The goal of this work is to experimentally assess the influence of limiting walls of Škoda Octavia 3 automobile cabin to the air jet flowing from the right-front situated automotive vent which is part of a car dashboard. The experiment is performed by the smoke visualization method. There is a single construction option measured for an experiment. The setup of the vanes direction and the air flow rate are modified for this option. The experiment is divided into two phases. In the first phase, the visualization of the free air flow is conducted. In the second phase, exit plates are constructed and consequently, the visualization of the wall-jet flow is conducted. The results of both are compared to each other. The results imply that the influence of the surrounding surfaces must be taken into account with the increasing flow rate for the vanes set in the direction of upper-right, middle-right, and middle-middle. There is a direct interaction between the flow and exit plates (the flow impact, the Coanda effect). The free flow does not contain the information about the mutual interaction between the flow and the exit plates, as it is in the case of the wall-jet flow. In the case of the wall-jet flow, the opening of the flow takes place due to the effect of the impact and the subsequential suction caused by the Coanda effect. The exit plates substituting the car dashboard and the front window contribute to the prevention of the air intake from surrounding space and consequently to earlier flow opening from the vent. The present work also contains the measurement methodology and the image evaluation, the comparison with previous free flow measurements (70% match) and the comparison to the measurement of hot-wire anemometry method.

Polymer and composite polymer-ceramic nanofibers were prepared by electrospinning process. Solution of 20 wt.% polyvinylidene fluoride (PVDF) in a mixture of dimethyl sulfoxide (DMSO) and acetone in the ratio of 7:3 was chosen as the most suitable precursor. When preparing composite nanofibers, 20 wt.% of barium calcium zirconate titanate (BCZT) or barium titanate (BT) nanoparticles was added to this PVDF solution. Given parameters were defined as the most suitable for the process of electrospinning: voltage of 50 kV, feeding rate of 30 l/min, distance between emitter and collector of 20 cm and needle diameter of 17 G. The effect of polymer molecular weight and the rotation speed of collector was also studied. Various properties of prepared samples were studied: morphology and fiber diameter, phase composition with the use of x-ray diffraction and Fourier transform infrared spectroscopy and also chosen electrical properties. Lower fiber diameters appeared with lower polymer molecular weight and higher rotation speed of the collector. These parameters resulted in higher percentage of the piezoelectric phase as well. The smallest achieved fiber diameter was around 300 nm, the highest percentage of phase was 92 % and the highest piezoelectric constant had a value of 16 pC/N. Composite fibers filled with BT particles showed better properties that the ones filled with BCZT particles.

This thesis deals with a design of telemetry archive of PSAT, PSAT-2 and BRICSat sattelites. This telemetry data need to be extracted from SDR IQ records. The thesis contains a Doppler effect theory and description of structure of telemetry data. Then it presents a design of a program for Doppler effect correction, demodulation and decoding of these records and saving the data to telemetry archive. Thesis also deals with analysis of decoded data.

The presented thesis discusses the basic analysis methods of arteriovelocitograms. The core of this work rests in classification of signals and contribution to possibilities of noninvasive diagnostic methods for evaluation patients with peripheral ischemic occlusive arterial disease. The classification employs multivariate statistical methods and principles of neural networks. The data processing works with an angiographic verified set of arteriovelocitogram dates. The digital subtraction angiography classified them into 3 separable classes in dependence on degree of vascular stenosis. Classification AVG signals are represented in the program by the 6 parameters that are measured on 3 different places on each patient’s leg. Evaluation of disease appeared to be a comprehensive approach at signals acquired from whole patient’s leg. The sensitivity of clustering method compared with angiography is between 82.75 % and 90.90 %, specificity between 80.66 % and 88.88 %. Using neural networks sensitivity is in range of 79.06 % and 96.87 %, specificity is in range of 73.07 % and 91.30 %.

The oldest and also most used type of secondary cells is lead-acid accumulator. Basic functional principle stayed same as in foundation time, only operation parameters are still improving (for example one of the most important is lifetime). Significant technical problem is temperature of lead-acid battery and her influence on functionality and running reactions. Master thesis is focused on this section, when is necessary to evaluate new pieces of knowledge in development. The work deals with description existing types of accumulators, further deals with theory of temperature balance and in the end by measured datas and theirs analyzing.

Lead –acid batteries are the most common type of secondary cells used in automotive industry. This diploma thesis deals with the influence of temperature on their lifetime. In the preamble of this work is shortly described their history, division, construction and processes during battery operation. There are noted unfavorable phenomena which have an impact on increasing the temperature inside the battery. The first experimental part is devoted to evaluation the effects of addition on the temperature rise during charging. The second part is focused on conditions simulation in hot areas at the temperature above 30 °C and effects of this temperature on the function of lead – acid batteries.

This work deals with the description and analysis of suitable methods for measurement of non-periodical high-level current pulses. For pulsed current source design and development a suitable measurement system is required. In this work shunt resistor, Rogowski sensor and magneto-optic sensor are presented. The analysis of their properties is performed in order to design a suitable sensor for test current pulse measurement. A design of Rogowski coil sensor has been made. An experimental measurement of current pulses with short time relations has been performed. The suitability of the coil sensor for non-harmonic waveforms measurement has been evaluated on the basis of measurement results. In case of the magneto-optic sensor a concept utilizing an optical fiber has been proposed. The design of the sensor has been performed also. Individual parts of the sensor were verified. Experimental magneto-optic sensors have been built and their properties have been studied.

This thesis deals with ultrasound blood flow meter design with emphasis on practical implementation of such device. This medical device is used in ultrasound diagnostic, especially for measuring direction and velocity of blood flow in superficial vessels. This thesis contains consecutive design including description of individual function blocks. Documents for making double-sided printed circuit are included as well.

The content of this thesis is the validation of the method of dynamic testing of solar photovoltaic cells. Testing methods for determining the parameters of the photovoltaic cell replacement scheme has been verified through testing a set of crystalline silicon photovoltaic cells. To accelerate the diffusion capacity measurement and to improve reproducibility of the measurement we propose new method of determining the time constant for diffusion capacitance using a combination of two short pulses. For this method of measurement new scheme for dynamic tester timing has been proposed and implemented.

This thesis focuses on the methodology of determining the parameters of Peltier batteries and the theory of construction of a cooling block on the basis of obtained parameters. Gathered information is then used for design and construction of a small test chamber for laboratory purposes.