In this study, a novel polyimide (PI) film, consisting of multiwall carbon nanotubes (MWCNTs) dispersed in an Ionic Liquid (IL), were demonstrated to be high shielding effectiveness (SE). The film was potentially useful for screening electromagnetic interference(EMI) in an optical transceiver module. The experimental results showed MWCNT-PI composite dispersed well in IL exhibits a high far-field SE of 38 ~ 45 dB within the frequency range of 1 ~ 3 GHz. It was also demonstrated the MWCNT-PI composite prepared with IL dispersed process have higher SE and lower weight percentage of MWCNTs than those with non-IL-dispersed process. Their intermolecular forces were carefully examined in order to understand dispersion mechanisms among MWCNTs. The aggregation phenomenon of MWCNTs was known, resulting from van der Waals forces. In our study, IL was employed to disperse MWCNTs. A proposal reason was that the attractive force between cation of the IL and £k electrons of MWCNTs is greater than the van der Waals forces among MWCNTs. From conductivity measurement, percolation threshold of the IL-dispersed MWCNT-PI composite was 5.2 wt%; percolation threshold of the non-IL-dispersed MWCNT-PI composite was 11.5 wt%. Given the lower percolation threshold ,we demonstrated the successful dispersion of MWCNT by adding IL. From the results of Raman spectrometer analyses, the IL dispersion was proved to be a physical interaction. Furthermore, the IL-dispersed MWCNT-PI composite was used as package material in monopole antenna and got a near-field SE of 37dB within the frequency of 2.8 GHz. It implied that the IL-dispersed MWCNT-PI composite has an excellent EMI performance.The IL-dispersed MWCNT-PI composite is suitable for packaging low-cost and high-performance optical transceiver modules in the application of the fiber-to-the-home (FTTH) lightwave transmission systems.

Studies on charge transport properties in carbon nanotubes (CNTs) have been a subject of great interest for a long time not only as an important topic in fundamental science, but also as a basic requirement for the application of CNTs for nanoelectronics. CNTs show a wide range of transport behavior that varies from ballistic to hopping regime, depending on the dimensionality and nature of disorder in the system. Minute variations in disorder can lead from weak to strong localization, and this yields complex and intriguing features in the analysis of transport data. It is particularly important to carry out such a study for multiwall carbon nanotubes (MWCNTs), in which both dimensionality and disorder play an important role and the nature of localization is non-trivial as wave functions are extended along the tube or bundle of tubes. A proper understanding of the mechanisms of charge transport and their quantitative knowledge is an essential requirement for any possible application of CNTs in nanodevices. Such studies not only yield information on the transport parameters crucial for applications but can also provide a test for any possible microscopic theories of transport. Main focus of the current thesis is to understand the mechanism of charge transport in iron-embedded MWCNTs and to gain more knowledge on the transport behavior. Magnetically functionalized CNTs, in particular the CNTs filled with ferromagnetic materials are of profound interest for the basic scientific research as well as for technological application. Iron-embedded MWCNTs are synthesized by one step pyrolysis method. This method gives a proper route to synthesize the magnetic particles encapsulated CNTs. Beyond the geometrical advantage of a cylinder-shaped nanostructure design, the carbon shells provide an effective protection against oxidation of magnetic nanoparticles. The iron-embedded MWCNTs exhibit excellent magnetic properties like the uniaxial magnetic anisotropy, and the high coercivity, which is larger than the coercivity of bulk iron. Thus, they have significant potential for data storage devices and biomedical applications. Vertical alignment of CNTs is an important issue for device applications such as field electron emitters and flat-panel displays. Vertically aligned MWCNTs are grown on various substrates in the present work and the role of catalyst particles in vertical alignment is discussed. This thesis also reports the investigations on the magnetic properties including magnetotransport studies. The thesis is organized in seven chapters and a brief summary of each chapter is given below. Chapter 1 presents an introduction of the CNTs and its structural and electronic properties. Charge