No description available.

Thesis (PhD) - Swinburne University of Technology, Faculty of Engineering and Industrial Sciences, Centre for Atom Physics an Ultra-fast Spectroscopy, 2008. / A thesis submitted for the degree of Master of Engineering, Centre for Atom Physics an Ultra-fast Spectroscopy, Faculty of Engineering and Industrial Sciences, Swinburne University of Technology, 2008. Typescript. Bibliography: p. 143-149.

Thesis (M.S.)--Virginia Polytechnic Institute and State University, 1994. / Vita. Abstract. Includes bibliographical references (leaves 64-66). Also available via the Internet.

D.Phil. / This dissertation deals with the fabrication, characterisation, and applications of long-period gratings in optical fibre communications and sensing systems. The aim of this project is to assess long-period gratings as media for active or passive fibre devices, particularly as components for the telecommunications industry. A review of the properties and characteristics of fibre gratings associated with the photosensitivity of germanosilicate fibres is provided, which includes a theoretical analysis of the principles of operation for short-period gratings (fibre Bragg gratings) and long-period gratings. The simulations of the spectral response from these two types of gratings are also presented. A number of long-period grating fabrication methods and techniques, which were reported by some researchers, are reviewed. In this project, the normal long-period gratings and phase-shifted long-period gratings are fabricated by using a line-narrowed KrF excimer laser combined with the metal amplitude mask technique. The metal mask is made of a stainless steel sheet, and the slot width (periodicity) is processed by using high quality photographic tooling. Three normal long-period gratings with different periodicities and one phase-shifted long-period grating can be manufactured simultaneously because there are four metal masks imprinted in one inexpensive stainless steel sheet. The mass-production of long-period gratings becomes possible, and the number of gratings that can be written is limited only by the excimer laser beam or metal mask dimension orthogonal to the fibre axis. The fibres that are used in our experiments are photosensitive optical fibres (PS1500). Long-period gratings can be written directly into these fibres without hydrogenation. Two types of long-period grating devices are investigated and developed for applications in dense wavelength division multiplexing (DWDM)networks: erbium-doped fibre amplifier (EDFA) gain-flattening filters and wavelength-tuneable add/drop multiplexers. Firstly, the transmission characteristics of phase-shifted long-period gratings are simulated theoretically by a combination of the coupled-mode theory and the fundamental-matrix method. It is suggested that a phase-shifted long-period grating device cascaded with another normal long-period grating can be used to flatten the gain spectrum of an EDFA containing three gain peaks. The experimental results show that a broad amplifier with peak-to-peak variations of less than 0.7 dB over 36 nm from 1526 to 1562 nm, which covers the entire C-band of the EDFA, can be realized practically. Next, a wavelength-tuneable add/drop multiplexer is designed and configured. In this device, four identical long-period gratings are assembled on piezoelectric ceramic fibre stretchers. The modelling of the device predicts that 50 ITU DWDM-channel signals could be selected in the wavelength range from 1526.25 to 1563.75 nm with 0.75 nm channel spacing and the cross-talk is less than –39 dB while the total insertion loss is about 0.24 dB. There are some significant advantages of wavelength-tuneable add/drop multiplexing devices over conventional fibre Bragg grating-based devices. (1) There is back reflected light and almost no cross-talk power penalty because the long-period grating couples light into forward-propagating modes. (2) Signal channel isolation is very high due to three stages of coupling mechanisms used in this device, which includes core-cladding, cladding-cladding and cladding-core, efficiently filtering out non-resonant light. (3) The insertion loss of the device is limited only by the separation of two long-period gratings, because there are no losses on non-resonant wavelengths of long-period gratings. Several other applications of long-period gratings in optical sensing systems are also described, and some are experimented on including axial strain sensors, structural bend sensors, temperature sensors, refractive index sensors and chemical concentration sensors.

