No description available.

Indium tin oxide (ITO) and molybdenum are substrates of choice in the manufacture of the CdS-CIS photovoltaic cell, which is the base for the leading thin-film solar cell technology. Substantial advancement in this technology is expected if these devices can be made in nanoporous alumina (AAO) templates. The first step to this endeavor is to learn to form AAO templates on molybdenum and ITO substrates. This was accomplished, and the results are reported in this thesis. Starting substrates were glass, coated with either a thin molybdenum layer or a thin ITO layer. Aluminum was deposited on top of this conducting substrate. Oxalic acid was used as the electrolyte for anodization. In the case of molybdenum substrates, average pore diameter was 45 nm when an anodization voltage of 40 volts was used for approximately 46 minutes; current density was approximately 23 amps/sq. m. In the case of ITO substrates, pores of 45 nm diameter were obtained for approximately 20 minute anodization at 40 V; current density was 40 amps/sq. m; annealing of aluminum layer prior to anodization, at 550 oC (degrees Centigrade) for 90 minutes was needed to obtain good pores. A one micrometer thick CdS layer was electrodeposited inside the AAO pores on top of the ITO substrate. In preliminary experiments, CdS/Cu2S photovoltaic heterojunctions with an open circuit voltage of 242 mV were formed inside the nanopores.

Organic solar cells are cheaper and much easier to fabricate than the conventional inorganic solar cells, but they suffer from low efficiencies due to low carrier mobilities in organic films. In this study Copper Phthalocyanine (CuPc) and Buckminster Fullerene (C60) based Schottky diodes were fabricated on ITO coated glass substrates to study their performance and a study of the effect of thickness on the cell parameters of CuPc Schottky diodes was made. Also, TiO2 based devices were studied to see the effect of TiO2 layer on the cell parameters. The J-V curves were analyzed for series resistance, diode ideality factor and reverse saturation current density. The devices were also characterized by SEM and XRD measurements.

Dissertation (Ph.D.)--Auburn University, 2005. / Abstract. Vita. Includes bibliographic references.

abstract: A primary motivation of research in photovoltaic technology is to obtain higher efficiency photovoltaic devices at reduced cost of production so that solar electricity can be cost competitive. The majority of photovoltaic technologies are based on p-n junction, with efficiency potential being much lower than the thermodynamic limits of individual technologies and thereby providing substantial scope for further improvements in efficiency. The thesis explores photovoltaic devices using new physical processes that rely on thin layers and are capable of attaining the thermodynamic limit of photovoltaic technology. Silicon heterostructure is one of the candidate technologies in which thin films induce a minority carrier collecting junction in silicon and the devices can achieve efficiency close to the thermodynamic limits of silicon technology. The thesis proposes and experimentally establishes a new theory explaining the operation of silicon heterostructure solar cells. The theory will assist in identifying the optimum properties of thin film materials for silicon heterostructure and help in design and characterization of the devices, along with aiding in developing new devices based on this technology. The efficiency potential of silicon heterostructure is constrained by the thermodynamic limit (31%) of single junction solar cell and is considerably lower than the limit of photovoltaic conversion (~ 80 %). A further improvement in photovoltaic conversion efficiency is possible by implementing a multiple quasi-fermi level system (MQFL). A MQFL allows the absorption of sub band gap photons with current being extracted at a higher band-gap, thereby allowing to overcome the efficiency limit of single junction devices. A MQFL can be realized either by thin epitaxial layers of alternating higher and lower band gap material with nearly lattice matched (quantum well) or highly lattice mismatched (quantum dot) structure. The thesis identifies the material combination for quantum well structure and calculates the absorption coefficient of a MQFl based on quantum well. GaAsSb (barrier)/InAs(dot) was identified as a candidate material for MQFL using quantum dot. The thesis explains the growth mechanism of GaAsSb and the optimization of GaAsSb and GaAs heterointerface. / Dissertation/Thesis / Ph.D. Electrical Engineering 2011

