Many modeling studies have been carried out to simulate the current distribution across the channel and shoulder direction in a proton exchange membrane (PEM) fuel cell. However the modeling results do not show agreement on the current density distribution. At the same time, no experimental measurement result of current density distribution across the channel and the shoulder direction is available to testify the modeling studies. Hence in this work, an experiment was conducted to separately measure the current densities under the channel and the shoulder in a PEM fuel cell by using the specially designed membrane electrode assemblies. The experimental results show that the current density under the channel is lower than that under the shoulder except when the fuel cell load is high. Afterwards two more experiments were carried out to find out the reason causing the higher current density under the shoulder. The effects of the electric resistance of gas diffusion layer (GDL) in the lateral and through-plane directions on the current density distribution were studied respectively. The experimental results show that it is the through-plane electric resistance that leads to the higher current density under the shoulder. Moreover, a three-dimensional fuel cell model is developed using FORTRAN. A new method of combining the thin-film model and homogeneous model is utilized to model the catalyst layer. The model is validated by the experimental data. The distribution of current density, oxygen concentration, membrane phase potential, solid phase potential and overpotential in a PEM fuel cell have been studied by the model. The modeling results show that the new modeling method provides better simulations to the actual transport processes and chemical reaction in the catalyst layer of a PEM fuel cell.

Le bicarbonate de soude raffiné, produit industriellement par la société Solvay, est fabriqué dans des colonnes à bulles de grande taille, appelées les colonnes BIR. Dans ces colonnes, une phase gazeuse contenant un mélange d’air et dioxyde de carbone (CO2) est dispersée sous forme de bulles dans une solution aqueuse de carbonate et de bicarbonate de sodium (respectivement Na2CO3 et NaHCO3). Cette dispersion donne lieu à un transfert de CO2 des bulles vers la phase liquide. Au sein des colonnes, la phase gazeuse se répartit dans deux populations de bulles : des petites bulles (diamètre de quelques mm) et des grandes bulles (diamètre de quelques cm). Le transfert bulle-liquide de CO2 est couplé à des réactions chimiques prenant place en phase liquide, qui conduisent à la conversion du Na2CO3 en NaHCO3. Une fois la concentration de saturation dépassée, le NaHCO3 précipite sous forme de cristaux et un mélange liquide-solide est recueilli à la sortie de ces colonnes. Ce travail, réalisé en collaboration avec la société Solvay, porte sur l’étude et la modélisation mathématique des phénomènes de transfert de matière entre phases, couplés à des réactions chimiques, prenant place au sein d’une colonne BIR. L’association d’études sur des colonnes à bulles à l’échelle industrielle ou réduite (pilote) et d’études plus fondamentales sur des dispositifs de laboratoire permet de développer une meilleure compréhension du fonctionnement des colonnes BIR et d’en construire un modèle mathématique détaillé. L’objectif appliqué de ce travail est la mise au point d’un modèle mathématique complet et opérationnel d’une colonne BIR. Cet objectif est supporté par trois blocs de travail, dans lesquels différents outils sont développés et exploités. Le premier bloc est consacré à la modélisation mathématique du transfert bulle-liquide de CO2 dans une solution aqueuse de NaHCO3 et de Na2CO3. Ce transfert est couplé à des réactions chimiques en phase liquide qui influencent sa vitesse. Dans un premier temps, des modèles sont développés selon des approches unidimensionnelles classiquement rencontrées dans la littérature. Ces approches passent par une idéalisation de l’écoulement du liquide autour des bulles. Une expression simplifiée de la vitesse du transfert bulle-liquide de CO2, est également développée et validée pour le modèle de colonne BIR. Dans un second temps, une modélisation complète des phénomènes de transport (convection et diffusion), couplés à des réactions chimiques, est réalisée en suivant une approche bidimensionnelle axisymétrique. L’influence de la vitesse de réactions sur la vitesse de transfert est étudiée et les résultats des deux approches sont également comparés. Le deuxième bloc est consacré à l’étude expérimentale du transfert gaz-liquide de CO2 dans des solutions aqueuses de NaHCO3 et de Na2CO3. A cette fin, un dispositif expérimental est développé et présenté. Du CO2 est mis en contact avec des solutions aqueuses de NaHCO3 et de Na2CO3 dans une cellule