In this thesis, novel multi-section laser diodes based on quantum-dot material are designed and investigated which exhibit a number of advantages such as low threshold current density; temperature-insensitivity and suppress carrier diffusion due to discrete nature of density of state of quantum-dots. The spectral versatility in the range of 1.1 µm – 1.3 µm wavelengths is demonstrated through novel mode-locking regimes such as dual-wavelength mode-locking, wavelength bistability and broad tunability. Moreover, broad pulse repetition rate tuning using an external cavity configuration is presented. A high peak power of 17.7 W was generated from the quantum-dot laser as a result of the tapered geometry of the gain section of the laser has led to successful application of such device for two-photon imaging. Dual-wavelength mode-locking is demonstrated via ground (?=1180 nm) and excited (?=1263 nm) spectral bands with optical pulses from both states simultaneously in the 5-layer quantum-dot two-section diode laser. The widest spectral separation of 83 nm between the modes was achieved in a dual-wavelength mode-locked non-vibronic laser. Power and wavelength bistability are achieved in a mode-locked multi-section laser which active region incorporates non-identical QD layers grown by molecular beam epitaxy. As a result the wavelength can be electronically controlled between 1245 nm and 1290 nm by applying different voltages to the saturable absorber. Mode-locked or continuous-wave regimes are observed for both wavelengths over a 260 mA – 330 mA current ranges with average power up to 28 mW and 31 mW, respectively. In mode-locked regime, a repetition rate of 10 GHz of optical pulses as short as 4 ps is observed. Noticeable hysteresis of average power for different bias conditions is also demonstrated. The wavelength and power bistability in QD lasers are potentially suitable for flip-flop memory application. In addition, a unique mode-locked regime at expense of the reverse bias with 50 nm wavelength tuning range from 1245 nm to 1290 nm is also presented. Broad repetition rate tunability is shown from quantum-dot external cavity mode-locked 1.27 µm laser. The repetition rate from record low of 191 MHz to 1 GHz from fundamental mode-locking was achieved. Harmonic mode-locking allows further to increase tuning up to 6.8 GHz (34th-order harmonic) from 200 MHz fundamental mode-locking. High peak power of 1.5 W can be generated directly from two-section 4 mm long laser with bent waveguide at angle of 7° at 1.14 GHz repetition rate without the use of any pulse compression and optical amplifier. Stable mode-locking with an average power up to 60 mW, corresponding to 25 pJ pulse energy is also obtained at a repetition frequency of 2.4 GHz. The minimum time-bandwidth product of 1.01 is obtained with the pulse duration of 8.4 ps. Novel tapered quantum-dot lasers with a gain-guided geometry operating in a passively mode-locked regime have been investigated, using structures that incorporated either 5 or 10 quantum dot layers. The peak power of 3.6 W is achieved with pulse duration of 3.2 ps. Furthermore, the record peak power of 17.7 W and transform limited pulses of 672 fs were achieved with optimized structure. The generation of picosecond pulses with high average power of up to 209 mW was demonstrated, corresponding to 14.2 pJ pulse energy. The improved optical parameters of the tapered laser enable to achieve nonlinear images of fluorescent beads. Thus it is for the first time that QD based compact monolithic device enables to image biological samples using two-photon microscopy imaging technique.

Thesis (doctoral)--Universität, Paderborn, 2000.

Thesis (Ph.D.) - University of St Andrews, December 2007.

Thesis (M.S. in Electrical Engineering)--Naval Postgraduate School, June 2005. / Thesis Advisor(s): Phillip E. Pace. Includes bibliographical references (p. 55). Also available online.

Thesis (Ph. D.)--University of Washington, 2005. / Vita. Includes bibliographical references (leaves 94-98).