D.Ing. / Most optical fibre-based ambient refractive index sensors (including individual long-period gratings) rely on spectral attributes obtained in transmission. However, a probe refractometer has been proposed that is based on self-interference of a long-period grating (LPG), thus providing reflectance spectra containing the relevant data. This sensor operates as a Michelson interferometer by virtue of the fact that its constituent LPG acts as both a mode converter and coupler. Its construction is such that optical power coupled into the cladding (when light impinges on the LPG) is reflected at a fibre mirror and returns towards the grating, where it is re-coupled into the fundamental guided mode. Since light waves propagating along the core and cladding material of the fibre cavity beyond the LPG experience different optical path lengths (due to differing mode indices), a phase difference exists between these modes upon recombining at the grating location. This causes interference, which is manifested as a characteristic fringe pattern in the sensor’s reflectance spectrum (analogous to that obtained in the transmission of a twin LPG cascade operating as a Mach-Zehnder interferometer). Research was conducted towards implementing a unique method of temperature compensation in this LPG-based Michelson interferometer. Sensing attributes of individual LPGs were investigated first, with specific emphasis on the temperature characteristics of two different types of host fibre. It was found that LPGs manufactured in conventional ATC SMF-28 fibre (previously hydrogen-loaded to inscribe the grating and annealed after fabrication) and B/Ge co-doped PS1500 fibre from Fibercore exhibited temperature characteristics of opposite polarity. This led to the implementation of a compound-cavity Michelson interferometer whose constituent LPG is written in one type of fibre, while a specific length of the other type of fibre is fusion spliced onto the host fibre section. Experiments verified the success of this temperature-compensation technique, which caused a measured reduction in temperature sensitivity of up to in interferometer phase shift. Measurements of the refractive index of the test substance surrounding the cladding material of the Michelson interferometer’s fibre cavity (and not the LPG itself) could therefore be done without being adversely affected by environmental temperature fluctuations. This was demonstrated experimentally by comparing the interferometer’s phase shift – devoid of temperature-induced effects – due to increasing refractive index of the analyte (as a result of escalating temperature) with index of refraction readings from a temperature-controlled Abbe refractometer. Numerical gradients of linear curves fitted to these results differed by two orders of magnitude less than the resolution of readings obtained from an Abbe refractometer – proof of the success of the temperature compensation technique applied in this LPG-based Michelson refractometer.

Analogcircuit/IC design for high speed optical fiber communication is a fairly new research area in Dr. Ha's group. In the first project sponsored by ETRI (Electronics and Telecommunication Research Institute) we started to design the building blocks of receiver for next generation 400 Gb/s optical fiber communication. In this thesis research a transceiver architecture based on 4x100 Gb/s parallel communication is proposed. As part of the receiver, a transimpedance amplifier for 100 Gb/s optical communication is designed, analyzed and simulated. Simulation results demonstrate the excellent feasibility of proposed architecture. Bipolar technology based on III-V materials (e.g. - GaAs, InP based HBT, HEMT) has always dominated the high speed optical transceiver design because of their inherent properties of high mobility and low noise. But they are power hungry and bulky in size which made them less attractive for highly integrated circuit design. On the contrary, CMOS technology always drew attraction because of low cost, low power dissipation and high level of integration facility. But their notorious parasitic characteristic and inferior noise performance makes high speed transceiver design very challenging. The emergence of nano-scale CMOS offer highly scaled feature sized transistors with transition frequencies exceeding 200 GHz and can improve optical receiver performance significantly. Increasing bandwidth to meet the target data rate is the most challenging task of TIA design especially in CMOS technology. Several CMOS TIA architectures have been published recently [6]-[11] for 40 Gb/s data rate having bandwidth no more than 40 GHz. In contrast to existing works, the goal of this research is to step further and design a single channel stand-alone TIA compatible in serial 100 Gb/s data rate with enhanced bandwidth and optimized transimpedance gain, input referred noise and group delay variation. A 100 Gb/s transimpedance amplifier (TIA) for optical receiver front end is designed in this work. To achieve wide bandwidth and low group delay variation a differential TIA with active feedback network is proposed. Proposed design also combines regulated cascode front end, peaking inductors and capacitive degeneration to have wide band response. Simulation results show 70 GHz bandwidth, 42 dBΩ transimpedance gain and 2.8 ps of group delay variation for proposed architecture. Input referred noise current density is 26 pA/â while the total power dissipation from 1.2V supply is 24mW. Performance of the proposed TIA is compared with other existing TIAs, and the proposed TIA shows significant improvement in bandwidth and group delay variation compared to other existing TIA architectures. / Master of Science

