This diploma thesis deals with the design of multifunctional building in Tábor in cadastre unit of Klokoty. It is a detached building with one underground floor and three above-ground floors on a flat terrain. The building is rectangular shape where the underground floor is a collective garage at the ground floor are shops a hairdresser and a café and at the last two floors are office spaces. The building is designed as frame systém with infill ceramic masonry with additional insulation. The roof is designed as a flat roof.

The diploma thesis deals with the project documentation of the accommodation facility - a mountain pension in the village of Rudná pod Pradědem. The building has an irregular floor plan and is divided into two parts. One part of the building is used for accommodation with a capacity of 16 people. It has two floors and consists of a flat, green roof. In the second part of the building, on the first floor there is a cafe, massages and infrared sauna. In the basement there is a technical background of the building. Office space and accommodation unit are located in the attic of the building. It consists of a saddle roof. The building is based on simple concrete foundation strips. The vertical load-bearing structures are made of ceramic blocks and blocks of lost formwork in the basement. Ceiling structures are designed as reinforced concrete, monolithic. The building is designed on a sloping terrain.

The task of the master project is to design a single-storey kindergarten with flat extetensive green roof in Chvalčov. The building contains entrance hall, utility room, locker rooms, toilets, kitchen, school canteen, staff rooms, storage room and play rooms. The Building is divided into two similar parts. The vertical loadbearing structure is designing from ceramic blocks. The horizontal loadbearing structure is designed from reinforced concrete. The building is heated by a ground source heat pump supplying heat to floor heating. Another source of heat for the preparation of hot water and heat exchanger in the air handling unit is a gas condensing boiler. The heat pump in reverse operation cool the building via Fan-coil units. For air distribution is designed galvanized ducts and air handling units. The building uses photovoltaics to produce electricity for safe environment when using a renewable energy source and safe money when they no need buy energy from elektricity distribudion networks. The designs were elaborated in Revit, autocad and thermal assessment in Deksoft and similation 2018

The subject of this master’s thesis is a project documentation for development of a nursery school. The nursery school is situated on the outskirts of the city Příbor. The school is designed as a two-storey building and includes 4 classrooms, with total capacity reaching 60 pupils. The perimeter wall consists of Porotherm clay block walling system. The ceiling framework uses a combination of two systems; the prestress hollow core slabs Spiroll and reinforced concrete monolithic blocks. The roof is designed as a single skin cladding with a flat, green roof. The external thermal insulation composite system (Etics) is proposed for the insulation of the building. The outer walls are partially cladded with timber. Additionally, the combination of white rendering and timber cladding will form a modern looking building that fits within a new housing development. Furthermore, the plan includes an outside playground, with allotments and parking spaces on the premises for the use of a nursery school.

The main subject of my diploma thesis is creating a design documentation for the construction of a hotel. The hotel has its own restaurant and is situated in the northern outskirts of Žďár nad Sázavou. The building is located on a slightly sloping terrain with small green vegetation. The hotel is three-story with partial basement. It is roofed with a pitched roof. The hotel meets the requirements of comfort star (***) in hotel rating. The accommodation capacity is 58 people placed into 13 rooms. Two rooms are designed to be accessible for people with reduced mobility and orientation. The rooms are located on the first and second floor. On the ground floor, there is an entrance hall with reception and toilets for the guests from the restaurant. In the south-western part of the hotel are located staff facilities such as a kitchen facility or a place of supply. The north-western part of the building is designed for the management and support areas. The building is designed to respect local regulations and construction principles. With its architectural design, the building completely fits into the surrounding landscape and does not disturb its character in any way.

The aim of this master thesis is multi-criteria assessment SBToolCZ of the building district department for Czech police in Kyjov. The building has a basement with underground garages, shooting range and technical facilities (boiler room, air conditioning room, storage, archives, cleaning room), and a ground floor with offices covered by a flat roof. The load-bearing structure of the basement is designed from watertight reinforced concrete. The ground floor has ceramic block walls. The floor and roof structure are designed from pre-stressed Spiroll. The building envelope is insulated with ETICS. The thesis also contains project documentation of building and HVAC design. The project was carried out in the AutoCad programme. Project documentation was prepared according to valid legal and technical regulations.

