Polymer electrolyte fuel cells (PEFCs) have emerged as a promising renewable emission-free technology to solve the worldwide increasing demand for clean and efficient energy conversion. Despite large efforts in academia and automotive industry, the commercialization of PEFC vehicles still remains a great challenge. Critical issues are high material costs, insufficient catalytic activity as well as longterm durability. Especially due to the sluggish kinetics of the oxygen reduction reaction (ORR), high Pt loadings on the cathode are still necessary which leads to elevated costs. Alloys of Pt with other less precious metals (Co, Ni, Fe, Cu, etc.) show improved ORR activities compared to pure Pt catalysts. However, state-of-the-art carbon-supported catalysts suffer from severe Pt and carbon corrosion during the standard operation of PEFCs, affecting their reliability and long-term efficiency. Multimetallic aerogels constitute excellent candidates to overcome these issues. Due to their large open pores and high inner surface areas combined with electrical conductivity, they are ideal for applications in electrocatalysis. In addition, they can be employed without any catalyst support. Therefore, the fabrication of bimetallic Pt-M (M=Ni, Cu, Co, Fe) aerogels for applications in fuel cell catalysis was the focus of this thesis. Based on a previously published synthesis for Pt–Pd aerogels, a facile one-step procedure at ambient conditions in aqueous solution was developed. Bimetallic aerogels with nanochain diameters of as small as 4 nm and Brunauer-Emmett-Teller (BET) surface areas of up to 60 m2/g could be obtained. Extensive structure analysis of Pt–Ni and Pt–Cu aerogels by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), scanning transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy (STEM-EDX) and electrochemical techniques showed that both metals were predominantly present in their metallic state and formed homogeneous alloys. However, metal (hydr)oxide byproducts were observed in aerogels with higher contents of non-precious metal (>25 %). Moreover, electronic and geometric structures were similar to those of carbon-supported Pt alloy catalysts. As a result, ORR activites were comparable, too. A threefold improvement in surface-specific activity over Pt/C catalysts was achieved. The mass-specific activites met or exceeded the U.S. Department of Energy (DOE) target for automotive PEFC applications. Furthermore, a direct correlation between non-precious metal content in the alloy and ORR activity was discovered. Aerogels with nonprecious metal contents >25% turned out to be susceptible to dealloying in acid leaching experiments, but there was no indication for the formation of extended surface structures like Pt-skeletons. A Pt3Ni aerogel was successfully employed as the cathode catalyst layer in a differential fuel cell (1 cm2), which is a crucial step towards technical application. This was the first time an unsupported metallic aerogel was implemented in a PEFC. Accelerated stress tests that are usually applied to investigate the support stability of fuel cell catalysts revealed the excellent stability of Pt3Ni alloyed aerogels. In summary, the Pt alloy aerogels prepared in the context of this work have proven to be highly active oxygen reduction catalysts with remarkable stability.

No description available.

