Work is focused on theoretic analisis of manufacturing precise shears tools by unconventional technology closely focused on wire electro discharge machining consideration operation costs of this metod.It is discribing development of this method, machines and tools for electrical discharge machining. It is mention facts influencing quality of cut surface during manufacturing of cutting tools, strategy of cutting workpiece, stage and quality of surface layer after WEDM as long with economic viewpoint and benefits of WEDM technology.

In this work, description of a basic principle of electro discharge machining and its technological possibilities was made. Possibilities of individual EDM machine producers and their comparison were described. Furthermore, the use of electro discharge machining in Zdas a.s. was shown. Trends in a development of the electro discharge technology are included, too.

This thesis deals with design for manufacturing technology single part on machine FS, which is the connecting part. Work deals with the material of this component, therefore, cast iron with lamellar graphite, the properties of this material, primarily focusing on the machinability. Due to the shape and dimensions of the workpiece is also described problems cutting of box parts, the most common operations used in their manufacture, including cutting tools and materials. These findings are then applied in terms of the company TOS Kuřim - OS a.s. An analysis of current manufacturing technology and design is made for its amendment. In conclusion with the technical-economic evaluation.

The aim of this thesis is the design of the rotary tilting table controlled the fourth and fifth axis for CNC centrum.První part includes the search for pivotally tilting tables. The second part includes the choice of technical paremetrů pivotally tilting table for selected CNC center, design of possible options , selection of appropriate options, design of the selected option.

Direct Machining And Control (DMAC) is a new method of controlling machine tools directly from process planning software. A motion planning module is developed for the DMAC system that operates directly off path geometry without pre-tessellation. The motion planner is developed with the intent to process Bezier curves. The motion planning module includes a deterministic predictor-corrector-type curve interpolator, a dynamics limiting module, and a two-pass jerk-limited speed profiling algorithm. The methods are verified by machining an automotive surface in a clay medium and evaluating the resultant machine dynamics, feed rate, and chordal error throughout the machining process.

No description available.

<p>Carbon fiber bending during Carbon Fiber Reinforced Plastic (CFRP) milling is an important factor on the quality of the machined surface. When the milling tool rotates, the fiber first contacts the rake face instead of the tool edge at a certain cutting angle, then the fiber is bent instead of being cut by the tool. It causes the matrix and the fiber to fall out, and the fiber is broken from deep inside the machined surface. The broken fibers are pulled out as the tool rotates, which is known as pull-out fibers. The machining defect is the main cause of deteriorating the quality of the machined surface. To reduce such machining defects, it is important to predict the carbon fiber bending during CFRP milling. However, it is difficult to determine a point where fiber bending occurs because the fiber cutting angle changes every moment as the tool rotates. Therefore, in this study, CFRP milling simulation was performed to numerically analyze the machining parameters such as fiber cutting angle, fiber length, and the magnitude of fiber bending according to the different milling conditions. In addition, the deformation of the matrix existing between carbon fibers is predicted based on the fiber bending information obtained through simulation, and matrix shear strain energy model is developed. Also, the relationship between the matrix shear strain energy and machining quality is analyzed. Through verification experiments under various machining conditions, it is confirmed that the quality of the machined surface deteriorated as the matrix shear strain energy increased. Moreover, this study analyzed the fiber cutting mechanism considering bent fibers during CFRP milling and proposed a method to identify the type of machining mechanism through machining sound analysis. Through experiments, it was verified that fiber bending or defects can be identified through machining sound analysis in the high-frequency range between 7,500 Hz and 14,800 Hz. From the analysis, the effect of different chip thickness in up-milling and down-milling on fiber bending was investigated by analyzing simulation and sound signal. From machining experiments, the effect of this difference on cutting force and machining quality was verified. Lastly, we developed a minimum chip thickness and fiber fracture model in CFRP milling and analyzed the effect of fractured fibers on the machining sound. Carbon fibers located below the minimum chip thickness do not contact the tool edge and are compressed by the bottom face of the tool, and these fibers are excessively bent and broken. As these broken fibers are discharged while scratching the flank face of the tool, a loud machining sound is generated. Moreover, through the verification experiment, it was confirmed that the number of broken fibers is proportional to the loudness of the sound, and calculated number of broken fibers for one second using the fiber fracture model coincides with the high-frequency machining sound range of 7,500 Hz to 14,800 Hz.</p>