Mode-locked fiber lasers have attracted significant scientific and commercial interest since they offer a compact and highly stable platform with straightforward operation for exploiting ultrafast and nonlinear phenomena. They have enabled a vast range of applications that span from distinct disciplines such as medical diagnostics, molecular spectroscopy, and high-power precise mechanical cutting, to optical metrology. Various gain media have been utilized to achieve laser emission at different wavelengths. We have developed unique thulium/holmium (Tm/Ho) doped mode-locked fiber laser systems to address the needs of low-noise ultrafast optical sources in the wavelength vicinity of 2 μm at higher repetition rates. Since the 2 μm wavelength regime has recently attracted more attention with the emergence of thulium gain fibers, the rich underlying cavity dynamics, novel pulse operation regimes and nonlinear phenomena in compact fiber configurations have not been fully explored yet. In this thesis, research is conducted on novel Tm fiber laser cavity configurations and on the formation of unique, polarization-based pulsing regimes. Particularly, this research is focused on the exploration of novel ultrafast and nonlinear phenomena, and the development of optical sources emitting unprecedented ultrafast pulse trains beyond conventional equal-intensity distribution using Tm/Ho doped gain media. The research presented features four main results: 1) development of a high repetition rate and low-noise Tm/Ho doped mode-locked fiber laser platform as an attractive optical source for a wide variety of applications 2) investigation of a novel mode-locked state in which the ultrafast pulse train is composed of co-generated, consecutive, equal intensity and orthogonally polarized pulses in order to achieve dual RF comb generation for dual-comb spectroscopy applications, 3) exploration of controllable ultrafast waveform generation utilizing vector soliton and harmonic mode-locking mechanisms for optical telecommunication applications, and 4) demonstration of unique transitional mode-locked states showing exceptional features such as powerful irregular bursts of ultrafast pulses and rogue wave behavior without damaging the laser elements. The aim of these projects has been to explore the novel optical properties of Tm/Ho co-doped fiber lasers in order to achieve advanced functionalities in commonly practiced applications such as telecommunication, metrology and spectroscopic applications. / 2019-10-22T00:00:00Z

This master thesis presents an experimental design of a laser gyroscope based on a stabilized fiber optical parametric oscillator frequency comb and the results of testing of the proposed design. Before going into the experimental details, a background for different types of gyroscopes is discussed. This new laser gyroscope design is made up of only polarization maintaining (PM) fiber and PM fiber components. By using only fiber and fiber components, we were able to minimize size, weight, and alignment issues that are typical in bulk optical designs for OPO's and gyroscopes. The fiber-based OPO produces counter propagating ultrafast pulses that overlap only twice in the cavity, resulting in a beatnote signal when combined outside of the laser cavity. A mode-locked laser is used as a pump source so the lock-in effect (or deadband region) is avoided for the experiment. The drift of this beatnote signal represents the rotation sensitivity of the experimental setup. Issues seen in past iterations, such as stability of mode-locked pump source and beatnote drift overtime due to environmental variables, have been reduced in this experiment. This has been done by comprising the entire pump source of PM components, and by placing the entire setup in an insulating box to minimize acoustic and temperature fluctuations. By creating a frequency comb and locking the laser gyroscope to an optical clock, this experiment can be used for very precise rotation sensing in comparison to other gyro designs currently available.

Thesis. 1976. Sc.D.--Massachusetts Institute of Technology. Dept. of Electrical Engineering and Computer Science. / Microfiche copy available in Archives and Engineering. / Vita. / Includes bibliographical references. / Sc.D.

