<p>Seismic isolation is a seismic design philosophy that aims to reduce the demand on structures as opposed to increasing their capacity to endure forces. Seismic isolation can be achieved by placing isolating bearings with relatively low stiffness compared to the structure itself beneath the superstructure. This low stiffness layer increases the structural period, shifting the structure into a period range of low seismic energy content.</p> <p>The objectives of this research were to investigate the dynamic properties, durability and limitations of stable unbonded fibre reinforced elastomeric isolator (SU-FREI) bearings. Vertical compression testing indicated the bearings possessed adequate vertical stiffness. Due to lack of bonding at the bearing interface surfaces rollover deformation was observed to occur during lateral cyclic testing. This response behaviour was found to result in advantageous effective lateral stiffness and damping properties. The bearings maintained stability during rollout testing while serviceability and fatigue testing both conformed to code specified test specimen adequacy limitations. Experimental shake table testing showed that the isolated structure behaved essentially as a rigid body during testing. Test results showed that a SU‐FREI isolation system significantly reduced the seismic demand on the structure.</p> <p>Modelling of the bearings dynamic properties was completed using a bilinear model and a backbone curve model. Both models showed adequate results in predicting experimental peak responses. A simplified design spectrum analysis was presented and used to model the structure in four Canadian cities. This design spectrum analysis approach showed adequate capabilities in predicting peak response values, such that the method could be used in preliminary analysis and design of isolated structures.</p> / Master of Applied Science (MASc)

Yes / This paper investigates the feasibility of using artificial neural networks (NNs) to predict the shear capacity of concrete members reinforced longitudinally with fibre reinforced polymer (FRP) bars, and without any shear reinforcement. An experimental database of 138 test specimens failed in shear is created and used to train and test NNs as well as to assess the accuracy of three existing shear design methods. The created NN predicted to a high level of accuracy the shear capacity of FRP reinforced concrete members. Garson index was employed to identify the relative importance of the influencing parameters on the shear capacity based on the trained NNs weightings. A parametric analysis was also conducted using the trained NN to establish the trend of the main influencing variables on the shear capacity. Many of the assumptions made by the shear design methods are predicted by the NN developed; however, few are inconsistent with the NN predictions.

Hydraulic systems are used in many fields of applications for different functions like energy storage in hybrid systems. Generally the mass of hydraulic systems plays a key role especially for mobile hydraulics (construction machines, trucks, cars) and hydraulic aircraft systems. The main product properties like energy efficiency or payload can be improved by reducing the mass. In this connection carbon fiber reinforced plastics (CFRP) with their superior specific strength and stiffness open up new chances to acquire new lightweight potentials compared to metallic components. However, complex quality control and failure identification slow down the substitution of metals by fiber-reinforced plastics (FRP). But the lower manufacturing temperatures of FRP compared to metals allow the integration of sensors within FRP-components. These sensors then can be advantageously used for many functions like quality control during the manufacturing process or structural health monitoring (SHM) for failure detection during their life cycle. Thus, lightweight hydraulic components made of composite materials as well as sensor integration in composite components are a main fields of research and development at the Institute of Lightweight Engineering and Polymer Technology (ILK) of the TU Dresden as well as at the Leichtbau-Zentrum Sachsen GmbH (LZS).

