<p> With the increasing demand for data rate and transmission distance, the trend in fiber-optic communications is to build an ultra-high, long-haul transmission system. One of the challenges in this kind of systems comes from the fiber dispersion and dispersion slope. For the wide-band wavelength-division multiplexing (WDM) system or ultra-high bit rate optical time-division multiplexing (OTDM) system, the dispersion slope could be a serious problem to impair the system performance.</p> <p> Many studies have shown that the dispersion and dispersion slope affect the long-haul fiber transmission dramatically, especially for the high-capacity systems. Most of them recommend to totally compensate the dispersion and the dispersion slope simultaneously. And a lot of compensating techniques are proposed. However, it is not easy to realize the simultaneous compensation for the dispersion and dispersion slope in the practical systems. Therefore, the necessity of compensating the dispersion slope in wide-bandwidth systems should be verified.</p> <p> We focus on the study of ultra-high bit rate (160-Gb/s) single-channel fiber-optic transmission. The results show that the dispersion slope is not necessary for the dispersion-managed system when the optimal launch parameters are given. Then we present how to find out the optimum in fiber-optic systems and a novel optimizing technology, space mapping technology (SM) is introduced, which has been successfully applied to the electromagnetic area. An application of SM in optical systems is implemented. By using this smart optimization technique, lots of computational efforts for evaluating the fine model in optimization process are saved.</p> / Thesis / Master of Applied Science (MASc)

This thesis studies spatial and temporal filtering techniques and their applications in fiber optic communication systems. Differential mode delay (DMD) in multimode fibers (MMFs) and multipath interference (MPI) are two major impairments in fiber optic communication systems. DMD lends to inter symbol interference in MMF communication systems which seriously limit the bit rate-distance product of the system. MPI leads to interference pattern at the output of a single mode fiber link which increases the bit error rate of the system. In this thesis, we propose a method which uses spatial filtering technique in a 4F system to reduce DMD and MPI effects. Typically, higher order modes have higher spatial frequency components and therefore, they are spatially separated from the lower mode after Fourier transform. By optimizing the bandwidth of a spatial filter, unwanted higher order modes can be suppressed. Therefore, DMD and MPI effects in fiber optic communication systems can be reduced at the cost of losing some fraction of the signal power. In this thesis, we also propose a new application of temporal filtering technique. A time lens is a phase modulator which introduces a quadratic phase factor in time domain. Combined with single mode fibers, a time lens can be used to perform Fourier transform in time domain. A tunable optical filter can be implemented using a modified temporal 4F system which is analogy with the spatial 4F system. The merit of this method is that no additional signal processing is needed to reverse the bit sequence at the output of the 4F system and that the channels to be demultiplexed at a node can be dynamically reconfigured. / Thesis / Master of Applied Science (MASc)

The bandwidth requirements for global communication networks are increasing each year due to the rapid growth of multimedia (broadband) applications. To accommodate this growth, an increasing number of wide-area and local-area networks are converting the transmission medium from copper wire to fiber. As such, the deployment of optical fiber communication systems for emerging high-speed networks (10 - 40 gigabits-per-second) mandates integrated and low-cost designs for optical transceivers. CMOS, with its low-cost, system-on-chip, and mixed-signal capabilities, is a suitable alternative to other more expensive technologies, such as silicon germanium or gallium arsenide. On the other hand, limitations of sub-micron CMOS technology, namely the higher parasitic capacitances, higher noise, and low-quality integrated passive elements, make the design of an integrated optical transceiver in CMOS technology a challenging task. The design, fabrication and characterization of a broadband transimpedance amplifier in an analog front-end of an optical receiver will be presented in this thesis. The chip was designed and fabricated using a TSMC 0.18 (mu)m CMOS technology. It was measured and characterized, achieving a -3dB bandwidth of 1.5 GHz and 37 dB(omega) of transimpedance gain, with less than -7 dB input and output reflections to a 50 (omega) measurement interface, while consuming 23.8 mW from a 1.8 V supply and using 1 x 0.781 mm^2 of silicon chip area. The strengths and limitations of this design will be discussed and its performance will be compared to published results. Conclusions will be drawn and recommendations will be proposed to demonstrate the utility of this design in future work on fully integrated optical receiver systems. Next, an optical transmitter prototype circuit, built by using low-cost, off-the-shelf photonic and microelectronic components, was fabricated and tested in order to assess the performance of directly modulated lasers for use in low-cost multi-gigabit-per-second optical transmitter modules. The performance of the transmitter was assessed for a fiber link spanning 10 km of standard single-mode optical fiber. This work illustrates how the non-idealities and imperfections of low-cost components can significantly degrade the overall system performance in high-speed applications; therefore, recommendations will be proposed so as to improve the performance in spite of these limitations. / Thesis / Master of Applied Science (MASc)

