The point of the thesis was to design a heating system for new residential building, situated in Nový Lískovec, Brno. As a source of heat has been designed condensing boiler fueled by gas that meets the need for heating of heating system and hot water. All of the equipment will be located in a utility room on the ground floor. In the apartment have been designed decorative panel radiators.

This master's thesis deals with the design of stoker-fired boiler for combustion of biomass. The main points of work are stoichiometry calculation of combustion, determining the dew point of flue gas, calculation of losses, which ones serves for determination of boiler efficiency, dimension design and detail calculation of thermosetting surfaces. In the last chapter is numbered total balance and real thermal efficiency of boiler.

The topic of thesis is condensing turbine in gas-steam cycle, which can be divided into four basic parts. A history of gas-steam cycle is described in the beginning. Second part is all about calculation of heat recovery steam generator. Penultimate section deals with calculations of steam turbine parameters and reaction blading type. Last part contains electric power and steam turbine efficiency.

This work deals with the topic – Heating with the use of large radiating structures. Theoretical part contains distribution underfloor heating, wall heating and ceiling heating. This topic is applied to the specified building. The project deals with preparing of domestic water, wall heating and underfloor heating. Experimental part deals with the measurement of ceiling heating.

The thesis examines the suitability of a CHP project in Bystřice nad Pernštejnem, a small town in Vysočina region, Czech Republic, which is currently supplied by biomass central heating. It reviews situation and availability of renewable energy sources and opportunities for CHP both in the Czech Republic and in Europe, including the context of current global developments. The opening chapters are followed with the renewable energy project for Bystřice nad Pernštejnem itself. The current technology, availability of biomass fuel for a potential future project, and possible development of energy sources in the town are analysed. Three alternative solutions for the CHP plant are suggested, with proposal for the technology and economic analysis, and possible future steps of the town council are discussed.

This Master’s thesis focuses on the design of vertical heat recovery steam generators. This work focuses on three main objectives. The first objective is to describe the heat recovery steam generators, there basic principle and construction. The second focal objective is thermal calculation, design of heat tranfer surfaces and choice of materials. The third objective was to calculate the boiler loss, hydraulic calculation and subsequent design of the drum dimensions.

Small domestic hot water boilers burning solid fuels represent a significant source of air pollu-tion. It is therefore an effort to increase their combustion efficiency and to reduce the produc-tion of harmful emissions. For this reason, the operation of older and currently unsatisfactory types of household boilers has been legally restricted. Preferred types of boilers are low-emission boilers, especially automatic or gasification boilers. Most of them, however, in compar-ison with previous types of boilers, also require connection to the electricity grid. If there is a long-term failure in electricity grid, the operation of newer boiler types is limited. Wood and coal gasification boilers are currently available on the market and can be operated even in the event of a power failure, but only in heating systems with natural water circulation. In heating systems with forced water circulation, these boilers, fireplaces or fireplace inserts with hot-water heat exchangers cannot be operated without external battery supply in the event of a power failure. The dissertation thesis therefore deals with the question of whether it would be possible by thermoelectric conversion of waste heat of flue gases of small-scale low-emission combustion hot water domestic boilers to obtain sufficient electricity, to power supply their circulation pumps and to ensure operation in systems with forced water circulation independently of elec-tricity supply from the grid. In order to answer this question, a simulation tool predicting the power parameters of ther-moelectric generators was created. Compared to previously published works, the calculations and simulations include the influence of the generator on the boiler flue gas functionality. To verify the simulation tool, an experimental thermoelectric generator was built using the waste heat of the flue gas of an automatic hot water boiler for wood pellets. In addition to this genera-tor, there was also created an experimental thermoelectric fireplace insert and other equipment related to these experiments.

This thesis deals with design of hot water grate boiler, where the output is water with parameters 130 °C and pressure 16 bar. In the content of the whole thesis is gradually introduced a stoichiometric calculations, which is based on the specified fuel – wood chips. This is followed by the design of the individual heating surfaces according to the thermal calculations given in the thesis. Finally, the calculation is extended by hydraulic and aerodynamic losses. Dimensional design, as a basic scheme, is shown at thesis. More detailed drawing documentation is attached to this thesis.

The diploma thesis is focused on district heat supply, heat sources, machinery and safety equipment of boiler rooms. The main goal of the thesis is to modernize parts of the heat sources with the respective boiler room equipment in accordance with the latest available technology. The generated thermal energy is used for heating or hot water production for residential and non-residential buildings in the vicinity of the boiler room. In the theoretical part, the thesis focuses in more detail on boiler rooms, specifically on heat energy sources, machinery and safety equipment of boiler rooms, system ventilation and combustion exhaust. The findings are applied in the design of the new boiler room layout. It is followed by a detailed description of the current state of the boiler room and heat networks. An essential part of the work is the assessment of layout of the current heat sources and the creation of a new design for the replacement of insufficient sources and related equipment. The last goal is an economic overview of the designed project solution.

The diploma thesis deals with the energy audit of the kindergarten building Špálova in Ostrava, according to order No. 480/2012 Sb. as amended. It is divided into three parts. The first part deals with the project of photovoltaic power plants in the energy audit, the second part analyzes the calculation procedures in the design of energy-saving measures and the third part completes the energy audit according to the requirements of the above-mentioned decree.