This work deals with the theoretical foundations of electron emission into vacuum, various types of emissions, focused on the cold-emission and Schottky emission and the principle of quantum tunneling. The next part deals with the technical implementation of electron sources with a detailed study of the methodology of laboratory production of cathodes by electrochemical etching and construction of electron microscopes, using field-emission sources. This work also contains methods for measuring, processing and evaluation of electrical characteristics of emission sources.

The master’s thesis deals with the principle of the photoelectric effect, the composition of the photovoltaic cell and different types of solar panels. Here is described the principle of converting wind energy into electricity. This master’s thesis describes reasons for using of the hybrid system. The next section describes the measurement system which is used to measure real operating statuses. The last section is an analysis of measured values and there are listed factors influencing the design of hybrid power system.

This thesis deals with reaction synthesis of materials Fe–Al, Fe–Cu and Fe–Ni from cold spray. In literature analysis are introduced these systems and for each system there is brief description of binary equilibrium diagram. Furthermore here are some short explanations of diffusion, Kirkendall effect and other possible processing technologies of intermetallic materials. In experimental part, samples of sprayed materials were annealed and then microstructural changes were investigated. This thesis contains photographs of microstructure, results from scanning electron microscopy, X-ray, and measurements of microhardness.

The subject of this thesis is the analysis of the negative effects associated with the operation of a trailer for a personal vehicle with respect to the design speed, technical checks and analysis related legislation. Its work is drawn from the measurement, cooperation with leading Czech production plant trailers Vezeko s.r.o., an organization engaged in the implementation of engineering controls DEKRA Automobil a.s. and available literature, including electronic resources. Results of the work end with proposals for specific measures to minimize the identified adverse effects.

The doctoral thesis discusses the measurement of parameters of piezoelectric (PZT) materials and the influence of temperature on their stability. In the introductory sections, the author briefly explains the piezoelectric effect and its use; simultaneously, methods for the preparation of piezoelectric materials and the measurement of their properties are presented to illustrate the analyzed problem. The experimental part of the thesis describes the procedure of measuring and calculating the complete matrix of material coefficients from samples of PZT ceramics. The applied set of piezoelectric samples complying with relevant European and world standards was made in the form of thin plates, thin discs and cylinders, via gradual modification of the large disc. The NCE51 and/or the older PCM51 ceramics obtained from the company Noliac Ceramics were used in determining the complete matrix and describing the measurement method. Both these types are soft piezoceramics composed from a solid solution of lead zirconate and lead titanate with the general chemical formula of Pb(Zr1-x,Tix)O3. The real crystallographic structure and chemical composition of the samples were confirmed by X-ray diffraction spectroscopy and energy dispersive spectroscopy (EDS), respectively. The frequency method was used for the measurement and calculation of all material coefficients. An Agilent 4294A impedance analyzer and a set of measuring tweezers marketed as “Tweezers Contact Test Fixture 16334A” were used in the process. Fast determination of the entire matrix of coefficients without any special requirement for the preparation of the samples to be measured was tested and verified. The charge coefficients of the piezoelectric material were confirmed by direct methods including the laser interferometer technique, the vibrometric method, and the procedure utilizing changes of the force applied to the sample. The advantages and disadvantages of the methods were compared and defined based on measurements and their results. The main part of thesis was focused on the behavior of piezoelectric material at high temperatures near the Curie point. Depolarization performed by means of a high temperature approaching the Curie point constitutes a significant yet hardly measurable material property of PZT ceramics. Commonly available vibrometric methods (d33-meters) do not appear to be suitable for the measurement of temperature dependencies, and for that reason the frequency technique was used. The piezoelectric charge coefficient, whose value can be effectively measured via the above-discussed frequency method, was selected as the indicator showing the depolarization state in the applied piezoelectric ceramics. The accuracy of the procedure was verified via comparison of the vibrometric method in cylinders of the NCE51 ceramics with different sizes, which are designed for the longitudinal length mode. The result is an optimized measurement methodology which facilitates accurate determination of the Curie temperature, namely phase transition to the cubic crystallographic structure. The experiment also proved the applicability of progressive, controlled depolarization of PZT ceramics via high temperature, and it also enabled us to define the temperature limits at which there occur irreversible changes of the piezoelectric properties of piezoceramics. In the measured NCE51 and PCM51 materials, the limit for the irreversible changes was equal to 95% of the Curie temperature.

