>Magister Scientiae - MSc / Electrochemical platforms were developed based on pencil graphite electrodes (PGEs) modified with electrochemically deposited graphene (EG) sheets and Nafion-graphene (NG) nanocomposites in conjunction with an in situ plated bismuth-film (EG-PG-BiE and NG-PG-BiE). The EG- and NG-PG-BiEs were used as sensing platforms for determining Zn2+, Cd2+ and Pb2+ by square wave anodic stripping voltammetry (SWASV). EG sheets were deposited onto pencil graphite electrodes by cyclic voltammetric reduction from a graphene oxide (GO) solution, while a dip coating method was used to prepare the NG-PG-BiE. The GO and graphene, with flake thicknesses of 1.78 (2 sheets) and 2.10 nm (5 sheets) respectively, was characterized using FT-IR, HR-SEM, HR-TEM, AFM, XRD and Raman spectroscopy. Parameters influencing the electroanalytical response of the EG-PG-BiE and NG-PG-BiE such as, bismuth ion concentration, deposition potential, deposition time and rotation speed were investigated and optimized. The EG-PG-BiE gave well-defined, reproducible peaks with detection limits of 0.19 μg L-1, 0.09 μg L-1 and 0.12 μg L-1 for Zn2+, Cd2+ and Pb2+ respectively, at a deposition time of 120 seconds. The NG-PG-BiE showed similar detection limits of 0.167 μg L-1, 0.098 μg L-1 and 0.125 μg L-1 for Zn2+, Cd2+ and Pb2+ respectively. For real sample analysis, the enhanced voltammetric sensor proved to be suitable for the detection and quantitation of heavy metals below the US EPA prescribed drinking water standards of 5 mg L-1, 5 μg L-1 and 15 μg L-1 for Zn2+, Cd2+ and Pb2+ respectively.

No description available.

No description available.

Magister Scientiae - MSc (Chemistry) / In this study, graphene oxide was synthesized by oxidizing graphite using the modified Hummer's method. The graphene oxide was characterized by Raman Spectroscopy, Fourier Transform Infrared Spectroscopy, High Resolution Transmission Electron Microscopy, Scanning Electron Microscopy and X-Ray Diffraction for structural and morphological properties. The graphene oxide was electrochemically reduced on a carbon paste electrode followed by the in situ deposition of mercury thin films to achieve electrochemically reduced graphene oxide modified carbon paste metal film electrodes (ERGO-CP-MEs). The experimental parameters (amplitude, deposition time, deposition potential, frequency and rotation speed) were optimized, and the applicability of the modified electrode was investigated towards the simultaneous and individual determination of TI1+ and In3+ at the low concentration levels (?g L-1) in 0.1 M acetate buffer (pH 4.6) using square wave anodic stripping voltammetry (SWASV). The detection limit values for individual analysis at electrochemically reduced graphene oxide modified carbon paste mercury film electrode (ERGO-CP-HgE ) was 2.4 and 1.1 ?g L-1 for TI1+ and In3+, respectively. The detection limit values for simultaneous analysis at ERGO-CPE was 1.32 and 1.33 ?g L-1 and individual analysis was 0.975 and 1.04 ?g L-1 for TI1+ and In3+, respectively.

This study reports the synthesis of graphene by oxidizing graphite to graphite oxide using H2SO4 and KMnO4 and reducing graphene oxide to graphene by using NaBH4. Graphene was then characterized using FT-IR, TEM, AFM, XRD, Raman spectroscopy and solid state NMR. Nafion-Graphene in combination with a mercury film electrode, bismuth film electrode and antimony film electrode was used as a sensing platform for trace metal analysis in 0.1 M acetate buffer (pH 4.6) at 120 s deposition time, using square-wave anodic stripping voltammetry (SWASV). Detection limits were calculated using 3σblank/slope. For practical applications recovery studies was done by spiking test samples with known concentrations of metal ions and comparing the results to inductively coupled plasma mass spectrometry (ICPMS). This was then followed by real sample analyses.

This study reports the synthesis of graphene by oxidizing graphite to graphite oxide using H2SO4 and KMnO4 and reducing graphene oxide to graphene by using NaBH4. Graphene was then characterized using FT-IR, TEM, AFM, XRD, Raman spectroscopy and solid state NMR. Nafion-Graphene in combination with a mercury film electrode, bismuth film electrode and antimony film electrode was used as a sensing platform for trace metal analysis in 0.1 M acetate buffer (pH 4.6) at 120 s deposition time, using square-wave anodic stripping voltammetry (SWASV). Detection limits were calculated using 3σblank/slope. For practical applications recovery studies was done by spiking test samples with known concentrations of metal ions and comparing the results to inductively coupled plasma mass spectrometry (ICPMS). This was then followed by real sample analyses.

Magister Scientiae - MSc (Dept. of Chemistry) / This study reports the synthesis of graphene by oxidizing graphite to graphite oxide using H2SO4 and KMnO4 and reducing graphene oxide to graphene by using NaBH4. Graphene was then characterized using FT-IR, TEM, AFM, XRD, Raman spectroscopy and solid state NMR. Nafion-Graphene in combination with a mercury film electrode, bismuth film electrode and antimony film electrode was used as a sensing platform for trace metal analysis in 0.1 M acetate buffer (pH 4.6) at 120 s deposition time, using square-wave anodic stripping voltammetry (SWASV). Detection limits were calculated using 3σblank/slope. For practical applications recovery studies was done by spiking test samples with known concentrations of metal ions and comparing the results to inductively coupled plasma mass spectrometry (ICPMS). This was then followed by real sample analyses. / South Africa