Thesis (MScEng)--Stellenbosch University, 2011. / ENGLISH ABSTRACT: Strain hardening cement‐based composites (SHCC) are fibre‐reinforced composites designed to form multiple fine cracks under tensile and flexural load. The cracks are controlled to small widths, whereby significant toughness, or energy dissipation, is realised on the one hand, and high resistance to gas and liquid ingress is maintained on the other hand. These two physical phenomena define application fields of SHCC, i.e. for instance elements of buildings and infrastructure for enhanced earthquake resistance, and protection of steel bars under service loads which lead to crack formation. Also exploiting the potential protection offered by SHCC to existing structures, thin overlays have been applied to existing dam faces, reinforced concrete retaining walls, water channels and RC road pavements. The layers vary between 20 and 40 mm in thickness. Considering the fibre length, usually 8 or 12 mm, as well as the application method, such thin layers may have dominantly two dimensional fibre orientation, with little or no component in the layer thickness direction. While several research groups have performed uniaxial tensile tests and flexural tests on SHCC specimens, little or no information is available on SHCC response to biaxial loading, as is to be expected in road pavement repair layers, or other repair layers. This paper reports the results of biaxial testing of 20 mm thick SHCC specimens produced in such a way to have dominantly two‐dimensional fibre orientation, and another group of specimens produced by cutting from larger specimens, whereby three‐dimensional fibre orientation was preserved in the resulting 20 mm thick specimens. Biaxial tests were performed in three quadrants, i.e. compressioncompression, compression‐tension, and tension‐tension. A clear fibre orientation‐related difference in the failure patterns involves out‐of‐plane splitting under biaxial compression of specimens with twodimensional fibre orientation, at significantly lower load, as opposed to in‐plane tensile splitting of specimens containing three‐dimensional fibre orientation. / AFRIKAANSE OPSOMMING: Vervormingsverhardende sement‐gebaseerde saamgestelde materiale (SHCC) is veselversterke saamgestelde materiale wat ontwerp is om verskeie fyn krakies te vorm onder trekspanning en buig spanning. Die kraakbreedtes word beheer, waardeur betekenisvolle taaiheid verkry, of energie verlies beheer word aan die een kant, en die hoë weerstand teen die gas en die vloeistof penetrasie aan die ander kant gehandhaaf word. Hierdie twee fisiese verskynsels definieer die toepassingsvelde van SHCC, d.w.s vir byvoorbeeld elemente van geboue en infrastruktuur vir verbeterde aardbewing weerstand, en die beskerming van staal stawe onder die dienslaste wat lei vorming te kraak. By eksploitasie van die potensiële beskerming aangebied deur SHCC aan bestaande strukture, is dun oorlae op bestaande dam walle, versterkte beton keermure, water kanale en staal‐versterkte beton paaie gebruik. Die SHCC lae wissel tussen 20 en 40 mm in dikte. Met inagneming van die vesel lengte, gewoonlik 8 of 12 mm, sowel as die toepassingsmetode, kan so 'n dun lag ‘n oorheersend tweedimensionele vesel oriëntasie hê, met min of geen komponent in die rigting van die laag dikte nie. Terwyl verskeie navorsingsgroepe eenassige trektoetse en buigtoetse op SHCC monsters gedoen het; is daar min of geen inligting beskikbaar op SHCC se reaksie op biaksiale belasting, soos verwag kan word in die pad herstel lae, of ander herstel lae. Hierdie verslag rapporteer die resultate van die biaksiale toetsing van 20 mm dik SHCC monsters wat op so 'n manier gemaak word om dominante twee‐dimensionele vesel oriëntasie te hê, en 'n ander groep monsters wat deur die sny van groter monsters, waarvolgens die drie‐dimensionele vesel oriëntasie verseker is. Biaksiale toetse is uitgevoer in drie kwadrante, d.w.s druk‐druk, druk‐trek en trek‐trek. 'n Duidelike verskil in die falingspatrone, aan die hand van vesel oriëntasie, behels uit‐vlak splyting onder biaksiale toetsing van monsters met twee‐dimensionele vesel oriëntasie, op 'n aansienlik laer lading, in teenstelling met die in‐vlak trek splyting van monsters wat ‘n drie‐dimensionele vesel oriëntasie het.