transport in CNTs is then discussed in terms of the fundamental aspects of conduction regimes and transport length scales. The synthesis and characterization of iron-embedded MWCNTs is described in chapter 2. It is important to get good quality CNTs in a scalable way. The various methods available for CNT synthesis are arc discharge, laser ablation, chemical vapor deposition etc. A one-step thermally assisted pyrolysis method employed for synthesizing MWCNTs is a simple and cost-effective method. Benzene is used as a precursor and ferrocene as a catalyst in the present case. Good quality CNTs are obtained from this method, which are of multiwall in nature (outer diameter in the range of 10-25 nm). Vertically aligned mats of MWCNTs are also obtained on the quartz substrate. The thickness of the mats is several tens of microns. The prepared MWCNTs are characterized by electron microscopic studies for its structure and surface morphology. Many iron particles are seen inside the tubes. Energy dispersive x-ray (EDX) spectra taken from the small region of the sample under TEM show the presence of iron. Raman spectra of the sample suggest good quality of the tubes. Prominent G-peak in this spectrum shows that the sample is of well-graphitic nature. X-ray diffraction pattern of MWCNT material shows the presence of -Fe and Fe3C apart from the graphitic peak. Chapter 3 describes the growth of vertically aligned MWCNTs (v-MWCNTs) on various substrates and role of catalyst particles in the alignment. The v-MWCNTs are grown on sapphire, quartz and thermally oxidized silicon substrates without pre-deposition of any catalyst. The grown MWCNT mats had a thickness of several tens of microns. Surface elemental analysis shows the presence of catalyst particles on the substrate which is essential for vertical alignment of the tubes. It is found that the order in which the precursor and the catalyst were introduced during chemical vapor deposition determines the orientation of the nanotubes. When there were no catalyst particles on the substrate in the beginning, random alignment of CNTs took place instead of vertical alignment. Base growth mode of CNTs is proposed in the present case from the results obtained. Chapter 4 deals with the magnetic properties of the as-synthesized MWCNTs. The CNTs in pristine form are of diamagnetic in nature. The ferromagnetic-like behavior arises from the iron particles embedded in MWCNTs. These ferromagnetic particles are retained in the MWCNTs automatically, as the catalyst in this case contains iron. MWCNTs of different iron weight percentage are prepared by taking different amount of ferrocene as a precursor. These particles exhibit a magnetic moment up to 98 emu/g and coercivity in the range of 500–2000 Oe. Reduced magnetization is attributed to the formation of surface shell with spin disorder and to the presence of Fe3C phase. Large coercivity compared to the bulk vale of few orested is due to the complex state of interactions, which can create strong pinning centers for the core moments during the demagnetization. In addition the observed dependence of the magnetoresistance on the direction of applied field, is correlated with the shape anisotropy of the Fe particles. The trend of saturation of magnetization at higher fields suggests that exchange coupling in the present case is one-dimensional. The charge transport properties of MWCNT mats are discussed in chapter 5. Many of the transport parameters are often affected by the presence of magnetic field. In order to gain a deeper insight into the conduction mechanism, the study of the electrical transport in presence of magnetic field is highly useful. The temperature and magnetic field dependence of the conductivity of MWCNT mat is studied in the temperature range of 1.4-150 K in the magnetic field up to 10 T. The charge transport in the system is governed by Mott’s variable-range hopping (VRH) of three-dimensional type in the higher temperature range and two-dimensional type in the lower temperature range. Mott’s various parameters like localization length, hopping length, hopping energy, and density of states at the Fermi level are deduced from the VRH fit. The hopping length decreases from 13.2 to 12.2 nm, as temperature increases from 110 to 150 K. The obtained value of hopping length around ~13 nm is within the range of nanotube diameters of 10 to 25 nm. This is the main component of the hopping length, which indicates that VRH takes place on the tube scale. The localization lengths observed in the case of 3D VRH and 2D VRH conduction are well within the range