The accurate and rapid detection of clinically relevant analytes at the point-of-care (POC) is a crucial element for the increase in our quality of life. There are multiple detection techniques for sensing a target analyte in biological samples. However, electrochemical sensors excel because of their versatility, accuracy and sensitivity. Among the many challenges in the fabrication of electrochemistry-based POC sensors, the miniaturization of the working electrodes is one of the most difficult to overcome. Decreasing the size of the sensors will result in less electroactive surface area (ESA) and, therefore, lower sensitivity. Thus, the design of miniaturized electrodes with high ESA is desired in this research field. The methodology developed in our laboratory to accomplish this goal is based on the fabrication of microstructured gold electrodes (MSEs) by depositing, via sputtering, a gold thin-film onto a pre-stressed polystyrene substrate masked with adhesive vinyl stencils and thermally shrinking the substrate at high temperatures (135-160 °C). In my thesis work, I developed cost-effective sensitive electrochemical platforms using only bench-top approaches. First, the ESA and, thus, the sensitivity of the MSEs were enhanced by using a simple and rapid nano-roughening approach. The ESA of MSEs was increased 4x by applying high voltage pulsing in sulfuric acid. The resulting electrodes possessed high anti-fouling capabilities and excellent response toward the enzyme-free detection of glucose with a limit of detection (LOD) of 0.62 mM in the presence of bovine serum albumin (BSA) and ascorbic acid. Furthermore, the fabrication cost of the MSEs electrodes was decreased by 5x by replacing the sputtering deposition step with a cost-effective solution-based electroless deposition technique. In this case, the PS substrates were coated with a polydopamine adhesion layer and noble metal films (copper, silver and gold) were subsequently plated. Not only the cost of the gold electrode was substantially reduced but, due to the intrinsic roughness of the surface, the MSEs electrodes obtained via electroless deposition showed a higher ESA than those made via sputtering. Furthermore, the developed electroless method was extended for the fabrication of paper-based sensing devices. The sensing versatility of these surfaces was demonstrated by electrochemically detecting mercury with a 0.27 ppb LOD and by sensing thiophenol via surface-enhanced Raman scattering (SERS). The MSEs electrodes fabricated via electroless deposition were subjected to the nano-roughening technique to generate affordable and high ESA electrodes. These platforms were used to design enzyme-based biosensors to accurately detect glucose and urea in complex samples. Glucose was detected in four different types of wine, with matrix interference measured below 10%, and in human serum, with a measured concentration that was not statistically different from that obtained from commercially available biosensors. Urea was detected in human urine and plasma with matrix interferences measured to be below 8% in both cases. We envision that the fabrication techniques developed in this thesis will rapidly grow in the scientific community for the prompt and accurate design of POC electrochemical devices. / Thesis / Doctor of Philosophy (PhD)

Gegenstand der vorliegenden Arbeit ist die Synthese und Charakterisierung neuer chromophorer Catecholderivate mit ausgeprägten push-pull-pi-Systemen. Die solvatochromen Eigenschaften dieser Verbindungen werden in Abhängigkeit der Wasserstoffbrückenbindungsdonor- und -akzeptorfähigkeit sowie Lösungsmitteldipolarität diskutiert. Mit entsprechenden methoxy- und dimethoxyfunktionalisierten Catecholderivaten ist es möglich, vergleichende Struktur-Eigenschaftsbeziehungen aufzustellen. Durch Untersuchungen zu den Wechselwirkungen der chromophoren Catechole mit Schwermetallionen kann gezeigt werden, dass die synthetisierten Verbindungen als Sensoren eingesetzt werden können. In der vorliegenden Arbeit wird des Weiteren die Adsorption der Catecholderivate an Metalloxide beschrieben. Mit Farbstoffen sensibilisierte Oberflächen stellen derzeit ein interessantes Forschunggebiet dar. Ferner wird über die Umsetzung der Catecholderivate mit Trialkoxysilanen zu zwitterionischen, spirozyklischen, pentakoordinierten lambda5Si-Silicaten sowie mit Tetraalkoxysilanen zu dianionischen, hexakoordinierten lambda6Si-Silicaten berichtet. Besonderes Augenmerk lag dabei auf UV/vis-spektroskopischen Untersuchungen.

Gegenstand der vorliegenden Arbeit ist die Synthese und Charakterisierung neuer chromophorer Catecholderivate mit ausgeprägten push-pull-pi-Systemen. Die solvatochromen Eigenschaften dieser Verbindungen werden in Abhängigkeit der Wasserstoffbrückenbindungsdonor- und -akzeptorfähigkeit sowie Lösungsmitteldipolarität diskutiert. Mit entsprechenden methoxy- und dimethoxyfunktionalisierten Catecholderivaten ist es möglich, vergleichende Struktur-Eigenschaftsbeziehungen aufzustellen. Durch Untersuchungen zu den Wechselwirkungen der chromophoren Catechole mit Schwermetallionen kann gezeigt werden, dass die synthetisierten Verbindungen als Sensoren eingesetzt werden können. In der vorliegenden Arbeit wird des Weiteren die Adsorption der Catecholderivate an Metalloxide beschrieben. Mit Farbstoffen sensibilisierte Oberflächen stellen derzeit ein interessantes Forschunggebiet dar. Ferner wird über die Umsetzung der Catecholderivate mit Trialkoxysilanen zu zwitterionischen, spirozyklischen, pentakoordinierten lambda5Si-Silicaten sowie mit Tetraalkoxysilanen zu dianionischen, hexakoordinierten lambda6Si-Silicaten berichtet. Besonderes Augenmerk lag dabei auf UV/vis-spektroskopischen Untersuchungen.