Nanostructured thin films deposited by magnetron sputtering and gas aggregation sources of nanoparticles are studied especially with regards to their use in biomedical applications. The possibility of using plasma polymers for the preparation of antibacterial coatings is tested first. It is presented that sputtered nylon 6,6 films may be impregnated by antibiotics. The subsequent release of antibiotics from such prepared reservoirs may be tuned by their thickness, chemical composition, or by an additional barrier layer. The second studied type of antibacterial coatings is based on metallic nanoparticles overcoated with sputtered PTFE. It is shown that by a proper choice of the number of nanoparticles and thickness of fluorocarbon overlayer, a significant antibacterial effect can be achieved while maintaining the biocompatibility of produced nanocomposite coatings. The possibility to enhance the antibacterial effect by impregnation of plasma polymer/nanoparticle nanocomposites by antibiotics is also verified. Nanoparticle sources are used to study two-component films with 2D gradient character, too. A simple analytical model is developed allowing description and design of such nanomaterials. Its suitability is experimentally verified on 2D gradients combining Ag and Cu nanoparticles. Finally, an original...

Le but de cette étude est d’exploiter les fonctionnalités des nano-Composites Polymères Conducteurs (CPC) imprimés en utilisant la technologie FDM (modélisation par dépôt de monofilament en fusion) pour le développement de textiles fonctionnels et intelligents. L’impression 3D présente un fort potentiel pour la création d’une nouvelle classe de nanocomposites multifonctionnels. Par conséquent, le développement et la caractérisation des polymères et nanocomposites fonctionnels et imprimables en 3D sont nécessaires afin d’utiliser l’impression 3D comme nouveau procédé de dépôt de ces matériaux sur textiles. Cette technique introduira des procédés de fonctionnalisation de textiles plus flexibles, économes en ressources et très rentables, par rapport aux procédés d'impression conventionnels tels que la sérigraphie et le jet d'encre. L’objectif est de développer une méthode de production intégrée et sur mesure pour des textiles intelligents et fonctionnels, afin d’éviter toute utilisation d'eau, d'énergie et de produits chimiques inutiles et de minimiser les déchets dans le but d’améliorer l'empreinte écologique et la productivité. La contribution apportée par cette thèse consiste en la création et la caractérisation de filaments CPC imprimables en 3D, le dépôt de polymères et de nanocomposites sur des tissus et l’étude des performances en termes de fonctionnalité des couches de CPC imprimées en 3D. Dans un premier temps, nous avons créé des filaments de CPC imprimables en 3D, notamment des nanotubes de carbone à parois multiples (MWNT) et du noir de carbone à haute structure (Ketjenblack) (KB), incorporés dans de l'acide polylactique (PLA) à l'aide d'un procédé de mélange à l'état fondu. Les propriétés morphologiques, électriques, thermiques et mécaniques des filaments et des couches imprimées en 3D ont été étudiées. Deuxièmement, nous avons déposé les polymères et les nanocomposites sur des tissus à l’aide d’une impression 3D et étudié leur adhérence aux tissus. Enfin, les performances des couches de CPC imprimées en 3D ont été analysées sous tension et force de compression appliquées. La variation de la valeur de la résistance correspondant à la charge appliquée permet d’évaluer l'efficacité des couches imprimées en tant que capteur de pression / force. Les résultats ont montré que les nanocomposites à base de PLA, y compris MWNT et KB, sont imprimables en 3D. Les modifications des propriétés morphologiques, électriques, thermiques et mécaniques des nanocomposites avant et après l’impression 3D nous permettent de mieux comprendre l’optimisation du procédé. De plus, différentes variables du procédé d’impression 3D ont un effet significatif sur la force d'adhérence des polymères et des nanocomposites déposés sur les tissus. Nous avons également développé des modèles statistiques fiables associés à ces résultats valables uniquement pour le polymère et le tissu de l’étude. Enfin, les résultats démontrent que les mélanges PLA/MWNT et PLA/KB sont de bonnes matières premières piézorésistives pour l’impression 3D. Elles peuvent être potentiellement utilisées dans l’électronique portable, la robotique molle et la fabrication de prothèses, où une conception complexe, multidirectionnelle et personnalisable est nécessaire. / The aim of this study is to get the benefit of functionalities of fused deposition modeling (FDM) 3D printed conductive polymer nanocomposites (CPC) for the development of functional and smart textiles. 