of outer diameter of MWCNTs, which indicates that the localization takes place at the tube scale along the boundaries of the tubes. If the charges are localized at the tube boundaries, then the localization length gives an average diameter of the tubes and the results obtained supports this argument. It is also important to note that the defects present in the nanotubes in the form of structural defects and bad matching of chirality gives rise to localization. There are not many reports on the effect of a magnetic field on the VRH process for MWCNT systems. The resistance of the sample decreases with the magnetic field in the direction of tube axis of the nanotubes. The magnetic field gives rise to delocalization of states as evident from the values of localization lengths at different fields. The application of magnetic field lowers the crossover temperature, at which three-dimensional VRH turns to two-dimensional VRH. The conductivity at the lower temperature side is governed by the weak localization (WL) give rise to positive magnetoconductance (MC). Here a phase diagram with temperature and magnetic field is proposed, showing different regions for different kind of transport mechanisms. This may be applicable for other class of disordered material as well. Chapter 6 deals with the magnetotransport studies on disordered MWCNT mat. The electrical conductivity and MC data are analyzed in the temperature range of 1.4-150 K and in the magnetic fields up to 11 T. The system is in the critical regime obeying conductivity of metallic systems as suggested in weak localization-electron electron interaction model. The MC is positive for the whole temperature range except at temperature below 4.2 K. Results are analyzed in the terms of weak localization, electron-electron interaction and VRH. The H 2 dependence at lower magnetic fields and H dependence at higher magnetic fields is found supporting weak localization. Inelastic scattering lengths are also deduced from the low temperature MC data and its temperature dependence shows that the dominant dephasing mechanism in the present case is inelastic electron-electron scattering in the dirty limit. Chapter 7 describes measurements on individual MWCNTs and subsequent charge transport studies. After many trials a suitable method was devised to isolate single tubes and to put contacts on it for the four probe measurement. For electrical measurements on isolated single tube, it is found that the joule heating due to excess current is an important issue. A current of the order of few µA burns the sample immediately. I-V characteristics of the MWCNTs show that the electrical contacts are ohmic and the resistance is few k. Initial electrical measurements show that there is slight decrease in resistance with increase of temperature and MR is approximately negative. This behavior suggests that signature of weak localization is present in the sample. Further studies are required in order to gain the insight into the transport mechanism for individual MWCNT. Finally, the thesis concludes with a general conclusion and future directions for this work.

The interwall spacing of multi-walled carbon nanotubes has an effect on their physical and chemical properties. Tubes with larger interwall spacing - compared to the spacing where the carbon atoms are in their natural distance to each other - are for instance expected to be mechanically less stable. Considering the MWCNT interwall spacing’s dependence on the tube size, three interesting previous studies with slightly different conclusions can be found. All of them conclude an increase of the interwall spacing with a decreasing tube size. We describe their analysis procedure, compare them to each other and to our own measured data. In the beginning of our analyses, we determine the expected inaccuracy for measured distances out of TEM images being up to 10 % and we show the impacts of the TEM’s defocus, a powerful setting in TEM imaging. Finally, we suppose that the interwall spacings are not as strongly varying as one previous study concludes, but our analyses are relatively in harmony with the two other studies. The interwall spacings from tubes with an inner diameter larger than 5 nm are relatively constant within the whole tube. Furthermore, it appears that the middle spacings (excluding the outer- and innermost ones) show values that are most consistent with the interlayer spacings of turbostratic graphite. In underfocused images, the outer- and innermost spacings tend to have values being slightly smaller than the middle ones from the same tube.