transparente. Les phénomènes provoqués en phase liquide par le transfert de CO2 sont observés à l’aide d’un interféromètre de Mach-Zehnder. Les résultats expérimentaux sont comparés à des résultats de simulation obtenus avec un des modèles unidimensionnels développés dans le premier bloc. De cette comparaison, il apparaît qu’une mauvaise estimation de la valeur de certains paramètres physico-chimiques apparaissant dans les équations de ce modèle conduit à des écarts significatifs entre les grandeurs observées expérimentalement et les grandeurs estimées par simulation des équations du modèle. C’est pourquoi une méthode d’estimation paramétrique est également développée afin d’identifier les valeurs numériques de ces paramètres physico-chimiques sur base des résultats expérimentaux. Ces dernières sont également discutées. Dans le troisième bloc, nous apportons une contribution à l’étude des cinétiques de précipitation du NaHCO3 dans un cristallisoir à cuve agitée. Cette partie du travail est réalisée en collaboration avec Vanessa Gutierrez (du service Matières et Matériaux de l’ULB). Nous contribuons à cette étude par le développement de trois outils : une table de calcul Excel permettant de synthétiser les résultats expérimentaux, un ensemble de simulations de l’écoulement au sein du cristallisoir par mécanique des fluides numérique et une nouvelle méthode d’extraction des cinétiques de précipitation du NaHCO3 à partir des résultats expérimentaux. Ces trois outils sont également utilisés de façon combinée pour estimer les influences de la fraction massique de solide et de l’agitation sur la cinétique de germination secondaire du NaHCO3. Enfin, la synthèse de l’ensemble des résultats de ces études est réalisée. Le résultat final est le développement d’un modèle mathématique complet et opérationnel des colonnes BIR. Ce modèle est développé en suivant l’approche de modélisation en compartiments, développée au cours du travail de Benoît Haut. Ce modèle synthétise les trois blocs d’études réalisées dans ce travail, ainsi que les travaux d’Aurélie Larcy (du service Transferts, Interfaces et Procédés de l’ULB) et de Vanessa Gutierrez. Les équations modélisant les différents phénomènes sont présentées, ainsi que la méthode utilisée pour résoudre ces équations. Des simulations des équations du modèle sont réalisées et discutées. Les résultats de simulation sont également comparés à des mesures effectuées sur une colonne BIR. Un accord raisonnable est observé. A l’issue de ce travail, nous disposons donc d’un modèle opérationnel de colonne BIR. Bien que ce modèle doive encore être optimisé et validé, il peut déjà être utilisé pour étudier l’effet des caractéristiques géométriques des colonnes BIR et des conditions appliquées à ces colonnes sur le comportement des simulations des équations du modèle et pour identifier des tendances. // The refined sodium bicarbonate is produced by the Solvay company using large size bubble columns, called the BIR columns. In these columns, a gaseous phase containing an air-carbon dioxyde mixture (CO2) is dispersed under the form of bubbles in an aqueous solution of sodium carbonate and sodium bicarbonate (Na2CO3 and NaHCO3, respectively). This dispersion leads to a CO2 transfer from the bubbles to the liquid phase. Inside these columns, the gaseous phase is distributed in two bubbles populations : small bubbles (a few mm of diameter) and large bubbles (a few cm of diameter). The bubble-liquid CO2 transfer is coupled with chemical reactions taking places in the liquid phase that leads to the conversion of Na2CO3 to NaHCO3. When the solution is supersaturated in NaHCO3, the NaHCO3 precipitates under the form of crystals and a liquid-solid mixture is extracted at the outlet of the BIR columns. This work, realized in collaboration with Solvay, aims to study and to model mathematically the mass transport phenomena between the phases, coupled with chemical reactions, taking places inside a BIR column. Study of bubble columns at the industrial and the pilot scale is combined to a more fundamental study at laboratory scale to improve the understanding of the BIR columns functioning and to develop a detailed mathematical modeling. The applied objective of this work is to develop a complete and operational mathematical modeling of a BIR column. This objective is supported by three blocks of work. In each block, several tools are developed and used. The first block is devoted to the mathematical modeling of the bubble-liquid CO2 transfer in an NaHCO3 and Na2CO3 aqueous solution. This transfer is coupled with chemical reactions in liquid phase, which affect the transfer rate. In a first time, mathematical models are developed following the classical one-dimensional approaches of the literature. These approaches idealize the liquid flow around the