The interactions which occur between both polar and non-polar fluid phases and surfaces of various carbon materials: Activated Carbon (AC), non-porous Carbon Black (CB) and Multiwall Carbon Nanotubes (MWCNTs)with different surface chemistry have been studied. These are currently of great interest as they govern the interfacial behaviour of carbons in a wide range of applications; separation adn composite technologies being two prime examples. Consequently, techniques for chemical modification of carbon surfaces ar also of interest. Surface oxygen functional groups have been introduced, or modified, using the following oxidation techniques: liquid-phase oxidation (both AC and CB), Fenton and Birch reduction treatment (MWCNTs) and in a more controlled manner using gas-phase ozone treatment (CB). The chemistry of all the resulting carbon surfaces were characterised using X-ray Photoelectron Spectroscopy (XPS), which gives a quick and direct quantitative measure of the external surface composition. This technique, which has not yet been extensively employed in detailed adsorption studies, is a promising alternative to Temperature Programmed Desorption (TPD) and Boehm titration method in the determination of oxygen and other surface groups. Physical effects of the various surface modifications have been studied using a variety of techniques appropriate for the material in question. Scanning Electron Microscopy (SEM) images show some deteriorating effects of the liquid-phase oxidations on the structure of both activated carbon and carbon black materials. Conversely, surface areas from nitrogen adsorption at 77oK, coupled witj immersion calorimetry data for toluene, show thet the physical structure of the carbon blacks is not modified by ozone treatment. This has allowed a detailed study of the effects of surface oxygen level (i.e. polarity) on vapour adsorption. Regarding the MWCNT materials, detailed High-Resolution Electron Microscopy (HRTEM) photographs show that the multi-wall structure of the nanotubes in not significantly disrupted during the introduction of active functional groups by the Fenton or Birch treatment and therefore keeping intact their mechanical properties which augurs well for their use as reinforcement in composite structures whilst also improving their dispersion properties in polar fluids. A systematic shift to higher adsorption values, due to the increasing specific interactions between the alcohol -OH groups and the surface oxygen groups, is observed in all the isotherms of alcohols from the CB series as the total surface oxygen concentration ([O]T) increases. Moreover, this effect was observed to be most significant for methanol confirming that the mechanism of adsorption is dominated by hydrogen bonding and therefore dependant on the surface concentration of oxygen sites; whereas it becomes less marked in the case of ethanol and isopropanol respectively due to the increasing non-specific, dispersion, interactions of the alkyl chain with the non-polar carbon surface. Overall correlations were observed between the surface oxygen concentration [O]T, the resulting enthalpy of immersion -^Hi values and the characteristic energy E of the Dubinin-Radushkevich-Kaganer (DRK) equation obtained for toluene and these alcohols and the influence of the carbon surface chemistry on the character of the adsorption isotherms is also discussed. This behaviour is also observed and much more pronounced in the case of water adsorption on other oxidised carbon materials (AC, CB and MWCNT) due to the higher polarity of water molecules. The water adsorption data were analysed using in particular the Dubinin-Serpinsky (DS) equation and also some of its recent variations such as Barton and D'Arcy & Watt equations. The DS2 and various Barton equations were found to fit best the AC and CB materials modified by liquid-phase oxidations and also for the CB 03 series with increasing level of oxidation while both D'Arcy & Watt equations gave the best fittings for the MWCNTs materials. It was also shown that the resulting parameters ao (for the DS equation) describing the surface concentration of primary polar adsorption sites and as the limiting water adsorption value were both linked to the surface oxygen level [O]T. Regarding interfacial bonding, the oxidised CB and MWCNT materials are expected to show an improved physicochemical wetting of their surfaces by various resin compunds

Electron Beam Induced Deposition (EBID) is an emerging additive nanomanufacturing tool which enables growth of complex 3-D parts from a variety of materials with nanoscale resolution. Fundamentals of EBID and its application to making a robust, low-contact-resistance electromechanical junction between a Multiwall Carbon Nanotube (MWNT) and a metal electrode are investigated in this thesis research. MWNTs are promising candidates for next generation electrical and electronic devices, and one of the main challenges in MWNT utilization is a high intrinsic contact resistance of the MWNT-metal electrode junction interface. EBID of an amorphous carbon interface has previously been demonstrated to simultaneously lower the electrical contact resistance and to improve mechanical characteristics of the MWNT-electrode junction. In this work, factors contributing to the EBID formation of the carbon joint between a MWNT and an electrode are systematically explored via complimentary experimental and theoretical investigations. A comprehensive dynamic model of EBID using residual hydrocarbons as a precursor molecule is developed by coupling the precursor mass transport, electron transport and scattering, and surface deposition reaction. The model is validated by comparison with experiments and is used to identify different EBID growth regimes and the growth rates and shapes of EBID deposits for each regime. In addition, the impact of MWNT properties, the electron beam impingement location and energy on the EBID-made carbon joint between the MWNT and the metal electrode is critically evaluated. Lastly, the dominant factors contributing to the overall electrical resistance of the MWNT-based electrical interconnect and relative importance of the mechanical contact area of the EBID-made carbon joint to MWNT vs. that to the metal electrode are determined using carefully designed experiments.

