International Telemetering Conference Proceedings / October 20-23, 2003 / Riviera Hotel and Convention Center, Las Vegas, Nevada / Phase-locked loop (PLL) frequency synthesizers used for high-speed data transmission must rapidly hop and lock to new frequencies. The fundamental problem is that the settling time depends inversely on the loop bandwidth, and increasing the bandwidth causes unwanted noise interference and stability problems for the circuit. We demonstrate the feasibility of replacing the analog integrator in the PLL with a digital integrator. This circuit has advantages of increased hopping speed, ability to compensate for temperature drift and system stability. PLL lock-in was demonstrated in a prototype circuit designed and built with both discrete components and with a programmable logic device.

International Telemetering Conference Proceedings / October 22-25, 2001 / Riviera Hotel and Convention Center, Las Vegas, Nevada / This paper describes techniques on the microwave FM locked in phase of transmitters in the reentry telemetry system. A few scheme configurations on the microwave FM locked in phase, its circuit characteristics and applications are analyzed. Research results show that the two-point injection microwave FM locked in phase is suitable for the telemetry system, which code rate is higher, band of wide, and modulation response very well.

International Telemetering Conference Proceedings / October 26-29, 1998 / Town & Country Resort Hotel and Convention Center, San Diego, California / Presentation for ITC 98 of Alcatel Espace last studies and developments regarding TTC Products This document lays on 3 parts: · a technical point of view · a technology/design description · a synthesis showing main performance and results

A photonic analog-to-digital converter (ADC) based on a robust symmetrical number system (RSNS) was constructed and tested. The analog signal to be converted is used to amplitude modulate an optical pulse from a laser using three Mach-Zehnder interferometers (MZI). The Mach-Zehnder interferometers fold the input analog signal for a three-channel RSNS encoding. The folding waveforms are then detected and amplitude-analyzed by three separate comparator banks, the outputs of which are used to determine a digital representation of the analog signal. This design uses the RSNS preprocessing to encode the signal with the fewest number of comparators for any selected bit resolution. In addition to the efficiency of its use of comparators, the RSNS encoding has inherent Gray-code properties making it particularly attractive for eliminating any possible encoding errors. The RSNS encoding is combined with an optical infrastructure that offers high bandwidth and low insertion loss characteristics. A full implementation was constructed and tested. The lack of a high-speed data acquisition device limited the results to examining the preprocessing and digital processing separately. With the system integration of a data acquisition device, a wideband direct digital antenna architecture can be demonstrated.

As a type of nonlinear system with complexity, mode-locked fiber lasers are known for their complex behaviour. It is a challenging task to understand the fundamental physics behind such complex behaviour, and a unified description for the nonlinear behaviour and the systematic and quantitative analysis of the underlying mechanisms of these lasers have not been developed. Here, we present a complexity science-based theoretical framework for understanding the behaviour of mode-locked fiber lasers by going beyond reductionism. This hierarchically structured framework provides a model with variable dimensionality, resulting in a simple view that can be used to systematically describe complex states. Moreover, research into the attractors' basins reveals the origin of stochasticity, hysteresis and multistability in these systems and presents a new method for quantitative analysis of these nonlinear phenomena. These findings pave the way for dynamics analysis and system designs of mode-locked fiber lasers. We expect that this paradigm will also enable potential applications in diverse research fields related to complex nonlinear phenomena.

