Doctor of Philosophy / Department of Civil Engineering / Hayder Rasheed / Recent applications in reinforced concrete columns, including strengthening and extreme loading events, necessitate the development of specialized nonlinear analysis methods to predict the confined interaction domain of axial force, shear, and bending moment in square and slightly rectangular concrete columns. Fiber-reinforced polymer (FRP) materials are commonly used in strengthening applications due to their superior properties such as high strength-to-weight ratio, high energy absorption and excellent corrosion resistance. FRP wrapping of concrete columns is done to enhance the ultimate strength due to the confinement effect, which is normally induced by steel ties. The existence of the two confinement systems changes the nature of the problem. Existing research focused on a single confinement system. Also, very limited research on rectangular sections was found in the literature. In this research, a model to estimate the combined behavior of the two systems in rectangular columns is proposed. The calculation of the effective lateral pressure is based on Lam and Teng model and Mander model for FRP wraps and steel ties, respectively. The proposed model introduces load eccentricity as a parameter that affects the compression zone size, and in turn the level of confinement engagement. Full confinement corresponds to zero eccentricity, while unconfined behavior corresponds to infinite eccentricity. The model then generates curves for eccentricities within these boundaries. The numerical approach developed has then been extended to account for shear interaction using the simplified modified compression field theory adopted by AASHTO LRFD Bridge Design Specifications 2014. Comparisons were then performed against experimental data and Response-2000, an analytical analysis tool based on AASHTO 1999 in order to validate the interaction domain generated. Finally, the developed models were implemented in the confined analysis software “KDOT Column Expert” to add FRP confinement effect and shear interaction.

Master of Science / Department of Mechanical and Nuclear Engineering / Youqi Wang / Two fiber reinforced polymer (FRP) bridge deck specimens were analyzed by means of acoustic emission (AE) monitoring during a series of loading cycles performed at various locations on the composite sandwich panels' surfaces. These panels were subjected to loads that were intended to test their structural response and characteristics without exposing them to a failure scenario. This allowed the sensors to record multiple data sets without fear of having to be placed on multiple panels that could have various characteristics that alter the signals recorded. The objective throughout the analysis ias to determine how the acoustic signals respond to loading cycles and various events can affect the acoustical data. In the process of performing this examination several steps were taken including threshold application, data collection, and sensor location analysis. The thresholds are important for lowering the size of the files containing the data, while keeping important information that could determine structurally significant information. Equally important is figuring out where and how the sensors should be placed on the panels in the first place in relation to other sensors, panel features and supporting beams. The data was subjected to analysis involving the response to applied loads, joint effects and failure analysis. Using previously developed techniques the information gathered was also analyzed in terms of what type of failure could be occurring within the structure itself. This somewhat aided in the analysis after an unplanned failure event occurred to determine what cause or causes might have lead to the occurrence. The basic analyses were separated into four sets, starting with the basic analysis to determine basic correlations to the loads applied. This was followed by joint and sensor location analyses, both of which took place using a two panel setup. The last set was created upon matrix failure of the panel and the subsequent investigation.