Multifunctional materials both with damping properties and strain sensing properties are very important. They promise to be more weight-efficient, and provide volume-efficient performance, flexibility and potentially, less maintenance than traditional multi-component brass-board systems. The goal of this dissertation work was to design, synthesize, investigate and apply polyaniline/Multiwall carbon nanotube (PANI/MWCNT) and polyurethane (PU) /MWCNT composites films for structural vibration control and strain sensors using free layer damping methods and static and dynamic strain sensing test methods. The PANI/MWCNT was made by in situ polymerization of PANI in the presence of MWCNT, then frit compression was used to make circular and rectangular PANI/MWCNT composite films. PU/MWCNT composites were made by the layer-by-layer method. Free end vibration test results showed both of PANI/MWCNT and PU/MWCNT have better damping ratios than each of their components. Static sensing test indicated that though there appears to be residual strain in both composite sensors after the load is removed, both the sensor and the foil strain gage react linearly when re-engaged. A drift test of the sensor showed that it is stable. The dynamic sensing test results showed that over the range of 10-1000 Hz, the PANI/MWCNT composite sensor was consistently superior to foil strain gage for sensing purposes since the highest peak consistently corresponded to the input frequency and was much higher, for example, at 20 Hz, 820 times higher than those of the strain gage. Using the same criterion, the PU/Buckypaper composite sensor was comparable to or superior to the foil strain gage for sensing purposes over the range of 10 Hz to 200 Hz. The relationship of loss factor, η, and beam coverage length, L1/L, is discussed for single sided and double sided attachment. For both PANI/MWCNT and PU/MWCNT, the loss factor, η, was found to increase as coverage length, L1/L, increases. The loss factor, η, was found to have a maximum as with coverage length, L1/L, as the coverage length continues to increase. The trend for double sided attachment was found to follow the trends discussed by Rao (2004) and Levy and Chen (1994) for viscoelastic material constrained damping.

The hybrid nanostructures exhibit excellent performances in various fields such as catalysis, sensing, and energy conversion as compared to their individual ones. The thesis deals with the new methods for the synthesis of different type of hybrids with doped/pristine carbon nanostructures in the form of graphene, multiwall carbon nanotubes (MWCNTs) as one component and metals nanostructures (Ag, Pd, Pt and Au), carbide (Fe3C), metal chalcogenides (Ni3S2 and Co9S8) and oxide (CoO) as the other components. Various synthesis techniques such as modified galvanic replacement reaction at room temperature, hydrothermal, microwave and pyrolysis have been explored for the synthesis of different hybrid nanostructures. Furthermore, various hybrid nanostructures have been explored for various catalytic activities such as oxygen reduction reaction (ORR), oxygen evolution reaction (OER) and 4-nitrophenol (4-NP) reduction. It may be noted that the ORR and OER which are undoubtedly vital for their applications in fuel cells, metal-air batteries and water oxidation reaction. Interestingly, the catalytic activities of these hybrid nanostructures are comparable or better as compared to the commercial benchmark precious catalysts.