3D printing holds strong potential for the formation of a new class of multifunctional nanocomposites. Therefore, development and characterization of 3D printable functional polymers and nanocomposites are needed to apply 3D printing as a novel process for the deposition of functional materials on fabrics. This method will introduce more flexible, resource-efficient and cost-effective textile functionalization processes than conventional printing process like screen and inkjet printing. The goal is to develop an integrated or tailored production process for smart and functional textiles which avoid unnecessary use of water, energy, chemicals and minimize the waste to improve ecological footprint and productivity. The contribution of this thesis is the creation and characterization of 3D printable CPC filaments, deposition of polymers and nanocomposites on fabrics, and investigation of the performance of the 3D printed CPC layers in terms of functionality. Firstly, the 3D printable CPC filaments were created including multi-walled carbon nanotubes (MWNT) and high-structured carbon black (Ketjenblack) (KB) incorporated into a biobased polymer, polylactic acid (PLA), using a melt mixing process. The morphological, electrical, thermal and mechanical properties of the 3D printer filaments and 3D printed layers were investigated. Secondly, the performance of the 3D printed CPC layers was analyzed under applied tension and compression force. The response for the corresponding resistance change versus applied load was characterized to investigate the performance of the printed layers in terms of functionality. Lastly, the polymers and nanocomposites were deposited on fabrics using 3D printing and the adhesion of the deposited layers onto the fabrics were investigated. The results showed that PLA-based nanocomposites including MWNT and KB are 3D printable. The changes in morphological, electrical, thermal, and mechanical properties of nanocomposites before and after 3D printing give us a great understanding of the process optimization. Moreover, the results demonstrate PLA/MWNT and PLA/KB as a good piezoresistive feedstock for 3D printing with potential applications in wearable electronics, soft robotics, and prosthetics, where complex design, multi-directionality, and customizability are demanded. Finally, different variables of the 3D printing process showed a significant effect on adhesion force of deposited polymers and nanocomposites onto fabrics which has been presented by the best-fitted model for the specific polymer and fabric.

Solvent suspensions of a high performance polymer, Polyamide-imide (PAI) are widely used in magnetic wire coatings. Here we investigate the effect that the introduction of montmorillonite (MMT) has on PAI. MMT was introduced into an uncured PAI suspension; the sample was then cured by step-wise heat treatment. Polarized optical microscopy was used to choose the best suitable MMT for PAI matrix and to study the distribution of MMT in PAI matrix. Concentration dependent dispersion effect was studied by x-ray diffraction (XRD) and was confirmed by Transmission electron microscopy (TEM). Differential scanning Calorimetry (DSC) and Thermogravimetric analysis (TGA) was used to study impact of MMT on glass transition temperature (Tg) and degradation properties of PAI respectively. Micro-hardness testing of PAI nanocomposites was also performed. A concentration dependent state of dispersion was obtained. The glass transition (Tg), degradation and mechanical properties were found to correlate to the state of dispersion.