A stable dual-wavelength Tm:Ho co-doped fiber laser operating above 2 mu m based on cascaded single mode-multimode-single mode (SMS) all-fiber structures has been proposed and experimentally demonstrated for the first time.

Thanks to their capability of transmitting light with low loss, optical fibers have found a wide range of applications in illumination, imaging, and telecommunication. However, since the light guided in a regular optical fiber is well confined in the core and effectively isolated from the environment, the fiber does not allow the interactions between the light and matters around it, which are critical for many sensing and actuation applications. Specially shaped optical fibers endow the guided light in optical fibers with the capability of interacting with the environment by modifying part of the fiber into a special shape, while still preserving the regular fiber’s benefit of low-loss light delivering. However, the existing specially shaped fibers have the following limitations: 1) limited light coupling efficiency between the regular optical fiber and the specially shaped optical fiber, 2) lack special shape designs that can facilitate the light-matter interactions, 3) inadequate material selections for different applications, 4) the existing fabrication setups for the specially shaped fibers have poor accessibility, repeatability, and controllability. The overall goal of this dissertation is to further the fundamental understanding of specially shaped fibers and to develop novel specially shaped fibers for different applications. In addition, the final part of this dissertation work proposed a microfluidic platform that can potentially improve the light-matter interactions of the specially shaped fibers in fluidic environments. The contributions of this dissertation work are summarized as follows: 1) An enhanced fiber tapering system for highly repeatable adiabatic tapered fiber fabrications. An enhanced fiber tapering system based on a novel heat source and an innovative monitoring method have been developed. The novel heat source is a low-cost ceramic housed electric furnace (CHEF). The innovative monitoring method is based on the frequency-domain optical transmission signal from the fiber that is being tapered. The enhanced fiber tapering system can allow highly repeatable fabrication of adiabatically tapered fibers. 2) A lossy mode resonance (LMR) sensor enabled by SnO2 coating on a novel specially shaped fiber design has been developed. The developed LMR sensor has a D-shape fiber tip with SnO2 coating. It has the capability of relative humidity and moisture sensing. The fiber-tip form factor can allow the sensor to be used like a probe and be inserted into/removed from a tight space. 3) Specially shaped tapered fibers with novel designs have been developed for integrated photonic and microfluidic applications. Two novel specially tapered fibers, the tapered fiber loop and the tapered fiber helix have been developed. The tapered fiber loop developed in this work has two superiority that differentiated itself from previous works: a) the mechanical stability of the tapered fiber loop in this work is significantly better. b) the tapered fiber loops in this work can achieve a diameter as small as 15 ?m while still have a high intrinsic optical quality factor of 32,500. The tapered fiber helix developed in this work has a 3D structure that allows it to efficiently deliver light to locations out of the plane defined by its two regular fiber arms. Applications of the tapered fiber helices in both integrated photonic device characterizations and microparticle manipulations have been demonstrated. 4) Developed an acrylic-tape hybrid microfluidic platform that can allow function reconfiguration and optical fiber integration. A low-cost, versatile microfluidic platform based on reconfigurable acrylic-tape hybrid microfluidic devices has been developed. To the best of the author’s knowledge, this is the first time that the fabrication method of sealing the acrylic channel with a reconfigurable functional tape has been demonstrated. The tape-sealing method is compatible with specially shaped fiber integrations.