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: Strain Hardening Cement Based Composite (SHCC) is a type of High Performance Fibre Reinforced Cement-based Composite (HPFRCC). SHCC contains randomly distributed short fibres which improve the ductility of the material and can resist the full tensile load at strains up to 5 %. When SHCC is subjected to tensile loading, fine multiple cracking occurs that portrays a pseudo strain hardening effect as a result. The multiple cracking is what sets SHCC aside from conventional Reinforced Concrete (RC). Conventional RC forms one large crack that results in durability problems. The multiple cracks of SHCC typically have an average crack width of less than 80 μm (Adendorff, 2009), resulting in an improved durability compared to conventional RC. The aim of this research project is to quantify the cracking behaviour of SHCC which can be used to quantify the durability of SHCC. The cracking behaviour is described using a statistical distribution model, which represents the crack widths distribution and a mathematical expression that describes the crack pattern. The cracking behaviour was determined by measuring the cracks during quasi-static uni-axial tensile tests. The cracking data was collected with the aid of a non-contact surface strain measuring system, namely the ARAMIS system. An investigation was performed on the crack measuring setup (ARAMIS) to define a crack definition that was used during the determination of the cracking behaviour of SHCC. Several different statistical distributions were considered to describe the distribution of the crack widths of SHCC. A mathematical expression named the Crack Proximity Index (CPI) which represents the distances of the cracks to each other was used to describe the crack pattern of SHCC. The Gamma distribution was found to best represent the crack widths of SHCC. It was observed that different crack patterns can be found at the same tensile strain and that the CPI would differ even though the same crack width distribution was found. A statistical distribution model was therefore found to describe the CPI distribution of SHCC at different tensile strains and it was established that the Log-normal distribution best describes the CPI distribution of SHCC. After the cracking behaviour of SHCC was determined for quasi-static tensile loading, an investigation was performed to compare it to the cracking behaviour under flexural loading. A difference in the crack widths, number of cracks and crack pattern was found between bending and tension. Therefore it was concluded that the cracking behaviour for SHCC is different under flexural loading than in tension. / AFRIKAANSE OPSOMMING: “Strain Hardening Cement-based Composite” (SHCC) is ‘n tipe “High Performance Fibre Reinforced Cement-based Composite” (HPFRCC). SHCC bevat kort vesels wat ewekansig verspreid is, wat die duktiliteit van die material verbeter en dit kan die maksimum trekkrag weerstaan tot en met ‘n vervorming van 5 %. Wanneer SHCC belas word met ‘n trekkrag, vorm verskeie fyn krake wat ‘n sogenaamde vervormingsverharding voorstel. Die verskeie krake onderskei SHCC van normale bewapende beton. Normale bewapende beton vorm een groot kraak met die gevolg dat duursaamheidsprobleme ontstaan. Die gemiddelde kraakwydte van SHCC is minder as 80 μm (Adendorff, 2009) en het dus ‘n beter duursaamheid as normale bewapende beton. Die doel van die navorsingsprojek is om die kraak gedrag van SHCC te kwantifiseer en wat dan gebruik kan word om die duursaamheid van SHCC te kwantifiseer. Die kraak gedrag is beskryf deur ‘n statistiese verspreiding model wat die kraak wydtes se verspreiding voorstel en ‘n wiskundige uitdrukking wat die kraak patroon beskryf. Die kraak gedrag was bepaal deur die krake te meet tydens die semi-statiese een-asige trek toetse. Die kraak data was met behulp van ‘n optiese vervormings toestel, naamlik die ARAMIS, versamel. ‘n Ondersoek is gedoen op die kraak meetings opstelling (ARAMIS), om ‘n kraak definisie te definieer wat gebruik is om die kraak gedrag te bepaal. Daar is gekyk na verskeie statistiese verdelings om die kraak wydtes van SHCC te beskryf. Die kraak patroon van SHCC is beskryf met ‘n wiskundige uitdrukking genoem die “Crack Proximity Index” (CPI) wat die krake se afstande van mekaar voorstel. Dit is bevind dat die Gamma verdeling die kraak wydtes van SHCC die beste beskryf. Daar is waargeneem dat verskillende kraak patrone by dieselfde vervorming verkry kan word en dat die CPI kan verskil al is die kraak wydte verdeling dieselfde. ‘n Statistiese verdelingsmodel is dus gevind om die CPI verdeling van SHCC te beskryf by verskillende vervormings, en daar is vasgestel dat die Log-normaal verdeling die CPI verdeling van SHCC die beste beskryf. Nadat die kraak gedrag van SHCC bepaal is vir semi-statiese trek-belasting, is ‘n ondersoek gedoen waar die trek-kraak gedrag vergelyk is met buig-kraak gedrag. ‘n Verskil in die kraak wydtes, aantal krake en kraak patroon is gevind tussen buiging en trek. Dus is die gevolgtrekking gemaak dat die kraak gedrag van SHCC verskillend is in buiging as in trek.

