L'actuel investigation numérique du Gurson-Tvergaard-Needleman (GTN) modèle avancé est une extension du travail de Ben Bettaieb et al. (2011). Le modèle a été implémenté à l'aide d'une sous routine (VUMAT) contenu dans le code commerciale d'éléments finis Abaqus/explicit. Le modèle d'endommagement améliore l'original en intégrant les trois mécanismes d'endommagement, la nucléation, la croissance, et la coalescence des cavités. Le modèle d'endommagement intègre les lois de nucléation et de croissance basés sur les phénomènes purement physiques. Ces nouvelles contributions incluant l'influence de l'écrouissage cinématique, ont été validées par les résultats de mesures expérimentales de tomographie à rayon X à haute résolution. Aussi, l'implémentation numérique de l'écrouissage cinématique dans le modèle modifié a contraint de proposer et de réarranger la définition de la triaxialité que l'on trouve habituellement dans la littérature. A coté de cela, un second critère d'initiation à la rupture basé sur l'ultime distance inter-cavités a été inclue afin de localiser et de quantifier avec plus de précision la distribution des déformations peu avant que le matériau ne casse complètement. L'actuel modèle d'endommagement a été appliqué dans des conditions industrielles pour prédire l'évolution de l'endommagement, l'état de contraintes, et l'initiation à la rupture pour différentes géométries de tôles et sur des essais d'emboutissage de tôles minces. / This numerical investigation of an advanced Gurson–Tvergaard–Needleman (GTN) model is an extension of the original work of Ben Bettaieb et al. (2011). The model has been implemented as a user-defined material model subroutine (VUMAT) in the Abaqus/explicit FE code. The current damage model extends the previous version by integrating the three damage mechanisms: nucleation, growth and coalescence of voids. Physically based void nucleation and growth laws are considered, including an effect of the kinematic hardening. These new contributions are based and validated on experimental results provided by high-resolution X-ray absorption tomography measurements. Also, the numerical implementation of the kinematic hardening in this damage extension has obliged to readapt the classical triaxiality definition. Besides, a secondary fracture initiation criterion based on the ultimate average inter-cavities distance has been integrated to localize and quantify with good accuracy the strain distribution just before the material fails apart. The current damage model is applied in industrial conditions to predict the damage evolution, the stress state and the fracture initiation in various tensile thin flat sheet geometries and the cross-die drawing tests.

Konventionelles Laserstrahlschweißen von Halbzeugen aus höherfesten Stahlfeinblechen führt zum drastischen Verlust an Umformbarkeit im Schweißnahtbereich. Durch integrierte induktive Erwärmung können der Temperaturverlauf beim Schweißen modifiziert, die Verbindungseigenschaften beeinflusst und die Umformbarkeit verbessert werden. Die Zusammenhänge zwischen Prozessparametern und mechanischen Verbindungseigenschaften werden beschrieben und Anwendungspotenziale aufgezeigt.

Oriented thermoplastics offer interesting opportunities for making structural automotive components due to their higher strengths. A new process, referred to as the axial feed hot oil tube forming (AF-HOTF) process, has been developed and studied for the forming of oriented thermoplastic tubes. The starting material for AF-HOTF process is an oriented polypropylene (OPP) tube produced by the solid state extrusion process. AF-HOTF was used to study forming and fracture behaviour of OPP tubes at large strains. Mechanical properties and molecular orientation of starting and post-formed materials were investigated to gain a better understanding of structure-property-process relationships during solid state extrusion and subsequent forming of OPP tubes. The development of molecular orientation and other microstructural changes and damage development in extruded and bulged OPP tubes during solid state extrusion and AF-HOTF processes were studied with optical microscopy, wide-angle X-ray diffraction (WAXD) and field emission scanning electron microscope (FE-SEM) techniques. Also, the development of large strains during AF-HOTF of OPP samples were experimentally studied in the form of spatial strain maps, strain/stress state and forming limit strains using an on-line strain mapping method based on digital image correlation (DIC). In addition, tensile tests have been carried out at room temperature on samples machined from the extruded and bulged tubes along the axial and hoop directions. Experimental quantitative relationships amongst molecular orientation parameters and extrusion and AF-HOTF process parameters such as draw ratio, strain and strain state have been obtained. These relationships in the form of White and Spruiell biaxial orientation factors provide a useful insight into molecular reorientation that occurs during extrusion and subsequent forming of OPP tubes. Also, an analytical model for forming limit prediction that takes into account OPP tube properties, tube dimensions and AF-HOTF process parameters was developed based on existing model of tube hydroforming in the literature. In addition, a new biaxial ball stretching test (BBST) system was developed and utilized to subject the thermoplastic tube to biaxial stretching. The design of the test-rig and results were presented for polypropylene (PP) tubes subjected to BBST at various temperatures. The BBST system was combined with an available on-line imaging and strain analysis system (ARAMIS® system from GOM) to observe the development of strains in the biaxial tensile region during the test. BBST samples were studied with wide angle X-ray diffraction (WAXD) pole figures. Three different hot forming processes (Solid-state extrusion, AF-HOTF and BBST) were used in this research. The structure of the extruded samples at draw ratio 5 and higher was completely changed to fibrils structure, and the yield strength and elastic modulus increased by 50%. Also the crystallinity increased from 47% to 68% with an increase in draw ratio. An increase in axial feed during the hot forming process resulted in higher formability (strains values of 0.55 major strain and -0.25 minor strain) and delayed failure. The analytical model prediction of bursting shows good agreement with the experimental results. The results provide an understanding of the orientation development in solid state extrusion of PP tubes as well as an understanding of tube formability, flow localization and fracture characteristics of PP tube from AF-HOTF process and other related processes. / Thesis / Doctor of Philosophy (PhD)