Field emission is the emission of electrons from a solid under an intense electric field, of the order of 109 V/m. Emission occurs by the quantum mechanical tunneling of electrons through a potential barrier to vacuum. Field emission sources offer several attractive features such as instantaneous response to field variation, resistance to temperature fluctuation and radiation, a high degree of focusing ability in electron optics, good on/off ratio, ballistic transport, and a nonlinear current-voltage relationship. Carbon nanotubes (CNTs) are potential candidates as field emitters since they possess high aspect ratio and are chemically inert to poisoning, and physically inert to sputtering during field emission. They can carry a very high current density and do not suffer field-induced tip sharpening like metallic tips. In addition, the CNT field emitters have the advantage of charge transport through 1D channels and electron emission at the sharp tips due to large enhancement. But the injection of electrons from the back contact remains a technical challenge which requires binding of CNT emitters to metallic substrate. Also, detachment of the CNT from the substrate tends to occur with time. The electrically conducting mixtures of CNTs and polymer can provide an alternative route to address these issues in the field emission of CNTs. The composites can be casted on any substrate in desired shape and the polymer matrix provides necessary support. The research work reported in this thesis includes the preparation of high quality multiwall carbon nanotubes (MWCNTs), MWCNT-polystyrene (PS) composites, and experimental investigation on field emission properties of MWCNT¬PS composites in two different configurations. Electrical conductivity and percolation threshold of the MWCNT-PS composites are also investigated to ensure their high quality prior to the field emission studies. The study has been further extended to reduced graphene oxide (rGO) coated on polymer substrate. The main results obtained in present work are briefly summarized below. This thesis contains eight chapters. Chapter 1 provides an overview of basics of field emission, and the potential of CNT and CNT-polymer composites as field emitters. Chapter 2 deals with the concise introduction of various structural characterization tools and experimental techniques employed in this study. Chapter 3 describes the synthesis of MWCNTs and characterization by using electron microscopy and Raman spectroscopy. MWCNTs are synthesized by chemical vapor deposition (CVD) of toluene [(C6H5) CH3] and ferrocene [(C5H5)2 Fe] mixture at 980 °C. Here toluene acts as carbon source material and ferrocene provides catalytic iron (Fe) particles. The MWCNT formation is based on the thermal decomposition of the precursor mixture. Scanning electron microscopy (SEM) characterization shows that the MWCNTs are closely packed and quite aligned in one direction. The average length of MWCNTs is about 200 μm and outer diameter lies in the range of 50-80 nm. The high quality of as-prepared MWCNT sample is confirmed by Raman spectroscopy. The as-grown MWCNTs are encapsulated with catalytic Fe nanoparticles, revealed by transmission electron microscopy. The Fe nanoparticles trapped within the MWCNT serve as fantastic system for studying the magnetic properties. Three types of MWCNT samples filled with Fe nanoparticles of different aspect ratio (~10, 5 and 2) are synthesized by varying the amount of ferrocene in the precursor material, and their magnetic properties are investigated. Enhanced values of coercivity (Hc) are observed for all samples, Hc being maximum (~2.6 kOe) at 10 K. The enhancement in Hc values is attributed to the strong shape anisotropy of Fe nanoparticles and significant dipolar interactions between Fe nanoparticles. Chapter 4 deals with the field emission studies of MWCNT-PS composites in the parallel configuration. By incorporating as-prepared MWCNTs in PS matrix in a specific ratio, composites with varying loading from 0.01-0.45 weight (wt.) fraction are prepared using solution mixing and casting. High degree of dispersion of MWCNTs in PS matrix without employing any surfactant is achieved by ultrasonication. Low percolation threshold (~0.0025 wt. fraction) in the MWCNT-PS composites ensures the good connectivity of filler in the fabricated samples. Field emission of MWCNT¬PS composites is studied in two different configurations: along the top surface of the film (parallel configuration) and along the cross section of the sample (perpendicular configuration). In this chapter field emission results of the MWCNT-PS composites in parallel configuration are presented. The effect of charge transport in limiting the field emission of MWCNT-PS composite is discussed. Field emission results of MWCNT-PS composites in parallel configuration indicate that the emission performance can be maximized at moderate wt. fraction of MWCNT (0.15). The obtained current densities are ~10 µA/cm2 in the parallel configuration. Chapter 5 presents the study of field emission characteristics of MWCNT¬PS composites of various wt. fractions in the perpendicular configuration. Till date most studies using nanotube composites tend to have the nanotubes lying in two dimensional plane, perpendicular to the applied electric field. In the perpendicular configuration, the nanotubes are nearly aligned parallel to the direction of the applied electric field which results in high field enhancement, and electron emission at lower applied fields. SEM micrographs in cross-sectional view