The ability to form multiple component heterostructures of two-dimensional materials promises to provide access to hybrid materials with tunable properties different from those of the bulk materials or two-dimensional constituents. By taking advantage of the unique properties of different constituents, numerous applications are possible for which none of the individual components are viable. The synthesis of multiple component heterostructures, however, is nontrivial, relying on either the cleaving and stacking of bulk materials in a “scotch tape” type technique or finding coincidentally favorable growth conditions which allow layers to be grown epitaxially on each other in any order. In addition, alloying of miscible materials occurs when the modulation wavelength is small. These synthetic challenges have limited the ability of scientists to fully utilize the potential of multiple component heterostructures. An alternative synthetic route to multiple component heterostructures may be found through expansion of the modulated elemental reactant technique which allows access to metastable products, known as ferecrystals, which are otherwise inaccessible. This work focuses on the expansion of the modulated elemental reactants technique for the formation of ferecrystals containing multiple constituents. As a starting point, the synthesis of the first alloy ferecrystals (SnSe)1.16-1.09([NbxMo1-x]Se2) will be discussed. The structural and electrical characterization of these compounds will then be used to determine the intermixing of the first three component ferecrystal heterojunction ([SnSe]1+δ)([{MoxNb1-x}Se2]1+γ)([SnSe]1+δ)({NbyMo1-y}Se2). Then, by synthesizing ([SnSe]1+δ)m([{MoxNb1-x}Se2]1+γ)1([SnSe]1+δ)m({NbxMo1-x}Se2)1 (m = 0 - 4) compounds with increasing thicknesses of SnSe, the interdiffusion of miscible constituents in ferecrystals will be studied. In addition, by comparison of the ([SnSe]1+δ)m ([{MoxNb1-x}Se2]1+γ)1([SnSe]1+δ)m({NbxMo1-x}Se2)1 (m = 0 - 4) compounds to the ([SnSe]1+δ)m(NbSe2)1 (m = 1 - 8) compounds the electronic interactions of the MoSe2 and NbSe2 layers will be determined. Finally, the effects of different alloying strategies and the interdiffusion of miscible constituents will be further examined by the synthesis of ordered ([SnSe]1.15)1([TaxV1-x]Se2)1([SnSe]1.15)1([VyTa1-y]Se2)1 and ([SnSe]1+δ) ([TaxV1-x]Se2) compounds with the effect of isoelectric doping on the charge density wave transition in (SnSe)1.15(VSe2) also being explored. This work contains previously published and unpublished co-authored material.

abstract: Layers of intrinsic hydrogenated amorphous silicon and amorphous silicon carbide were prepared on a polished, intrinsic crystalline silicon substrate via plasma-enhanced chemical vapor deposition to simulate heterojunction device relevant stacks of various materials. The minority carrier lifetime, optical band gap and FTIR spectra were observed at incremental stages of thermal annealing. By observing the changes in the lifetimes the sample structure responsible for the most thermally robust surface passivation could be determined. These results were correlated to the optical band gap and the position and relative area of peaks in the FTIR spectra related to to silicon-hydrogen bonds in the layers. It was found that due to an increased presence of hydrogen bonded to silicon at voids within the passivating layer, hydrogenated amorphous silicon carbide at the interface of the substrate coupled with a hydrogenated amorphous silicon top layer provides better passivation after high temperature annealing than other device structures. / Dissertation/Thesis / Masters Thesis Electrical Engineering 2016

abstract: Silicon solar cells with heterojunction carrier collectors based on a-Si/c-Si heterojunction (SHJ) have a potential to overcome the limitations of the conventional diffused junction solar cells and become the next industry standard manufacturing technology of solar cells. A brand feature of SHJ technology is ultrapassivated surfaces with already demonstrated 750 mV open circuit voltages (Voc) and 24.7% efficiency on large area solar cell. Despite very good results achieved in research and development, large volume manufacturing of high efficiency SHJ cells remains a fundamental challenge. The main objectives of this work were to develop a SHJ solar cell fabrication flow using industry compatible tools and processes in a pilot production environment, study the interactions between the used fabrication steps, identify the minimum set of optimization parameters and characterization techniques needed to achieve 20% baseline efficiency, and analyze the losses of power in fabricated SHJ cells by numerical and analytical modeling. This manuscript presents a detailed description of a SHJ solar cell fabrication flow developed at ASU Solar Power Laboratory (SPL) which allows large area solar cells with >750 mV Voc. SHJ cells on 135 um thick 153 cm2 area wafers with 19.5% efficiency were fabricated. Passivation quality of (i)a-Si:H film, bulk conductivity of doped a-Si films, bulk conductivity of ITO, transmission of ITO and the thickness of all films were identified as the minimum set of optimization parameters necessary to set up a baseline high efficiency SHJ fabrication flow. The preparation of randomly textured wafers to minimize the concentration of surface impurities and to avoid epitaxial growth of a-Si films was found to be a key challenge in achieving a repeatable and uniform passivation. This work resolved this issue by using a multi-step cleaning process based on sequential oxidation in nitric/acetic acids, Piranha and RCA-b solutions. The developed process allowed state of the art surface passivation with perfect repeatability and negligible reflectance losses. Two additional studies demonstrated 750 mV local Voc on 50 micron thick SHJ solar cell and < 1 cm/s effective surface recombination velocity on n-type wafers passivated by a-Si/SiO2/SiNx stack. / Dissertation/Thesis / Ph.D. Electrical Engineering 2013