This thesis describes the study of a series of multimetallic supramolecules containing varied metals and ligands, synthesized by a building block method and characterized by mass spectrometry, electronic absorption spectroscopy, and electrochemistry. Incorporating different functional units into complex systems allowed these multimetallic supramolecules to perform various light activated tasks including DNA cleavage and hydrogen generation from water. The complex [({(bpy)₂Os(dpp)}₂Ru)₂(dpq)](PF₆)₁₂ and [{(bpy)₂M(dpp)}₂Ru(BL)PtCl₂](PF₆)₆ were synthesized (M = Os^II or Ru^II; BL = dpp or dpq; bpy = 2,2^'-bipyridine, dpp = 2,3-bis(2-pyridyl)pyrazine, dpq = 2,3-bis(2-pyridyl)quinoxaline). The building blocks displayed varied electrochemical properties upon complexation. The bridging ligands dpp and dpq display their reduction potentials shifted to less negative values when they changed from monochelating to bischelating. The electronic absorption spectra of the multimetallic systems displayed transitions of each contributing chromophore, with overlapping metal to ligand charge transfer (MLCT) transitions in visible region of spectrum. Spectroelectrochemistry revealed the nature of MLCTs and helped to identify fingerprint features of complex supramolecules. Photophysical measurements include emission spectroscopy with quantum yield measurements and emission lifetime measurements. Photophysical data provided detailed information to aid in developing an understanding of excited state properties of these complexes. Supported by the electrochemical data and spectroelectrochemistry, the hexametallic complex was suggested to have a HOMO localizing in the peripheral Os and a LUMO localizing in the central dpq, separating by a Ru energy barrier. This research systematically investigated photophysical properties of some building blocks and the mixed-metal, mixed-ligand supramolecules constructed by a variety of building blocks coupling light absorbing subunits to a reactive Pt metal center. Preliminary studies suggested [{(bpy)₂Ru(dpp)}₂Ru(dpq)PtCl₂](PF₆)₆ was a photocatalyst for H2 production from water in the presence of a sacrificial electron donor. The complex [{(bpy)₂Ru(dpp)}₂Ru(dpq)PtCl₂](PF₆)₆ had been studied for its catalytic ability in generating hydrogen and was found to have 34 product turnovers after 3 h photolysis. Photolysis and gel electrophoresis revealed that the tetrametallic complexes were able to bind to and then photocleave DNA through an oxygen mediated mechanism. The independence of ionic strength variation when [{(bpy)₂Ru(dpp)}₂Ru(dpp)PtCl₂](PF₆)₆ interacted with DNA, suggested the covalent interaction nature of the complex. These results suggest future work on understanding the excited state properties of supramolecular complexes is suggested. The designs of future photocatalysts for hydrogen production from water and anticancer photodynamic therapy drugs are also proposed. / Ph. D.

L’objet de ces travaux de thèse est d’étudier la synthèse de polybutadiène au moyen de systèmes d’amorçage multi-métalliques. L’utilisation d’alcoolates de potassium en association avec des dérivés d’alkyllithium a été étudiée afin d’obtenir du polybutadiène de façon contrôlée avec 50% d’unités vinyliques en milieu apolaire. Dans un second temps, ces travaux démontrent que des systèmes d’amorçage sans lithium permettent la synthèse de polybutadiène par voie anionique. Lorsque le dialkylmagnesium est associé à un alcoolate de potassium, il permet l’obtention de polybutadiène avec 50% d’unités vinyliques, alors que le système dialkylmagnesium / alcoolate de baryum permet la synthèse de polybutadiène à fort taux de 1,4-trans (65%). / The goal of this research work is to find original ways to obtained polybutadiene with defined microstructure by developing multimetallic initiation systems. The aim of the first experimental chapter was to obtain polybutadiene with a 50% vinyl content in a controlled way in apolar media. This objective was achieved by using a bimetallic system based on potassium alkoxide and alkyllithium. The goal of the last experimental chapter was to prospect multimetallic initiation systems allowing obtention of polybutadiene without using lithium derivatives. The use of dialkylmagnesium in association with potassium alkoxide was found relevant to produce polybutadiene with a 50% vinyl content, while the association of dialkylmagnesium and barium alkoxide allows the synthesis of polybutadiene with a high 1,4-trans content (up to 65%).

