This work deals with issues of preparation of intermetallics based on iron, nickel and titanium aluminides. It works with an idea of preparation of bulk material by reaction synthe-sis from kinetic spraying deposits by cold spray. Theoretical part is concerned with phases and compounds of these aluminides for structural applications, their characteristics and present fabrication. In experimental part there are studied microstructures created by annealing of deposits.

Title: Point defects in materials for detection of X-ray and gamma radiation Author: Martin Rejhon Department: Institute of Physics of Charles University Supervisor: prof. Ing. Jan Franc, DrSc., Institute of Physics of Charles Uni- versity Abstract: Cadmium telluride and its compounds are suitable materials for pro- duction of X-ray and gamma-ray detectors working at room temperature. How- ever, the detector quality is affected by material imperfections, such as crystal defects and impurities. It results into forming of deep levels which act as re- combination and trapping centers. Then, the accumulated space charge at these deep levels influences electric and spectroscopic properties of the detector. In the end it may result in the polarization effect, when the electric field is localized in vicinity of one contact and detection properties are decreased. This thesis reports a complex study of a detector band structure by various meth- ods with focus on differences between CdTe, CdZnTe, CdTeSe and CdZnTeSe. The electro-optic Pockels effect is used to investigate the influence of the illumi- nation in range 900 − 1800 nm on the inner electric field. The temperature and time evolutions of the electric field after application of bias or switching of the additional light at 940 nm were measured to determine deep levels...

This master´s thesis is directed to an research of thermoelectric cells as power sources. It is discoursing about general properities of thermoelectric cells and their using at practical aplications in the first part. Then a heating and cooling system is designed and made for a selected type of thermoelectric cell which represents the emergency back-up power source. In the next part a DC/DC step-up converter is designed for a selected type of thermoelectric cell. This converter generates the DC load voltage 12V. The converter is controlled by PWM with a carrier frequency 50kHz.

The thesis includes diagnostics temperature field of industrial low voltage. Place of origin, flow and heat transfer are important aspects in the design of the switchgear, especially in terms of proper equipment layout. The correctness of the design of the switchgear is verified by measuring the practical temperature field during testing or in work mode. To determine the temperature profile, it is necessary to measure the temperature at various points of the switchgear, either contact or contactless method. Measurements are performed on standardized low voltage switchboards, which are located power elements. The goal is to replace costly and time-consuming field testing switchgear efficient simulation of the temperature field mathematical model developed switchboards.

In the last decade there is a rising interest in thermoelectric applications. Thermoelectric generators enabling the direct conversion of the heat into the electricity become attractive. This fact is caused by the demands of environmental operation and saving primary resources. Scientists intensively investigate and develop new materials and structures suitable for these applications. The efficiency of the thermoelectric conversion progressively increases. Unfortunately we have no available materials with sufficient thermoelectric properties which could provide cost-competitive price. Thermoelectric generators seem to be useable devices. For example, in case of the unused waste heat using of the thermoelectric generator can increase the overall effectiveness of the unit despite the low efficiency of the generator. This master thesis deals with the issue of the Peltier modules representing the main part of the thermoelectric generators. The physical principles and structures of the thermoelectric modules and the possibility of thermoelectric power production are described here. In the practical part of this thesis the design of the low power generator utilizing waste heat from biomass boiler Verner A 251.1 is proposed.

This theoretical thesis presents detailed study of negatively charged excitons - trions - confined in single quantum well in presence of perpendicular magnetic field. Complex valence band of GaAs/GaAlAs compound is described within Luttinger Hamiltonian framework. Singlet and triplet states of negative trion are introduced. Advanced theoretical analysis of Zeeman effect for different states of trion is performed. Landau gauge of magnetic field and unusual wavefunctions basis is chosen and its accuracy is tested. Evolution of ground state energy and photoluminescence spectra with magnetic field is evaluated for different values of Landé g-factors. Probability of occurrence of electrons with respect to the hole position and their spatial correlation function are investigated.

Solid oxide fuel cells (SOFC) are mainly used as large stationary elec- tricity sources, therefore an every little improvement in their performance leads to considerable savings. In order to understand the fundamentals of the SOFC operation, we have developed a new model describing the main physical processes. The thermodynamical model of SOFC, developed in this thesis, concerns the gas transport, the transport of the charged particles in- cluding the thermoelectric effect and the electrochemical reactions. Linear irreversible thermodynamics is the key modelling framework, in which the dusty gas model and the Butler-Volmer equations are used. A new relation between the electrochemical affinity and the overpotential is introduced into the Butler-Volmer equation. A weakly formulated statinonary system en- dowed with boundary conditions is solved with the finite element method in one dimensional approximation. 1

In-line heat treatment is a part of technological process uses a phase and structure changes to obtain required mechanical properties. Heat treatment of rolled products offers a reduction of steel making costs and a creation of new steel products. For example the TRIP steel is a part of modern steels which is used in the automobile industry for higher safety of passengers. The heat treatment is often described in the literature. But the authors are often focused on the method how to get the required structure and mechanical properties for different metallic materials. Nevertheless just few articles are focused on the technical observing of temperature regimes and which parameter is necessary to consider during designing the cooling section. Eight parameters were tested by the experimental way to examine their influence on the cooling intensity. They were: gravity (orientation of the cooled surface), coolant pressure, amount of coolant spraying on the surface (the flow rate), rolling velocity, nozzle configuration, kind of nozzles (full cone or flat fan nozzle), coolant temperature and the surface quality (surface roughness and scales). All these parameters have an influence the heat transfer coefficient. Based on knowledge gained in this work was created the cooling section, which comply with the required cooling temperature regimes.

The master thesis focuses primarily on issues of photovoltaic cells in terms of their defects. The introductory part deals with the history of photovoltaics, their introduction into practice and finally an explanation of the photoelectric effect itself. The thesis also describes photovoltaic cells themselves. It explains their principle, advantages, disadvantages and the creation of photovoltaic systems. A substantial part of the work is focused on the topic of detection of defects using luminescent methods. Subsequently, it describes procedural defects arising from the improper handling of already manufactured products. The final part deals with the main topic of the work, which is a detection using luminescence methods and it also mentions the non-luminescence method LBIC. The practical part of the master thesis contains the analysis of the current solution and of the subsequent proposal of solution using a low cost camera. It describes how to modify the camera, verify its spectral sensitivity using a spectrometer and measure the sensitivity of the CMOS sensor. The conclusion is focused on verifying the functionality of the proposed solution on different sources of infrared radiation and photovoltaic panels themselves.

The Master’s Thesis prospects the suitability of installing a photovoltaic system and a cogeneration unit in the LIPOELASTIC manufacturing facility and proposes their actual realization. Theoretical part describes said facility, its current energy supply situation and presents the proposed realizations' principle of operation. Practical part contains concrete calculations needed for realizations' proposal and their economic evaluation both independently and jointly.