La détérioration des infrastructures au Canada due à la corrosion des armatures est l'un des défis majeurs de l'industrie de la construction. Les progrès récents dans la technologie des polymères ont conduit au développement d'une nouvelle génération de barres d'armature à base de fibres renforcées de polymères (PRF), (en particulier les fibres de verre). Ces barres, résistant à la corrosion, ont montré un grand potentiel d'utilisation pour mieux protéger les infrastructures en béton armé contre les effets dévastateurs de la corrosion. Avec la publication du nouveau code S807-10 "Spécifications pour les polymères renforcés de fibres" et la production de barres en PRF de très haute qualité, celles-ci représentent une alternative réaliste et rentable par rapport à l'armature en acier pour les structures en béton soumises à de sévères conditions environnementales. La conception des éléments en béton armé de barres en PRF est généralement gouvernée par l'état de service plutôt que l'état ultime. Par conséquent, il est nécessaire d'analyser les performances en flexion et le comportement en service en termes de déflexion et de largeur de fissures des éléments en PRF sous charges de service et de vérifier que ces éléments rencontrent les limites des codes. Aussi, de récents développements dans l'industrie des PRF ont conduit à l'introduction des barres en PRF avec des configurations de surface et des propriétés mécaniques différentes. Ces développements sont susceptibles d'affecter leur performance d'adhérence et, par conséquent, la largeur des fissures dans les éléments en PRF. Cependant, les codes de conception et les guidelines de calcul fournissent une valeur unique pour le coefficient d'adhérence (k[indice inférieur b]) en tenant compte des configurations de surface et en négligeant le type de barre en PRF, le diamètre de la barre, et le type de béton et de sa résistance. En outre, le code canadien S807-10 "Spécifications pour les polymères renforcés de fibres" fournit une étape en classant les barres en PRF par rapport à leur module d'élasticité (E[indices inférieurs frp]). Ces classifications ont été divisées en trois classes : Classe I (E[indices inférieurs frp]<50 GPa), Classe II (50 GPa [plus petit ou égal] E[indices inférieurs frp]< 60 GPa) et Classe III (E[indices inférieurs frp] [plus grand ou égal] 60 GPa). Ce programme de recherche vise à étudier expérimentalement le comportement en flexion des éléments en béton en service armé avec différents paramètres sous charges statiques. Le programme expérimental est basé sous plusieurs paramètres, dont les différents ratios de renforcement, différents types de barres (différentes classes comme classifiées par le CAN/CSA S807-10), le diamètre et la surface de la barre, la configuration ainsi que la résistance du béton. De plus, les recommandations actuelles de design pour les valeurs de k[indice inférieur b] et la vérification de la dépendance des valeurs de k[indice inférieur b] sur le type de barres (verre ou carbone), le diamètre des barres et le type de béton et sa résistance ont été étudiées. Le programme expérimental comprenait la fabrication et les essais sur 33 poutres à grande échelle, simplement appuyées et mesurant 4250 mm de long, 200 mm de large et 400 mm de hauteur. Vingt et sept poutres en béton ont été renforcées avec des barres en PRF à base de verre, quatre poutres en béton ont été renforcées avec des barres de PRF à base de carbone, et deux poutres ont été renforcées avec des barres en acier. Toutes les poutres ont été testées en flexion quatre points sur une portée libre de 3750 mm. Les paramètres d'essai étaient: le type de renforcement, le pourcentage d'armature, le diamètre des barres, configurations de surface et la résistance du béton. Les résultats de ces essais ont été présentés et discutés en termes de résistance du béton, de déflection, de la largeur des fissures, de déformations dans le béton et l'armature, de résistance en flexion et de mode de rupture. Dans les trois articles présentés dans cette thèse, le comportement en flexion et la performance des poutres renforcées de barres en PRFV et fabriquées avec un béton normal et un béton à haute performance ont été investigués, ainsi que les différentes classes de barres en PRFV et leurs configurations de surface. Les conclusions des investigations expérimentales et analytiques contribuent à l'évaluation des équations de prédiction de la déflection et des largeurs de fissures dans les codes de béton armé de PRF, pour prédire l'état de service des éléments en béton renforcés de PRF (déflection et largeur de fissures). En outre, à la lumière des résultats expérimentaux de cette étude, les équations de service (déflection et largeur des fissures) incorporées dans les codes et guidelines de design [ACI 440.1R-06, 2006; ISIS Manual No.3, 2007; CAN/CSA-S6.1S1, 2010; CAN/CSA-S806, 2012] ont été optimisées. En outre, les largeurs de fissures mesurées et les déformations ont été utilisées pour évaluer les valeurs courantes de k[indice inférieur b] fournies par les codes et les guidelines de calcul des PRF. En outre, les conclusions ne prennent pas en charge la valeur unique de k[indice inférieur b] pour les barres en PRF de types différents (carbone et verre) avec des configurations de surface similaires et s'est avéré être dépendant du diamètre de la barre.