One of the most significant issues in nanocomposite performance is improving the dispersion of carbon nanotubes (CNTs) in thermosetting or thermoplastic polymers in order to gain good mechanical properties. Several studies have investigated the fabrication of nanocomposites based on carbon nanotubes and analysed properties, but there is still insufficient data on their structure-property relationships. This thesis has investigated the central importance of stress transfer Raman studies in epoxy composites reinforced with single-walled carbon nanotubes (SWCNTs), double-walled carbon nanotubes (DWCNTs) and multiwall carbon nanotubes (MWCNTs) to elucidate the reinforcing ability of the CNTs in an epoxy matrix. This project was undertaken to synthesise and characterize MWCNTs and determine the effect of different weight fractions of untreated MWCNTs on the stress transfer efficiency at the MWCNTS / epoxy interface and on the stiffness of the thermomechanical properties of the MWCNTS / epoxy composites. It was undertaken to assess the stress transfer efficiency at the CNT / epoxy interface and at the inter-walls of the CNTs with tensile deformation and with cyclic loading.Optimized conditions of the injection chemical vapour deposition method (CVD), such as long injection times were applied to produce MWCNTs with a high yield, high aspect ratio and well-defined G' Raman peak. The morphology and size of CNTs were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) while their thermal stability was examined by Thermogravimetric analysis (TGA). Both Raman spectroscopy and mechanical testing (static and dynamic) were utilized in this study. The Raman spectroscopy research consisted of following the G'-band frequency and linewidth as well as the intensity of radial breathing modes (RBMs) during tensile deformation. The stress-induced Raman shifts in the nanocomposites have been shown to be controlled by the number of carbon nanolayers. A theory has been developed to determine and simulate the stress transfer efficiency parameter, (k_i) for MWCNTs. Tensile tests and dynamic mechanical testing were used to assess the mechanical properties of the nanocomposites.The most obvious finding to be drawn from the present study is that the reinforcement of the epoxy resin with different loadings of MWCNTs is useful, but the best reinforcement was at low loadings of MWCNTs. One of the more significant findings to emerge from this study is that (k_i) between the inner walls of the DWCNTs and MWCNTs are quite similar (~0.7), which suggest that (k_i) may be similar for all CVD MWCNTs and DWCNTs. The second major finding was that there were RBM intensity variations for the SWCNTs and DWCNTs in the hot-cured epoxy composites and that for the DWCNTs both the inner and outer nanotube walls are stressed during deformation

Thesis (M.Sc. (Chemistry)) -- University of Limpopo, 2015 / The study has focused on the effects of different acids treatments on the nanostructure of MWCNTs; doping metal oxides (copper oxide (CuO), Iron (III) oxide (Fe2O3), nickel oxide (NiO) and cobalt oxide (Co3O4)) on MWCNTs and investigates their electrochemical hydrogen and energy storage capabilities. Fourier transform infrared (FTIR) confirmed the formation of functional groups on the surface of the acid treated MWCNTs. X-ray diffraction (XRD) showed that the graphitic structure of the MWCNTs was retained after treatment with mild acids (nitric acid (HNO3), hydrogen peroxide (H2O2), a mixture of the acids, hydrogen peroxide: nitric acid (H2O2:HNO3) and hydrogen peroxide: sulfuric acid (H2O2:H2SO4)). Transmission electron microscopy (TEM) confirms the removal of bamboo carbon structures inside the inner tubes of the MWCNTs after treatment with mild acids. Brunauer-Emmet- Teller (BET) showed an increase in the surface area of mild acids treated MWCNTs. Thermogravimetric analysis (TGA) results demonstrated that the thermal stability of MWCNTs increases after treatment with mixtures of the acids. Different metal oxides treated at different temperatures were incorporated into MWCNTs (treated by a mixture of H2O2:HNO3). X-ray diffraction (XRD), scanning electron microscopy (SEM) and Transmission electron microscopy (TEM) confirmed the presence of different metal oxides inside/on the surface of the acid treated MWCNTs. The MWCNTs treated by H2O2:HNO3 gave both the highest discharge capacity (72.63 mAh/g) and capacitance (8.61 F/g), as compared to the other electrode materials. The improved hydrogen storage capacity and specific capacitance can be attributed to high surface area, wider pore size distribution and the amount of functional groups on the surface of H2O2:HNO3-treated MWCNTs; with the functional groups acting as electron transmitters. The 5wt.% CuO@300oC-MWCNTs composite showed the highest hydrogen storage capacity of 159 mAh/g. This capacity was further improved by addition of manganese oxide resulting in the highest discharge capacity of 172 mAh/g (which is equivalent to 0.64 wt.% of hydrogen stored). The highest specific capacitance of 9.70 F/g was obtained on 5wt% Fe2O3@400oCMWCNTs composite.