Data conversion is the crucial interface between the real world and digital processing systems. Analogue-to-digital converters and digital-to-analogue converters are two key conversion devices and used as the interface. Up to now, the conventional ADCs based on Nyquist sampling theorem are facing a critical challenge: the resolution and the sampling rate must be radically increased when some applications such as radar detection and ultra-wideband communication emerge. The offset of comparators and the setup time of sample-and-hold circuits, however, limit the resulution and clock rate of ADCs. Alternatively, in some applications such as speech, temperature sensor, etc. signals remain possibly unchanged for prolonged periods with brief bursts of significant activity. If trational ADCs are employed in such circumstances a higher bandwidth is required for transmitting the converted samples. On the other hand, sampling signals with an extremely high clock rate are also required for converting the signals with the feature of sparsity in time domain. The level-crossing sampling scheme (LCSS) is one of the data conversions suitable for converting signals with the sparsity feature and brief bursts of signigicant activity. due to the traditional LCSS with a fixed clock rate being limited in applications a novel irregular data conversion scheme called analogue-to-information system (AIS) is proposed in this thesis. The AIS is typically based upon LCSS, but an adjustable clock generator and a real time data compression scheme are applied to it. As the system-level simulations results of AIS show it can be seen that a data transmission saving rate nearly 30% is achieved for different signals. PLLs with fast pull-in and locking schemes are very important when they are applied in TDMA systems and fequency hopping wireless systems. So a novel triple path nonlinear phase frequency detector (TPNPFD) is also proposed in this thesis. Compared to otherPFDs, the pll-in and locking time in TPNPFD is much shorter. A proper transmission data format can make the recreation of the skipped samples and the reconstruction of the original signal more efficient, i.e. they can be achieved in a minimum number of the received data without increasing much more hardware complexity. So the preliminary data format used for transmitting the converted data from AIS is also given in the final chapter of this thesis for future works.

Solid-state lasers are capable of providing versatile output characteristics with greater flexibility compared to other popular laser systems. Lasing action has been achieved in many hundreds of solid-state media, but Nd-ion doped gain media are widely used to reach high power levels with short pulses. In this work, commercially available Nd:KGW crystal served as a gain medium to achieve pulsed operation at 1067 nm. This laser crystal offers large stimulated emission crosssection and gain bandwidth which facilitates generation of high peak power pulses in the picosecond regime. The KGW crystal is monoclinic and biaxial in structure, and anisotropic in its optical and thermal properties. Due to poor thermal conductivity, this crystal can be operated within a limited power range before crystal fracture takes place. To reduce the amount of heat deposited in the gain media, we introduced a new pumping wavelength of 910 nm which reduces the quantum defect by more than 45%. Continuous-wave laser operation was optimized to operate in mode-locked regime. In order to achieve short light pulses from the continuous-wave laser, one of the end mirrors was replaced by a semiconductor saturable absorber mirror (SESAM) to generate 2.4 ps pulses at a repetition rate of 83.8 MHz. An average output power of 87 mW was obtained at lasing wavelength of 1067 nm and the beam was nearly diffraction limited with M^2 < 1.18. The peak power of the generated pulses was 427 W and energy of each pulse was >1 nJ. Pumping the crystal at longer wavelength (910 nm) reduced the thermal lensing of the crystal by half when compared to conventional pumping at shorter wavelength (808 nm). To the best of our knowledge, this is the first time passive mode-locking of a Nd:KGW laser was explored using the pump wavelength at 910 nm. / February 2017