Since the introduction of optical fibers in 1960's in communication systems, researchers have encountered many challenges to improve the signal quality at the receiver as well as transmitting the signal as distant as possible. The former was achieved by employing coherent receivers, which let us use M-array modulation formats, such as QPSK, or QAM, and polarization of the signal. The later is accomplished by the advent of optical amplifiers. Optical amplifiers enable us to compensate for the loss occurred within the fiber optic line, without the need for optical-electrical signal conversion. These amplifiers add noise to the line which interacts with the nonlinearity in the fiber line. This interaction causes phase change in the propagating signal called nonlinear phase noise, which degrades the system performance. In this study we will derive an analytical expression for the linear and nonlinear phase noise variance in dispersion unmanaged fiber optic systems, using a first-order perturbation theory. We use numerical examples to depict the proposed system performance in terms of nonlinear phase noise variance. We will conclude that the nonlinear phase variance in a dispersion unmanaged system is much lower than the corresponding noise variance in a dispersion managed system. We will use this concept and will introduce more dispersion in the line by adding fiber brag gratings (FBGs) throughout the fiber link. Through numerical simulations, we will illustrate the improvement we get by adding FBG in each span. We will show that employing FBG improves the system performance for systems working at symbol rates 5 GBaud, which we get the best improvement to less than 20 GBaud, and beyond 20 GBaud there will be no improvement. Nowadays, telecommunication systems based on fiber optics are working at symbol rates around 28 GBaud. We will introduce new models to reduce the nonlinear phase, by splitting digital back propagation (DBP) between transmitter and receiver, and using optical phase conjugation (OPC) in the line. We will prove that the new proposed models lower the phase noise variance significantly, for single pulses. We will also illustrate numerical examples to validate the betterment they provide in terms of Q-factor. / Thesis / Master of Applied Science (MASc)

This dissertation addresses several theoretical issues in low-finesse fiber optic Fabry-Perot Interferometric (FPI) sensors. The work is divided into two levels: modeling of the sensors, and signal processing based on White-Light-Interferometry (WLI). In the first chapter, the technical background of the low-finesse FPI sensor is briefly reviewed and the problems to be solved are highlighted. A model for low finesse Extrinsic FPI (EFPI) is developed in Chapter 2. The theory is experimentally proven using both single-mode and multimode fiber based EFPIs. The fringe visibility and the additional phase in the spectrum are found to be strongly influenced by the optical path difference (OPD), the output spatial power distribution and the working wavelength; however they are not directly related to the light coherence. In Chapter 3, the Single-Multi-Single-mode Intrinsic FPI (SMS-IFPI) is theoretically and experimentally studied. Reflectivity, cavity refocusing, and the additional phase in the sensor spectrum are modeled. The multiplexing capacity of the sensor is dramatically increased by promoting light refocusing. Similar to EFPIs, wave-front distortion generates an additional phase in the interference spectrogram. The resultant non-constant phase plays an important role in causing abrupt jumps in the demodulated OPD. WLI-based signal processing of the low-finesse FP sensor is studied in Chapter 4. The lower bounds of the OPD estimation are calculated, the bounds are applied to evaluate OPD demodulation algorithms. Two types of algorithms (TYPE I & II) are studied and compared. The TYPE I estimations suffice if the requirement for resolution is relatively low. TYPE II estimation has dramatically reduced error, however, at the expense of potential demodulation jumps. If the additional phase is reliably dependent on OPD, it can be calibrated to minimize the occurrence of such jumps. In Chapter 5, the work is summarized and suggestions for future studies are given. / Ph. D.