bubbles. A simplified expression of the bubble-liquid CO2 transfer rate is equally developed and validated for the BIR column model. In a second time, a complete modeling of the transport phenomena (convection and diffusion) coupled with chemical reactions is developed, following an axisymmetrical twodimensional approach. The chemical reaction rate influence on the bubble-liquid transfer rate is studied and the results of the two approaches are then compared. The second block is devoted to the experimental study of the gas-liquid CO2 transfer to NaHCO3 and Na2CO3 aqueous solutions. An experimental set-up is developed and presented. CO2 is put in contact with NaHCO3 and Na2CO3 aqueous solutions in a transparent cell. The phenomena induced in liquid phase by the CO2 transfer are observed using a Mach-Zehnder interferometer. The experimental results are compared to simulation results that are obtained using one of the one-dimensional model developed in the first block. From this comparison, it appears that a wrong estimation of some physico-chemical parameter values leads to significative differences between the experimentally observed quantities and those estimated by simulation of the model equations. Therefore, a parametric estimation method is developed in order to estimate those parameters numerical values from the experimental results. The found values are then discussed. In the third block is presented a contribution to the NaHCO3 precipitation kinetic study in a stirred-tank crystallizer. This part of the work is realized in collaboration with Vanessa Gutierrez (Chemicals and Materials Department of ULB). Three tools are developed : tables in Excel sheet to synthetize the experimental results, a set of simulations of the flow inside the crystallizer by Computational Fluid Dynamic (CFD) and a new method to extract the NaHCO3 precipitation kinetics from the experimental measurements. These three tools are combined to estimate the influences of the solid mass fraction and the flow on the NaHCO3 secondary nucleation rate. Finally, the synthesis of all these results is realized. The final result is the development of a complete and operational mathematical model of BIR columns. This model is developed following the compartmental modeling approach, developed in the PhD thesis of Benoît Haut. This model synthetizes the three block of study realized in this work and the studies of Aurélie Larcy (Transfers, Interfaces and Processes Department of ULB) and those of Vanessa Gutierrez. The equations modeling the phenomena taking place in a BIR column are presented as the used method to solve these equations. The equations of the model are simulated and the results are discussed. The results are equally compared to experimental measurement realized on a BIR column. A reasonable agreement is observed. At the end of this work, an operational model of a BIR column is thus developed. Although this model have to be optimized and validated, it can already be used to study the influences of the geometrical characteristics of the BIR columns and of the conditions applied to these columns on the behaviour of the model equation simulations and to identity tendencies.

Récemment, de nombreuses recherches ont été dévolues à la mise au point de réacteurs biphasiques, perçus comme une nouvelle technologie pour le traitement des polluants organiques dans les effluents gazeux. Ces réacteurs impliquent lutilisation dune seconde phase non aqueuse pour améliorer la solubilité et le transfert de masse des composés hydrophobes. Dans ce travail, nous avons développé un réacteur biphasique agité utilisant lhuile de silicone comme seconde phase. Initialement, Rhodococcus erythropolis T 902.1 a été sélectionné sur base de sa capacité à dégrader lisopropylbenzène (IPB), un composé choisi comme modèle représentatif de la famille du benzène. Deuxièmement, le transfert de masse de loxygène et de lIPB a été étudié en relation avec les conditions hydrodynamiques du réacteur et le type dhuile de silicone. Lutilisation dune proportion de 10 % dhuile de faible viscosité (10cSt) naffecte pas significativement le transfert de masse de loxygène. Cependant la grande solubilité de lIPB dans lhuile de silicone conduit à une forte augmentation du potentiel de transfert, spécialement pour les proportions en huile les plus élevées. Néanmoins, il ne semble pas utile de dépasser une proportion de 10 % car le KLaIPB et le KLaO2 diminuent drastiquement pour des proportions supérieures. Lexistence dune concentration optimale en élément biotique apparaît également. En effet, les concentrations optimales en biomasse (B) et extrait surfactant (ES) peuvent être évaluées à, respectivement 0,5 g/L et 0,7 g/L, elles assurent une valeur maximale du coefficient global de transfert de masse de loxygène (KLaO2). Plus