by Kwok Chi Wing. / Thesis (M.Phil.)--Chinese University of Hong Kong, 1993. / Includes bibliographical references. / Abstract / Acknowledgements / Chapter 1. --- Introduction --- p.1 / Chapter 2. --- Basic Concepts of Lasers and Simple Survey of Laser Theories --- p.4 / Chapter 2.1 --- Introduction --- p.4 / Chapter 2.1.1 --- Basic Structure of a Laser --- p.4 / Chapter 2.1.2 --- "Concepts of "" Mode"" arid "" Mode-Locking""" --- p.6 / Chapter 2.2 --- Brief Review of Laser Theories --- p.9 / Chapter 2.3 --- Other Simple Models --- p.12 / Chapter 2.4 --- Review of the Maxwell-Bloch Equations --- p.17 / Chapter 2.4.1 --- Derivation of Maxwell-Bloch Equations --- p.17 / Chapter 2.4.2 --- Continuous-Wave Operation --- p.23 / Chapter 2.4.3 --- Mean-Field Approximation and Lorenz-Haken Instability --- p.24 / Chapter 2.4.4 --- Adiabatic Elimination of Fast Variables --- p.26 / Chapter 2.4.5 --- Thin-Sheet-Gain Approximation for Multimode Lasers --- p.30 / Chapter 2.4.6 --- Self-Mode-Locking Predicted by Using Maxwell-Bloch Equations --- p.33 / Chapter 2.4.7 --- Hysteresis Phenomena in Switching the Cavity Detuning --- p.35 / Chapter 3. --- "Moving-Mirror ""Mode-Locking""" --- p.41 / Chapter 3.1 --- Conventional Laser Mode-Locking --- p.41 / Chapter 3.1.1 --- Preliminaries： What is Mode-Locking (Conventional) ？ --- p.41 / Chapter 3.1.2 --- Active Mode-Locking and Passive Mode-Locking --- p.43 / Chapter 3.1.3 --- Spectra of Conventional Mode-Locked Lasers --- p.49 / Chapter 3.2 --- Moving-Mirror Mode-Locking --- p.50 / Chapter 3.2.1 --- Historical Notes --- p.50 / Chapter 3.2.2 --- Previously Proposed Explanations --- p.54 / Chapter 3.3 --- MMML Mechanism: our Proposal --- p.59 / Chapter 3.3.1 --- Relation between MMML Lasers and FSFC Lasers --- p.60 / Chapter 3.3.2 --- Concept of Moving Modes --- p.62 / Chapter 3.3.3 --- How are the Moving Modes Locked ？ --- p.64 / Chapter 3.4 --- Numerical Simulations ´ؤ Method and Results --- p.68 / Chapter 3.4.1 --- Description of Our Numerical Model --- p.68 / Chapter 3.4.2 --- Tests on the Simulation Method --- p.71 / Chapter 3.4.3 --- Ultrashort Pulses Generation of a MMML Laser --- p.73 / Chapter 3.4.4 --- Modulation of the Pulses --- p.74 / Chapter 3.4.5 --- Broadband or Discrete Spectra ？ --- p.75 / Chapter 3.4.6 --- Different Operation Regimes in MMML Lasers --- p.79 / Chapter 3.4.7 --- Why Period-T/2 Pulses --- p.84 / Chapter 3.4.8 --- Auto-Correlation Function of the Electric Field --- p.86 / Chapter 3.4.9 --- FSFC Laser with Injection Signal --- p.87 / Chapter 3.4.10 --- MMML in Class C Laser: d = 1.0 --- p.88 / Chapter 3.4.11 --- Exciting the Relaxation Oscillation Resonance --- p.89 / Chapter 4. --- Discussion and Conclusion --- p.92 / Chapter 4.1 --- Limitation of (Conventional) Thin-Sheet-Gain Approximation --- p.92 / Chapter 4.1.1 --- Problem with the Conventional Thin -Sheet-Gain Approximation --- p.92 / Chapter 4.1.2 --- Modified Thin-Sheet-Gain Approximation --- p.93 / Chapter 4.2 --- Concluding Remarks; Possibilities of Further Research --- p.97 / References and Notes / Appendix: Source Codes of the Fortran Program