Doctor of Philosophy / Department of Industrial & Manufacturing Systems Engineering / Shuting Lei / Laser-assisted machining (LAM) is a promising non-conventional machining technique for advanced ceramics. However, the fundamental machining mechanism which governs the LAM process is not well understood so far. Hence, the main objective of this study is to explore the machining mechanism and provide guidance for future LAM operations. In this study, laser-assisted milling (LAMill) of silicon nitride ceramics is focused. Experimental experience reveals that workpiece temperature in LAM of silicon nitride ceramics determines the surface quality of the machined workpiece. Thus, in order to know the thermal features of the workpiece in LAM, the laser-silicon nitride interaction mechanism is investigated via heating experiments. The trends of temperature affected by the key parameters (laser power, laser beam diameter, feed rate, and preheat time) are obtained through a parametric study. Experimental results show that high operating temperature leads to low cutting force, good surface finish, small edge chipping, and low residual stress. The temperature range for brittle-to-ductile transition should be avoided due to the rapid increase of fracture toughness. In order to know the temperature distribution at the cutting zone in the workpiece, a transient three-dimensional thermal model is developed using finite element analysis (FEA) and validated through experiments. Heat generation associated with machining is considered and demonstrated to have little impact on LAM. The model indicates that laser power is one critical parameter for successful operation of LAM. Feed and cutting speed can indirectly affect the operating temperatures. Furthermore, a machining model is established with the distinct element method (or discrete element method, DEM) to simulate the dynamic process of LAM. In the microstructural modeling of a β-type silicon nitride ceramic, clusters are used to simulate the rod-like grains of the silicon nitride ceramic and parallel bonds act as the intergranular glass phase between grains. The resulting temperature-dependent synthetic materials for LAM are calibrated through the numerical compression, bending and fracture toughness tests. The machining model is also validated through experiments in terms of cutting forces, chip size and depth of subsurface damage.

Thesis (MScEng (Mechanical and Mechatronic Engineering))--University of Stellenbosch, 2011. / ENGLISH ABSTRACT: The purpose of this study is to investigate the machinability of commercially pure (CP) titanium, manufactured using the press-and-sinter PM process. To this end, CP titanium powder (-200 mesh) was compacted and sintered in vacuum (10-4 torr) for two hours at 1200°C. Small cylindrical samples were compacted at pressures varying from 350 to 600 MPa in order to determine the compressibility of the powder. Following these tests, four larger stepped-cylinder samples were compacted at pressures close to 400 MPa and sintered under similar conditions. These samples had sintered densities varying between 3.82 and 4.41 g/cm3. They were used to evaluate the machinability of the sintered titanium using face turning machining tests. The samples were machined dry, using uncoated carbide (WC-Co) cutting tool. Cutting speeds between 60-150 m/min were evaluated while keeping the feed rate and depth of cut constant at 0.15 mm/rev and 0.5 mm, respectively. The final machined surface finish and the tool wear experienced during the face turning machining tests were monitored in order to evaluate PM titanium’s machining performance. This study showed that it is possible to use the press-and-sinter PM process with CP titanium powder, with a particle size of less than 75 μm (-200 mesh), to manufacture sintered titanium. However, particle shape influences the compressibility of the powder and pressing parts of larger volume, such as the machining test sample shape, is challenging when using such small particle size powder. Processing conditions, such as compaction pressure, sintering temperature and sintering time, influence the sintered density. Results from the machinability tests show that tool wear increases with a decrease in the porosity of the sintered titanium. A more porous sintered material has both lower strength and thermal conductivity. As these factors have opposing effects on the machinability of materials, it is concluded that the strength of the sintered titanium has a stronger influence on its machinability than the thermal conductivity. The cutting tool wear was uniform but showed indications of crater wear. The machined surface of the denser parts had minimal defects compared to less dense parts. Chip shape is long for the dense parts, and spiral for the less dense parts. The chips formed were all segmented, which is typical for titanium. The machinability of the sintered CP titanium was compared to that of wrought titanium alloys. As expected, it was found that the machinability of the sintered titanium was poor in comparison. / AFRIKAANSE OPSOMMING: Die doel van hierdie studie is om die masjineerbaarheid van kommersieel suiwer (KS) titaan, wat deur die pers-en-sinter poeiermetallurgie (PM) metode vervaardig word, te ondersoek. Om hierdie doel te bereik, is KS titaan poeier (-200 ogiesdraad) gekompakteer en gesinter in ‘n vakuum (10-4 torr) teen 1200°C vir 2 ure. Klein silindriese monsters is tussen drukke van 350en 600 MPa gekompakteer om die samedrukbaarheid van die poeier te bepaal. Na aanleiding van hierdie toetse, is vier groter trapvormige-silinder monsters by drukke naby aan 400MPa gekompakteer en onder soortgelyke omstandighede gesinter. Hierdie monsters het gesinterde digthede tussen 3.82 en 4.41 g/cm3 gehad. Hulle is gebruik om die masjineerbaarheid van die gesinterde titaan te ondersoek deur middel van vlak-draai masjineringstoetse. Die monsters is sonder smeermiddel gemasjineer met onbedekte karbied (WC-Co) snygereedskap. Snysnelhede tussen 60 – 150 m/min is geëvalueer terwyl die voertempo en diepte van die snit konstant by 0.15 mm/rev en 0.5 mm, onderskeidelik, gehou is. Die finale gemasjineerde oppervlak afwerking en gereedskapsslytasie tydens die vlak-draai masjinering toets is van die faktore wat gemonitor is sodat PM titaan se optrede tydens masjinering geëvalueer kan word. Hierdie studie wys dat diepers-en-sinter metode wel met KS titaan poeier, met ‘n partikel grootte van minder as 75 μm (-200 maas), gebruik kan word om gesinterde titaan te vervaardig. Die partikelgrootte beïnvloed wel die samedrukbaarheid van die poeier. Die samedrukking van parte met groter volume, soos bv die masjinerings toetsmonster, is uitdagend wanneer klein partikelgrootte poeier gebruik word. Proses omstandighede, soos kompaksie druk, sinteringstemperatuur en sinteringstyd, beïnvloed die gesinterde digtheid. Resultate van die masjineerbaarheidstoetse wys dat beitelslytasie toeneem met ‘n afname in porositeit van die gesinterede titaan. ‘n Meer poreus gesinterde materiaal het beide laer sterkte en termiese geleidingsvermoë. Aangesien hierdie faktore teenoorgestelde uitwerkings op masjineerbaarheid het, word dit dan afgelei dat die sterkte van gesinterde titaan ‘n groter invloed het op sy masjineerbaarheid as die termiese geleidingsvermoë. Die beitel se slytasie is hoofsaahlik, maar het tekens van kraterslytasie getoon. Die gemasjineerde oppervlak van die meer digte onderdele of toetsmonters het min gebreke gehad in vergelyking met die minder digte dele. Die vorm van die spaanders is lank vir digte parte, en spiraalvormig vir minder digte toetsmonsters. Die spaanders wat gevorm het, was almal gesegmenteerd, wat tipies is vir titaan. Die masjineerbaarheid van die gesinterde KS titaan is met dié van gesmede titaanallooie vergelyk. Soos verwag is, is gevind dat die masjineerbaarheid van die gesinterde titaan in vergelyking swak is.

