Structural analysis of highway bridges using complicated 3-D FEMs to determine live load effects in bridge components is possible due to the readily available computational tools in design offices. However, building such complicated 3-D FEMs is tedious and time consuming. Accordingly, most design engineers prefer using simplified 2-D structural models of the bridge and live load distribution equations (LLDEs) available in current bridge design codes to determine live load effects in bridge components. Basically, the live load effect obtained from a 2-D model is multiplied by a factor obtained from the LLDE to calculate the actual live load effect in a 3-D structure. The LLDE available in current bridge design codes for jointed bridges were also used for the design of straight and skewed integral bridges by bridge engineers. As a result, these bridges are either designed conservatively leading to additional construction cost or unconservatively leading to unsafe bridge designs. Recently, LLDEs for integral bridges (IBs) with no skew are developed. To use these equations for skewed integral bridges (SIBs) a correction factor is needed to multiply these equations to include the effect of skew. Consequently, in this research study, skew correction factors for SIBs are developed. For this purpose, finite element models of 231 different three dimensional and corresponding two dimensional structural models of SIBs are built and analyzed under live load. The analyses results reveal that the effect of skew on the distribution of live load moment and shear is significant. It is also observed that skew generally tends to decrease live load effects in girders and substructure components of SIBs. Using the analyses results, analytical equations are developed via nonlinear regression techniques to include skew effects in the LLDEs developed for straight IBs. The developed skew correction factors are compared with FEAs results. This comparison revealed that the developed skew correction factors yield a reasonably good estimate of the reduction in live load effects due to the effect of skew.

Integral bridges (IBs) are defined as a class of rigid frame bridges with a single row of piles at the abutments cast monolithically with the superstructure. In the last decade, IBs have become very popular in North America and Europe as they provide many economical and functional advantages. However, standard design methods for IBs have not been established yet. Therefore, most bridge engineers depend on the knowledge acquired from performance of previously constructed IBs and the design codes developed for conventional jointed bridges to design these types of bridges. This include the live load distribution factors used to account for the effect of truck loads on bridge components in the design as well as issues related to the seismic design of such bridges. Accordingly in this study issues related to live load effects as well as seismic effects on IB components are addressed in two separate parts. In the first part of this study, live load distribution formulae for IB components are developed and verified. For this purpose, numerous there dimensional and corresponding two dimensional finite element models (FEMs) of IBs are built and analyzed under live load. The results from the analyses of two and three dimensional FEMs are then used to calculate the live load distribution factors (LLDFs) for the components of IBs (girders, abutments and piles) as a function of some substructure, superstructure and soil properties. Then, live load distribution formulae for the determination of LLDFs are developed to estimate to the live load moments and shears in the girders, abutments and piles of IBs. It is observed that the developed formulae yield a reasonably good estimate of live load effects in IB girders, abutments and piles. In the second part of this study, seismic performance of IBs in comparison to that of conventional bridges is studied. In addition, the effect of several structural and geotechnical parameters on the performance of IBs is assessed. For this purpose, three existing IBs and conventional bridges with similar properties are considered. FEMs of these IBs are built to perform nonlinear time history analyses of these bridges. The analyses results revealed that IBs have a better overall seismic performance compared to that of conventional bridges. Moreover, IBs with thick, stub abutments supported by steel H piles oriented to bend about their strong axis driven in loose to medium dense sand are observed to have better seismic performance. The level of backfill compaction is found to have no influence on the seismic performance of IBs.

Short span bridges are commonly used throughout the United States to span small waterways and highway overpasses. New technologies in the civil engineering industry have aided in the creation of many unique designs of these short span highway bridges in efforts to decrease construction cost, decrease maintenance costs, increase efficiency, increase constructability, and increase safety. Three innovative systems, the Integral Abutment Bridge, “Bridge-in-a-Backpack”, and the Folded Plate Girder bridge will be analyzed to study how the bridges behave under various types of loading. Detailed finite element models were created for integral abutment bridges of varying geometry. These models are used to study how the live load distribution transversely across the bridge is effected by varying geometric properties and varying modeling techniques. These models will also be used to determine live load distribution factors for the integral abutment bridges and compare them to current American Association of State Highway and Transportation Officials specifications. The “Bridge-in-a-Backpack” and the Folded Plate Girder bridges were each constructed with a variety of instruments to measure the bridge movements. Readings from these instruments are used to determine the bridge response under various loading conditions. Bridges were analyzed during their construction process, during static live load testing, and during long term seasonal changes. The results from these studies will aid in the refinement of these innovative designs.

