Compaction of polymer powders and polymer-based nanocomposites by uniaxial high-velocity cold compaction (HVC), by high-energy ball milling (HEBM) and using a novel technique, relaxation assists, was investigated with a focus on the process parameters, the compactibility characteristics, surface morphology and friction. The basic phenomena associated with HVC are explained and the general energy principle is introduced to explain the pull-out phenomenon, springback gradient, delay time, relative time of the pressure wave, and stick-slip phenomenon during the compaction process. Experimental results for different compaction profiles, different particle size distributions and different milling system for polymer-based nanocomposite are presented, showing the effect of varying the process parameters on the compacted material; the compactibility in the compacted bed, the uniformity of the compacted surface, the pull-out phenomenon, the springback gradient, the stick-slip phenomenon and the homogeneity of the dispersions of nanoparticles in the polymer powders in the solid state. It was found that the high-velocity compaction process is an interruption process and that the opposite velocity and pressure loss during the compaction process have a major influence on the quality of the compacted material. The relaxation assist device is a novel technique that has been successfully developed to improve the compaction process. The relaxation assists are parts of the piston and they are regarded as projectile supports. They are constructed of the same material as the piston, and the diameters are the same but the lengths are different. The relaxation assist device leads to an improvement in the compaction of powders, polymer powders and polymer-based nanocomposites by giving a more homogeneous opposite velocity and a better locking of the powder bed in the compacted form during the compaction process with less change in dimensions in the case of both homogeneous and heterogeneous materials. If the movement of the particles is restricted the powder bed attains a higher density and the total elastic springback is minimized. In addition, there is a more homogeneous dispersion of nanoparticles in the case of a heterogeneous material. A much better transfer of the pressure through the powder bed and a smaller loss of pressure lead to a more homogenous stick-slip of the particles and a higher sliding coefficient due to the overall friction during the compaction process. / QC 20100630

<p>A uniaxial High-Velocity Compaction (HVC) process for polymer powder using a cylindrical, hardened steel die and a new technique with relaxation assist was tested with a focus on the compactibility characteristics and surface morphology of the compacted materials using various heights of relaxation assist device with different compacting profiles.</p><p>Relaxation assist device was presented as a new technique to reduce springback, pull-out phenomenon and to improve the compaction process.</p><p>The basic phenomena associated with HVC are explained and the general energy principle is introduced to explain pull-out phenomenon during the decompacting stage. In this study, polyamide-11 powders with different particle size distributions have been compacted with the application of different compaction profiles, e.g. different energies and velocities. It was found that the relative green density is influenced more by the pre-compacting (primary compaction step) than by the post-compacting (secondary compaction step).</p><p>Experimental results for different compaction profiles were presented showing the effect of varying the opposite velocity during the decompacting stage and how to improve the homogeneous densification between the upper and lower surface and the evenness of the upper surface of the compacted powder bed by using relaxation assists, and the influences of the relaxation assist device on the process characteristics. It was found that the relaxation assist improves the compaction of the polymer powder by locking the powder bed in the compacted form. In addition, the relative times of the compacting stage, decompacting stage and the reorganisation of the particles can be controlled by altering the height of the relaxation assist. It was found that the high-velocity compaction process is an interruption process and that the delay times between the pressure waves can be reduced by increasing the height of the relaxation assist device. Furthermore, the first gross instantaneous springback and the total elastic springback are reduced.</p><p>Two bonding strain gauges and a high-speed video camera system were used to investigate the springback phenomenon during the compaction process. Scanning electron microscopy (SEM) and image computer board Camera (IC-PCI Imaging Technology) were used to the study the morphological characteristics, the limit of plastic deformation and particle bonding by plastic flow at contact points, and pull-out phenomena.</p> / QC 20100506

Elasto-plastic shock waves in high-velocity compaction of spherical metal particles are the focus of this thesis which consists of four papers (A-D). The compaction process is modeled by a discrete element method while using elastic and plastic loading, elastic unloading and adhesion at contacts. Paper A investigates the dynamic compaction of a one-dimensional chain of homogenous particles. The development of the elasto-plastic shock waves, its propagation and influence on the compaction process are examined. Simulations yield information on the contact behavior, velocity of the particle and its deformation during dynamic compaction. Effects of changing loading parameters on the compaction process are also discussed. Paper B addresses the non-homogeneity in a chain having; particles of different sizes and materials, voids between the particles and particles with/without adhesion between them. Simulations show transmission and reflection of elasto-plastic shock wave during compaction process. The particle deformation during incident and reflected shocks and particle velocity fluctuations due to voids between particles are simulated. The effects of adhesion on particles separation during unloading stage are also discussed. Paper C develops a simulation model for a high-velocity compaction process with auxiliary pistons, known as relaxation assists, in a compaction assembly. The simulation results reveals that the relaxation assists offer; smooth compaction during loading stage, prevention of  the particle separation during unloading stage and conversion of  higher kinetic energy of hammer into particles deformation.  Furthermore, the influence of various loading elements on compaction process is investigates. These results support the findings of experimental work. Paper D further extends the one-dimensional case of Paper A and B into two-dimensional assembly of particles while adding friction between particles and between particles and container walls. Three particular cases are investigated including closely packed hexagonal, loosely packed random and a non-homogenous assembly of particles of various sizes and materials. Consistent with the one-dimensional case, primary interest is the linking of particle deformation with the elasto-plastic shock wave propagation. Simulations yield information on particle deformation during shock propagation and change in overall particles compaction with the velocity of the hammer. The force exerted by particles on the container walls and rearrangement of the loosely packed particles during dynamic loading are also investigated. Finally, the effects of presence of friction and adhesion on both overall particles deformation and compaction process are simulated. / QC 20110311