In this thesis, new design concepts for arch bridges using ultra high-performance fibre-reinforced concrete are developed for spans of 50 to 400 m. These concepts are light-weight and efficient, and thus have the potential to significantly reduce the cost of construction. Lightness is achieved by the thinning of structural components and the efficient use of precompression in the arch, rather than by the decrease of bending stiffness. Using the advanced properties of the material, the design concepts were shown to reduce the consumption of concrete in arch bridges by more than 50% relative to arches built using conventional concrete technology. In addition to span length, other design parameters including span-to-rise ratio and deck-stiffening were considered, resulting in a total of seventy-two design concepts. Other important contributions made in this thesis include: (1) the development of a simple analytical model that describes the transition of shallow arches between pure arch behaviour and pure beam behaviour, (2) a comprehensive comparative study of 58 existing concrete arch bridges that characterizes the current state-of-the-art and serves as a valuable reference design tool, and (3) the development and experimental validation of general and simplified methods for calculating the capacity of slender ultra high-performance fibre-reinforced concrete members under compression and bending. The research presented in this thesis provides a means for designers to take full advantage of the high compressive and tensile strengths of the concrete and hence to exploit the economic potential offered by the material.

For members and flat slabs without shear reinforcement, the shear and punching shear strength are often the determining design criteria. These failure modes are characterized by a fragile behaviour implying possible partial or total collapse of the structure. Despite extensive research in this field, shear and punching shear in reinforced and prestressed concrete structures, remain complex phenomena so much that the current approach is often empirical or simplified. The ability of Steel Fibre Reinforced Concrete (SFRC) to reduce shear reinforcement in reinforced and prestressed concrete members and slabs,or even eliminate it, is supported by several experimental studies. However its practical application remains marginal mainly due to the lack of standard, procedures and rules adapted to its performance. The stationary processes in precast industry offer optimal possibilities for using high performance cementitious materials such as Self Compacting Concrete (SCC) and High Strength Concrete (HSC). For the author, the combination of High Performance Concrete and steel fibres is the following step in the development and the optimization of this industry. The High Performance Fibre Reinforced Concrete (HPFRC) stands between conventional SFRC and Ultra-High Performance Fibre Reinforced Concrete (UHPFRC). The HPFRC exhibiting a good strength/cost ratio is, thus, an alternative of UHPFRC for precast elements. The principal aim of this work was to analyse the shear and punching shear behaviour of HPFRC and UHPFRC structures without transversal reinforcement and to propose recommendations and design models adapted for practitioners. Several experimental studies on structural elements, i.e. beams and slabs, were undertaken for this purpose. Firstly, an original experimental campaign was performed on pre-tensioned members in HPFRC. A total number of six shear-critical beams of a 3.6 m span each, and two full scale beams of a 12 m span each, were tested in order to evaluate the shear and flexural strength. The principal parameter between the specimens was the fibres (...)

