No description available.

This thesis describes aspects of durability of Swedish softwood in above ground applications. The thesis consists of a summary of nine papers, which all aim to explain the existing variation in above ground microbial durability and moisture sensitivity of Norway spruce (Picea abies) and Scots pine (Pinus sylvestris). The methods used were two field tests, one accelerated durability test, and three water permeability tests. The main conclusions made in the study were that Norway spruce sapwood is more susceptible to discolouring fungi than heartwood. With respect to Scots pine, the only important factor for its natural durability above ground was whether the samples consisted of heartwood or of sapwood. There was also no systematic variation between pine heartwood from different stand origins in above ground conditions. Origin had no influence on durability in practice for neither spruce nor pine. Furthermore, in contradiction with traditional thinking, annual ring width and density had no influence on durability in any of the tests. The material came from two different samplings. The ‘old’ material was sampled in the beginning of the 1980s and consisted of Scots pine and Norway spruce from three different origins: the north, the central area, and the south of Sweden. The material was subjected to different handling conditions and surface and end-grain treatments. The ‘old’ material was used in a large above ground field test, carried out between 1985 and 1994. Unfortunately, the spruce sapwood and heartwood was not separated in this field test. In the field trial with the ‘old’ material, the most important factor for the durability of Norway spruce was the samples’ surface- and end-grain treatment. It was also observed that untreated spruce showed better durability than samples that were painted but without proper end-grain treatment. Samples originating from one of the stands were more sensitive towards air-drying than samples from the other two, which was reflected in a higher average moisture content and mass loss for the untreated samples. With respect to Scots pine, the most important factor was whether the sample consisted of heartwood or of sapwood. The heartwood samples were durable irrespective of their previous treatment. The Scots pine sapwood samples, on the other hand, had a very fluctuating moisture content if they were not surface- and end-painted. This was also reflected in higher mass losses in these samples. Even when properly surface- and end grain treated, the sapwood samples did not perform as well as the heartwood samples. The ‘new’ material consisted of Scots pine taken from six different stands, and Norway spruce from five different stands, all from areas in southern Sweden. The sampling was performed in order to achieve a large variation in wood properties. Thus, logs from areas with different climate and growth conditions were collected. This material was used for laboratory tests, and also for the second field test, which was evaluated after a test period of two years. In the second field test untreated Scots pine and Norway spruce samples from the ‘new’ material were investigated. Effects of origin and different tree diameters were examined. Furthermore, Scots pine was separated to heartwood and sapwood, and Norway spruce to mature and juvenile wood. The Norway spruce samples were sawn with vertical or horizontal annual rings. For the Norway spruce in the second field test, vertical annual rings were shown to be very beneficial for avoiding crack formation, while samples with horizontal annual rings displayed a large number of cracks. Despite this, the larger number of cracks did not result in a higher moisture content or more fungal discoloration. Juvenile wood had a slightly higher average discolouring fungal growth grading than the other spruce samples. For Scots pine, the only factor of importance was whether the samples consisted of heartwood or of sapwood. Annual ring width, density and origin had no significant effect on either fungal growth or moisture uptake. This observation held for both Norway spruce samples and Scots pine samples. An accelerated test was run in order to investigate Norway spruce sapwood and heartwood with respect to their differences in durability towards discolouring fungi and moisture uptake. The Mycologg method was used to accelerate fungal growth during a number of forced moisture cycles. The results showed that sapwood was much more sensitive to discolouring fungi than heartwood. Sapwood also recorded a higher average moisture content than heartwood. The differences that were observed between the types of samples were not due to annual ring width, density or origin. It was observed that Norway spruce sapwood samples and heartwood samples showed differences in liquid water permeability. This observation was made especially evident in a droplet absorption test. Water droplets were absorbed much faster on the sapwood samples in comparison with the heartwood samples. This higher affinity to water suggested that a sapwood surface would reach a higher moisture content than a heartwood surface. This observation provides a major explanation of why the sapwood samples showed poorer durability towards discolouring fungi in the Mycologg trials.