Thesis (M.Tech.:Mechanical Engineering)-Dept. of Mechanical Engineering, Durban University of Technology, 2006 xv, iii, 108 leaves / Fibre Reinforced Plastics (FRPs) have been used in many practical structural applications due to their excellent strength and weight characteristics as well as the ability for their properties to be tailored to the requirements of a given application. Thus, designing with FRPs can be extremely challenging, particularly when the number of design variables contained in the design space is large. For example, to determine the ply orientations and the material properties optimally is typically difficult without a considered approach. Optimization of composite structures with respect to the ply angles is necessary to realize the full potential of fibre-reinforced materials. Evaluating the fitness of each candidate in the design space, and selecting the most efficient can be very time consuming and costly. Structures composed of composite materials often contain components which may be modelled as rectangular plates or cylindrical shells, for example. Modelling of components such as plates can be useful as it is a means of simplifying elements of structures, and this can save time and thus cost. Variations in manufacturing processes and user environment may affect the quality and performance of a product. It is usually beneficial to account for such variances or tolerances in the design process, and in fact, sometimes it may be crucial, particularly when the effect is of consequence. The work conducted within this project focused on methodologies for optimally designing fibre-reinforced laminated composite structures with the effects of manufacturing tolerances included. For this study it is assumed that the probability of any tolerance value occurring within the tolerance band, compared with any other, is equal, and thus the techniques are aimed at designing for the worst-case scenario. This thesis thus discusses four new procedures for the optimization of composite structures with the effects of manufacturing uncertainties included.

Adequate interfacial bond performance of Bonded Concrete Overlay (BCO) systems requires novel integration of material mixture design, compatibility model development, and interfacial bond design. This entails the use of the right materials, on the right substrate, in the right way, in order to secure the best possible composite behaviour. The overall composite performance of BCOs depends largely on achieving the right proportion of blend for the overlay material. The use of mixture experiments provides a flexible, easy, and quick way of optimizing multi-component materials of this nature. This study describes the use of optimization techniques within the concept of material mixture experiments for proportioning and designing the material constituents of a Bonded Roller Compacted Fibre Reinforced Polymer Modified Concrete (BRCFRPMC). By constraining the range of variability of the constituents, a feasible design space was created with 13 experimental points treated based on the required structural and elastic properties of the overlay. The optimum consistency-time for full consolidation and composite behaviour with the substrate ordinary Portland cement concrete (OPCC) was established between 34.05 and 34.87 seconds, while the resulting apparent maximum density achieves between 97.11% - 98.03% of the theoretical air-free density. In addition, compressive strength response at early and matured ages of 3 and 28 days were satisfied at 100% desirability. The elastic modulus response at age 3 showed 0% desirability, but attains about 99.96% of the target response by 28 days. The verification experiments conducted on each response property shows that positive correlations exist between the measured responses and the predicted values from the optimization analysis. Also, the bond capability of the optimum designed overlay material was evaluated using both tensile and shear bond strengths parameters. The overall assessment results showed that the overlay material exhibits good bonding with the substrate OPCC and would be able to withstand substantial stresses where sufficient surface texture is provided for aggregates interlocking. Other material properties included in the evaluation process of the overlay material included its tensile strength, coefficient of thermal expansion, and drying shrinkage. Stresses in the overlay, substrate, and at the interface were assessed analytically under various differential movement related conditions. Though the interface and the overlay material exhibited sufficient strength against thermal and shrinkage cracking, the theoretical shrinkage cracking in the overlay was predicted at 6.92MPa when fully restrained axially. Further, for effective fracture process description of the interface, experimentally determined parameters in shear and tension were coupled in Mixed-Mode Finite Element Analysis using differential edge deformation model between the overlay and the underlay. The results indicated that delamination in partial fracture process varied from that of complete fracture process, influenced distinctly and largely by the magnitude of the applied load. Other influencing factors in the analyses included the elastic mismatched properties, initial edge defect size, and the plane of loading. Lastly, analytical solution to the FEA problem was implemented using the proposed Modified Eigenvalue Buckling Analysis (MEBA). The result indicated that the proposed analytical method simulates and compares well with the FEA result. The proposed method also provided a good technique for predicting the Mixed-Mode Buckling failure Mode-Shape of the overlay.