spécifiquement, lES augmente laire interfaciale « a » en diminuant le diamètre des bulles tandis que la biomasse la diminue dès quune concentration de 1 g/L est atteinte. Au contraire, lES agit négativement sur le KL tandis que la biomasse laméliore globalement. En terme de performance, il est clairement montré que la taux de biodégradation de lIPB est davantage corrélé au débit gazeux de leffluent quà la concentration en polluant. Le réacteur biphasique a été suivi sur une période de 38 jours afin de caractériser son comportement à moyen terme pour différentes conditions opératoires. Lors dune phase dalimentation transitoire (10h/j), la capacité moyenne délimination est denviron 240 g/m3 pour une charge massique de 390 g/m3. Finalement, une approche originale a été développée en utilisant un bioréacteur de type scale-down pour reproduire les conditions hydrodynamiques rencontrées dans les réacteurs industriels. Il est clairement démontré que le polluant (IPB) affecte négativement lextrapolation en augmentant la vitesse de séparation de phase. Cependant cet impact négatif est largement compensé par la présence déléments biotiques qui stabilise fortement le système biphasique, rendant totalement envisageable lextrapolation à grande échelle. En conclusion, lutilisation dun réacteur biphasique eau-huile de silicone pour lélimination de concentrations élevées (~ 6g/m3) en polluants hydrophobes est adéquate. Le réacteur proposé présente de réelles opportunités pour le traitement biologique deffluents pollués par des composés hydrophobes. Son utilisation pourrait être envisagée lorsque loxydation thermique savère trop onéreuse ou lorsque les biofiltres classiques atteignent leurs limites ( >1 g/Nm3 et une charge volumique de 90m3/m3.h.)./Recently, a lot of research has been devoted to the study of two-phase partitioning bioreactors (TPPB) as new technology for xenobiotic degradation in gaseous effluents. These reactors involve the use of a second non-aqueous phase to improve the solubility and transfer of hydrophobic compounds. In this work, we have developed a stirred two-phase partitioning bioreactor using silicone oil as second phase. Initially, Rhodococcus erythropolis T 902.1 was selected on the basis of its capacity to metabolize isopropyl-benzene (IPB), used as representative of the benzene-containing compounds. Secondly, the mass transfer of both IPB and oxygen has been considered with relation to their influence on the hydrodynamics of the reactor and the type of silicone oil used. The addition of 10% low viscosity silicone oil (10 cSt) in the reactor does not significantly affect the oxygen transfer rate. The very high solubility of IPB in the silicone oil leads to an enhancement of the driving force term, especially when high proportion of silicone oil are used. However, it is not necessary to use a volume fraction higher than 10% since KLaIPB and KLaO2 decrease sharply at above such proportion. In addition, an optimal concentration appeared to exist for both biotic components, respectively 0,5 g/L and 0,7 g/L for biomass (B) and surfactant extract (SE) when the global mass transfer coefficient (KLa) of oxygen was measured in the TPPB. More specifically, SE improved the interfacial area a by decreasing the bubble diameter, while B reduced it at concentrations up to 1 g/L. In contrast, the SE concentration acted negatively on KL, while it was favoured by the B concentration. In term of performances, it was clearly shown that the biodegradation rate is more directly related to the inlet flow of IPB than to the concentration of IPB in the inlet gas. The TPPB was monitored for 38 days to characterise its behaviour under several operational conditions. During an intermittent loading phase (10 h/day), the average elimination capacity remained above 240 g/m3.h for an average IPB inlet load of 390 g/m3. h. Finaly, an original approach was developed using a scale-down bioreactor allowing to reproduce the hydrodynamics encountered under full scale TPPB. It was clearly shown that the IPB affects negatively the scaling-up of the process by increasing the speed of phase partitioning. However, this negative impact was strongly compensated by the presence of biotic compounds stabilizing the two phase system and rendering the scaling-up process feasible. In conclusion, the use of a water-silicone oil TPPB to remove a high inlet load of IPB was successful. The proposed reactor retains a high potential for the biological treatment of gas effluents polluted by hydrophobic aromatic compounds. The suggested process might be applied in the range of concentration and flow where thermal oxidation is too expensive (between 1 and 7 g/Nm3) or when the biofilters are usually limited, i.e. to treat a polluted effluent concentrated with > 1 g/Nm3 at a flow of 90m3/m3.h.