Next generation polymer composites that utilize the high electrical conductivity and tensile strength of carbon nanotubes are of interest. To effectively disperse carbon nanotubes into polymers, a more fundamental understanding of the polymer/nanotube interface is needed. This requires the development of new analytical methods and techniques for measuring the adhesion between a single molecule and the sidewalls of carbon nanotubes. Atomic Force Microscopy is an integral tool in the characterization of materials on the nanoscale. The objectives of this research were to: 1) characterize the binding force between single molecules and the backbone of a single walled carbon nanotube (SWNT), and 2) measure and interpret the mechanical response of carbon-based nano-objects to compressive loads using an atomic force microscope. To identify chemical moieties that bind strongly to the sidewall of the nanotubes, two experimental approaches have been explored. In the first, force volume images of SWNT paper were obtained using gold-coated AFM tips functionalized with terminally substituted alkanethiols and para-substituted arylthiols. Analysis of these images enabled quantification of the adhesive interactions between the functionalized tip and the SWNT surface. The resultant adhesive forces were shown to be dependent upon surface topography, tip shape, and the terminal group on the alkanethiol. The mechanical response of several single- and multi-walled carbon nanotubes under compressive load was examined with an AFM. When the scanner, onto which the substrate has been mounted, was extended and retracted in a cyclic fashion, cantilever deflection, oscillation amplitude and resonant frequency were simultaneously monitored. By time-correlating cantilever resonance spectra, deflection and scanner motion, precise control over the length of nanotube in contact with the substrate, analogous to fly-fishing was achieved. This multi-parameter force spectroscopy method is applicable for testing the mechanical and interfacial properties of a wide range of nanoscale objects. This research has led to a clearer understanding of the chemistry at the nanotube/polymer interface, as well as the mechanical response of nanoscale materials. A new force spectroscopic tool, multi-parameter force spectroscopy, should be extremely helpful in characterizing the mechanical response of a myriad of nanoscale objects and enable nanoscale devices to become a reality.

The main motivation in this thesis is to compare the conformation and charge transport in conducting polymers and carbon nanotubes (CNTs) and to investigate those physical properties in their combined form of nanocomposites. It is known that both conducting polymers and carbon nanotubes are intrinsically 1-dimensional systems which consist of delocalized π-electrons. However, the main difference between these is the fact that flexibility of conducting polymers can be varied depending on the extent of conjugation while CNTs are rigid. Hence a comparison of electronic properties as correlated to their morphology has been carried out and their individual role in nanocomposites is further studied. The thesis consists of 6 chapters and appendix. Chapter 1 consists of brief introduction of general properties of both conducting polymers, CNTs and their nanocomposites. Chapter 2 deals with the sample preparation and experimental techniques used for the work. Chapter 3 elaborates on the conformational / structural studies on the systems. Chapter 4 focuses on the transport measurements to study the electronic properties of the samples. Chapter 5 reveals the magnetic properties of these systems which can be applied in technological devices. And chapter 6 gives the conclusion and future directions of the work being done. Chapter 1: Nanocomposites represent a guest-host matrix consisting of easily processible functionalized conjugated polymer as host, incorporating carbon nanotubes as fillers with versatile electronic and magnetic properties, which provide a wide range of technological applications. The conformation, charge dynamics as well as magnetic properties of these conducting polymers and carbon