The Swedish deciduous forest has been actively replaced by coniferous forest during the last two hundred years. In Färna Ekopark, Västmanland, this trend is being reversed by restorations of deciduous forests through the removal of coniferous trees in mixed forests. This field study investigates how successful these restorations have been for plant diversity and how they were affected by past grazing and the proportion of similar mixed and deciduous forest habitats in thesurrounding landscape. Plant species richness was investigated in 370 1m2-plots distributed over 37 sample areas and the surrounding landscape analyzed in a GIS. Results show that a few years after restoration there was higher plant species richness and lower homogenization, at the site scale, compared to the controls. When the restored sites were divided into two subgroups dependant on age, the 5-6 year old restoration displayed higher plot richness than the 2-4 year old restorations, but were also more homogeneous. Past grazing showed a generally positive effect on plant diversity, and these areas also responded with a larger increase of plant species richness and less homogenous plant populations after restorations compared to areas that had not been formerly grazed. The proportion of similar deciduous and mixed forest habitats (more than 40 % deciduous trees) inthe surrounding landscape showed no effect on the plant diversity of deciduous forests in general, though it did display a weak influence over the plot richness of restored deciduous forests without a history of grazing. When restoring deciduous forests to increase plant diversity it would therefore appear wise to focuson the formerly grazed deciduous forests. To take advantage of the beneficial effects to plot richness restored deciduous forests should have a high degree of deciduous and mixed forests within one kilometer. / Den svenska lövskogen har aktivt ersatts med barrskog under de senaste tvåhundra åren. I Färna Ekopark, Västmanland, försöker man vända denna trend genom att ta bort barrträd i blandskog ochpå så sätt restaurera lövskog. Denna fältstudie undersöker om restaureringarna har gett ökad växtdiversitet och hur restaureringarna har påverkats av tidigare bete samt andelen av liknande bland- och lövskogshabitat i det omgivande landskapet. Växtartantalet undersöktes med 370 1m2-rutor utspridda över 37 områden och det omgivande landskapet analyserades i ett GIS. Resultaten visar att några år efter restaurering hade områdena högre växtdiversitet och artsammansättningen var mindre likformig i jämförelse med kontrollerna. När de restaurerade områdena delades upp i två grupper, i avseende på ålder, uppvisade de 5-6 år gamla restaureringarna högre växtdiversitet i rutorna än de 2-4 år gamla restaureringarna, men artsammansättningen var även mer likformig. Tidigare bete visade en generellt positiv inverkar på växtdiversiteten och dessa områden fick en ännu större uppgång i artrikedom och ännu lägre likformighet i artsammansättningarna efter restaureringarna än de områden som inte hade betats tidigare. Andelen av liknande bland- och lövskogshabitat (mer än 40 % lövträd) i det omgivande landskapet uppvisade ingen effekt på växtdiversiteten hos lövskog generellt, men det fanns en svag påverkan på växtdiversiteten på rutnivå hos restaurerade lövskogar utan tidigare bete. När man restaurerar lövskog för att öka växtdiversiteten verkar det därför bra att fokusera på tidigare betade lövskogar. Om man vill ta tillvara på den positiva påverkan på växtpopulationerna som omgivande landskap kan ha bör restaurerade lövskogar ha en stor andel bland- och lövskog en kilometer runt omkring sig.

Procurement of sawlogs to purchasing sawmills represents a basic strategic business process. The properties of inbound sawlogs are decisive for the output of sawn products and the cost of raw material contributes substantially to the cost of the final product. Increasing customer orientation and new demands from powerful customers in the building and retail sectors entail new or accentuated demands on management of procurement. Managing raw material procurement and communicating needs to suppliers and logging machine operators are vital issues for sawmills in order to be competitive. The purpose of the thesis is to explore how purchasing sawmills manage procurement of sawlogs. The results are based on 46 in-depth interviews with people involved in the procurement process at seven softwood sawmills in Denmark, Finland and Sweden. The thesis identifies various types of supply uncertainties as well as process improvement and buffer activities that reduce uncertainties. However, the major obstacle in the procurement process is the power/dependence balance in the relationships with suppliers. Beyond doubt, it restricts the manageability of procurement and particularly bucking. The results suggest that there are a number of ways to improve management of procurement, which are currently not fully employed. The thesis provides four key strategic dimensions of the procurement process and suggests a general conceptual model of wood procurement to purchasing sawmills. Further research within the subject can usefully explore the link between procurement management and procurement strategy as well as the relation to other functions' strategies and the corporate strategy. The importance of the identified strategic dimensions of the procurement process needs to be quantified in order to provide normative suggestions.