Finite-volume methods have been used for modeling of fluidflows involved in forced convection electrochemical coating androtating spray painting systems. Electrodeposition on a singlecircular cylinder under forced convection for Reynolds numbers10 and 200 was simulated. Comparisons with earlier numericaland theoretical results are presented and it is shown that theunsteady wake that appears for Reynolds numbers greater than 50affects the mass transfer from the surface of the cylinder onlyin an average sense. This result is compared with a heattransfer case, where unsteadiness is much more manifest. Theeffect of application of circulation movement around thecylinder surface was considered, showing that the use ofoptimal values for circulation can create a recirculation zonearound the cylinder and result in a remarkable improvement ofthe deposit uniformity. The magnetoelectrolysis researchdiscipline is presented with focus on magnetic fields uses onmass transfer processes. A classification of the governingdimensionless parameters that control the phenomena isproposed. Application of magnetoelectrolysis on electroplatingprocesses is done for the first time. It is found that the useof an alternating magnetically induced force around thecylinder can result in interesting improvement of quality andproductivity. Application of numerical methods is also studiedin another field of the surface finishing industry, thepainting atomizers. A critical situation of "reverse flow" isanalyzed. Different parameters of this phenomenon are studiedand suggestions for atomizers design are given and tested. <b>Keywords:</b>mass transfer, electrochemical coating, iontransport, forced convection, diffusion, magnetoelectrolysis,electrolyte, limiting current, numerical simulation,finite-volume methods, paint atomization, Coanda effect.

No description available.

The objective of this work has been to study equilibrium and non equilibrium situations during high pressure gas processing operations with emphasis on utilization of the high reservoir pressure. The well stream pressures of some of the condensate and gas fields in the North Sea are well above 200 bar. Currently the gas is expanded to a specified processing condition, typically 40-70 bar, before it is recompressed to the transportation conditions. It would be a considerable environmental and economic advantage to be able to process the natural gas at the well stream pressure. Knowledge of thermodynamic- and kinetic properties of natural gas systems at high pressures is needed to be able to design new high pressure process equipment. Nowadays, reactive absorption into a methyldiethanolamine (MDEA)solution in a packed bed is a frequently used method to perform acid gas treating. The carbon dioxide removal process on the Sleipner field in the North Sea uses an aqueous MDEA solution and the operation pressure is about 100 bar. The planed carbon dioxide removal process for the Snøhvit field in the Barents Sea is the use of an activated MDEA solution. The aim of this work has been to study high-pressure effects related to the removal of carbon dioxide from natural gas. Both modelling and experimental work on high-pressure non-equilibrium situations in gas processing operations have been done. Few experimental measurements of mass transfer in high pressure fluid systems have been published. In this work a wetted wall column that can operate at pressures up to 200 bar was designed and constructed. The wetted wall column is a pipe made of stainless steel where the liquid is distributed as a thin liquid film on the inner pipewall while the gas flows co- or concurrent in the centre of the pipe. The experiments can be carried out with a well-defined interphase area and with relatively simple fluid mechanics. In this way we are able to isolate the effects we want to study in a simple and effective way. Experiments where carbon dioxide was absorbed into water and MDEA solutions were performed at pressures up to 150 bar and at temperatures 25 and 40°C. Nitrogen was used as an inert gas in all experiments. A general non-equilibrium simulation program (NeqSim) has been developed. The simulation program was implemented in the object-oriented programming language Java. Effort was taken to find an optimal object-oriented design. Despite the increasing popularity of object-oriented programming languages such as Java and C++, few publications have discussed how to implement thermodynamic and fluid mechanic models. A design for implementation of thermodynamic, mass transfer and fluid mechanic calculations in an object-oriented framework is presented in this work. NeqSim is based on rigorous thermodynamic and fluid mechanic models. Parameter fitting routines are implemented in the simulation tool and thermodynamic-, mass transfer- and fluid mechanic models were fitted to public available experimental data. Two electrolyte equations of state were developed and implemented in the computer code. The electrolyte equations of state were used to model the thermodynamic properties of the fluid systems considered in this work (non-electrolyte, electrolyte and weak-electrolyte systems). The first electrolyte equation of state (electrolyte ScRK-EOS) was based on a model previously developed by Furst and Renon (1993). The molecular part of the equation was based on a cubic equation of state (Scwarzentruber et.al. (1989)’s modification of the Redlich-Kwong EOS) with the Huron-Vidal mixing rule. Three ionic terms were added to this equation – a short-range ionic term, a long-range ionic term (MSA) and a Born term. The thermodynamic model has the advantage that it reduces to a standard cubic equation of state if no ions are