nanotubes, and various aspects of transport mechanism and spin dynamics present in the nanocomposite matrix are studied and presented in a consistent framework. Chapter 2: The multiwall carbon nanotubes (MWNTs) are grown by thermal chemical vapor deposition (CVD). The MWNTs are dispersed in solution of conducting polymers by ultrasonication and then the suspension is cast on glass substrate and slowly dried by moderate heating. Once dried completely, the free-standing films of thickness 15-25 μm are peeled off the substrate for measurements. The MWNTs, above a certain concentration, form an interconnected network in the 3-dimensional polymer matrix, following percolation mechanism. The disorder is brought into the system mainly by bundling of tubes and bundle intersections. The morphology and conformation of the samples are studied by SEM, TEM and small angle X-ray scattering (SAXS) techniques. Chapter 3: Small angle X-ray scattering (SAXS) studies in polymeric systems are carried out to probe local nanoscale morphology at various length scales to show the correlation among conformation and assembly of chains. Small angle X-ray scattering (SAXS) studies are carried out in poly [2-methoxy5-(2’–ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) solution of varying conjugation lengths as well as different solvents. By increasing the extent of πconjugation from 30 to 100 %, the persistence length increases by a factor of three. Moreover, a pronounced second peak in the pair distribution function is observed in fully conjugated chain, at larger length scales which indicates that the chain segments tend to self-assemble as the conjugation along the chain increases. The chain assembly and aggregation are further studied for suspensions of MWNTs in polyethylene dioxythiophene-polystyrene (PEDOT-PSS) with aqueous medium and DMSO (dimethyl sulphoxide). The SAXS profile of MWNT dispersion in aqueous PEDOT-PSS clearly show rigid-rod feature of the individual nanotubes evident by the q-1 behavior at short ranges. The crossover from q-1 to q-2 in the longer range further suggest that the suspension consists of individual nanotubes, nanotubes bundles and aggregates that give rise to a 3-dimensonal meshwork of intersecting tubes and ropes. For the MWNT dispersion in PEDOT-PSS with DMSO, however, such q-1 behavior is absent; which evidently shows that the rods are not isolated in the solution and are rather agglomerated. How these conformations affect the electrical and magnetic properties of these systems are studied further in Chapter 4. Chapter 4: Transport mechanism in single wall carbon nanotubes (SWNT), MWNT pellets, and nanocomposite films of MWNT and PEDOT-PSS is studied. The positive and negative magnetoresistance (MR) data in various SWNT samples are analyzed by taking into account the electron-electron interaction (EEI) contribution, in addition to the weak localization (WL) regime. The contribution from EEI to the total MR is confirmed from the universal scaling of MC relation showing that EEI plays a significant role at higher fields and lower temperatures. Intrinsic parameters like inelastic scattering length extracted for barely metallic sample follows the T-3/4 dependence due to inelastic electron-electron scattering in the dirty limit. Conductivity and magnetoresistance (MR) measurements on nanocomposite films with varying MWNT content (0.03 - 3 %) are performed at a field range 0-11 Tesla, and temperature range 1.3–300 K. The temperature dependence of resistance above 4 K suggests a Coulomb-gap variable range hopping (CG-VRH) transport in the network. Alhough solely negative MR (~ 5-6 %) is observed for pristine MWNT pellets; the nanocomposite films show a combination of large negative MR (~ 80 %) at T < 4 K, and a comparatively weaker positive MR (~ 30 %) for T > 4 K. This suggest that there are two mechanism interplaying and dominant at different temperature regimes which can be explained by the mechanism of transport of the charge carriers of MWNT intervened by that of the polymer matrix. In conclusion how the individual properties of conducting polymer and carbon nanotubes contribute to the unique