This master's thesis describes ways of signal processing via digital devices. Major field of interest is an analysis of Doppler radar response and then mining of informations about detected object (e.g. speed, movement direction, length, ...). There was realized too little research, that's why borrowing some procedures from different branches not too much related to the IT is necessary. In case of using very complex methods that are easy to parallel, hardware implementation on the FPGA is supposed. With transceiver there is created a very powerful on-line system able to process most of tasks real-time. Then processed and transformed data are sent to the output so visualization and display can be made.

The Master´s thesis deals with issues of operational performance of two photovoltaic power plants. In the thesis is stated the history of photovoltaics, description of photovoltaic effect, used materials and production technology of the most used material in PV industry – Silicon. The basic parts and parameters of photovoltaic power plant are described. Thesis also solves, how could be done the first and periodically control due to relevant directives. The ways of diagnostics potentional failures, methods of measuring and the exam of monitoring system are stated. Practice part is focused on measuring and comparing operational performance of FVE Kurdějov and FVE Šakvice II. Operational performance was calculated from exported data for years 2014 and 2015. The thesis also contains measuring of each string connected to inventors, which are installed on the power plant. The result is an identification of strings with decreased operational performance. Based on that was created recommendations for optimalization and increase of the performance. The last part is software for simulation of photovoltaic power plant. This SW calculates potentional energy, which could be produced in a day with available data export. The calculation is defined by parameters, which are assigned.

Presented work deals with heat transfer and its methods. At the beginning thesis describes the theory and the ways of heat transfer with connected quantities and equations. Then it explains the stack effect and impact of temperature on electro technical device. In work is also described ABB driver ACS line and calculation of heat transfer according to IEC 60890 standard. In the practical part there is the calculation of heat transfer in Flow Simulation simulating CFD program solved and finite element method is mentioned. Important part of work is devoted to setting and optimization of simulation. In conclusion are made some changes of construction of driver, dependence on heat transfer is inspected.

CdTe and CdZnTe are promising materials for room temperature semiconductor X-ray and gamma ray detectors. The accumulation of a space charge at deep energy levels due to a band bending at contacts with Schottky barriers and due to trapped photogenerated charge may result in time dependent change of charge collection efficiency in CdTe and CdZnTe detectors known as polarization effect. This thesis is mainly focused on a study of electric field profiles in detectors under dark and high photon flux conditions simulating detector operation using crossed polarizers technique exploiting the electro-optic (Pockels) effect. It also deals with a study of deep levels responsible for the polarization and influence of contact metals on charge accumulation. Several experimental results are supported by theoretical simulations. The measurements were performed on three sets of samples equipped with different contact metals (Au, In) cut from three different n-type CdTe and CdZnTe materials. Energy levels were detected using methods based on the Pockels effect and discharge current measurements. Detailed study of internal electric field profiles has revealed a fundamental influence of near midgap energy levels related to crystal defects and contact metals on the polarization in semiconductor detectors under high radiation...

The spin transport and dynamics of optically injected spin polarized carri- ers are studied with a high spatial and/or time resolution in semiconductor GaAs-based heterostructures in multiple transport regimes. An unexpectedly long-scale and high-speed spin diffusion transport is observed in a long-lived electron sub-system induced optically at an undoped single GaAs/AlGaAs heterointerface. A diffusion and drift-dominated spin transport is investi- gated using an electrical spin-detection via the inverse spin Hall effect in doped GaAs-based systems at room and low temperatures. It is shown that the inverse spin Hall signal and the spin transport parameters can be con- trolled by a direct application of an electric field or by expanding a depleted zone of a planar pn-junction.