Fatty acid intercalated layered double hydroxides were used as additives for Jojoba oil and polymer matrices. The first phase of the study was to intercalate carboxylic acids (C14 to C22). These were successfully intercalated into layered double hydroxides (LDHs), with the formula [Mg0.7Al0.3 (OH) 2](CO3)0. 15•0.5H2O. The one-pot synthesis consistently yielded a bilayer intercalated product for the range of acids employed. The intercalated anions had an orientation tilt angle of 55–63°, depending on the length of the fatty acid chain. However, there is an indication that the anion exchange process employed in this study is accompanied by probable dissolution and recrystallisation of the LDH. This is supported by the different growth habits and sizes of platelets observed through scanning electron microscopy (SEM). Moreover, the organo-LDH platelets were found to have varying MII/MIII compositions, ranging from 1.65 to 6, indicating that the one-pot synthesis yields an array of mixed metal hydroxides. Polymer composites, containing 5% and 10 wt.% of stearate intercalated layered double hydroxides (LDH-stearate) and neat layered double hydroxides (LDH-CO3), were prepared via melt-compounding to explore the use of LDHs as an additive. The stearate modified starting material was bilayer-intercalated clay. During melt compounding, excess stearates were released and the clay reverted to a monolayer-intercalated form. Comprehensive characterisation and study of the fatty acid-intercalated LDH showed that these organoclay hybrids exhibit thermotropic behaviour. This behaviour ultimately leads to the exudation of excess fatty acid. The exuded stearates were found to have lubricating and plasticising effects on the poly(ethylene-co-vinyl acetate) (EVA) and linear low density polyethylene (LLDPE) matrices. Strong hydrogen bond interactions between the chains of poly(ethyleneco- vinyl alcohol) (EVAL) and the clay platelet surfaces overwhelmed the lubrication effect and caused an increase in the melt viscosity of this matrix. The notched Charpy impact strength of this composite was almost double that of the neat polymer. It appears that this can be attributed to the ability of the highly dispersed and randomly oriented nanosized clay platelets to promote extensive internal microcavitation during impact loading. The creation of a large internal surface area provided the requisite energy dissipation mechanism. The study also considered fatty acid-intercalated LDH as an argillaceous mineral for potential use as a rheological additive in Jojoba oil. A minimum of 20 wt.% LDH in Jojoba oil formulation was found to be stable, i.e. it did not form separate layers on standing. The viscosity of the neat Jojoba oil demonstrated Newtonian behaviour, whereas the modified LDH/Jojoba oil formulation shear thinned, which is a typical non-Newtonian behaviour. Viscosity as a function of temperature showed complex rheological behaviour for the long chain fatty acids C16 to C22. The viscosity increase is assumed to be due to a combination of three events, which include the formation and changes of LDH microstructures within the oil, the loss of excess fatty acids into the oil matrix, and the formation of fatty acid crystal networks. Shear action also induced some delamination of the clay platelets. / Thesis (PhD(Eng))--University of Pretoria, 2012. / Chemical Engineering / unrestricted

In this dissertation, new ways for controlling the internal structures of a system of polymer composites, polymer blends, and hydrogel composites by means of external electric or magnetic fields are presented. The first part of this study addresses the development of an anisotropic phase-separated morphology in polymer blends by using electrically pre-oriented clay particles. It was observed that electrically pre-oriented montmorillonite clay particles in a homogenous single-phase blend lead to anisotropic phase-separated morphology of the blends, undergoing demixing upon temperature shift to a two-phase regime. The initial co-continuous microstructure developed into a coarsened and directionally organized phase-separated morphology parallel to the direction of oriented clay particles (applied AC electric field direction) over the annealing time. It was also found that the degree of clay orientation under AC electric field was linearly proportional to the degree of polymer-phase orientation. The temporal morphological evolution was thoroughly analyzed by electron microscopy and X-ray diffraction studies. The second part of the study covers anisotropic hydrogel nanocomposites developed by orienting magnetically sensitive nontronite clay minerals under the strong magnetic fields. Anisotropic hydrogel nanocomposites were formed by magnetic-field assisted orientation of nontronite clays suspended in a hydrogel precursor solution followed by a gelation process. The degree of orientation of nontronite minerals was quantitively characterized by birefringence and small-angle X-ray scattering. The resultant hydrogels exhibited anisotropic optical, mechanical, and swelling properties along the direction of oriented clay minerals. Anisotropic water swelling behaviors can be particularly applied in medical dressing materials, where vertical wicking of fluid into the wound dressing is sought after for minimizing periwound maceration damage.