Surface integrity of manufactured components has a critical impact on their functional performance. Magnesium alloys are lightweight materials used in the transportation industry and are also emerging as a potential material for biodegradable medical implants. However, the unsatisfactory corrosion performance of Mg alloys limits their application to a great extent. Surface integrity factors, such as grain size, crystallographic orientation and residual stress, have been proved to remarkably influence the functional performance of magnesium alloys, including corrosion resistance, wear resistance and fatigue life. In this dissertation, the influence of machining conditions, including dry and cryogenic cooling (liquid nitrogen was sprayed to the machined surface during machining), cutting edge radius, cutting speed and feed rate, on the surface integrity of AZ31B Mg alloy was investigated. Cryogenic machining led to the formation of a "featureless layer" on the machined surface where significant grain refinement from 12 μm to 31 nm occurred due to dynamic recrystallization (DRX), as well as increased intensity of basal plane on the surface and more compressive residual stresses. Dry and cryogenic burnishing experiments of the same material were conducted using a fixed roller setup. The thickness of the processed-influenced layer, where remarkable microstructural changes occurred, was dramatically increased from the maximum value of 20 μm during machining to 3.4 mm during burnishing. The burnishing process also produced a stronger basal texture on the surface than the machining process. Preliminary corrosion tests were conducted to evaluate the corrosion performance of selected machined and burnished AZ31B Mg samples in 5% NaCl solution and simulated body fluid (SBF). Cryogenic cooling and large edge radius tools were found to significantly improve the corrosion performance of machined samples in both solutions. The largest improvement in the material's corrosion performance was achieved by burnishing. A finite element study was conducted for machining of AZ31B Mg alloy and calibrated using the experimental data. A user subroutine was developed and incorporated to predict the grain size changes induced by machining. Good agreements between the predicted and measured grain size as well as thickness of featureless layers were achieved. Numerical studies were extended to include the influence of rake angle, feed rate and cutting speed on the featureless layer formation.