Wood is a major construction material that is used in many contexts, and for different purposes. Serious problems may arise, however, when moisture related deformations as twist occur in wood used in different types of building structures, joinery and furniture. Twist can be explained to a great degree by the helical deviation of the grain angle in relation to the longitudinal direction of the log or the sawn board. Wood fibres form a spiral within the tree, and this is a natural occurrence that is named spiral grain. The wood fibres close to the pith in Norway spruce form a left-handed spiral. In most trees the grain angle turns over to be right-handed with time. Sawn timber that exhibits large grain angles lead to problems of shape stability and stiffness in finished constructions. In this thesis the spiral grain in Norway spruce (Picea abies (L.) Karst.) was stated as well as the effect on sawn timber. The material was based on sample trees from Sweden and Finland. Samples were taken in twenty-two stands at different heights in tree. From six stands studs were sawn and dried for measuring twist and other deformations. The spiral grain was measured with the method scribe test on 390 log discs taken at the top-end of the logs. Account was given concerning changes in grain angle from pith to bark, regarding both increasing annual ring numbers and distance from pith. The development of grain angle over tree age was utilized to study whether annual growth, size of tree, height in tree as well as silvicultural treatments affected spiral grain. Moreover, the relation between grain angle and distance to pith (in mm) was used to forecast twist in sawn timber. The left-handed grain angle was at its greatest between the fourth and eighth annual rings. Thereafter for most trees the grain angle turned from left-handed to right-handed in a linear fashion, in a manner that was unique for each individual tree. The pattern of spiral grain differed significantly between different stands, regarding change of inclination with increasing age or distance from pith. The culmination of the grain angle close to the pith occurred at somewhat higher age higher up in the trunk. The grain angle decreased faster in top logs than it did in the butt logs. The largest trees within a stand had a grain angle that turned to right in a slower way than smaller ones. The thinning strength and type of thinning regime also affected the character of spiral grain in the remaining trees in a stand. There was an indication that strong thinnings, where fast growing trees are retained, may lead to more individuals in a stand that exhibit high grain angles under bark. With knowledge of the size and direction of the grain angle under bark, and the diameter of the log, calculations can be made that show how twisted the sawn timber will be after drying. This can be used for deciding whether an individual log can profitably be sawn and processed further or not. The grain angle under bark can be used to remove trees showing the greatest degree of spiral grain already in the first thinning. Silvicultural methods aiming at even and dense Norway spruce stands, which normally is practised in Scandinavia, will probably result in timber with relatively low risk concerning large grain angle and subsequent risk for twist in sawn wood.

Abstract 3D visualization of geological structures is a very efficient way to create a good understanding of geological features. It is not only an illustrative way for common people, but also a comprehensive method to interpret results of the work. Geologists, geophysics engineers and GIS experts sometimes need to visualize an area to accomplish their researches. It can show how sample data are distributed over the area and therefore they can be applied as suitable approach to validate the result. Among different 3D modeling methods, some are expensive or complicated. Therefore, such a methodology enabling easy and cheap creation of a 3D construction is highly demanded. However, several obstacles have been faced during the process of constructing a 3D model of geology. The main debate over suitable interpolation methods is the fact that 3D modelers may face discrepancies leading to different results even when they are working with the same set of data. Furthermore, most often part of data can be source of errors, themselves. Hence, it is extremely important to decide whether to omit those data or adopt another strategy. However, even after considering all these points, still the work may not be accurate enough to be used for scientific researches if the interpretation of work is not done precisely. This research sought to explain an approach for 3D modeling of Sedini platform in Sardinia, Italy. GIS was used as a flexible software together with Surfer and Voxler. Data manipulation, geodatabase creation and interpolation test all have been done with aid of GIS. A variety of interpolation methods available in Surfer were used to opt suitable method together with Arc view. A solid 3D model is created in Voxler environment. In Voxler, in contrary to many other 3D types of software there are four components needed to construct 3D. C value as 4th component except for XYZ coordinates was used to differentiate special features in platform and do gridding based on chosen value. With the aid of C value, one can mark layer of interest to identify it from other layers. The final result shows a 3D solid model of the Sedini platform including both surfaces and subsurfaces. An Isosurface with its unique value (Isovalue) can mark layer of interest and make it easy to interpret the results. However, the errors in some parts of model are also noticeable. Since data acquisition was done for studying geology and mineralogy characteristics of the area, there is less number of data points collected per volume according to the main goals of the initial project. Moreover, in some parts of geological border lines, the density of sample points is not high enough to estimate accurate location of lines. The study result can be applicable in a broad range of geological studies. Resource evaluation, geomorphology, structural geology and GIS are only a few examples of its application. The results of the study can be compared to the results of similar works where different softwares have been used so as to comprehend pros and cons of each as well as appropriate application of each software for a special task.     Keywords: GIS, Image Interpretation, Geodatabase, Geology, Interpolation, 3D Modeling

The aim of this thesis is to identify how forest management in Tanzania can contribute to global climate change mitigation while improving livelihoods of forest-dependent communities. A mechanism for reducing emissions from deforestation and forest degradation (REDD) is meant to slow increases of atmospheric CO2 while channelling funds to developing countries. In Tanzania, pioneering work in participatory forest management (PFM) has promoted local-level control over forest resource use. The purpose of this study is to contribute to a linkage between REDD and PFM that maximises benefits for communities, forests and global climate. Three PFM projects with relation to REDD have been studied, primarily using semi-structured interviews with villagers, district officials, project facilitators, researchers, consultants and policy-makers. Analysis consists of comparing experiences at different levels and putting them in the theoretical context of climate change and forest conservation. The study identifies several issues: local and central government institutions cannot ensure equitable benefit sharing; cross-sectoral co-ordination to address fundamental causes of the problems is lacking; participation of local communities is not satisfactory. However, the process is at an early stage. Current activities will hopefully contribute to a future framework that properly addresses these and other obstacles. If this is accomplished, PFM and REDD can complement each other in a positive way.