Semicrystalline polymers constitute the majority of the commercially manufactured polymers, mostly known as commodities with low modulus and inferior properties. A robust approach used in tailoring such commodity’s properties for more advanced applications is through the incorporation of inorganic nanoparticles (NPs). Over the past half century, polymer nanocomposites (PNCs) have attracted extensive interest in fundamental research and technological applications. However, NPs have been found to result in complicated alterations in the semicrystalline polymer crystallization kinetics, and their crystalline morphology, which could either synergistically or adversely affect the final composite properties. A comprehensive understanding of this topic is still lacking, which with one could tune the final polymer properties for various cutting-edge applications. In this dissertation, we focus on the crystallization kinetics of semicrystalline PNCs and the connection between the morphology and the mechanical (and rheological) properties of such hybrid systems. First, we control the NP dispersion and self-assembly in a semicrystalline poly(ethylene oxide) (PEO) matrix using both bare and polymer-grafted NPs. We show that bare NPs (with different sizes) and unimodal poly(methyl methacrylate) (PMMA)-g-SiO2 NPs uniformly disperse in a PEO matrix because of the favorable interaction between the matrix and the NP surface (or the PMMA brush). Grafting the latter NPs with a short dense polystyrene brush that is immiscible with PEO while varying the PMMA grafting parameters induces self-assembly and leads to various NP structures: well-dispersed, connected sheets, strings, and large aggregates. Next, we systematically investigate the role of bare and self-assembled grafted NPs on the spherulitic growth kinetics of semicrystalline polymers. In all cases, the incorporation of spherical NPs suppresses the polymer growth kinetics. Using rheological measurements, we show that the reduction in growth is mainly attributed to the NPs increasing the melt viscosity; whereas, they minimally alter the secondary nucleation process. Surprisingly, the PNC growth kinetics is suppressed in two apparently universal manners when plotted as a function of confinement: NP dominated and brush-controlled regimes. Bare NPs and large aggregates of polymer-grafted NPs appear to nearly follow the same dependence for the role of additives on polymer viscosity, weakly suppressing the growth kinetics. On the other hand, all the other self-assembled NP structures showed much stronger growth reductions because of the larger increase in the melt viscosity by the chemically bonded brush. Given our prior knowledge of the PNC growth kinetics, we then draw generalized trends for the role of bare and grafted NPs in nucleating semicrystalline polymers. This is achieved by comparing the polymer crystallization kinetics in the presence of large, asymmetric, immobile fillers (selected from the well-established literature) to those smaller, spherical, mobile NPs (examined throughout this thesis). Generally, NPs serve as heterogenous nucleation sites when incorporated at smaller amounts, leading to accelerated crystallization kinetics. At larger filler contents, NPs confine the polymer chains into smaller domains and become more susceptible to aggregation, which results in antinucleating effects and suppressing the crystallization rate. Such competing effects result in a maximum nucleation efficiency at moderate filler contents. It is also worth noting that the degree of nucleation enhancement and subsequent suppression depends on the system and is controlled by NP dispersion, geometry, and surface chemistry. For example, one- and two-dimensional NPs usually result in a higher nucleation power compared to spherical NPs. Another major difference between mobile and immobile fillers is that when slowly crystallizing from the melt, the smaller diffusive NPs can be segregated and ordered into hierarchal structures (interlamellar sheets and interfibrillar and interspherulitic aggregates). This provides a much richer class of materials with a kinetics route in controlling NP assemblies. Finally, we create robustly toughened semicrystalline polymers by confining the PEO crystallization using a densely grafted PMMA brush (i.e., PMMA-g-SiO₂) with different molecular weights. For comparison, we prepare linear PMMA/PEO blends with equivalent PMMA molecular weights and volume fractions to those of the nanocomposites. We show that PMMA-g¬-SiO₂ NPs surpass linear PMMA homopolymers in terms of toughening the PEO matrix, with the grafted system experiencing relatively higher connectivity and lower crystallinity. At moderate confinement, the nanocomposite sustains a maximum modulus increase of 42%, with around a 200-fold increase in the PEO toughness. This provides a novel route for toughening semicrystalline polymers using noncrystallizable polymer-grafted NPs.