A uniaxial High-Velocity Compaction (HVC) process for polymer powder using a cylindrical, hardened steel die and a new technique with relaxation assist was tested with a focus on the compactibility characteristics and surface morphology of the compacted materials using various heights of relaxation assist device with different compacting profiles. Relaxation assist device was presented as a new technique to reduce springback, pull-out phenomenon and to improve the compaction process. The basic phenomena associated with HVC are explained and the general energy principle is introduced to explain pull-out phenomenon during the decompacting stage. In this study, polyamide-11 powders with different particle size distributions have been compacted with the application of different compaction profiles, e.g. different energies and velocities. It was found that the relative green density is influenced more by the pre-compacting (primary compaction step) than by the post-compacting (secondary compaction step). Experimental results for different compaction profiles were presented showing the effect of varying the opposite velocity during the decompacting stage and how to improve the homogeneous densification between the upper and lower surface and the evenness of the upper surface of the compacted powder bed by using relaxation assists, and the influences of the relaxation assist device on the process characteristics. It was found that the relaxation assist improves the compaction of the polymer powder by locking the powder bed in the compacted form. In addition, the relative times of the compacting stage, decompacting stage and the reorganisation of the particles can be controlled by altering the height of the relaxation assist. It was found that the high-velocity compaction process is an interruption process and that the delay times between the pressure waves can be reduced by increasing the height of the relaxation assist device. Furthermore, the first gross instantaneous springback and the total elastic springback are reduced. Two bonding strain gauges and a high-speed video camera system were used to investigate the springback phenomenon during the compaction process. Scanning electron microscopy (SEM) and image computer board Camera (IC-PCI Imaging Technology) were used to the study the morphological characteristics, the limit of plastic deformation and particle bonding by plastic flow at contact points, and pull-out phenomena. / QC 20100506

La Compaction à Grande Vitesse (CGV) est un procédé efficace pour mettre en oeuvre par frittage, et dans un temps court, des poudres polymères semi-cristallins quelle que soit leur viscosité en partant d’une température inférieure au point de fusion. L’échauffement et la fusion du matériau est obtenu par une succession d’impacts à une énergie donnée ce qui offre la possibilité de définir finement la quantité d’énergie que l’on souhaite apporter au matériau et la qualité du frittage. Une fusion partielle de la poudre permet de profiter de la cristallinité élevée de la poudre native, un compromis est alors possible entre de hautes propriétés élastiques et une ductilité élevée. La contre-partie de cette efficacité est une mise au point délicate du procédé. Dans le cas du polyéthylène ultra haute masse molaire (UHMWPE), il a été montré que le procédé permet une quasi-abstraction des effets de la masse molaire. Le frittage du UHMWPE demande seulement une réorganisation à courte distance des chaînes qui peut se faire dans un temps très limité. La cohésion de la poudre est assurée essentiellement par la cocristallisation et la création de nouveaux enchevêtrements. La modélisation du procédé a permis de comprendre comment l’énergie cinétique lors des impacts est transformée en chaleur dans la poudre et elle a permis l’établissement d’un critère de processabilité par CGV. Ce critère de processabilité repose sur la déformabilité de la poudre contenu dans la matrice au moment de l’impact. Celle-ci doit être suffisante pour que l’énergie dissipée dans le matériau permette sa fusion en moins de cent coups. Ceci a permis de comprendre pourquoi le polyoxyméthylène peut difficilement se mettre en forme par CGV. / High Velocity Compaction (HVC) is an efficient process to mold, in a short time, semicrystalline polymers powders any about their viscosity by starting from a temperature below melting point. Heating and melting occur by successive impacts at a preset energy that offers the possibility to set accurately the energy amount that we would bring to the material and the sintering quality. Partial melting of powder enable to take advantage of the high cristallinity of nascent powders, a compromise is possible between high elastic properties and high ductility. The flip-side of this efficiency is a delicate process settings. For the ultra high molecular weight polyethylene (UHMWPE), it has been shown that the process makes it possible a quasi abstraction of molecular weight effects. UHMWPE sintering needs only a short length reorganisation of chains that could be done in a really short time. Powder cohesion is essentially bring by cocrystallisation and by new entanglements creation. Process modelling allowed to understand how kinetic energy during hits is converted into heat in powder and it’s enable to define a HVC processability criterion. This processability criterion rests on the strainability of powder place in a die during a hit. It has to be sufficient to the dissipated energy in material allows his melting in less than one hundred impacts. This criterion allows to understand why the polyoxymethylene is hard to mold by HVC.