The purpose of this study is to characterize the plasma spray deposits used for attaching intrinsic Fabry-Perot interferometric fiber optic strain sensors. The deposits must maintain adhesion at elevated temperatures without distorting the sensors' signals. Two different material systems were tested and modeled, a nickel based alloy and yttria-stabilized zirconia. The material properties of the deposits and the thermal stresses in the system were evaluated to determine attachment lifetime of the sensors. The encapsulated sensors' signals were collected before and after plasma spraying and at elevated temperatures. The material properties of the deposits were evaluated by electron microscopy, energy dispersive x-ray spectroscopy, scratch testing, thermal fatigue testing, and nanoindentation. The thermal stresses were evaluated by Raman spectroscopy and from finite element analysis in COMSOL® Multiphysics®. Several of the sensors broke during encapsulation due to the plasma spray processing conditions and the signals experienced distortion at elevated temperatures. The sensors can be treated to remove this interference to allow for this deposit attachment. The nickel based alloy's ductility and lamellar microstructure allowed for non catastrophic relaxation mechanisms to relieve induced thermal stresses. The yttria stabilized zirconia failed catastrophically at elevated temperatures due its lack of compliance to mismatches in thermal expansion. A high melting point metallic deposit, similar to the nickel based alloy, is desirable for fiber optic sensor attachment due to its ductility, thermal expansion, and dominant relaxation mechanisms. The processing conditions may need to be optimized to allow for the sensors' protection during encapsulation. / Master of Science

In this thesis, the optical communication systems for millimeter-scale sensing and communication devises known as "Smart Dust" are described and analyzed. A smart dust element is a self-contained sensing and communication system that can be combined into roughly a cubic-millimeter mote to perform integrated, massively distributed sensor networks. The suitable passive optical and fiber-optic communication systems will be selected for the further performance design and analysis based on the requirements for implementing these systems. Based on the communication link designs of the free-space passive optical and fiber-optic communication systems, the simulations for link performance will be performed. / Master of Science

A majority of underground coal mine disasters in the United States are due to explosions. Current atmospheric monitoring system (AMS) practices in the US could be enhanced to facilitate data sharing and learning of the entire work force. With the inclusion of additional atmospheric monitoring and data collecting, meaningful analysis can be realized and shared with the workforce. AMS data can be utilized to advance the understanding of underground atmospheres for the entire workforce along with adding to the knowledge base for preventative planning. An AMS interface ADAMAS is suggested to facilitate this conglomeration and sharing of the data visually, so that it can be quickly processed and applied in their daily decisions. An emerging sensor technology for underground mining, fiber optics is explored and tested in emergency, or fire and explosion situations. The fiber optic methane sensor performed well in smoke only showing a slow in response time due to soot on the filter. The ADAMAS interface was tested in a large population of underground coal miners. The population varied in age, job, classification, and experience. They all primarily found it to be easy to use and helpful to them. Concerns arose when asked how this will facilitate an improved relationship with regulatory agencies. There is trepidation when it comes to additional atmospheric information sharing, that it may not be used advance understanding of mine atmospheres. The AMS data collected is individual to each mine site but can assist in the understanding of underground atmosphere as a whole. Moving forward, regulatory bodies should use this as a stepping point to consider how this information can be used to advance the field of mine ventilation and also the health and safety of the miner. / Ph. D.