In the last decade, organic photovoltaics (OPVs) have been attracting much attention for their low cost, and feasibility of mass production in large-area modules. Reported power conversion efficiencies (PCE) of organic solar cells have reached more than 10%. These promising PCEs can be realized by uncovering important principles: (1) rational molecular design, (2) matching of the material energy level, (3) favorable morphology of donor-acceptor (D/A) network, (4) higher carrier mobilities, and (5) suppression of charge recombination within the bulk heterojunction (BHJ). Though these key properties are frequently stated, the relationships between these principles remain unclear, which motivates us to fill these gaps. In the beginning, we show that changing the sequence of donor and acceptor units of the benzodithiophene-core (BDT) SM donors critically impacts molecular packing and charge transport in BHJ solar cells. Moreover, we find out that by adding small amount of the external solvent additive, the domain size of the SMFQ1 become relatively smaller, resulting in the FF enhancement of ~70% and thus pushing PCE to >6.5%. To further improve the device performance, we utilize another technique of device optimization: Solvent Vapor Annealing (SVA). Compared with solvent additive, the SVA creates a solvent-saturated environment for SMs to re-arrange and crystalize, leading to PCE of >8%, with nearly-free bimolecular recombination. When the systems are shifted from fullerene acceptors to nonfullerene acceptors, using solvent additives in indacenodithiophene-core (IDT) systems significantly reduces the domain size from >500nm to <50nm and also allows the SM donors to orderly packed, rising the PCE from <1% to 4.5%. Furthermore in a similar IDT-based system, it shows unexpectedly high VOC and low energy loss, and high PCE > 6% can be reached by employing the dimethyl disulfide (DMDS) as the SVA solvent to re-organize the morphology from excessive mixing to ordered phase-separated D/A network. Lastly, taking advantage of the distinct and complementary absorption of fullerene and nonfullerene acceptors, we show that the SM ternary system successfully realizes the high PCE of 11%, good air stability, and scalable property.

Two-dimensional (2D) layered materials such as MoS2 have been recognized as high on-off ratio semiconductors which are promising candidates for electronic and optoelectronic devices. In addition to the use of individual 2D materials, the accelerated field of 2D heterostructures enables even greater functionalities. Device designs differ, and they are strongly controlled by the electronic band alignment. For example, photovoltaic cells require type II heterostructures for light harvesting, and light-emitting diodes benefit from multiple quantum wells with the type I band alignment for high emission efficiency. The vertical tunneling field-effect transistor for next-generation electronics depends on nearly broken-gap band alignment for boosting its performance. To tailor these 2D layered materials toward possible future applications, the understanding of 2D heterostructure band alignment becomes critically important. In the first part of this thesis, we discuss the band alignment of 2D heterostructures. To do so, we firstly study the interlayer coupling between two dissimilar 2D materials. We conclude that a post-anneal process could enhance the interlayer coupling of as-transferred 2D heterostructures, and heterostructural stacking imposes similar symmetry changes as homostructural stacking. Later, we precisely determine the quasi particle bandgap and band alignment of the MoS2/WSe2 heterostructure by using scan tunneling microscopy/spectroscopy (STM/S) and micron-beam X-ray photoelectron spectroscopy (μ-XPS) techniques. Lastly, we prove that the band alignment of 2D heterojunctions can be accurately predicted by Anderson’s model, which has previously failed to predict conventional bulk heterostructures. In the second part of this thesis, we develop a new Chemical Vapor Deposition (CVD) method capable of precisely controlling the growth area of p- and n-type transition metal dichalcogenides (TMDCs) and further form lateral or vertical 2D heterostructures. This method also allows p- and n-type TMDCs to separately grow in a selective area in one step. In addition, we demonstrate a first bottom-up 2D complementary inverter based on hetero-TMDCs.