electronic and conformational properties in their nanocomposites is framed in this investigation. Chapter 5: Magnetic properties of the pristine MWNTs as well as metal nanowires of nickel, nickel-iron (NiFe), nickel-iron-cobalt (NiFeCo) encapsulated in the MWNTs are studied using superconducting quantum interference device (SQUID) magnetometer. A typical example of Ni nanowires encapsulated in MWNT (Ni-MWNT) is taken and the results are compared to other forms of nickel (bulk, nanorod cluster, nanowire) to see the effect of size, shape and environment on the magnetic kproperties. The saturation magnetization and coercivity for Ni-MWNTs are 1.0 emu/gm and 230 Oe. The temperature dependence of magnetization indicates superparamagnetic which is supported by the field-cooled and zero-field-cooled plots determining a blocking temperature ~ 300 K. These altered magnetic properties of Ni-MWNTs are mainly due to the contribution from carbon nanotube encapsulation. Both the shape and environment enhance the total magnetic anisotropy of encapsulated nanowires at least by a factor of four. The encapsulation of metal nanowires in MWNTs tunes the magnetic properties of the system widely, e.g. from diamagnetic (pristine MWNTs) to paramagnetic (Ni-MWNT) to ferromagnetic (NiFe-MWNT) and a combination of para and ferro (NiFeCo-MWNT). Chapter 6: The conclusions of the different works presented in the thesis are coherently summarized in this chapter. Thoughts for future directions are also summed up. Appendix A: Spin dynamics in conducting polymer PEDOT-PSS in its pristine, processed with DMSO and nanocomposite form (with carbon nanotubes) is studied using solid state nuclear magnetic resonance (NMR). Plots of proton spin lattice relaxation times vs. temperature at a fixed frequency 23.4 MHz are compared to study the effect of the external agents on the polymer dynamics.

In recent years, increased use of electronic devices and wireless operations resulted in unavoidable electromagnetic (EM) pollution which has a significant impact on civil and military sectors. Considering the foremost requirement, huge efforts were invested in the development of electromagnetic interference (EMI) shielding materials. In this context, metals are usually preferred but design complexities like high density and susceptibility towards corrosion are limiting factors; additionally, the reflection of microwaves from the surface fails to serve as EM absorbers. The concern here is to minimize the reflection of the high frequency electromagnetic wave from the surface and to enhance the microwave absorption in GHz frequencies. In this thesis, we have made an attempt to design EMI shielding materials with exceptional absorption ability derived from Polycarbonate (PC)/ Poly styrene-co-acrylonitrile (SAN) based polymer blends. Herein, unique co-continuous micro-phase separated blend structures with selective localization of microwave active nanoparticles in one of the phases were realized to be most effective for microwave attenuation over just dispersing it in one polymer matrix (i.e. PC and SAN composites). The synergistic attenuation of electric and magnetic field associated with EM radiation was achieved through incorporation of various magnetic nanoparticles, however, dispersion of magnetic nanoparticles was a challenging task. Therefore, in order to localize magnetic nanoparticles in PC phase of the blends and to enhance the dispersion state, various modification strategies have been designed. In summary, we have developed a library of engineered nanoparticles to achieve synergistic attenuation of EM radiation mostly through absorption. For instance, the PC/SAN blends containing MWNTs and rGO-Fe3O4 nanoparticles manifested in exceptional EMI shielding, well above required shielding effectiveness value for most of the commercial applications, essentially through absorption. Taken together, the finding suggests that immiscible blends containing MWNTs and the decoration of magnetic nanoparticles (rGO-Fe3O4) on the surface of reduced graphene oxide sheets can be utilized to engineer high-performance EMI shielding materials with exceptional absorption ability.