reveal that MWCNTs are homogeneously distributed across the thickness and the density of protruding tubes can be scaled with wt. fraction of the composite film. Field emission from composites has been observed to vary considerably with density of MWCNTs in the polymer matrix. High emission current density of 100 mA/cm2 is achieved at a field of 2.2 V/µm for 0.15 wt. fraction. The field emission is observed to follow the Fowler– Nordheim tunneling mechanism, however, electrostatic screening plays a role in limiting the current density at higher wt. fractions. Chapter 6 highlights the field emission response of rGO coated on a flexible PS film. Field emission of rGO coated PS film along the cross section of the sample is studied in addition to the top film surface of the film. The effect of geometry on the improved field emission efficiency of rGO coated polymer film is demonstrated. The emission characteristics are analyzed by Fowler–Nordheim tunneling for field emission. Low turn-on field (~0.6 V/µm) and high emission current (~200 mA/cm2) in the perpendicular configuration ensure that rGO can be a potential field emitter. Furthermore, stability and repeatability of the field emission characteristics are also presented. Chapter 7 deals with the synthesis, characterization, and field emission of two different kinds of hybrid materials: (1) MWCNT coated with zinc oxide (ZnO) nanoparticles (2) ZnO/graphitic carbon (g-C) core-shell nanowires. The field emission from the bucky paper is improved by anchoring ZnO nanoparticles on the surface of MWCNT. A shift in turn on field from 3.5 V/µm (bucky paper) to 1.0 V/µm is observed by increasing the ZnO nanoparticle loading on the surface of MWCNT with an increase in enhancement factor from 1921 to 4894. Field emission properties of a new type of field emitter ZnO/g-C core-shell nanowires are also presented in this chapter. ZnO/g-C core/shell nanowires are synthesized by CVD of zinc acetate at 1300 °C. Overcoming the problems of ZnO nanowire field emitters, which in general possess high turn on fields and low current densities, the core-shell nanowires exhibit excellent field emission performance with low turn on field of 2.75 V/µm and high current density of 1 mA/cm2. Chapter 8 presents a brief summary of the important results and future perspectives of the work reported in the thesis.

Carbon nanotubes (CNTs) have been recognized as potential candidates for mainstream device fabrication and technologies. CNTs have become a topic of interest worldwide due to their unique mechanical and electrical properties. In addition, CNTs possess high aspect ratio and low density that make them an important material for various technological applications. The field of carbon nanotube devices is rapidly evolving and attempts have been made to use CNTs in the fabrication of devices like field emitters, gas sensors, flow meters, batteries, CNT-field effect transistors etc. These molecular nanostructures are proposed to be an efficient hydrogen storage material. CNT cylindrical membranes are reported to be used as filters for the elimination of multiple components of heavy hydrocarbons from petroleum and for the filtration of bacterial contaminants of size less than 25 nm from water. Recently, CNT bundles have been proposed to be a good material for low-temperature sensing. CNTs have also been considered as promising filler materials due to extraordinary characteristics mentioned above. Fabrication of nanocomposites using CNTs as reinforcing material has completely renewed the research interest in polymer composites. The conductive and absorptive properties of insulating polymer doped with conducting filler are sensitive to the exposure to gas vapors and hence they can be used in monitoring various gases. The application of fiibre reinforced polymer composites in aeronautic industry are well known due to their high mechanical strength and light weight. Also, the conductive composite materials can be used for electromagnetic shielding. Desired properties in CNT-composites can be attained by adding small amount of CNTs in comparison to traditional filler materials. Due to high aspect ratio and low density of CNTs, percolation threshold in CNT-polymer composites can be achieved at 0.1 vol % as compared to ~16 vol. % in case of carbon particles. The research work ׽0.1 vol. %, as compared to reported in this thesis includes the preparation of multiwall carbon nanotube (MWNTs) and MWNT-polystyrene composites, experimental investigations on low temperature charge transport, and magnetic properties in these systems. This thesis contains 7 chapters. Chapter 1 provides an overview of CNTs and CNT-polymer composites. This chapter briefly describes the methods for synthesizing CNTs and fabricating CNT-polymer composites, charge transport mechanisms in CNTs and composites, and their magnetic properties as well. Chapter 2 deals with the concise introduction of various structural characterization tools and experimental techniques employed in the present work. An adequate knowledge of the strengths and limitations of experimental equipment can help in gathering necessary information about the sample, which helps in studying and interpreting its physical properties correctly. Chapter 3 describes the synthesis of MWNTs and their use as filler material for the fabrication of composites with polystyrene (PS). The characterization results of as-prepared MWNT and composites show that MWNTs possess high aspect ratio (~4000), and are well dispersed in the composite samples (thickness ~50-70 µm). The