present in the solution, and that public available interaction parameters used in the Huron-Vidal mixing rule could be utilized. The originality of this electrolyte equation of state is the use of the Huron-Vidal mixing rule and the addition of a Born term. Compared to electrolyte models based on equations for the gibbs excess energy, the electrolyte equation of state has the advantage that the extrapolation to higher pressures and solubility calculations of supercritical components is less cumbersome. The electrolyte equation of state was able to correlate and predict equilibrium properties of CO2-MDEA-water solutions with a good precision. It was also able to correlate high pressure data of systems of methane-CO2-MDEA and water. The second thermodynamic model (electrolyte CPA-EOS) evaluated in this work is a model where the molecular interactions are modelled with the CPA (cubic plus association) equation of state (Kontogeorgios et.al., 1999) with a classical one-parameter Van der Walls mixing rule. This model has the advantage that few binary interaction parameters have to be used (even for non-ideal solutions), and that its extrapolation capability to higher pressures is expected to be good. In the CPA model the same ionic terms are used as in the electrolyte ScRK-EOS. A general non-equilibrium two-fluid model was implemented in the simulation program developed in this work. The heat- and mass-transfer calculations were done using an advanced multicomponent mass transfer model based on non-equilibrium thermodynamics. The mass transfer model is flexible and able to simulate many types of non-equilibrium processes we find in the petroleum industry. A model for reactive mass transfer using enhancement factors was implemented for the calculation of mass transfer of CO2 into amine solutions. The mass transfer model was fitted to the available mass transfer data found in the open literature. The simulation program was used to analyse and perform parameter fitting to the high pressure experimental data obtained during this work. The mathematical models used in NeqSim were capable of representing the experimental data of this work with a good precision. From the experimental and modelling work done, we could conclude that the mass transfer model regressed to pure low-pressure data also was able to represent the high-pressure mass transfer data with an acceptable precision. Thus the extrapolation capability of the model to high pressures was good. For a given partial pressure of CO2 in the natural gas, calculations show a decreased CO2 capturing capacity of aqueous MDEA solutions at increased natural gas system pressure. A reduction up to 40% (at 200 bar) compared to low pressure capacity is estimated. The pressure effects can be modelled correctly by using suitable thermodynamic models for the liquid and gas. In a practical situation, the partial pressure of CO2 in the natural gas will be proportional to the total pressure. In these situations, it is shown that the CO2 capturing capacity of the MDEA solution will be increased at rising total pressures up to 200 bar. However, the increased capacity is not as large as we would expect from the higher CO2 partial pressure in the gas. The reaction kinetics of CO2 with MDEA is shown to be relatively unaffected by the total pressure when nitrogen is used as inert gas. It is however important that the effects of thermodynamic and kinetic non- ideality in the gas and liquid phase are modelled in a consistent way. Using the simulation program NeqSim – some selected high-pressure non-equilibrium processes (e.g. absorption, pipe flow) have been studied. It is demonstrated that the model is capable of simulating equilibrium- and non-equilibrium processes important to the process- and petroleum industry.

Absorption space-conditioning systems are environmentally benign alternatives to vapor compression systems and have the capability of being driven by waste heat. However, a lack of practically feasible and economically viable compact heat and mass exchangers is a major limitation in the success of this technology. The viability of the absorption cycle depends upon the performance of the absorber, which experiences large heat and mass transfer resistances due to adverse temperature and concentration gradients during the phase change of the binary mixture working fluid, resulting in large overall component sizes. Understanding of the coupled heat and mass transfer during binary fluid mixture absorption at the microscales is critical for the miniaturization of these components, which will enable broad implementation of this technology. The proposed study aims to achieve this by investigating ammonia-water absorption for two distinct flow configurations: external falling films and internal convective flows. For the falling-film absorption case, ammonia-water solution flows around an array of small diameter coolant tubes while absorbing vapor. This absorber is installed in a test facility comprising all components of a single-effect absorption chiller to provide realistic operating conditions at the absorber. Local temperature, pressure, and flow measurements will be taken over a wide range of operating conditions and analyzed to develop a heat and mass transfer model for falling-film ammonia-water absorption. A microscale convective flow absorber will also be investigated. This absorber consists of an array of parallel, aligned alternating shims with integral microscale features, enclosed between cover plates. These microscale features facilitate flow of various fluid streams and the associated heat and mass transfer. The use of microchannels induces high heat and mass transfer rates without any active or passive surface enhancement. The microscale absorber for small-scale applications will be evaluated over a wide range of operating conditions on a single-effect absorption heat pump breadboard test facility. The study will conclude with a comparison of the two flow configurations for absorption, with recommendations for their application in future miniaturization efforts