New challenges in nanotechnology arise in the assembly of nanoobjects into three-dimensional superstructures, which may carry synergetic properties and open up new application fields. Within this new class of materials nanostructured, porous functional metals are of great interest since they combine high surface area, gas permeability, electrical conductivity, plasmonic behavior and size-enhanced catalytic reactivity. Even though a large variety of preparation pathways for the fabrication of porous noble metals has already been established, several limitations are still to be addressed by research developments. The new and versatile approach that is presented in this work makes use of a templatefree self-assembly process for the fabrication of highly porous, metallic nanostructures. Thereby, nanochains are formed by the controlled coalescence of noble metal NPs in aqueous media and their interconnection and interpenetration leads to the formation of a self-supported network with macroscopic dimensions. Subsequently, the supercritical drying technique is used to remove the solvent from the pores of the network without causing a collapse of the fragile structure. The resulting highly porous, low-weighted, three-dimensional nanostructured solids are named aerogels. The exceptional properties of these materials originate from the conjunction of the unique properties of nanomaterials magnified by macroscale assembly. Moreover, the combination of different metals may lead to synergetic effects regarding for example their catalytic activity. Therefore, the synthesis of multimetallic gels and the characterization of their structural peculiarities are in the focus of the investigations. In the case of the developed preparation pathways the gelation process starts from preformed, stable colloidal solutions of citrate capped, spherical noble metal (Au, Ag, Pt, Pd) NPs. In order to face various requirements several methods for the initiation of the controlled destabilization and coalescence of the nanosized building blocks were developed and synthesis conditions were optimized, respectively. Multimetallic structures with tunable composition are obtained by mixing different kinds of monometallic NP solutions and performing a joint gel formation. The characterization of the resulting materials by means of electron microscopy reveals the formation of a highly porous network of branched nanochains that provide a polycrystalline nature and diameters in the size range of the initial NPs. Furthermore, synthesis conditions for the spontaneous gel formation of glucose stabilized Au and Pd NPs were investigated. In order to gain a detailed knowledge of the structural properties of bimetallic aerogel structures a versatile set of characterization techniques was applied. A broad pore size distribution dominated by meso- and macropores and remarkably high inner surface areas were concluded from the N2 physisorption isotherms and density measurements. As investigated, a specific thermal treatment could be used to tune the ligament size of Au-Ag aerogels, whereas Au-Pd and Pt-Pd structures provide thermal stability under mild conditions. Further investigations aimed to the enlightenment of the elemental distribution and phase composition within the nanochains of multimetallic gel structures. The different approaches provide complementary and consistent results. Phase analyses based on XRD measurements revealed separated phases of each metal in the case of Ag-Pd and Au-Pd aerogels. They further proved the possibility of temperature induced phase modifications that lead to complete alloying of Au and Pd. In addition, separated domains of Pt and Pd were established from the EXAFS analysis of the corresponding aerogel. STEM EDX high resolution elemental mappings confirmed the separated domains of different metals in the case of Au-Pd and Pt-Pd aerogels. Moreover, a complete interdiffusion and alloy formation of Au and Ag within the corresponding aerogel structure is suggested from STEM EDX results. Finally, the presented investigations further promote the field of metallic aerogels by addressing the challenging issue of processability and device fabrication. Hybrid materials with organic polymers as well as various kinds of coatings on glass substrates and glassy carbon electrodes were prepared whereas the network structure was preserved throughout all processing steps. Moreover, it was illustrated that the NP-based aerogels carry metallic properties as expressed by their low Seebeck coefficients and high electrical conductivities.

Polymer electrolyte fuel cells (PEFCs) have emerged as a promising renewable emission-free technology to solve the worldwide increasing demand for clean and efficient energy conversion. Despite large efforts in academia and automotive industry, the commercialization of PEFC vehicles still remains a great challenge. Critical issues are high material costs, insufficient catalytic activity as well as longterm durability. Especially due to the sluggish kinetics of the oxygen reduction reaction (ORR), high Pt loadings on the cathode are still necessary which leads to elevated costs. Alloys of Pt with other less precious metals (Co, Ni, Fe, Cu, etc.) show improved ORR activities compared to pure Pt catalysts. However, state-of-the-art carbon-supported catalysts suffer from severe Pt and carbon corrosion during the standard operation of PEFCs, affecting their reliability and long-term efficiency. Multimetallic aerogels constitute excellent candidates to overcome these issues. Due to their large open pores and high inner surface areas combined with electrical conductivity, they are ideal for applications in electrocatalysis. In addition, they can be employed without any catalyst support. Therefore, the fabrication of bimetallic Pt-M (M=Ni, Cu, Co, Fe) aerogels for applications in fuel cell catalysis was the focus of this thesis. Based on a previously published synthesis for Pt–Pd aerogels, a facile one-step procedure at ambient conditions in aqueous solution was developed. Bimetallic aerogels with nanochain diameters of as small as 4 nm and Brunauer-Emmett-Teller (BET) surface areas of up to 60 m2/g could be obtained. Extensive structure analysis of Pt–Ni and Pt–Cu aerogels by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), scanning transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy (STEM-EDX) and electrochemical techniques showed that both metals were predominantly present in their metallic state and formed homogeneous alloys. However, metal (hydr)oxide byproducts were observed in aerogels with higher contents of non-precious metal (>25 %). Moreover, electronic and geometric structures were similar to those of carbon-supported Pt alloy catalysts. As a result, ORR activites were comparable, too. A threefold improvement in surface-specific activity over Pt/C catalysts was achieved. The mass-specific activites met or exceeded the U.S. Department of Energy (DOE) target for automotive PEFC applications. Furthermore, a direct correlation between non-precious metal content in the alloy and ORR activity was discovered. Aerogels with nonprecious metal contents >25% turned out to be susceptible to dealloying in acid leaching experiments, but there was no indication for the formation of extended surface structures like Pt-skeletons. A Pt3Ni aerogel was successfully employed as the cathode catalyst layer in a differential fuel cell (1 cm2), which is a crucial step towards technical application. This was the first time an unsupported metallic aerogel was implemented in a PEFC. Accelerated stress tests that are usually applied to investigate the support stability of fuel cell catalysts revealed the excellent stability of Pt3Ni alloyed aerogels. In summary, the Pt alloy aerogels prepared in the context of this work have proven to be highly active oxygen reduction catalysts with remarkable stability.

