This report is about how to decide which method is the most suitable as floor covering at project Klammerdamm in the centre of Halmstad. The covering has to be fire resistant and soundproof in order to protect the wood structure and stop noise from traveling between apartments. There are two possibilities either traditional gypsum board or gypsum-based self leveling underlayment. The roads around the construction site are narrow. A regular twenty-five meter long truck has no possibility to reach the site. The construction site is small and the storage area is limited. Good planning is one condition, among many others, that has to be fulfilled to make this project doable. All relevant parameters has been taken into account and analyzed with a decision model.

Thesis (M.S.)--Virginia Polytechnic Institute, 1955. / Vita. Includes bibliographical references (leaf 37). Also available via the Internet.

Thesis (M.S.)--West Virginia University, 2001. / Title from document title page. Document formatted into pages; contains x, 127 p. : ill. (some col.). Includes abstract. Includes bibliographical references (p. 89-92).

No description available.

The flooring industry is a market that constantly changing every year with new products and improvements. The purpose of this report is to uncover which of the floors, linoleum and vinyl with or without PUR reinforced surface has the lowest life cycle cost for the customer over a 30-year period. The scope of the study is to investigate the three different floors in the public sector in Sweden, Norway, and Finland. A similar study was made many years ago where remarkable result was uncovered. The way used to determining the result in this study is made by two different methods within the LCC. The LCC calculations in this study are based on the primary data collections; qualitative interviews, time study, and observations. Secondary data have also been used in the report. When a customer invests in a floor there are three major costs purchasing, installation, and maintenance. Maintenance will ultimately be the biggest cost because it extends over the entire life cycle while the others are two fixed costs. The analysis uncover that the amount of water and chemical usage to maintain the floors has reduced since the old study. The consumption that has increased is the energy, a result from the increase usage of cleaning machines in the public sector. The most profitable floor to invest in is the vinyl with PUR reinforced surface. This floor has in Sweden and Norway a higher purchasing price than linoleum and vinyl without PUR reinforced surface but in the long run (30 years) its total life cycle cost are lesser than the two others. If the public sector in Sweden invests in a vinyl floor with reinforced PUR surface instead of a vinyl without PUR, the life cycle cost at a hospital or municipality will be reduced by 16,3 percent.

M. Tech. Chemical Engineering / Cement based materials are of enormous technological importance and their satisfaction depends on being able to transport and mould them in the freshly mixed state. The problem of the degradation or concrete is of interests to modern society, not only in terms of money, but in terms of discomfort and safety. Global research show concrete consumption around the world to be second only to water. The situation clearly indicates the significance and the huge role concrete has in the construction industry and in the global economy. This work was to investigate the various methods of increasing the life span of concrete without compromising its properties. The techniques for improving the physical properties of concrete and the effect of bacterial biofilm were studied especially for sanitary floors of food processing industries. The aim of this study is to improve the physical, mechanical and microbial properties of concrete floors in food processing industries by extending the life span of concrete materials.

No description available.

No

Building materials are a major source of indoor air contaminants. Volatile organic compounds (VOCs) are an important class of contaminants prevalent in indoor air. Attempts have been made to model the emission of VOCs from building materials. Diffusion has been shown to control the rate of mass transfer within certain types of building materials. The primary objective of this research is to develop a fundamental diffusion-based model for single and double layer building materials. The single-layer model considers a slab of material located on the floor of a chamber or room with the material acting either as a source or a sink for VOCs. The behavior of the model is governed by the material phase diffusion coefficient (D), the material/air partition coefficient (K), the concentration of VOC in the influent air stream, and the initial concentration within the material phase. The single-layer model extends a previously developed version, incorporating the non-uniform initial concentration inside the building material and a transient influent concentration. Experimental work is performed to check the validity of the model. A steel chamber housing a piece of vinyl flooring is used to simulate building material within a room. D and K values for two representative VOCs, n-dodecane and phenol, are available from earlier experiments. These parameters are used in the model to predict the VOC concentration inside the chamber. The predicted values compare very well to the observed experimental data. A double layer version of the model is developed and studied from a theoretical perspective. The model also permits a time dependent influent concentration and a non-uniform initial concentration profile within each of the two layers. A parametric analysis is performed varying the ratio of the diffusion coefficients, the partition coefficients and the thickness of the two layers. Three cases of practical interest are studied using the double-layer model. The use of a thin low-permeability barrier layer placed on top of a building material is shown to hold considerable promise for reducing the emission rate of VOCs into indoor air. / Master of Science

Full size wood joist floors were built and their frequencies were measured. Double tee-beam floors were built and also cut from the full size floors and their frequencies were measured. The floor joists investigated included: solid sawn, parallel chord floor trusses, and composite I -joists. The first natural frequency of each tee-beam floor was predicted after measuring the deflection under imposed loading. A design procedure is presented to predict the fundamental frequency of wood joist floors from tabulated material properties / Master of Science