Polymer nanocomposites (PNCs) have found their way into our everyday lives in a long list of applications, including airplane parts and car tires. This is due to their unique properties of combining the strengths of their constituents – elasticity and stiffness – while mitigating their weaknesses – softness and brittleness. In the past few decades, they have generated more interest due to the discovery that the PNCs’ optical, electrical, and a host of other properties can be tuned for specific use by controlling the assembly and dispersion of nanoparticles (NPs) within the host polymer matrix. The grafting of some of the matrix chains onto the surface of the NPs not only improves NP miscibility but also grants an additional handle tocontrol the self-assembly of NPs. However, at present, there remains many open questions in the field of these novel PNCs. For instance, it is commonly believed that long enough matrix polymers of length P will spontaneously dewet a chemically identical polymer layer, comprised of sufficient chains of length N , end-grafted to a flat surface (”brush”). This entropically driven idea is frequently used to explain experiments in which 10-20 nm diameter polymer-grafted NPs are observed to phase separate from homopolymer matrices for P/N⪆4. At lower grafting densities, these entropic effects are also thought to underpin the self-assembly of grafted NPs into a diverse set of structures. To explore the validity of this picture, a two-pronged approach is used in this thesis, exploring such systems from both a single NP and a multi-NP point of view in order to find novel methods for understanding and controlling NP dispersion in polymers. In each of the chapters, we employ coarse-grained Molecular Dynamics (MD) simulations to understand the self-assembly and dispersion behavior in PNCs, with the experimental analog being primarily polystyrene (PS) grafted silica NPs in PS matrices. We start by investigating the entropic effects of P/N on the brush of a single grafted NP, taking advantage of an indirect umbrella sampling method (INDUS) to quantify matrix density fluctuations. This method essentially makes use of an external biasing potential to mimic the dewetting of the brush. We find for the first time that entropic P/N effects can be identified at the single NP level and is primarily surface driven. INDUS is later extended to two-body and many-body NP systems, to understand the role of NP surfactantcy in the self-assembly of grafted NPs and create free-energy profiles for a range of inter-NP separations. Finally, results from a comprehensive series of large-scale multi-NP simulations, where we consider NPs in the ≈ 5nm and ≈ 10nm size range. For the smaller NPs, we find no evidence of phase separation even for P/N = 10 in the absence of attractions. Instead, we discover that we are able to recreate most of the experimentally observed structures when allthe polymer chain monomers are equally attractive to each other but repel the NPs. Only when the NPs are in the ≈ 10nm size range that we are able to access the phase separated morphologies. Our results thus imply that experimental situations where the grafting density is low are dominated by the surfactancy of the NPs, which is driven by the chemical mismatch between the inorganic core and the organic ligands (the graft and free chains are chemically identical). Entropic effects, i.e. the translational entropy of the NPs and the matrix, the entropy of mixing of the grafts and the matrix, and the conformational entropy of the chains appear to thus play a second order effect even in the context of these model systems. Each of these insights provides details around controlling the organization and assembly of NPs in polymers for the purpose of improving their mechanical properties, all while changing the way in which the material is designed.