No description available.

With increasing fuel costs and the current drive to reduce greenhouse gas emissions and fuel consumption, a need to reduce vehicle weight is apparent. Weight reduction can be achieved by replacing conventionally stamped structural members with hydroformed parts. The weight reduction can be further enhanced by reducing the thickness of the hydroformed members through the use of advanced high strength steel (AHSS). A primary limitation in hydroforming AHSS, is the limited ductility or formability of these materials. This limitation becomes acute in multi-stage forming operations in which strain path changes become large making it difficult to predict formability. Thus, the focus of the current work is to study the effects of pre-bending on the subsequent hydroformability of Dual-Phase DP600 steel tubes. As part of this effort, the effect of key bending and hydroforming process parameters, bending boost and hydroforming end-feed, have been studied in a parametric fashion. <br /><br /> Multi-step pre-bending and hydroforming experiments were performed on 76. 2 mm (3. 0") OD tubes with a wall-thickness of 1. 85mm (DP600). Experiments were also performed on 1. 74mm Interstitial Free (IF) steel tube, which provided a low strength, high formability baseline material for comparison purposes. A fully instrumented servo-hydraulic mandrel-rotary draw tube bender was used in the pre-bending experiments in which various levels of boost were applied. The results showed that increased boost reduced the major (tensile) strain and thinning at the outside of the bend. At the inside of the bend, the compressive minor strain became larger and thickening increased. <br /><br /> Hydroforming of the straight and pre-bent tubes was conducted using various levels of load-control end-feed (EF). For both straight and pre-bend tube hydroforming, an increase in hydroforming EF resulted in increased burst pressure and corner-fill expansion (CFE). The effect of bending boost on CFE was also measured. For a given hydroforming EF case, a tube bent with greater boost achieved a higher burst pressure and consequently a greater CFE which increased the hydroformability of the material. Pre-bending was shown to consume a considerable amount of the formability of the tube in the hydroforming experiments. For the same EF case, the pre-bent tubes could only achieve a fraction of the straight tube CFE at burst. <br /><br /> The pre-bending and hydroforming experiments were complimented by finite element simulation in the hope of providing additional insight into these processes. The finite element (FE) models were able to accurately predict the strain and thickness changes imposed during pre-bending. The models were able to accurately predict the CFE, EF displacement, and strain and thickness distributions after hydroforming. <br /><br /> The extended stress-based forming limit curve (XSFLC) failure criterion was applied to predict failure (onset of necking) during hydroforming, which was measured as the burst pressure in the experiments. For straight tube hydroforming, the XSFLC predicted the correct failure pressure versus hydroforming EF load trend, but over predicted the failure pressures. In pre-bend hydroforming, the models were able to capture the effect of bending boost and hydroforming EF on the hydroformability of the tubes. The XSFLC was able to capture the drop in formability for bending versus straight tube hydroforming, but was unable to capture the failure pressure versus hydroforming EF load trend or magnitude. Further work is required to make the XSFLC applicable to straight and pre-bend hydroforming.