The convective mass transfer coefficient is determined for evaporation in a horizontal rectangular duct, which forms the test section of the transient moisture transfer (TMT) facility. In the test facility, a short pan is situated in the lower panel of the duct where a hydrodynamically fully developed laminar or turbulent airflow passes over the surface of the water. The measured convective mass transfer coefficients have uncertainties that are typically less than ±10% and are presented for Reynolds numbers (ReD) between 560 and 8,100, Rayleigh numbers (RaD) between 6,100 and 82,500, inverse Graetz numbers (Gz) between 0.003 and 0.037, and operating conditions factors (H*) between -3.6 and -1.4. The measured convective mass transfer coefficients are found to increase as ReD, RaD, Gz and H* increase and these effects are included in the Sherwood number (ShD) correlations presented in this thesis, which summarize the experimental data.<p> An analogy between heat and mass transfer is developed to determine the convective heat transfer coefficients from the experimentally determined ShD correlations. The convective heat transfer coefficient is found to be a function of ShD and the ratio between heat and moisture transfer potentials (S*) between the surface of the water and the airflow in the experiment. The analogy is used in the development of a new method that converts a pure heat transfer NuD (i.e., heat transfer with no mass transfer) and a pure mass transfer ShD (i.e., mass transfer with no heat transfer) into NuD and ShD that are for simultaneous heat and mass transfer. The method is used to convert a pure heat transfer NuD from the literature into the NuD and ShD numbers measured in this thesis. The results of the new method agree within experimental uncertainty bounds, while the results of the traditional method do not, indicating that the new method is more applicable than the traditional analogy between heat and mass transfer during simultaneous heat and mass transfer.<p>A numerical model is developed that simulates convective heat and mass transfer for a vapor permeable Tyvek® membrane placed between an airflow and liquid water. The boundary conditions imposed on the surfaces of the membrane within the model are typical of the conditions that are present within the TMT facility. The convective heat and mass transfer coefficients measured in this thesis are applied in the model to determine the heat and moisture transfer through the membrane. The numerical results show that the membrane responds very quickly to a step change in temperature and relative humidity of the air stream. Since the transients occur over a short period of time (less than 1 minute), it is feasible to use a steady-state model to determine the heat and mass transfer rates through the material for HVAC applications.<p>The TMT facility is also used to measure the heat and moisture transfer through a vapor permeable Tyvek® membrane. The membrane is in contact with a water surface on its underside and air is passed over its top surface with convective boundary conditions. The experimental data are used to verify the numerically determined moisture transfer rate through the Tyvek® membrane. The numerical model is able to determine the mass transfer rates for a range of testing conditions within ±26% of the experimental data. The differences between the experiment and the model could be due to a slightly different mass transfer coefficient for flow over Tyvek® than for flow over a free water surface.

An External Loop Airlift Bioreactor with a small amount (99% porosity) of stainless steel mesh packing inserted in the riser section was used for bioremediation of a phenol polluted air stream. The packing enhanced VOC and oxygen mass transfer rates and provided a large surface area for cell immobilization. Using a pure strain of Pseudomonas putida, fed-batch and continuous runs at three different dilution rates were completed with phenol in the polluted air as the only source of growth substrate. 100% phenol removal was achieved at phenol loading rates up to 33120 mg/h.m3 using only one third of the column, superior to any previously reported biodegradation rates of phenol polluted air with 100% efficiency. A mathematical model has been developed and is shown to accurately predict the transient and steady state data.

The ultimate goal of this study is to examine the feasibility of extracting silicon from silica through electrolysis. The objective of the thesis was to evaluate the physico-chemical properties of a cryolite-lithium fluoride mixture as an electrolyte for the electrolysis process. A study of 86.2wt%Cryolite and13.8wt%Lithium fluoride melt with silica concentration varying from 0-4wt% and temperature range of 900-1000°C was done. Three properties were measured using two sets of experiments: 1) Dissolution Behaviour Determination, to obtain a) solubility limit, b) dissolution rate (mass transfer coefficient) and 2) density using Archimedes’ Principle. The study concluded that solubility and dissolution rate increases with temperature and the addition of LiF to cryolite decreases the solubility limit but increases the rate at which silica dissolves into the melt. With addition of silica, the apparent density of electrolyte first increases up to 2-3wt% and the drops.