The natural hip joint in healthy people has a very low friction with very little (or no) wear. It works as a dynamically loaded bearing and is subjected to about 1-2 million cycles of loading per year. The applied load is the body weight which is tripled when walking and even higher during other activities such as running and jumping. Unfortunately these joints are not always healthy due to various causes such as fractures or disease leading to severe pain which necessitates joint replacement. Currently, the orthopaedic industries are working towards developing an ideal artificial hip joint with low wear, low friction, good lubrication, better fixation/stability and biocompatibility. Many different designs and materials have been investigated with some promising new implants which can be used depending on patients' individual need (large or small joint), activity and age. In this work, two types of artificial hip joints were tested for friction and lubrication studies: Metal-on-Metal (MoM) Biomet hip resurfacing ReCaps with large diameters (>35-60 mm) and different diametral clearances (~ 60-350 µm), and Zirconia Toughened Alumina (ZTA) heads against carbon-fibre-reinforced poly-ether-ether ketone (CFR PEEK) cups with different diameters (>35-60 mm) and diametral clearances (60-1860 µm). Seven serum-based lubricants with different viscosities were used with and without carboxy methyl cellulose (CMC) additions as gelling agent to increase viscosity depending on the CMC content. The maximum load applied was 2000 N for the stance phase with a minimum load of 100 N for the swing phase. A Pro-Sim friction hip simulator was used to investigate the frictional torque generated between the articulating surfaces so as the friction factor can be calculated. Stribeck analysis was then employed to assess the mode of lubrication. For the metal-on-metal hip resurfacing joints, the friction factors were in the range 0.03-0.151 and those for the ZTA ceramic heads versus CFR PEEK cups were in the range 0.006-0.32. Stribeck analyses showed mainly mixed lubrication for both MoM and ZTA ceramic-on-CFR PEEK joints. The experimental results were in agreement with most of the theoretical calculations suggesting mixed lubricating regimes at low viscosities and moving on to fluid film lubrication at higher viscosities. Joints with larger-diameters, lower clearances and lower surface roughness exhibited a higher lambda ratio suggesting improved lubrication. Viscosity flow curves for the serum-based lubricants having viscosity ≤ 0.00524 Pas showed non-linear relationship between viscosity and shear rate indicating non-Newtonian flow with pseudoplastic or shear-thinning characteristic, i.e. viscosity decreased as shear rate increased up to shear rates of ~ 1000 s⁻¹. However, at shear rates greater than 1000 s⁻¹ Newtonian flow became dominant with almost constant viscosity, i.e. a linear relationship between shear stress and shear rate. On the other hand, viscosity flow curves for the lubricants with viscosity ≥ 0.0128 Pas showed non-Newtonian behaviour up to a shear rate of 3000 s⁻¹ with shear-thinning characteristic.

A novel type of precast, prestressed concrete structural element is being implemented in load-bearing systems in buildings. These structural elements combine the use of high-performance, self-consolidating concrete (HPSCC) and non-corroding carbon fibre reinforced polymer (CFRP) prestressing tendons; this produces highly optimized, slender structural elements with excellent serviceability and (presumed) extended service lives. More widely, the use of new construction techniques, innovative materials, and ground-breaking designs is increasingly commonplace in today's rapidly evolving building construction industry. However, the performance of these and other structural elements in fire is in general not well known and must be understood before these can be used with confidence in load-bearing applications where structural fire resistance is a concern. Structural fire testing has traditionally relied on the use of the standard fire resistance test (i.e. furnace test) for assuring regulatory compliance of structural elements and assemblies, and in many cases also for developing the scientific understanding of structural response to fire. Conceived in the early 1900s and fundamentally unchanged since then, the standard testing procedure is characterized by its high cost and low repeatability. A novel test method, the Heat-Transfer Rate Inducing System (H-TRIS), resulting from a mental shift associated with controlling the thermal exposure not by temperature (e.g. temperature measured by thermocouples) but rather by the time-history of incident heat flux, was conceived, developed, and validated within the scope of the work presented in this thesis. H-TRIS allows for experimental studies to be carried out with high repeatability, imposing rationally quantifiable thermal exposure, all at low economic and temporal cost. The research presented in this thesis fundamentally seeks to examine and understand the behaviour of CFRP prestressed HPSCC structural elements in fire, with emphasis placed on undesired 'premature' failure mechanisms linked to the occurrence of heat-induced concrete spalling and/or loss of bond between the pretensioned CFRP tendons and the concrete. Results from fire resistance tests presented herein show