composite samples are prepared by varying the MWNT concentration from 0.1 to 15 wt %. The as¬fabricated composites are electrically conductive and expected to display novel magnetic properties since MWNTs are embedded with iron (Fe) nanoparticles. Chapter 4 presents the study of charge transport properties of aligned and random MWNTs in the temperature range 300-1.4 K. The low temperature electrical conductivity follows the weak localization (WL) and electron-electron (e-e) interaction model in both samples. The dominance of WL and e-e interaction is further verified by magneto-conductance (MC) measurements in the perpendicular magnetic field up to 11 T at low temperatures. The MC data of these samples consists of both positive and negative contributions, which originates from WL (at lower fields and higher temperatures) and e-e interaction (at higher fields and lower temperatures). Chapter 5 contains the results of charge transport studies in MWNT-PS composite near the percolation threshold (~0.4 wt %) at low temperatures down to 1.4 K. Metallic-like transport behavior is observed in composite sample of 0.4 wt %, which is quite unusual. In general, the usual activated transport is observed for systems near the percolation threshold. The unusual weak temperature dependence of conductivity in MWNT-PS sample at percolation threshold is further verified from the negligible frequency dependence of conductivity, in the temperature range from 300 to 5 K. Chapter 6 accounts on the experimental results of magnetization studies of MWNTs and MWNT-PS composites. The observation of maxima in coercivity and squareness ratio at 1 wt % of Fe-MWNT in a polymer matrix show the dominance of dipolar interactions among the encapsulated Fe-nanorods within MWNTs. The hysteresis loop of 0.1 wt % sample shows anomalous narrowing at low temperatures, which is due to significant contribution from shape anisotropy of Fe-nanorods. Chapter 7 presents brief summary and future perspectives of the research work reported in the thesis.

Ever since their discovery, Carbon nanotubes (CNTs) have been renowned to be potential candidates for a variety of applications. Nevertheless, the difficulties accompanied with their dispersion and poor solubility in various solvents have hindered CNTs potential applications. As a result, studies have been developed to address the dispersion problem. The solution is in modifying the surfaces of the nanotubes covalently or non-covalently with a desired dispersant. Various materials have been employed for this purpose out of which polymers are the most common. Non-covalent functionalization of CNTs via polymer wrapping represents an attractive method to obtain a stable and homogenous CNTs dispersion. This method is able to change the surface properties of the nanotubes without destroying their intrinsic structure and preserving their properties. This thesis explores and studies the surface modification and solublization of pristine single and multiwalled carbon nanotubes via a simple solution mixing technique through non-covalent interactions of CNTs with various anionic and cationic conjugated polyelectrolytes (CPEs). The work includes studying the interaction of various poly(phenylene ethynylene) electrolytes with MWCNTs and an imidazolium functionalized poly(3-hexylthiophene) with SWCNTs. Our work here focuses on the noncovalent modifications of carbon nanotubes using novel CPEs in order to use these resulting CPE/CNT complexes in various applications. Upon modifying the CNTs with the CPEs, the resulting CPE/CNT complex has been proven to be easily dispersed in various organic and aqueous solution with excellent homogeneity and stability for several months. This complex was then used as a nanofiller and was dispersed in another polymer matrix (poly(methyl methacrylate), PMMA). The PMMA/CPE/CNT composite materials were cast or electrospun depending on their desired application. The presence of the CPE modified CNTs in the polymer matrix has been proven to enhance the composites thermal, mechanical and electrical properties compared to pristine CNTs. Various spectroscopic and microscopic techniques such as UV-vis, fluorescence, TEM, AFM and SEM were used to study and characterize the CPE/CNT complexes. Also, TGA, DSC and DMA were used to study the thermal and mechanical properties of the composite materials. Our current work represents a fundamental study on the non-covalent interactions between CNTs and CPEs on one hand and gives a real life example on the CPE/CNT application in composite materials and electronics.

Yes / This paper investigates the coupled effect of functionalized multiwall carbon nanotubes (MWCNTs-COOH), nanomontmorillonite (NM), and sodium dodecyl benzene sulfonate (SDBS) anionic surfactant on compressive and flexural strengths of cement paste. The response surface methodology (RSM) was used to optimize the content of the two nanomaterials and surfactant, and to analyze the effect of their interactions on mechanical properties and microstructural characteristics of the paste. Test results indicate that the simultaneous use of NM and MWCNT can lead to 30% gain in compressive strength and 40% increase in flexural strength. Using analysis of variance, it was possible to predict the optimal weight percentage of nanomaterials. Atomic Force Microscope observations showed that the use of NM and MWCNT can reduce the surface roughness of cement paste and refine porosity, thus reducing the risk of cracking at the cement matrix and improving the homogeneity of the microstructure.