With increasing fuel costs and the current drive to reduce greenhouse gas emissions and fuel consumption, a need to reduce vehicle weight is apparent. Weight reduction can be achieved by replacing conventionally stamped structural members with hydroformed parts. The weight reduction can be further enhanced by reducing the thickness of the hydroformed members through the use of advanced high strength steel (AHSS). A primary limitation in hydroforming AHSS, is the limited ductility or formability of these materials. This limitation becomes acute in multi-stage forming operations in which strain path changes become large making it difficult to predict formability. Thus, the focus of the current work is to study the effects of pre-bending on the subsequent hydroformability of Dual-Phase DP600 steel tubes. As part of this effort, the effect of key bending and hydroforming process parameters, bending boost and hydroforming end-feed, have been studied in a parametric fashion. <br /><br /> Multi-step pre-bending and hydroforming experiments were performed on 76. 2 mm (3. 0") OD tubes with a wall-thickness of 1. 85mm (DP600). Experiments were also performed on 1. 74mm Interstitial Free (IF) steel tube, which provided a low strength, high formability baseline material for comparison purposes. A fully instrumented servo-hydraulic mandrel-rotary draw tube bender was used in the pre-bending experiments in which various levels of boost were applied. The results showed that increased boost reduced the major (tensile) strain and thinning at the outside of the bend. At the inside of the bend, the compressive minor strain became larger and thickening increased. <br /><br /> Hydroforming of the straight and pre-bent tubes was conducted using various levels of load-control end-feed (EF). For both straight and pre-bend tube hydroforming, an increase in hydroforming EF resulted in increased burst pressure and corner-fill expansion (CFE). The effect of bending boost on CFE was also measured. For a given hydroforming EF case, a tube bent with greater boost achieved a higher burst pressure and consequently a greater CFE which increased the hydroformability of the material. Pre-bending was shown to consume a considerable amount of the formability of the tube in the hydroforming experiments. For the same EF case, the pre-bent tubes could only achieve a fraction of the straight tube CFE at burst. <br /><br /> The pre-bending and hydroforming experiments were complimented by finite element simulation in the hope of providing additional insight into these processes. The finite element (FE) models were able to accurately predict the strain and thickness changes imposed during pre-bending. The models were able to accurately predict the CFE, EF displacement, and strain and thickness distributions after hydroforming. <br /><br /> The extended stress-based forming limit curve (XSFLC) failure criterion was applied to predict failure (onset of necking) during hydroforming, which was measured as the burst pressure in the experiments. For straight tube hydroforming, the XSFLC predicted the correct failure pressure versus hydroforming EF load trend, but over predicted the failure pressures. In pre-bend hydroforming, the models were able to capture the effect of bending boost and hydroforming EF on the hydroformability of the tubes. The XSFLC was able to capture the drop in formability for bending versus straight tube hydroforming, but was unable to capture the failure pressure versus hydroforming EF load trend or magnitude. Further work is required to make the XSFLC applicable to straight and pre-bend hydroforming.

The aim of the Diploma Thesis is to discuss the creation of material models for the forming technology in quasi-static and dynamic loading conditions and to practically propose a methodology of modeling the mechanical behavior of the selected material for dynamic load conditions using the Split Hopkinson Tensile Bar Test. The presented work contains an overview and analysis of individual experimental methods with the influence of the strain rate in terms of the extent of their suitability, the analysis of the plastic deformation mechanism, an overview of the mathematical mechanical behavior models for the materials used for technological practice and the evaluation of the mechanical behavior of stainless steel according to ČSN 41 7348 in terms of flat formability incl. evaluation of microstructure, fractographic analysis and evaluation of results from ferromagnetism measurement of steel after dynamic loading.

No description available.

No description available.