The topic of this dissertation is the development of low repetition rate and low noise semiconductor-based laser sources with a focus on linearly chirped pulse laser sources. In the past decade chirped optical pulses have found a plethora of applications such as photonic analogto-digital conversion, optical coherence tomography, laser ranging, etc. This dissertation analyzes the aforementioned applications of linearly chirped pulses and their technical requirements, as well as the performance of previously demonstrated chirped pulse laser sources. Moreover, the focus is shifted to a specific application of the linearly chirped pulses, timestretched photonic analog-to-digital conversion (TS ADC). The challenges of surpassing the speeds of current electronic converters are discussed, while the need for low noise linearly chirped pulse lasers becomes apparent for the realization of TS ADC. The experimental research addresses the topic of low noise chirped pulse generation in three distinct ways. First, a chirped pulse (Theta) laser with an intra-cavity Fabry-Pérot etalon and a long-term referencing mechanism is developed that results in the reduction of the pulse-topulse energy noise. Noise suppression of > 15 times is demonstrated. Moreover, an optical frequency comb with spacing equal to the repetition rate (≈100 MHz) is generated using the etalon, resulting in the first reported demonstration of a system operating in the sub-GHz regime based on semiconductor gain. The path for the development of the Theta laser was laid by the precise characterization of the etalon used in this laser cavity design. A narrow linewidth laser is used in conjunction with an acousto-optic modulator externally swept for measuring the etalon's iv free spectral range with a sub-Hz precision, or 10 parts per billion. Furthermore, the measurement of the etalon long-term drift and birefringence lead to the development of a modified intra-cavity Hänsch-Couillaud locking mechanism for the Theta laser. Moreover, an external feed-forward system was demonstrated that aimed at increasing the temporal/spectral uniformity of the optical pulses. A complete characterization of the system is demonstrated. On a different series of experiments, the pulses emitted by an ultra-low noise but high repetition rate mode-locked laser were demultiplexed resulting in a low repetition rate pulse train. Experimental investigation of the noise properties of the laser proved that they are preserved during the demultiplexing process. The noise of the electrical gate used in this experiment is also investigated which led into the development of a more profound understanding of the electrical noise of periodical pulses and a mechanism of measuring their noise. The appendices in this dissertation provide additional material used for the realization of the main research focus of the dissertation. Measurements of the group delay of the etalon used in the Theta laser are presented in order to demonstrate the limiting factors for the development of this cavity design. The description of a balancing routine is presented, that was used for expanding the dynamic range of intra-cavity active variable delay. At last, the appendix presents the calculations regarding the contribution of various parameters in the limitations of analog-todigital conversion.

Recently optical frequency combs and low noise RF tones are drawing increased attention due to applications in spectroscopy, metrology, arbitrary waveform generation, optical signal processing etc. This thesis focuses on the generation of low noise RF tones and stabilized optical frequency combs. The optical frequency combs are generated by a semiconductor based external cavity mode-locked laser with a high finesse intracavity etalon. In order to get the lowest noise and broadest bandwidth from the mode-locked laser, it is critical to know the free spectral range (FSR) of the etalon precisely. First the etalon FSR is measured by using the modified Pound-Drever-Hall (PDH) based method and obtained a resolution of 1 part in 106 , which is 2 order of magnitude better than the standard PDH based method. After optimizing the cavity length, RF driving frequency and PDH cavity locking point, the mode-locked laser had an integrated timing jitter of 3 fs (1 Hz- 100 MHz) which is, to the best of our knowledge, the lowest jitter ever reported from a semiconductor based multigigahertz comb source. The modelocked laser produces ~ 100 comb lines with 10 GHz spacing, a linewidth of ~500 Hz and 75 dB optical signal-to-noise ratio. The same system can also be driven as a regeneratively modelocked laser with greatly improved noise performance. Another way of generating a low noise RF tone is using an opto-electronic oscillator which uses an optical cavity as a high Q element. Due to the harmonic nature of OEOs, a mode selection element is necessary. Standard OEOs use an RF filter having drawbacks such as broad pass band, high loss, and high thermal noise. In our work, a novel optoelectronic scheme which uses an optical filter (Fabry-Perot etalon) as the mode filter instead of an RF filter is demonstrated. This method has the advantage of having ultra-narrow filtering bandwidths ( ~ 10 iv kHz for a 10 GHz FSR and 106 finesse) and an extremely low noise RF signal. Experimental demonstration of the proposed method resulted in a 5-10 dB decrease of the OEO noise compared to the conventional OEO setup. Also, by modifying the etalon-based OEO, and using single side band modulation, an optically tunable optoelectronic oscillator is achieved with 10-20 dB lower noise than dual side band modulation. Noise properties of the OEO as a function of optical frequency detuning is also analyzed theoretically and the results are in agreement with experimental results. The thesis concludes with comments on future work and directions.