by Chi Sang Wong. / Thesis (M.Phil.)--Chinese University of Hong Kong, 1999. / Includes bibliographical references. / Abstract also in Chinese. / Abstract --- p.ii / Acknowledgements --- p.vii / Table of Contents --- p.viii / Chapter 1 --- Introduction --- p.1 / Chapter 1.1 --- Background --- p.1 / Chapter 1.2 --- Organisation of Thesis --- p.4 / References --- p.6 / Chapter 2 --- Principles and Theories --- p.8 / Chapter 2.1 --- Device Concepts --- p.9 / Chapter 2.2 --- Picosecond Photoconductors --- p.14 / Chapter 2.3 --- Photoconducting Antennas --- p.18 / Chapter 2.4 --- Summary --- p.20 / References --- p.21 / Chapter 3 --- Self-mode-locked Ti:sapphire (Ti:Al203) Laser --- p.24 / Chapter 3.1 --- Introduction --- p.25 / Chapter 3.2 --- Self-mode-locked Ti:sapphire Laser Cavity --- p.26 / Chapter 3.3 --- Negative Dispersion Using Pairs of Prisms --- p.28 / Chapter 3.4 --- Kerr-lens Mode-Locked Model: Role of Space-time Effects --- p.33 / Chapter 3.5 --- Initiation of Self-mode-locked Pulses --- p.37 / Chapter 3.6 --- 39-fs Pulses from A Self-mode-locked Ti:sapphire Laser --- p.38 / Chapter 3.7 --- Summary --- p.42 / References --- p.43 / Chapter 4 --- Photoconductive Detection of Millimetre Waves Using LT-GaAs --- p.46 / Chapter 4.1 --- Introduction --- p.47 / Chapter 4.2 --- Devices Structures --- p.48 / Chapter 4.3 --- Experimental Setup --- p.52 / Chapter 4.4 --- Results and Discussion --- p.54 / Chapter 4.5 --- Summary --- p.57 / References --- p.58 / Chapter 5 --- Investigation of Other Materials for THz Detection --- p.60 / Chapter 5.1 --- Introduction --- p.61 / Chapter 5.2 --- Material Preparation --- p.62 / Chapter 5.3 --- Devices Structures --- p.64 / Chapter 5.4 --- Experimental Setup --- p.68 / Chapter 5.5 --- Results and Discussion --- p.69 / Chapter 5.6 --- Investigation of Other Materials --- p.72 / Chapter 5.7 --- Summary --- p.73 / References --- p.74 / Chapter 6 --- Characteristics of Millimetre Waves --- p.76 / Chapter 6.1 --- Introduction --- p.77 / Chapter 6.2 --- Experimental Setup --- p.78 / Chapter 6.3 --- Experimental Results --- p.80 / Chapter 6.4 --- Experimental Setup --- p.83 / Chapter 6.5 --- Experimental Results --- p.85 / Chapter 6.6 --- Summary --- p.86 / References --- p.87 / Chapter 7 --- Conclusion and Future Work --- p.88 / Chapter 7.1 --- Conclusion --- p.88 / Chapter 7.2 --- Future Work --- p.91 / Appendixes --- p.A-l / Chapter Appendix A: --- Hall Effect Measurement System --- p.A-l / Chapter Appendix B: --- Photography of Device Structures --- p.A-2 / Chapter Appendix C: --- Fast Fourier Transform Program --- p.A-3 / Chapter Appendix D: --- List of Publications --- p.A-4

Active mode locking is one of the simplest ways to generate picosecond pulses at gigahertz repetition rates. In my works, I demonstrate the generation of picosecond pulses with a center-wavelength spanning from 1489nm to 1589nm using a polarization maintaining fiber loop mirror filter (PMF-LMF) in a mode-locked semiconductor optical amplifier (SOA) ring laser. By applying the SOA gain shifting technique and with the help of the controllable transmission ratio of the PMF-LMF, the tuning range of the output wavelength can be extended. By applying the technique of dispersion tuning, electrical wavelength tuning can be achieved across a range of 100nm. / Compared to the active mode-locking method, the regenerative mode-locking is very convenient because it does not require any external source for modulation and is proved to be more robust against fluctuations in ambient temperature. We demonstrate a 10-GHz regeneratively mode-locked fiber laser using a PMF-LMF. The operating frequency is determined by the free-spectral-range of the PMF-LMF and the component is extracted optically from the ring laser output. / In addition, we also demonstrate a simple technique to generate wavelength tunable picosecond pulses at adjustable repetition rate without using electrical or optical RF filter to extract the radio frequency (RF). The RF signal for mode locking is generated from a Fabry-Perot laser diode (FP-LD) under optical injection. The output frequency can be varied by adjusting the biasing current of the FP-LD. (Abstract shortened by UMI.) / Picosecond optical pulse sources with broad tunability and various repetition rates are key elements for applications in wavelength- and time-division multiplexed optical transmission systems. Mode-locking is one of the main techniques for the generation of optical pulses with high repetition rate picosecond pulse trains. This thesis presents our research efforts in high repetition rate optical pulse generation using active and regenerative mode-locking techniques, and a self-starting approach. We also demonstrate the application of harmonic mode locking in all-optical clock recovery from NRZ data. / Tang Wing Wa. / "August 2005." / Adviser: C. T. Shu. / Source: Dissertation Abstracts International, Volume: 67-07, Section: B, page: 4015. / Thesis (Ph.D.)--Chinese University of Hong Kong, 2005. / Includes bibliographical references. / Electronic reproduction. Hong Kong : Chinese University of Hong Kong, [2012] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Electronic reproduction. [Ann Arbor, MI] : ProQuest Information and Learning, [200-] System requirements: Adobe Acrobat Reader. Available via World Wide Web. / Abstract in English and Chinese. / School code: 1307.