiter (FCL) topology that is primarily intended to protect single-phase power equipment. It can however be extended to protect three phase systems but would need three devices to protect each individual phase. In comparison against the existing fault current limiter technology, the salient fea-tures of the proposed topology are: a) provides variable impedance that provides a 50% reduction in prospective fault current; b) near instantaneous response time which is with-in the first half cycle (1-4 ms); c) the use of semiconductor switches as the commutating switch which produces reduced leakage current, reduced losses, improved reliability, and a faster switch time (ns-µs); d) zero losses in steady-state operation; e) use of a Neodym-ium (NdFeB) permanent magnet as the limiting impedance which reduces size, cost, weight, eliminates DC biasing and cooling costs; f) use of Pulse Width Modulation (PWM) to control the magnitude of the fault current to a user's desired level. g) experi-mental test system is developed and tested to prove the concepts of the proposed FCL. This dissertation presents the proposed topology and its working principle backed up with numerical verifications, simulation results, and hardware implementation results. Conclu-sions and future work are also presented. / Dissertation/Thesis / Ph.D. Electrical Engineering 2013