The major directions of this dissertation involve (1) the syntheses and characterization of molecular polygons incorporating sp1hybridized carbon linkers and L2Pt corners (L2 = cis-1,3-diphosphine), (2) the development of protected carbon chain complexes featuring fluorous phosphine ligands and (3) click reactions of metal terminal polyynyl complexes and further metallations of the resulting triazole rings. A brief overview is provided in Chapter I. Chapter II details the syntheses of molecular squares containing bidendate diphosphine ligands of the formula R2C(CH2PPh2)2 where R = Me, Et, n-Bu, n-Dec, Bn, and p-tolCH2 (general designation dppp*), in which the R2 groups are intended to circumvent the solubility issues encountered by others. Their syntheses involve double substitutions of the dimesylate compounds R2C(CH2OMs)2 using KPPh2. Building blocks of the formulae (dppp*)PtCl2 and (dppp*)Pt((C≡C)2H)2 are synthesized and characterized, including one crystal structure of the latter. The target complexes are accessed by reactions of (dppp*)PtCl2 with (dppp*)Pt((C≡C)2H)2 under Sonogashira type conditions. Six new squares of the formula [(R2C(CH2PPh2)2)Pt(C≡C)2]4 are characterized including two crystal structures. Further topics include approaches to higher homologues and cyclocarbon synthesis. Chapter III focuses on carbon chain complexes bearing fluorous phosphine ligands of the formula P((CH2)mRfn)3 (Rfn = (CF2)n-1CF3; m/n = 2/8, 3/8, and 3/10). Precursors of the formula trans-(C6F5)((Rfn(CH2)m)3P)2PtCl are synthesized and characterized, including one crystal structure, which reveals phase separation of the fluorous and non-fluorous domains. Reactions with butadiyne give trans-(C6F5)((Rfn(CH2)m)3P)2Pt(C≡C)2H. Oxidative homocouplings afford the target complexes trans,trans-(C6F5)((Rfn(CH2)m)3P)2Pt(C≡C)4(C6F5)(P((CH2)mRfn)3)2Pt. Cyclic voltammetry indicates irreversible oxidations of the title compounds, in contrast to partially reversible oxidations of non-fluorous analogues. Chapter IV focuses on multimetallic complexes achieved by click reactions in metal coordination spheres. The copper catalyzed click reaction between trans-(C6F5)(p-tol3P)2Pt(C≡C)2H (1) and (η5-C5H4N3)Re(CO)3 affords the bimetallic 1,2,3-triazole trans-C6F5)(p1tol3P)2PtC≡CC=CHN((η51C5H4)Re(CO)3)N=N. Further reactions with Re(CO)5OTf and Re(CO)5Br give trimetallated adducts, which represent the first species of this type. An alternative route to a trimetallic complex involves the twofold cycloaddition of the diazide (η5-C5H4N3)2Fe and 1, giving (η5-C5H4NN=N-C(trans-(C≡C)Pt(Pp-tol3)2(C6F5)=CH)2Fe. The crystal structures of the di and trimetallic complexes are compared, but attempts to achieve a fourth metallation involving the =CH groups are unsuccessful. However, when the triazolium salt [trans-(C6F5)(p-tol3P)2PtC≡CC=CHN(CH2C6H5)N=N(Me)]+ I– is treated with Ag2O and [Rh(COD)Cl]2, a =CRh adduct is obtained. The success of =CH metallation is correlated to the 1H NMR chemical shift, indicative of an electronic effect.