Silicon nanocrystals (SiNCs) are nanometer-sized semiconducting materials. Their small size endows them with unique photophysical properties. Efficient photoluminescence (PL) from silicon nanocrystal (SiNC) composites has important implications for emerging solar-energy collection technologies, yet a detailed understanding of PL relaxation in non-colloidal SiNCs is still materializing. In this dissertation, we examine the photophysical properties of silicon nanocrystal/off-stoichiometry thiol-ene composites (SiNCs/OSTE hybrids). The dissertation begins with an introduction to the photophysical properties of SiNCs, their photophysical properties, how SiNC/polymer composites are made, the various SiNC preparation techniques, and the most likely application areas for these nanocrystals. A description of experimental methods such as PL spectroscopy and transmission electron microscopy (TEM) follows, and SiNC/OSTE polymer preparation methods are then explained in detail. In the first study, TEM and photophysical characterization were performed on selected polydisperse SiNCs samples. These samples were synthesized in a nonthermal plasma reactor, using Si6H12 as precursor, and functionalized with R (where R is 1-dodecene). These SiNCs were dispersed in mesitylene:1-dodecene (5:1) as a colloid. Optical absorption, quantum efficiency, and PL lifetime of SiNCs were then investigated, as well as the relationship between quantum yield, lifetime, and PL peak. In the second study, we selected samples for size separation via the density gradient ultracentrifugation method (DGU). We successfully applied this technique to separate silicon nanocrystals with sizes from 2 nm to 4 nm from the ensemble samples using an engineered density medium layer stack, and photophysical characterization was performed on the DGU size–separated SiNCs. Lastly, we explored details of PL relaxation in photo-polymerized off-stoichiometric polymer/nanocrystal hybrids. We found time- and air-stable emission from dilute composites with up to 70% QY, and we investigated PL relaxation in the parameter space of nanocrystal size and temperature. In light of previous work, our results reveal similarities between the impacts of crosslinking and cooling to cryogenic temperature, but of which are characterized by a relative reduction in the available of phonons.

Silica nanoparticles (SiO2 NPs) were prepared and functionalized with polyethylene (PE@SiO2 NPs) using the surface-initiated polyhomologation (SI polyhomologation) technique. Polyolefin nanocomposites were fabricated later by melt mixing of different ratios of the as-prepared SiO2 NPs and PE@SiO2 NPs with linear low-density polyethylene (LLDPE) and low-density polyethylene (LDPE) matrices. Firstly, SiO2 NPs were modified with different alkoxysilane ligands, dichloro(divinyl)silane (DCDVS), allyl trimethoxysilane (ATMS), and vinyl triethoxylsilane (VTES). Subsequently, thexylborane, an initiator for SI polyhomologation, was immobilized to the modified surface of SiO2 NPs through hydroboration reactions. Polyhomologation was then allowed to proceed by adding monomer solution to form polyethylene brushes covalently bonded to the surface of the NPs. Physicochemical characterization had confirmed the morphology, chemical structure, and thermal stability for each step of modification reactions. LLDPE and LDPE nanocomposites were prepared by extrusion with SiO2 NPs and PE@SiO2 NPs as nanofillers. Finally, tensile tests and morphological SEM-based analyses are presented to discuss the influence of the grafted PE on both the dispersion of the fillers and the mechanical properties of the filler/matrix interphase.

A dissertation submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, in fulfilment of the requirements for the degree of Master of Science in Engineering. Johannesburg, 21 July 2016 / The use of supercapacitors for energy storage is an attractive approach considering their ability to deliver high levels of electrical power, unlimited charge/discharge cycles, green environmental protection and long operating lifetimes. Despite the satisfactory power density, supercapacitors are yet to match the energy densities of batteries and fuel cells, reducing the competitiveness as a revolutionary energy storage device. Therefore, the biggest challenge for supercapacitors is the trade-off between energy density and power density. This presents an opportunity to enhance the electrochemical capacitance and mechanical stability of an electrode. Previous attempts to get around the problem include developing porous nanostructured electrodes with extremely large effective areas. One of the emerging high-power supercapacitor electrode materials is molybdenum disulfide (MoS2), a member of the transition-metal dichalcogenides (TMDs). Its higher intrinsic fast ionic conductivity and higher theoretical capacity have attracted a lot of