Induction Assisted Single Point Incremental Forming (IASPIF) is a die-less hot sheet metal forming. The IASPIF does not apply characteristic complex tooling like those applied in deep drawing and bending. In this thesis, induction heating was used to heat up the sheet while simultaneously forming with a tool. The research goal is to improve the formability of high strength steels by heating. The IASPIF consists of non-complicated set up that allows induction heating to be utilized through the coil inductor moved under the sheet and synchronized with the forming tool that moves on the upper side of the sheet. The advanced high strength steel alloys, DP980, DP600 and 22MnB5 steels, were investigated. The influence of induction heating on formability was evaluated by the maximum wall angle that can be achieved in a single pass. Additionally, tool diameter and tool feed rate was also varied. The most influencing parameters were tool feed rate, induction power, and the profile depth. A new forming strategy was also developed by control the heating temperature through coupling the formed profile depth with a successively increased tool feed rate. The forming forces of DP980 steel sheet, were reduced from 7 kN to 2.5 kN when forming process was performed at room and elevated temperature, respectively. Stretching stresses were developed during forming process causing a high reduction in the resulting wall part thickness. New findings in this investigation were the reverse relationship between the step-down depth and the thickness reduction percentage. The smaller the tool diameter, the better was the formability. The finite element simulation of the investigated forming process showed that the increase in heating temperature has a direct effect on rising the plastic strain from 0.2 at room temperature to 1.02 at 800 ◦ C. The maximum true strain achieved in the resulting wall part thickness was determined by FEM simulations and validated with experimental trials. The part shape accuracy was measured and the highest deflection was founded when the part was formed by the highest step-down depth. Moreover, the minimum deflection in the part shape was achieved by utilizing a high induction power in the experiments. Finally, the resulting mechanical properties of the 22MnB5 alloy sheet material were tailored during IASPIF. For this purpose, the sheets were locally heated by induction during the forming process and subsequently quenched at different rates. As a result, the produced tailored parts consist of three different regions, which consist of a ductile, transitional and hardened region. The proposed procedure allows forming and quenching at the same time without transfer and thus, process time was reduced. / Die induktionsgestützte, inkrementelle Blechumformung (englisch: Induction Assisted Single-Point Incremental Forming IASPIF) ist Warmumformprozess, bei dem keine komplexen Werkzeuge wie beim Tiefziehen und Biegen benötigt werden. Inhalt dieser Arbeit ist die inkrementelle Umformung eines Bleches mit gleichzeitig ablaufender induktiver Erwärmung. Das Forschungsziel bestand in der Verbesserung der Umformbarkeit von hochfesten Stahlwerkstoffen wie DP600, DP980 und 22MnB5 durch eine gezielte partielle Erwärmung. Der prinzipielle Aufbau des Versuchsstandes besteht aus einem Spuleninduktor, der unterhalb des umzuformenden Blechs platziert ist, und der synchron mit dem Werkzeug – einem Drückdorn – während des Umformvorganges verfährt. Ein wesentlicher Untersuchungsschwerpunkt bestand in der Ermittlung der Einflussgrößen auf den untersuchten IASPIF-Prozess. Für die Bewertung der Umformbarkeit wurden hierbei der maximal erreichbare Teilwandwinkel und die Profiltiefe, die in einem Umformdurchgang herstellbar waren, ermittelt und ausgewertet. Darüber hinaus konnten im Rahmen der Arbeit die Induktionsleistung des Generators, der Werkzeugdurchmesser und die Werkzeugvorschubgeschwindigkeit als relevante Prozessparameter identifiziert werden. Im Ergebnis der durchgeführten Untersuchungen zeigten die Werkzeugvorschubgeschwindigkeit und die Induktionsleistung einen wesentlichen Einfluss auf die erreichbare Profiltiefe. Aufbauend auf den erzielten Ergebnissen konnte eine prozessangepasste Umformstrategie entwickelt werden, bei der eine konstante Erwärmungstemperatur durch das Koppeln der momentanen Profiltiefe mit einer sukzessiv steigenden Werkzeugvorschubgeschwindigkeit erreicht wird. Weiterhin ließen sich die Kräfte bei der Umformung eines Stahlbleches aus DP980 von 7 kN (bei Raumtemperatur) auf 2,5 kN (bei erhöhter Temperatur) reduzieren. Aufgrund des mit einem Streckziehvorgang vergleichbaren Spannungszustandes während des Umformprozesses war eine starke Verringerung der resultierenden Wanddicke zu beobachten. Als neue Erkenntnis in dieser Untersuchung konnte die umgekehrte Beziehung zwischen der Zustelltiefe und dem Dickenreduktionsprozentsatz abgleitet werden. Aus der Finite - Elemente - Simulation des vorgestellten Umformprozesses wurde erkennbar, dass die Erhöhung der Erwärmungstemperatur einen direkten Einfluss auf die plastische Dehnung von 0,2 (bei Raumtemperatur) auf 1,02 (bei 800 °C) hat. Mittels der numerischen Simulation und der nachfolgenden experimentellen Validierung erfolgte darüber hinaus die Bestimmung der maximalen wahren Dehnung, die in der resultierenden Wanddicke erreicht wurde. Bei den Versuchen mit der größten Zustellung ließ sich durch die Bestimmung der Teileformgenauigkeit die höchste Abweichung von der Sollgeometrie CAD Modell feststellen. Abschließend wurde nachgewiesen, dass der IASPIF Prozess auch zur Einstellung maßgeschneiderter Bauteileigenschaften wie der resultierenden mechanischen Eigenschaften des Blechmaterials aus 22MnB5 einsetzbar ist. Zu diesem Zweck wurden die Bleche während des Umformprozesses lokal induktiv erwärmt und anschließend zur Einstellung des gewünschten Gefüges bei unterschiedlichen Abkühlgeschwindigkeiten abgeschreckt.