The search and research for high performance materials for aerospace applications is a continuous evolving process. Among several fibre reinforced polymers, carbon fibre reinforced polymer (CFRP) is well known for its high specific stiffness and strength. Though high modulus and high strength carbon fibre with structural resin systems have currently been established reasonably well and are catering to a wide variety of aerospace structural applications, these properties are generally directional with very high properties along the fibre direction dominated by fibres and low in other directions depending mainly on the resin properties. Thus, there is a need to enhance the mechanical properties of the resin systems for better load transfer and to improve the resin dominated properties like shear strength and properties in directions other than along the fibre. Use of carbon nanotubes (CNTs) with their extraordinary specific stiffness and strength apparently has great potential as an additional reinforcement in resin for development of CNT-CFRP nanocomposites. However, there are several issues that need to be addressed such as compatibility of a particular resin with CNTs, amount of CNTs that can be added, uniform dispersion of these nanotubes, surface treatment and curing process etc., for optimal enhancement of the required properties. Epoxy and cyanate ester resin systems are finding applications in aerospace structures owing to their desirable set of properties. Of these, bisphenol E cyanate ester (BECy) resin of low viscosity with its low moisture absorption, better dimensional stability, and superior mechanical properties can establish itself as potential structural resin system for these applications. BECy in particular has the advantage of being more suitable for out of autoclave manufacturing process such as Vacuum Assisted Resin Transfer Molding (VARTM). Literature shows that, significant work has been carried out by various researchers reporting improvements using CNTs in epoxy resins along with various associated problems. However, studies on effects of addition of CNTs /fCNTs to BECy-CFRP composite system are not well reported. Thus, objective of this work is to study the effects of adding pristine and functionalized CNTs to low viscosity cyanate ester as well as epoxy resin systems. Further, to study the effects on mechanical properties of nanocomposites with carbon fibre reinforcement in these CNT dispersed resin system through a combination of experimental and computational approaches. Multiwall carbon nanotubes (CNTs) without and with different chemical functionalization are chosen to be added to epoxy and BECy resins. The quantity of these CNTs /fCNTs is varied in steps up to 1% by weight. Different methods of mixing such as shear mixing, ultrasonication and combined mixing cycles are implemented to achieve uniform dispersion of these nanotubes in the resin system. Standard test samples are prepared from these mixtures of nanotubes in resin systems to study the variation in mechanical properties. Further, these nanotubes added resin systems are used in fabricating CFRP laminates by VARTM process. Both uni-directional and bi-directional laminates are made with the above modified resin systems with CNTs/fCNTs. Series of experimental investigations are carried out to study various aspects involved in making of nanocomposites and the effects of the same on different mechanical properties of the nanocomposites. Standard specimens are cut out from these laminates to evaluate them for tension, compression, flexure, shear and interlaminar shear strength. The main parameters investigated are the effects of varied quantity of CNTs and functionalized CNTs in the resin mix and in CFRP nanocomposites, effect of different mixing / curing cycles etc. on the mechanical properties of the nanocomposites. The investigations have yielded very interesting and encouraging results to arrive at optimum quantity of CNTs to be added and also the effects of functionalization to achieve enhanced mechanical properties. In addition, correlation of mechanical property enhancements with failure mechanisms, dispersion behaviour and participation of CNTs / fCNTs in load transfer are explained with the aid of scanning electron microscope images. Computational studies are carried out through atomistic models using computational tools to estimate the mechanical properties, understand and validate the effects of various parameters studied through series of experimental investigations. An atomistic model is built taking into consideration the nanoscale effects of the single wall carbon nanotubes (SWCNTs) and its reinforcement in the BECy resin. Using these atomistic models, mechanical properties of individual SWCNT, BECy polymer resin, polymer with different quantities of added SWCNT, and the CFRP laminates with improved resin are computed. As the interaction of CNT with the polymer is only at the outermost layer and the mechanical properties of either MWCNTs or SWCNTs are too high compared to resin systems, it is not expected to have any difference in the final outcome whether it is MWCNT or SWCNT. Hence, only SWCNTs are considered in computational studies as it helps in reducing the complexity of atomistic models and computational time when coupled with polymer resin. This is valid even for functionalized CNT as functionalization is also a surface phenomenon. To start with, the mechanical behaviour of SWCNT is studied using molecular mechanics approach. Molecular