that, although compliant with testing standards, temperature distributions inside furnaces (5 to 10% deviation) appear to influence the occurrence of heat-induced concrete spalling for specimens tested simultaneously during a single test; fair comparison of test results is therefore questionable if thermal exposure variability is not explicitly considered. In line with the aims of the research presented in this thesis, H-TRIS is used to carry out multiple comprehensive studies on the occurrence of concrete spalling and bond behaviour of CFRP tendons; imposing a quantified, reproducible and rational thermal exposure. Test results led to the conclusion that a "one size fits all" approach for mitigating the risk of heat-induced concrete spalling (e.g. prescribed dose of polypropylene (PP) fibres included in fresh concrete), appears to be ineffective and inappropriate in some of the conditions examined. This work demonstrates that PP fibre cross section and individual fibre length can have an influence on the risk of spalling for the HPSCC mixes tested herein. The testing presented herein has convincingly shown, for the first time using multiple repeated tests under tightly controlled thermal and mechanical conditions, that spalling depends not only on the thermal gradients in concrete during heating but also on the size and restraint conditions of the tested specimen. Furthermore, observations from large scale standard fire resistance tests showed that loss of bond strength of pretensioned CFRP tendons occurred at a 'critical' temperature of the tendons in the heated region, irrespective of the temperature of the tendons at the prestress transfer length, in unheated overhangs. This contradicts conventional wisdom for the structural fire safety design of concrete elements pretensioned with CFRP, in which a minimum unheated overhang is generally prescribed. Overall, the research studies presented in this thesis showed that a rational and practical understanding of the behaviour of CFRP prestressed HPSCC structural elements during real fires is unlikely to be achieved only by performing additional standard fire resistance tests. Hence, H-TRIS presents an opportunity to help promote an industry-wide move away from the contemporary pass/fail and costly furnace testing environment. Recommendations for further research to achieve the above goal are provided.

Neste trabalho investiga-se o comportamento resistente de lajes-cogumelo de concreto armado, analisando-se as possibilidades de melhoria de desempenho com relação ao fenômeno de punção, pelo emprego de concreto de alta resistência, pelo reforço com fibras de aço e pelo uso de armaduras transversais de combate à punção, através de ensaios de modelos de lajes-cogumelo quadradas que representam a ligação laje-pilar para o caso do pilar interno. Apresenta-se também uma revisão de conhecimentos sobre as lajes-cogumelo, o seu comportamento estrutural com ênfase no fenômeno da punção, e os principais conceitos sobre os concretos de alta resistência e os compósitos constituídos de matriz de cimento reforçada com fibras. Doze modelos de laje-cogumelo foram ensaiados com diferentes combinações de concreto de alta resistência, concreto de resistência convencional, armadura transversal e volume de fibras (0%, 0,75% e 1,5%). Um acréscimo significativo de resistência à punção foi observado, devido ao uso de concreto de alta resistência e à adição de fibras. A combinação de concreto de alta resistência com 1,5% de volume de fibras e armadura transversal proporcionaram o dobro de aumento na resistência à punção em relação ao modelo de concreto convencional sem armadura transversal e sem adição de fibras. A adição de fibras é a suposta responsável por cerca de 50% de acréscimo de resistência e o aumento da ductilidade. Outras comparações incluindo as previsões teóricas (Texto Base da NB1/94, CEB/90, AGI 318/89 e EUROCODE N.2) são comentadas. / This work investigates the behavior of reinforced concrete flat slabs, analysing the possibility of performance improvement, in relation to punching shear phenomenon, regarding to the use of high strength concrete, the addition of steel fibres and the use of transversal steel reinforcement against punching shear, through tests of flat slab square models that represent the slab-column connection, for the case of an interior column. lt introduce a revision of knowledge of flat slabs, their structural behavior with emphasis on the punching shear phenomenon, and the main concepts about high strength concretes and the composites made of cement matrix reinforced with fibres. Twelve flat slab models were tested in different combinations of high strength concrete, ordinary strength, shear reinforcement and steel fibre volume fraction (0%, 0,75% e 1,5%). A significant increase in the punching shear strength was observed, either due to the use of high strength and the addition of steel fibres. The combination of high strength concrete with 1,5% fibre volume fraction and shear reinforcement provide twice the punching shear resistance of an ordinary concrete strength model without shear reinforcement and without fibre. Fibre addition is supposed to be responsible by about 50% of the resistance improvement and the increase of ductility. Other comparisons including theoretical previsions (Texto Base da NB1/94, CEB/90, ACI 318/89 e EUROCODE N.2) are commented.