Thesis (PhD (Civil Engineering))--University of Stellenbosch, 2007. / ECC (Engineered Cement-based Composites) is a type of HPC (High Performance Concrete) that was engineered to overcome the weaknesses of ordinary concrete. It shows high ductility as it can resist the full tensile load at a strain of more than 3 %. This superior response is achieved with multiple cracking under tensile loading which has a pseudo strain hardening phenomenon as result. The purpose of the research project reported in this dissertation is to investigate and characterise the time-dependant behaviour of ECC and create a constitutive model to numerically simulate the static and time-dependant behaviour of ECC. To investigate the time-dependant behaviour experimentally, rate and creep tests were done on the meso- and macro-level while rate tests were done on the structurallevel. The meso-level was represented by the pull-out testing of fibres embedded in the cement-based matrix and direct tensile tests were done for the macro-level. Flexural tests on thin beams were done to simulate the structural-level. Strong time-dependant behaviour was found on all three these levels. On the meso-level, the most prominent finding is that the failure mechanism can change with a change of strain rate, i.e. fibre pull-out at a low pull-out rate, while with a high pullout rate, fibre rupture can occur. Even though the strength of a tensile specimen on the macro-level showed a dependence on the strain rate, the ductility remained constant over four orders of magnitude of the strain rate. On the structural-level, however, a reduction of the flexural ductility was found with an increase of the ...

Thesis (MScEng (Civil Engineering)--University of Stellenbosch, 2006. / Some experiments utilizing the shear capacity of Engineered Cement-based Composites (ECC) have suggested that elimination of shear reinforcement is feasible when the concrete matrix is replaced by ECC. However, actual application and more rigorous cost analysis are prevented by the fact that the shear stress and strain properties of ECC have not yet been characterized as accurately as the tensile properties. This study focuses on the investigation of the shear property of ECC. The study starts with a survey and comparison of existing shear tests for composite materials. The Iosipescu shear test concept is chosen as the most objective method for ECC, and subsequently, modified for specific application on ECC by simple analytical design and finite element refinement. The modified Iosipescu shear test method is applied on, four types of ECC specimens with different fibre content (0%, 1%, 2%, 2.5% by volume), which have been cast in specially designed moulds and cured in laboratory conditions. Three phases of shear measurements are used to check the shear test appropriateness and study the shear mechanical properties of ECC. The failure mode is verified in the first phase, detailed measurement of the shear strain and shear stress is performed and recorded in the second phase, and in the third phase more information about the ductility of diagonal cracking is obtained by measurement of the tensile principal deformation. By also conducting direct tensile tests on specimens of the exact same mix, information of both uniaxial tension and shear behaviour is available, from which elastic and shear moduli, as well as Poisson’s ratio of ECC are computed. A first step toward application of this knowledge of the shear behaviour of ECC is taken by studying the response of shear-dominated beams and beam-columns of reinforced concrete and reinforced concrete combined with ECC as the outer crusts. These beams were prepared and tested by other members of the research group of the Division for Structural Engineering of the University of Stellenbosch. It is shown that ECC can indeed successfully replace shear reinforcing steel, due to its shear capacity.

Thesis (MScEng (Civil Engineering))--University of Stellenbosch, 2007. / Bonded overlays are increasingly used in concrete and reinforced concrete repair and rehabilitation applications, despite the high probability of interfacial debonding. Reasons for such failures include inefficient substrate surface preparations, inappropriate overlay materials, poor curing conditions and time dependent influences. The introduction of engineered cement-based composite (ECC) as an overlay or repair material, does not only address durability aspects but also structural performance. The associated ductility of the material induces a high performance aspect where applied. It is crucial to execute reliable design methods, especially at interfacial level, in order to harness the ductility at hand. The fact of the matter is that through identifying the required performance, one can engineer an optimal bond through implementation of reliable substrate surface preparation techniques (SSPT’s). ECC is a material which exhibits ductile mechanical behaviour. The material matrix is reinforced with synthetic fibres, in the case of this study, poly vinyl alcohol (PVA) fibres were used. The introduction of fibres induces strain-hardening behaviour when in tension. Strain-hardening occurs from the first crack onwards and is accompanied by ductile behaviour, due to a multiple cracking phenomenon. Multiple cracking continues until the increased tensile load incurs localising of an existing crack. The literature study investigates bond properties and bond model parameter test methods. A review of composite design, mainly concrete to concrete, in local and international codes discloses design specifications towards calculating interfacial shear bonds. The interfacial transition zone (ITZ) between the aggregate and cement matrix of concrete is used to define the interfacial bond characteristics and processes. The next step is to investigate a variety of interfacial shear and tensile test methods, in order to implement the most suitable tests.