The advancement of each component of aerospace vehicles is necessary as the continual demand for more aggressive missions are created. Improvements in propulsion and guidance system electronics are invaluable; however without material development to protect the vehicle from its environment those advances will not have a practical application. Thermal protection systems (TPS) are required in both external applications; for example on reentry vehicles, as well as in internal applications; to protect the casing of rockets and missiles. This dissertation focuses on a specific type of internal solid rocket motor TPS, ablatives. Ablatives have been used for decades on aerospace vehicles. To protect the motor from the hostile environment, these materials pyrolyze and char. Both of these mechanisms produce a boundary between the combustion gases and the motor as well as release the heat that the decomposed material has absorbed. These sacrificial materials are intended to protect the casing that it is attached to. With the development of polymer nanocomposites (PNCs) in the last couple of decades, it is of interest to see how these two fields can merge. Three different nanomaterials (carbon nanofibers, multiwall carbon nanotubes, and nanoclays) are examined to observe how each behaves in environments that simulate the motor firing conditions. These nanomaterials are individually added to a thermoplastic polyurethane elastomer (TPU) at different loadings, creating three distinct families of polymer nanocomposites. To describe a materials ablative performance, a number of material properties must be individually studied; such as thermal, density, porosity, char strength, and rheology. Different experiments are conducted to isolate specific ablative processes in order to identify how each nanomaterial affects the ablative performance. This dissertation first describes each material and the ablative processes which are characterized by each experiment. Then basic material properties of each family of materials are described. Degradation and flammability experiments then describe the degassing processes. Studies of the material char are then performed after full blown rocket experiments are done. These tests have shown that of the three nanomaterials, nanoclay enhances the TPU ablative performance the most while the CNF provides the least enhancement. / text

Vertically aligned Multiwalled Carbon Nanotubes (MWCNTs) were grown in the pores of Anodized Aluminum Oxide (AAO) templates and investigated for resistive sensor applications. High Sensitivity of 23% to low concentration (100 ppm) of ammonia was observed. An equivalent circuit model was developed to understand the current flow path in the resistive sensor. This helped us in achieving high sensitivities through amorphous carbon (a-C) layer thickness tailoring by employing post-growth processing techniques like plasma etching. A simulation model in MATLAB was developed to calculate the device resistance and the change in the sensitivity as a function of device parameters. The steady state response and transient response of the model to the number of ammonia molecules and its adsorption rate were studied. Effects of oxygen plasma, argon plasma and water plasma etch on thinning of the a-C layer were studied. In order to enhance the sensitivity, the top and bottom a-C layers were replaced by a more conductive metal layer. This also helped in understanding the current flow in the device and in the estimation of the resistivity of the a-C layer.

Multiwall carbon nanotubes (MWNTs) have extraordinary mechanical and thermal transport properties. They significantly improve the static and dynamic mechanical properties of acrylic orthopaedic bone cement when added to the dry cement polymer powder. Understanding the role MWNTs play on bone cement polymerization temperatures will lead to improved mechanical integrity of the cement-bone interface in joint arthroplasties. It was determined through thermal testing that MWNTs increased the polymerization time of the methylmethacrylate by 45-460% and decreased the peak exothermic temperature of bone cement with and without antibiotics. The flow of heat produced during polymerizing cement was reduced 25-85% with the addition of MWNTs to the cement powder. This decreases the probability of thermal necrosis and “hot” spots caused by high exothermic polymerization temperatures that can destroy the bone adjacent to the cement. These high temperatures also affect the potency and range of antibiotics used in arthroplasty. Isothermal and elution studies determined that MWNTs altered the heat flow and amount of antibiotic release from bone cement during polymerization. Antibiotic elution from bone cement containing MWNTs could match the elution seen in pure cement. The alteration of the flow of heat from bone cement leads to new options for heat-labile antibiotics in total joint arthroplasty.