New challenges in nanotechnology arise in the assembly of nanoobjects into three-dimensional superstructures, which may carry synergetic properties and open up new application fields. Within this new class of materials nanostructured, porous functional metals are of great interest since they combine high surface area, gas permeability, electrical conductivity, plasmonic behavior and size-enhanced catalytic reactivity. Even though a large variety of preparation pathways for the fabrication of porous noble metals has already been established, several limitations are still to be addressed by research developments. The new and versatile approach that is presented in this work makes use of a templatefree self-assembly process for the fabrication of highly porous, metallic nanostructures. Thereby, nanochains are formed by the controlled coalescence of noble metal NPs in aqueous media and their interconnection and interpenetration leads to the formation of a self-supported network with macroscopic dimensions. Subsequently, the supercritical drying technique is used to remove the solvent from the pores of the network without causing a collapse of the fragile structure. The resulting highly porous, low-weighted, three-dimensional nanostructured solids are named aerogels. The exceptional properties of these materials originate from the conjunction of the unique properties of nanomaterials magnified by macroscale assembly. Moreover, the combination of different metals may lead to synergetic effects regarding for example their catalytic activity. Therefore, the synthesis of multimetallic gels and the characterization of their structural peculiarities are in the focus of the investigations. In the case of the developed preparation pathways the gelation process starts from preformed, stable colloidal solutions of citrate capped, spherical noble metal (Au, Ag, Pt, Pd) NPs. In order to face various requirements several methods for the initiation of the controlled destabilization and coalescence of the nanosized building blocks were developed and synthesis conditions were optimized, respectively. Multimetallic structures with tunable composition are obtained by mixing different kinds of monometallic NP solutions and performing a joint gel formation. The characterization of the resulting materials by means of electron microscopy reveals the formation of a highly porous network of branched nanochains that provide a polycrystalline nature and diameters in the size range of the initial NPs. Furthermore, synthesis conditions for the spontaneous gel formation of glucose stabilized Au and Pd NPs were investigated. In order to gain a detailed knowledge of the structural properties of bimetallic aerogel structures a versatile set of characterization techniques was applied. A broad pore size distribution dominated by meso- and macropores and remarkably high inner surface areas were concluded from the N2 physisorption isotherms and density measurements. As investigated, a specific thermal treatment could be used to tune the ligament size of Au-Ag aerogels, whereas Au-Pd and Pt-Pd structures provide thermal stability under mild conditions. Further investigations aimed to the enlightenment of the elemental distribution and phase composition within the nanochains of multimetallic gel structures. The different approaches provide complementary and consistent results. Phase analyses based on XRD measurements revealed separated phases of each metal in the case of Ag-Pd and Au-Pd aerogels. They further proved the possibility of temperature induced phase modifications that lead to complete alloying of Au and Pd. In addition, separated domains of Pt and Pd were established from the EXAFS analysis of the corresponding aerogel. STEM EDX high resolution elemental mappings confirmed the separated domains of different metals in the case of Au-Pd and Pt-Pd aerogels. Moreover, a complete interdiffusion and alloy formation of Au and Ag within the corresponding aerogel structure is suggested from STEM EDX results. Finally, the presented investigations further promote the field of metallic aerogels by addressing the challenging issue of processability and device fabrication. Hybrid materials with organic polymers as well as various kinds of coatings on glass substrates and glassy carbon electrodes were prepared whereas the network structure was preserved throughout all processing steps. Moreover, it was illustrated that the NP-based aerogels carry metallic properties as expressed by their low Seebeck coefficients and high electrical conductivities.