Thesis (MScEng (Civil Engineering))--University of Stellenbosch, 2011. / ENGLISH ABSTRACT: Plastic shrinkage cracking (PSC) is the cracking caused by the early age shrinkage of concrete within the first few hours after the concrete has been cast. It results in unsightly surface cracks that serve as pathways whereby corroding agents can penetrate the concrete which shortens the expected service life of a structure. PSC is primarily a problem at large exposed concrete surfaces for example bridge decks and slabs placed in environmental conditions with high evaporation rates. Most precautionary measures for PSC are externally applied and aimed to reduce the water loss through evaporation. The addition of a low dosage of polymeric fibres to conventional concrete is an internal preventative measure which has been shown to reduce PSC. The mechanisms involved with PSC in conventional and low volume fibre reinforced concrete (LV-FRC) are however not clearly understood. This lack of knowledge and guidance leads to neglect and ineffective use of preventative measures. The objective of this study is to provide the fundamental understanding of the phenomena of PSC. To achieve the objective, an in depth background study and experiments were conducted on fresh conventional concrete and LV-FRC. The three essential mechanisms required for PSC are: 1→ Capillary pressure build-up between the particles of the concrete is the source of shrinkage. 2→ Air entry into a concrete initiates cracking. 3→ Restraint of the concrete is required for crack forming. The experiments showed the following significant findings for conventional and LV-FRC: PSC is only possible once all the bleeding water at the surface has evaporated and once air entry has occurred. The critical period where the majority of the PSC occurs is between the initial and final set of concrete. Any preventative measure for PSC is most effective during this period. The bleeding characteristics of a mix have a significant influence on PSC. Adding a low volume of polymeric fibres to concrete reduces PSC due to the added resistance that fibres give to crack widening, which increases significantly from the start of the critical period. The fundamental knowledge gained from this study can be utilized to develop a practical model for the design and prevention of PSC in conventional concrete and LV-FRC. / AFRIKAANSE OPSOMMING: Plastiese krimp krake (PSK) is die krake wat gevorm word a.g.v. die vroeë krimping van beton binne die eerste paar ure nadat die beton gegiet is. Dit veroorsaak onooglike oppervlak krake wat dien as kanale waardeur korrosie agente die beton kan binnedring om so die dienstydperk van die struktuur te verkort. Dit is hoofsaaklik ʼn probleem by groot blootgestelde beton oppervlaktes soos brug dekke en blaaie wat gegiet is in klimaat kondisies met hoë verdamping tempo’s. Meeste voorsorgmaatreëls vir PSK word ekstern aangewend en beperk die water verlies as gevolg van verdamping. Die byvoeging van ʼn lae volume polimeriese vesels is ʼn interne voorsorgmaatreël wat bekend is om PSK te verminder. Die meganismes betrokke ten opsigte van PSK in gewone beton en lae volume vesel versterkte beton (LV-VVB) is vaag. Die vaagheid en tekort aan riglyne lei tot nalatigheid en oneffektiewe aanwending van voorsorgmaatreëls. Die doel van die studie is om die fundamentele kennis oor die fenomeen van PSK te gee. Om die doel te bereik is ʼn indiepte agtergrond studie en eksperimente uitgevoer op gewone beton en LV-VVB. Die drie meganismes benodig vir PSK is: 1→ Kapillêre druk tussen die deeltjies van die beton is die hoof bron van krimping. 2→ Lugindringing in die beton wat krake inisieer. 3→ Inklemming van die beton is noodsaaklik vir kraakvorming. Die eksperimente het die volgende noemenswaardige bevindinge opgelewer: PSK is slegs moontlik indien al die bloeiwater van die beton oppervlakte verdamp het en indien lug die beton ingedring het. Die kritiese periode waar die meerderheid van die PSK plaasvind is tussen die aanvanklike en finale set van die beton. Enige voorsorgmaatreël vir PSK is mees effektief gedurende die periode. Die bloei eienskappe van ʼn meng het ʼn noemenswaardige effek op die PSK. Die byvoeging van ʼn lae volume polimeriese vesels tot beton verminder die PSK deur die addisionele weerstand wat die vesels bied teen die toename in kraakwydte. Die weerstand vergroot noemenswaardig vanaf die begin van die kritiese periode. Die fundamentele kennis wat in die studie opgedoen is, kan gebruik word vir die ontwikkeling van ʼn praktiese model vir die ontwerp en verhoed van PSK in gewone beton en LV-VVB.

published_or_final_version / abstract / Civil Engineering / Master / Master of Philosophy