The Hampton Roads Bridge-Tunnel is one of the oldest prestressed concrete structures in the United States. The 3.5 mile long twin structure includes the world's first underwater tunnel between two man-made islands. Throughout its 60 years in service, the harsh environment along the Virginia coast has taken its toll on the main load carrying girders. Concrete spalling has exposed prestressing strands within the girders allowing corrosion to spread. Some of the more damaged girders have prestressing strands that have completely severed due to the extensive corrosion. The deterioration has caused select girders to fail the necessary load ratings. The structure acts as an evacuation route for the coast and is a main link for the local Norfolk Naval Base and surrounding industry. Because of these constraints, load posting is not a viable option. Live load testing of five spans was performed to investigate the behavior of the damaged spans. Innovative techniques were used during the load test including a wireless system to measure strains. Two different deflection systems were implemented on the spans, which were located about one mile offshore. The deflection data was later compared head to head. From the load test results, live load distribution factors were developed for both damaged and undamaged girders. The data was also used by the local Department of Transportation to validate computer models in an effort to help pass the load rating. Overall, this research was at the forefront of the residual strength of prestressed concrete girders and the testing of in-service bridges. / Master of Science

The inverted T-beam bridge system provides an accelerated bridge construction alternative for short-to-medium-span bridges. The system consists of adjacent precast inverted T-beams finished with a cast-in-place concrete topping. The system offers enhanced performance against reflective cracking, and reduces the likelihood of cracking due to time dependent effects. The effects of transverse bending due to concentrated wheel loads are investigated with respect to reflective cracking. Transverse bending moment are quantified and compared to transverse moment capacities provided by a combination of various cross-sectional shapes and transverse connections. A design methodology for transverse bending is suggested. Tensile stresses created due to time dependent and temperature effects are quantified at the cross-sectional and structure level and strategies for how to alleviate these tensile stresses are proposed. Because differential shrinkage is believed to be one of the causes of deck cracking in composite bridges, a study on shrinkage and creep properties of seven deck mixes is presented with the goal of identifying a mix whose long terms properties reduce the likelihood of deck cracking. The effects of differential shrinkage at a cross-sectional level are numerically demonstrated for a variety of composite bridge systems and the resistance of the inverted T-beam system against time dependent effects is highlighted. End stresses in the end zones of such a uniquely shaped precast element are investigated analytically in the vertical and horizontal planes. Existing design methods are evaluated and strut-and-tie models, calibrated to match the results of 3-D finite element analyses, are proposed as alternatives to existing methods to aid designers in sizing reinforcing in the end zones. Composite action between the precast beam and the cast-in-place topping is examined via a full scale test and the necessity of extended stirrups is explored. It is concluded that because of the large contact surface between the precast and cast-in-place elements, cohesion alone appears to provide the necessary horizontal shear strength to ensure full composite action. Live load distribution factors are quantified analytically and by performing four live loads tests. It is concluded that AASHTO's method for cast-in-place slab span bridges can be conservatively used in design. / Ph. D.

Accelerated Bridge Construction (ABC) has gained substantial popularity in new bridge construction and bridge deck replacement because it offers innovative construction techniques that result in time and cost savings when compared to traditional bridge construction practice. One technology commonly implemented in ABC to effectively execute its projects is the use of prefabricated bridge components (precast/prestressed bridge components). Precast/prestressed bridge components are fabricated offsite or near the site and then connected on-site using small volume closure pour connections. Diaphragms are also commonly used to strengthen the connection between certain prefabricated components used in ABC, such as beam elements. Bridges containing closure pour connections and diaphragms can be designed using AASHTO LRFD live-load distribution factor formulas under the condition that the bridge must be sufficiently connected. However, these formulas were developed using analytical models that did not account for the effects of closure pours and diaphragms on live-load distribution. This research study investigates live-load distribution characteristics of precast/prestressed concrete bridges with closure pour connections and diaphragms. The investigation was conducted using finite element bridge models with closure pour joints that were calibrated using experimental data and different configuration of diaphragms. The concrete material used for the closure pour connections was developed as part of a larger project intended to develop high early-strength concrete mixtures that specifically reach strength in only 12 hours, a critical requirement for ABC projects.

The topic of this Thesis is a study of the behavior of flexible metal large-span culverts during the construction and the operation. The aim is to analyze the behavior of the structure as a result of an unequally dropping support and a position of the load to the construction in relation to the soil cover height above the top of the steel construction. The Thesis is theoretical and based on the numerical parametric study.

Adjacent precast, prestressed box beam bridges have a history of poor performance and have been observed to exhibit common types of deterioration including longitudinal cracking, concrete spalling, and deterioration of the concrete top flange. The nature of these types of deterioration leads to uncertainty of the extent and effect of deterioration on structural behavior. Due to limitations in previous research and understanding of the strength of deteriorated box beam bridges, conservative assumptions are being made for the assessment and load rating of these bridges. Furthermore, the design of new box beam bridges, which can offer an efficient and economical solution, is often discouraged due to poor past performance. Therefore, the objective of this research is to develop improved recommendations for the inspection, load rating, and design of adjacent box beam bridges. Through a series of bridge inspections, deteriorated box beams were identified and acquired for experimental testing. The extent of corrosion was determined through visual inspection, non-destructive evaluation, and destructive evaluation. Non-destructive tests (NDT) included the use of connectionless electrical pulse response analysis (CEPRA), ground penetrating radar (GPR), and half-cell potentials. The deteriorated capacity was determined through structural testing, and an analysis procedure was developed to estimate deteriorated behavior. A rehabilitation procedure was also developed to restore load transfer of adjacent beams in cases where shear key failures are suspected. Based on the understanding of deterioration developed through study of deteriorated adjacent box beam bridges, improved inspection and load rating procedure are provided along with design recommendations for the next generation of box beam bridges.