Gas Sensing Has Become a Very Important and Attractive Technique Because of Its Various Applications, Such as in the Increasingly Concerning Case of Environmental Issues, Automobile Emission Detection, Natural Gas Leakage Detection, Etc. It Also Has Significant Applications in Industries, Such as Safety and Health Monitoring in Underground Mines. Among Those Sensing Areas, Fiber-optic Sensors Have Drawn Considerable Attention Because of Its Small Size, Light Weight, High Sensitivity, and Remote Sensing Capability. However, Current Fiber-optic Gas Sensing Techniques Have Several Limitations on Their Potential for Multiplexed or Distributed Sensing Due to Difficulties Such as High Complexity or Large Loss. To Accomplish the Goal for Multiplexed Gas Sensing, an Off-centered Core Fiber Design Is Investigated. The Eccentric Core Can Reduce Attenuation, Keep Mechanical Strength, and Lower Fabrication Cost. To Verify the Feasibility of the Design, Fiber Field Distribution Is First Studied in Simulation, Which Will Be Discussed in Detail in Chapter 2. Then Two Fiber Samples with a Length of 10 Cm and 40 Cm Are Prepared and Placed in a Custom Methane Sensing System for Gas Absorption Testing, Which Is Detailed in Chapter 3. From Etching Analysis, Localized Surface Defects Are Found as the Main Reason for Power Loss. Performance Such as Detection Resolution and Sensitivity Are Investigated. In Chapter 4, Theoretical Evaluations Have Been Conducted for Multiplexed Sensors Performances Using the Off-centered Core Fiber to Study the Impact Fiber Parameters on Sensing System Design. The Conclusion and Summary Are Presented in Chapter 5. / Master of Science / Gas Sensing Has Become a Very Important and Attractive Technique Because of Its Various Applications, Such as in the Increasingly Concerning Case of Environmental Issues, Automobile Emission Detection, Natural Gas Leakage Detection, Etc. It Also Has Significant Applications in Industries, Such as Safety and Health Monitoring in Underground Mines. Among Those Sensing Areas, Fiber-optic Sensors Have Drawn Considerable Attention Because of Its Small Size, Light Weight, High Sensitivity, and Remote Sensing Capability. However, Current Fiber-optic Gas Sensing Techniques Have Several Limitations on Their Potential for Long Distance Distributed Sensing Due to Difficulties Such as High Fabrication Complexity. In This Work, a Fiber-optic Gas Sensor with Special Structure Was Designed. The Sensor Can Reduce Attenuation, Keep Mechanical Strength, and Lower Fabrication Cost. To Verify the Feasibility of the Design, Theory Analysis and Simulation Were Conducted, Which Will Be Discussed in Detail in Chapter 2. Then Two Samples with a Length of 10 Cm and 40 Cm Were Prepared and Placed in a Custom Methane Sensing System for Testing. And Their Performance Such as Sensitivity Is Investigated. In Chapter 4, Theoretical Evaluations Have Been Conducted for Multiplexed Sensors Performances Evaluation to Study the Impact Fiber Parameters on Sensing System Design. The Conclusion and Summary Are Presented in Chapter 5.

DNA detection technology has developed rapidly due to its extensive application in clinical diagnostics, bioengineering, environmental monitoring, and food science areas. Currently developed methods such as surface Plasmon resonance (SPR) methods, fluorescent dye labeled methods and electrochemical methods, usually have the problems of bulky size, high equipment cost and time-consuming algorithms, so limiting their application for in vivo detection. In this work, an intrinsic Fabry-Perot interferometric (IFPI) based DNA sensor is presented with the intrinsic advantages of small size, low cost and corrosion-tolerance. This sensor has experimentally demonstrated its high sensitivity and selectivity. In theory, DNA detection is realized by interrogating the sensor's optical cavity length variation resulting from hybridization event. First, a microgap structure based IFPI sensor is fabricated with simple etching and splicing technology. Subsequently, considering the sugar phosphate backbone of DNA, layer-by-layer electrostatic self-assembly technique is adopted to attach the single strand capture DNA to the sensor endface. When the target DNA strand binds to the single-stranded DNA successfully, the optical cavity length of sensor will be increased. Finally, by demodulating the sensor spectrum, DNA hybridization event can be judged qualitatively. This sensor can realize DNA detection without attached label, which save the experiment expense and time. Also the hybridization detection is finished within a few minutes. This quick response feature makes it more attractive in diagnose application. Since the sensitivity and specificity are the most widely used statistics to describe a diagnostic test, so these characteristics are used to evaluate this biosensor. Experimental results demonstrate that this sensor has a sensitivity of 6nmol/ml and can identify a 2 bp mismatch. Since this sensor is optical fiber based, it has robust structure and small size ( 125μm ). If extra etching process is applied to the sensor, the size can be further reduced. This promises the sensor potential application of in-cell detection. Further investigation can be focused on the nanofabrication of this DNA sensor, and this is very meaningful topic not only for diagnostic test but also in many other applications such as food industry, environment monitoring. / Master of Science