Modern weeding is predominantly carried out by spraying whole fields with toxic pesticides, a process that accomplishes the main goal of eliminating weeds, but at a cost of the local environment. Weed management systems based on AI solutions enable more targeted actions, such as site-specific spraying, which is essential in reducing the need for chemicals. To introduce sustainable weeding in Swedish farmlands, we propose implementing a state-of-the-art Deep Learning (DL) algorithm capable of instance segmentation for remote sensing of weeds, before coupling an automated sprayer vehicle. Cereals have been chosen as the target crop in this study as they are among the most commonly cultivated plants in Northern Europe. We used Unmanned Aerial Vehicles (UAV) to capture images from several fields and trained a Mask R-CNN computer vision framework to accurately recognize and localize unique instances of weeds among plants. Moreover, we evaluated three different backbones (ResNet-50, ResNet101, ResNeXt-101) pre-trained on the MS COCO dataset and through transfer learning tuned the model towards our classification task. Some well-reported limitations in building an accurate model include occlusion among instances as well as the high similarity between weeds and crops. Our system handles these challenges fairly well. We achieved a precision of 0.82, recall of 0.61, and F1 score of 0.70. Still, improvements can be made in data preparation and pre-processing to further improve the recall rate. All and all, the main outcome of this study is the system pipeline which, together with post-processing using geographical field coordinates, could serve as a detector for half of the weeds in an end-to-end weed removal system. / Site-specific Weed Control in Swedish Agriculture

Urban areas around the world are changing constantly and therefore it is necessary to update urban land cover maps regularly. Remote sensing techniques have been used to monitor changes and update land-use/land-cover information in urban areas for decades. Optical imaging systems have received most of the attention in urban studies. The development of SAR applications in urban monitoring has been accelerated with more and more advanced SAR systems operating in space.   This research investigated object-based and rule-based classification methodologies for extracting urban land-cover information from high resolution SAR data. The study area is located in the north and northwest part of the Greater Toronto Area (GTA), Ontario, Canada, which has been undergoing rapid urban growth during the past decades. Five-date RADARSAT-1 fine-beam C-HH SAR images with a spatial resolution of 10 meters were acquired during May to August in 2002. Three-date RADARSAT-2 ultra-fine-beam C-HH SAR images with a spatial resolution of 3 meters were acquired during June to September in 2008.   SAR images were pre-processed and then segmented using multi-resolution segmentation algorithm. Specific features such as geometric and texture features were selected and calculated for image objects derived from the segmentation of SAR images. Both neural network (NN) and support vector machines (SVM) were investigated for the supervised classification of image objects of RADARSAT-1 SAR images, while SVM was employed to classify image objects of RADARSAT-2 SAR images. Knowledge-based rules were developed and applied to resolve the confusion among some classes in the object-based classification results.   The classification of both RADARSAT-1 and RADARSAT-2 SAR images yielded relatively high accuracies (over 80%). SVM classifier generated better result than NN classifier for the object-based supervised classification of RADARSAT-1 SAR images. Well-designed knowledge-based rules could increase the accuracies of some classes after the object-based supervised classification. The comparison of the classification results of RADARSAT-1 and RADARSAT-2 SAR images showed that SAR images with higher resolution could reveal more details, but might produce lower classification accuracies for certain land cover classes due to the increasing complexity of the images. Overall, the classification results indicate that the proposed object-based and rule-based approaches have potential for operational urban land cover mapping from high-resolution space borne SAR images. / QC 20101209

The project studies environmental and social sustainability of alternative food networks (AFNs) in Jönköping County, Sweden by investigating the development of alternative food networks as part of a pre-study for Region Jönköping’s Län project Återtag av livsmedel från Naturbruksskolorna i länet till sjukhusrestaurangerna. The purpose of the study was to identify challenges and opportunities of implementing AFNs and to determine suggestions for overcoming these challenges. The purpose was achieved by investigating Region Jönköping Län's project to implement meat and vegetables produced by Jönköping County's agricultural high schools into the kitchens of the regional hospitals to become meals for patients and visitors.