mechanics based finite element analysis is adopted to evaluate the mechanical properties of armchair, zigzag and chiral SWCNT of different diameters. Three different types of atomic bonds, i.e., carbon-carbon covalent bond and two types of carbon-carbon van der Waals bonds are considered in the carbon nanotube system. The stiffness values of these bonds are calculated using the molecular potentials, namely Morse potential function and Lennard-Jones interaction potential function respectively and these stiffness values are assigned to spring elements in the finite element model of the SWCNT. The importance of inclusion of Lennard-Jones interactions is highlighted in this study. Effect of these non-bonded interactions is studied by making the numerical stiffness of these bonds to negligible levels and found that they significantly reduce the mechanical properties. The effect of non-bonded Lennard-Jones atomic interactions (van der Waal interactions) considered here is a novelty in this work which has not been considered in previous research works. The finite element model of the SWCNT is constructed, appropriate boundary conditions are applied and the behaviour of mechanical properties of SWCNT is studied. It is found that the longitudinal tensile strength and maximum tensile strain of armchair SWCNTs is greater than that of zigzag and chiral SWCNTs and its value increases with increasing SWCNT diameter. The estimated values of the mechanical properties obtained agree well with the published literature data determined using other techniques. As the systems become more complicated with the inclusion of polymers, molecular dynamics (MD) method using well established codes is more adoptable to study the effect of SWCNTs on BECy. Hence, it is used to model and solve the nanosystems to generate their stress-strain behavior. Further, MD approach followed here can effectively include interfacial interaction between polymer and the CNTs as well. Mechanical properties of SWCNT functionalized SWCNT (fSWCNT), pure BECy resin and that of the CNT nanocomposite consisting of specific quantity of SWCNT / fSWCNT in BECy are estimated using MD method. Atomistic models of SWCNT, fSWCNT, BECy, BECy with specific quantities of CNT / fSWCNT are constructed. A monomer of BECy is modelled and stabilized before its usage as a building block for modelling of BECy resin and to compute its properties. A cell of specific size containing monomers of BECy and another cell of same size with SWCNT at centre surrounded by BECy monomer molecules are built. The appropriate quantity of SWCNT in resin is modelled. This model captures the required density of the composite resin. The models so constructed are subjected to geometric optimization satisfying the convergence criteria and equilibrated through molecular dynamics to obtain a stable structure. The minimized structure is subjected to small strain in different directions to calculate the Young’s modulus and other moduli of the CNT-BECy resin composite. The process is repeated for different quantities of SWCNT in BECy resin to obtain their moduli. Further, tensile and shear strengths of CNT-BECy are obtained by subjecting the equilibrated structure to a series of applied strains from 0 to 10% in steps of 1%. The stress values corresponding to each strain are obtained and a stress – strain curve is plotted. From the stress- strain curve, the strengths of the CNT -BECy which is the stress corresponding to the modulus after which the material starts to soften are determined. Effects of functionalization on mechanical properties of SWCNT are observed. Further, effects of functionalization of SWCNT are studied with a specific quantity of fSWCNT on different moduli and strengths of BECy are investigated. The properties of enhanced CNT–BECy nanocomposite resin with different quantities of added CNT obtained through MD are used to estimate the mechanical properties of the CNT-BECy-CFRP nanocomposite using micromechanics model. Further, validation with experimental results is attempted comparing the trends in enhancement of properties of the CNT-BECy resin and CNT-BECy-CFRP nanocomposite system. The outcome of this research work has been significantly positive in terms of i) Development of an appropriate process establishing different parameters for dispersing CNTs in the resin system, mixing, curing cycle for making of nanocomposites demonstrating significant and consistent enhancement of mechanical properties of BECy based resin system and CFRP nanocomposites using optimum quantity of CNTs /fCNTs through a series of well planned and executed experimental investigations. Evaluation of mechanical properties for each of the cases has been carried out experimentally. ii) Establishing a computational methodology involving intricate atomistic modelling and molecular dynamics of nanosystems for estimation of mechanical properties of BECy polymer resin and to study the effects by addition of SWCNT / functionalized SWCNT on the properties. Results obtained through series of experimental investigations have been validated through this computational study. This could be an important step towards realising the potential of this resin system for high performance aerospace applications. Thus, in brief, detailed experimental work combined with computational studies performed as presented in this thesis resulted in achieving structurally efficient cyanate ester based nanocomposites which is unique and not reported in open literature.