No description available.

No description available.

No description available.

A multidisciplinary design optimization (MDO) methodology is developed to link the aerodynamic shape design to the system costs for magnetically levitated (MAGLEV) vehicles. These railed vehicles can cruise at speeds approaching that of short haul aircraft and travel just inches from a guideway. They are slated for high speed intercity service of up to 500 miles in length and would compete with air shuttle services. The realization of this technology hinges upon economic viability which is the impetus for the design methodology presented here. This methodology involves models for the aerodynamics, structural weight, direct operating cost, acquisition cost, and life cycle cost and utilizes the DOT optimization software. Optimizations are performed using sequential quadratic programming for a 5 design variable problem. This problem is reformulated using 7 design variables to overcome problems due to non-smooth design space. The reformulation of the problem provides a smoother design space which is navigable by calculus based optimizers. The MDO methodology proves to be a useful tool for the design of MAGLEV vehicles. The optimizations show significant and sensible differences between designing for minimum life cycle cost and other figures of merit. The optimizations also show a need for a more sensitive acquisition cost model which is not based simply on weight engineering. As a part of the design methodology, a low-order aerodynamics model is developed for the prediction of 2-D, ground effect flow over bluff bodies. The model employs a continuous vortex sheet to model the solid surface, discrete vortices to model the shed wake, the Stratford Criterion to determine the location of the turbulent separation, and the vorticity conservation condition to determine the strength of the shed vorticity. The continuous vortex sheet better matches the mechanics of the flow than discrete singularities and therefore better predicts the ground effect flow. The predictions compare well with higher-order computational methods and experimental data. A 3-D extension to this model is investigated, although no 3-D design optimizations are performed. NOTE: An updated copy of this ETD was added on 05/29/2013. / Ph. D.

No description available.

This research focuses on the study of the behavior of a high speed vehicle and particularly an air-cushion vehicle (ACV) in varying bathymetry. An extensive data acquisition system is developed to gather data during the experiments. Four groups of experiments are conducted in a wave tank using a scale model surface effect ship to generate a database that is post processed to assess phenomena under various conditions. Group No1 experiments involved characterizing the wave motion in the tank in the absence of the vehicle as the waves transformed in response to variation in water depth. Based on these experimental datasets, the wave breaking type and position are predicted using a machine learning approach and, more specifically, a neural network of the multilayer perceptron type. Group No2 experiments are in support of a parametric study to evaluate the vehicle's performance under calm water conditions when the control inputs are varied. A system identific ation approach based on the experimental data is proposed to create a model that predicts the vehicles translational motion. In group No3 the experiments involve the vehicle travelling with a non-zero forward speed and encountering transforming head and following seas. Transient and non-linear phenomena and relations among parameters are observed Group No 4 experiments involve the vehicle maintaining a position in the "surf-zone" under manual control, encountering breaking waves that break on its bow skirt. Non-linear phenomena are discussed based on the experimental results. / Includes bibliography. / Dissertation (Ph.D.)--Florida Atlantic University, 2015. / FAU Electronic Theses and Dissertations Collection

Thesis. 1977. Sc.D.--Massachusetts Institute of Technology. Dept. of Mechanical Engineering. / MICROFICHE COPY AVAILABLE IN ARCHIVES AND ENGINEERING. / Includes bibliographical references. / Sc.D.

Aerodynamic devices, such as wings, are used in higher levels of motorsport (Formula-1 etc.) to increase the contact force between the road and tyres (i.e. to generate downforce). This in turn increases the performance envelope of the race car. However the extra downforce increases aerodynamic drag which (apart from when braking) is generally detrimental to lap-times. The drag acts to slow the vehicle, and hinders the effect of available drive power and reduces fuel economy. Wings, in automotive use, are not constrained by the same parameters as aircraft, and thus higher angles of attack can be safely reached, although at a higher cost in drag. Variable geometry aerodynamic devices have been used in many forms of motorsport in the past offering the ability to change the relative values of downforce and drag. These have invariably been banned, generally due to safety reasons. The use of active aerodynamics is currently legal in both Formula SAE (engineering compet ition for university students to design, build and race an open-wheel race car) and production vehicles. A number of passenger car companies are beginning to incorporate active aerodynamic devices in their designs. In this research the effect of ground proximity on the lift, drag and moment coefficients of inverted, two-dimensional aerofoils was investigated. The purpose of the study was to examine the effect ground proximity on aerofoils post stall, in an effort to evaluate the use of active aerodynamics to increase the performance of a race car. The aerofoils were tested at angles of attack ranging from 0° - 135°. The tests were performed at a Reynolds number of 2.16 x 105 based on chord length. Forces were calculated via the use of pressure taps along the centreline of the aerofoils. The RMIT Industrial Wind Tunnel (IWT) was used for the testing. Normally 3m wide and 2m high, an extra contraction was installed and the section was reduced to form a width of 295mm. The wing was mounted between walls to simulate 2-D flow. The IWT was chosen as it would allow enough height to reduce blockage effect caused by the aerofoils when at high angles of incidence. The walls of the tunnel were pressure tapped to allow monitoring of the pressure gradient along the tunnel. The results show a delay in the stall of the aerofoils tested with reduced ground clearance. Two of the aerofoils tested showed a decrease in Cl with decreasing ground clearance; the third showed an increase. The Cd of the aerofoils post-stall decreased with reduced ground clearance. Decreasing ground clearance was found to reduce pitch moment variation of the aerofoils with varied angle of attack. The results were used in a simulation of a typical Formula SAE race car.

Aircraft manufacturer Aquavion Systems is currently designing and constructing prototypes for its revolutionary new fleet of aircraft called the SeaStryder. During the prototyping phase, it was discovered that the center-of-gravity of the SeaStryder600 was too far aft and outside of the acceptable range. To solve this design issue, it was hypothesized that the weight of the horizontal stabilizer may be reduced without compromising its structural integrity. The following document analyzes this hypothesis and provides two alternative designs. Each design exceeds the design requirements, meets additional requirements requested by industry, and provides a significant degree of weight savings. The first design provides a 25% weight reduction. The second design provides an 18% weight reduction as well as a 160% increase in loading capacity. The designs proposed have both been verified through the use of Finite Element Analysis as well as by means of experimentation where two prototype wings were constructed and tested to failure confirming the analytical results.

Aircraft manufacturer Aquavion Systems is currently designing and constructing prototypes for its revolutionary new fleet of aircraft called the SeaStryder. During the prototyping phase, it was discovered that the center-of-gravity of the SeaStryder600 was too far aft and outside of the acceptable range. To solve this design issue, it was hypothesized that the weight of the horizontal stabilizer may be reduced without compromising its structural integrity. The following document analyzes this hypothesis and provides two alternative designs. Each design exceeds the design requirements, meets additional requirements requested by industry, and provides a significant degree of weight savings. The first design provides a 25% weight reduction. The second design provides an 18% weight reduction as well as a 160% increase in loading capacity. The designs proposed have both been verified through the use of Finite Element Analysis as well as by means of experimentation where two prototype wings were constructed and tested to failure confirming the analytical results.