attention, particularly in supercapacitors. In addition to double-layer capacitance, diffusion of the ions into the MoS2 at slow scan rates gives rise to Faradaic capacitance. Analogous to Ru in RuO2, the Mo center atom displays a range of oxidation states from +2 to +6. This plays an important role in enhancing charge storage capabilities. However, the electronic conductivity of MoS2 is still lower compared to graphite, and the specific capacitance of MoS2 is still very limited when used alone for energy storage applications. As evident in several literature reports, there is a need to improve the capacitance of MoS2 with conductive materials such as carbon nanotubes (CNT), polyaniline (PANI), polypyrrole (PPy), and reduced graphene (r-GO). Carbon nanospheres (CNS) have, in the past, improved the conductivity of cathode material in Li-ion batteries, owing to their appealing electrical properties, chemical stability and high surface area. The main objective of this dissertation research is to develop nanocomposite materials based on molybdenum sulphide with carbon nanospheres for pseudocapacitors with simultaneously high power density and energy density at low production cost. The research was carried out in two phases, namely, (i) Symmetric pseudocapacitors based on molybdenum disulfide (MoS2)-modified carbon nanospheres: Correlating physico-chemistry and synergistic interaction on energy storage and (ii) The effects of morphology re-arrangements on the pseudocapacitive properties of mesoporous molybdenum disulfide (MoS2) nanoflakes. The physico-chemical properties of the MoS2 layered materials have been interrogated using the surface area analysis (BET), scanning electron microscopy (SEM), transmission electron microscopy (TEM), x-ray diffraction (XRD), Raman, fourier-transform infrared (FTIR) spectroscopy, and advanced electrochemistry including cyclic voltammetry (CV), galvanostatic cycling with potential limitation (GCPL), repetitive electrochemical cycling tests, and electrochemical impedance spectroscopy (EIS). In the first phase, Molybdenum disulfide-modified carbon nanospheres (MoS2/CNS) with two different morphologies (spherical and flower-like) have been synthesized using hydrothermal techniques and investigated as symmetric pseudocapacitors in aqueous electrolyte. The two different MoS2/CNS layered materials exhibit unique differences in morphology, surface areas, and structural parameters, which have been correlated with their electrochemical capacitive properties. The flower-like morphology (f-MoS2/CNS) shows lattice expansion (XRD), large surface area (BET analysis), and small-sized nanostructures (corroborated by the larger FWHM of the Raman and XRD data). As a contrast to the f-MoS2/CNS, the spherical morphology (s-MoS2/CNS) shows lattice contraction, small surface area with relatively large-sized nanostructures. The presence of CNS on the MoS2 structure leads to slight softening of the characteristic Raman bands (E12g and A1g modes) with larger FWHM. The MoS2 and its CNS-based composites have been tested in symmetric electrochemical capacitors in aqueous 1 M Na2SO4 solution. CNS improves the conductivity of the MoS2 and synergistically enhanced the electrochemical capacitive properties of the materials, especially the f-MoS2/CNS-based symmetric cells (most notably, in terms of capacitance retention). The maximum specific capacitance for f-MoS2/CNS-based pseudocapacitor show a maximum capacitance of 231 F g-1 with high energy density 26 Wh kg-1 and power density 6443 W kg-1. For the s-MoS2/CNS-based pseudocapcitor, the equivalent values are 108 F g-1, 7.4 Wh kg-1 and 3700 W kg-1. The high-performance of the f-MoS2/CNS is consistent with its physico-chemical properties as determined by the spectroscopic and microscopic data. In the second phase, Mesoporous molybdenum disulfide (MoS2) with different morphologies has been prepared via a hydrothermal method using different solvents, water or water/acetone mixtures. The MoS2 obtained with water alone gave graphene-like nanoflakes (g-MoS2) while the other with water/acetone (1:1 ratio) gave a hollow-like morphology (h-MoS2). Both materials are modified with carbon nanospheres as conductive materials and investigated as symmetric pseudocapacitors in aqueous electrolyte (1 M Na2SO4 solution). Interestingly, a simple change of synthesis solvents confers on the MoS2 materials different morphologies, surface areas, and structural parameters, correlated by electrochemical capacitive properties. The g-MoS2 exhibits higher surface area, higher capacitance parameters (specific capacitance of 183 F g-1, maximum energy density of 9.2 Wh kg-1 and power density of 2.9 kW kg-1) but less stable electrochemical cycling compared to the h-MoS2. These findings have opened doors for further exploration of the synergistic effects between MoS2 graphene-like sheets and CNS for energy storage. / MT2017