In dieser Arbeit werden kalt-abgeschiedene Mehrkomponentenschichtelektroden hin-sichtlich ihrer elektrokatalytischen Eigenschaften untersucht. Die Mehrkomponenten-schichten aus Gold, Nickel und ggf. Antimon werden auf einem Kohlenstoffträgermaterial abgeschieden. Dabei handelt es sich um Metallkomponenten, die sich unter ther-modynamischen Bedingungen nicht mischen. Unter UHV-Bedingungen wird ein hochdispergierter bzw. amorpher Zustand erzwungen. Die frisch hergestellte Mehrkomponentenschicht ist elektrochemisch inert. Zyklovoltammetrische Untersuchungen führen zu dem Schluß, daß sich die Oberflächenschicht im elektrochemischen Experiment verändert. Die Elektrooxidation der Alkohole Methanol, Ethanol und Ethylenglykol in KOH-Lösung tritt erst nach einer Aktivierungsphase auf. Die elektrokatalytischen Eigenschaften der reinen Metalle treten zutage. Mittels der in situ Infrarotspektroskopie werden Formiat, Acetat und Glykolat als Oxidationsprodukte der obengenannten Alkohole identifiziert. Oberflächen-Ramanmessungen werden unter der Fragestellung durchgeführt, ob die kalt-abgeschiedenen Schichten einen Oberflächenverstärkungseffekt (SERS-Effekt) zeigen: Es werden Ramanmessungen von Pyridin als Sondenmolekül in KOH-Lösung an Mehrkomponentenschichtelektroden und an massiven Mehrkomponentenelektroden durchgeführt. / The electrooxidation of methanol, ethanol and ethylene glycol at cold deposited trimetallic thin layers of gold, nickel and antimony on glassy carbon in contact with an alkaline electrolyte solution was studied with cyclic voltammetry and in situ infrared reflection absorption spectroscopy. A new procedure of spectra acquisition resulting in an improved suppression of spurious bands caused by volatile components in the sample chamber of the infrared spectrometer was employed. Formate, acetate and glycolate are detected as oxidation products. The thin layer electrodes are also investigated with Raman spectroscopy (surface enhanced Raman spectroscopy), whereby pyridine is used as probe molecule.

In dieser Arbeit werden kalt-abgeschiedene Mehrkomponentenschichtelektroden hin-sichtlich ihrer elektrokatalytischen Eigenschaften untersucht. Die Mehrkomponenten-schichten aus Gold, Nickel und ggf. Antimon werden auf einem Kohlenstoffträgermaterial abgeschieden. Dabei handelt es sich um Metallkomponenten, die sich unter ther-modynamischen Bedingungen nicht mischen. Unter UHV-Bedingungen wird ein hochdispergierter bzw. amorpher Zustand erzwungen. Die frisch hergestellte Mehrkomponentenschicht ist elektrochemisch inert. Zyklovoltammetrische Untersuchungen führen zu dem Schluß, daß sich die Oberflächenschicht im elektrochemischen Experiment verändert. Die Elektrooxidation der Alkohole Methanol, Ethanol und Ethylenglykol in KOH-Lösung tritt erst nach einer Aktivierungsphase auf. Die elektrokatalytischen Eigenschaften der reinen Metalle treten zutage. Mittels der in situ Infrarotspektroskopie werden Formiat, Acetat und Glykolat als Oxidationsprodukte der obengenannten Alkohole identifiziert. Oberflächen-Ramanmessungen werden unter der Fragestellung durchgeführt, ob die kalt-abgeschiedenen Schichten einen Oberflächenverstärkungseffekt (SERS-Effekt) zeigen: Es werden Ramanmessungen von Pyridin als Sondenmolekül in KOH-Lösung an Mehrkomponentenschichtelektroden und an massiven Mehrkomponentenelektroden durchgeführt. / The electrooxidation of methanol, ethanol and ethylene glycol at cold deposited trimetallic thin layers of gold, nickel and antimony on glassy carbon in contact with an alkaline electrolyte solution was studied with cyclic voltammetry and in situ infrared reflection absorption spectroscopy. A new procedure of spectra acquisition resulting in an improved suppression of spurious bands caused by volatile components in the sample chamber of the infrared spectrometer was employed. Formate, acetate and glycolate are detected as oxidation products. The thin layer electrodes are also investigated with Raman spectroscopy (surface enhanced Raman spectroscopy), whereby pyridine is used as probe molecule.