The main goal of this thesis is elaboration of a project documentation for the building permission of nearly zero energy office building with BIM, and assessment of the designed building by methodology for multicriteria evaluation of buildings. The building is located on a slightly sloped site of former military barracks in Valašské Meziříčí. The building is intended as offices for ENERGIS company. The building has rectangular floor plan (approx. 32 x 22 m). The building has three floors. There is café, reception, technical and storage facilities on the first floor. The second and third foor contain offices, meeting rooms and staff facilities. All floors are wheelchair accessible. The building has a cast-in-place reinforced concrete frame and warm flat roof. Infill walls are made of ceramics blocks. The facade wall is covered with ventilated facade with timber cladding.

The subject of this diploma thesis is the elaboration of project documentation for the construction of a new sports center with a specialization in the field of health technology. The building will be located in the town of Velké Meziříčí, on the street Školní and will be located on the plot 5917/16 with a total area of 17 820,2 m2. The total built-up area of the proposed building is 919,88 m2. The object is designed as stand-alone. It has a ragged shape, which consists of three adjoining rectangles, has two above ground floors with a partial basement. The building will be based on concrete foundation girders. The support system is chosen as a brick longitudinal with reinforcing walls. Perimeter masonry will be designed from cut ceramic blocks in above-ground floors and lost formwork in the basement. The ceiling structure consists of prestressed ceiling panels. The entire building is designed with a ventilated facade of two types of cement-bonded slabs. The grille of the ventilated facade will be made of glass fiber fiberglass. The roof of the building is designed as flat single-skinned. The building is designed for sports, including a sports bar and a clubhouse, which are open to the general public. There are 40 parking spaces, of which 3 for people with reduced mobility. During processing the emphasis was put on the appropriate layout, building-technical and architectural design and safe use of the building.

This master thesis focuses on the design and elaboration of project documentation for the purpose of constructing Industrial park with administration building consisting of two parts, SO 01 – Administration building and SO 02 – Industrial building. The two objects are situated on the plot No. 715/1, in the cadastre unit Vrbno pod Pradědem located on an undeveloped land of the investor. The exit from the parking lot connects to the local traffic infrastructure. Public infrastructure leads in proximity to the land. The design of the construction respects local zoning plan. Project documentation was made in compliance with up-to-date requirements according to valid standards and regulations. The building is functionally divided into two objects, SO 01 and SO 02, which are operationally and structurally connected. Constructions of both objects are statically independent. The object SO 01, partially accessible to the public, is used for administrative tasks and staff facilities. Also, there is a sample room available to the public, gatehouse and warehouses. The object SO 02 is purposed for the production of plastic windows and solar panels. It mainly consists of areas used for production, but there is also an office for the master, a machine room for heating, ventilating and air conditioning (HVAC) and staff facilities. The object SO 01 is designed from a wall structural system from clay masonry, clay ceilings, strip foundation and a flat roof. The object SO 02 is designed as a full-metal prefabricated object with a saddle roof and foundation pads. The construction system of this object consists of steel columns. Plan dimensions of SO 01 are 25x14 metres. Building envelope is made from clay blocks, 440 mm in width, filled with mineral wool. Plan dimensions of SO 02 are 66,9x22,9 metres. Object’s curtain walling is made from prefabricated sandwich panels containing a core from PUR material.

This master thesis elaborates the project documentation for the construction of an office building in Krnov city, located in the Moravian-Silesian region. The office building has four utility above-ground floors and one underground floors serving as underground garages. There is a cafe, stationery, showrooms and office space with sanitary facilities. The construction system is designed as a monolithic reinforced concrete skeleton. Vertical infill constructions are made of brick technology from Porotherm ceramic blocks. The ceiling structures are made of filigree panels with hidden steel girders, which are embedded with concrete layer. The basement and the basic structure of the house is designed as a white tub. The building is covered with vegetation roof. The design emphasized increased comfort in use and the overall modern concept of an office building. Overall, the building is designed to the required values for a near zero energy building.