Thanks to their capability of transmitting light with low loss, optical fibers have found a wide range of applications in illumination, imaging, and telecommunication. However, since the light guided in a regular optical fiber is well confined in the core and effectively isolated from the environment, the fiber does not allow the interactions between the light and matters around it, which are critical for many sensing and actuation applications. Specially shaped optical fibers endow the guided light in optical fibers with the capability of interacting with the environment by modifying part of the fiber into a special shape, while still preserving the regular fiber’s benefit of low-loss light delivering. However, the existing specially shaped fibers have the following limitations: 1) limited light coupling efficiency between the regular optical fiber and the specially shaped optical fiber, 2) lack special shape designs that can facilitate the light-matter interactions, 3) inadequate material selections for different applications, 4) the existing fabrication setups for the specially shaped fibers have poor accessibility, repeatability, and controllability. The overall goal of this dissertation is to further the fundamental understanding of specially shaped fibers and to develop novel specially shaped fibers for different applications. In addition, the final part of this dissertation work proposed a microfluidic platform that can potentially improve the light-matter interactions of the specially shaped fibers in fluidic environments. The contributions of this dissertation work are summarized as follows: 1) An enhanced fiber tapering system for highly repeatable adiabatic tapered fiber fabrications. An enhanced fiber tapering system based on a novel heat source and an innovative monitoring method have been developed. The novel heat source is a low-cost ceramic housed electric furnace (CHEF). The innovative monitoring method is based on the frequency-domain optical transmission signal from the fiber that is being tapered. The enhanced fiber tapering system can allow highly repeatable fabrication of adiabatically tapered fibers. 2) A lossy mode resonance (LMR) sensor enabled by SnO2 coating on a novel specially shaped fiber design has been developed. The developed LMR sensor has a D-shape fiber tip with SnO2 coating. It has the capability of relative humidity and moisture sensing. The fiber-tip form factor can allow the sensor to be used like a probe and be inserted into/removed from a tight space. 3) Specially shaped tapered fibers with novel designs have been developed for integrated photonic and microfluidic applications. Two novel specially tapered fibers, the tapered fiber loop and the tapered fiber helix have been developed. The tapered fiber loop developed in this work has two superiority that differentiated itself from previous works: a) the mechanical stability of the tapered fiber loop in this work is significantly better. b) the tapered fiber loops in this work can achieve a diameter as small as 15 ?m while still have a high intrinsic optical quality factor of 32,500. The tapered fiber helix developed in this work has a 3D structure that allows it to efficiently deliver light to locations out of the plane defined by its two regular fiber arms. Applications of the tapered fiber helices in both integrated photonic device characterizations and microparticle manipulations have been demonstrated. 4) Developed an acrylic-tape hybrid microfluidic platform that can allow function reconfiguration and optical fiber integration. A low-cost, versatile microfluidic platform based on reconfigurable acrylic-tape hybrid microfluidic devices has been developed. To the best of the author’s knowledge, this is the first time that the fabrication method of sealing the acrylic channel with a reconfigurable functional tape has been demonstrated. The tape-sealing method is compatible with specially shaped fiber integrations.

M.Ing. (Electrical and Electronic Engineering) / A distributed temperature fiber sensor based on the ratio of the Raman anti-Stokes to Rayleigh backscattered light components is studied. The aim of the study is to propose a method of quantifying the noise exhibited in the Rayleigh backscattered signal and further propose correlation coding techniques to reduce the noise in the Rayleigh and Raman backscattered signals. The noise in the Rayleigh backscattered signal is referred to as “interferometric noise”. When Rayleigh scattering along the length of an optical fiber occurs, some of the scattered light travels in a direction opposite to the direction of propagation, and is called backscattered light. When the coherence length of the optical source permits interactions between the Rayleigh backscattered light, there is a possibility for the interacting backscattered light, within a distance that is half the coherence length, to interfere with each other. Furthermore, when the sensing optical fiber is greater than the coherence length of the optical source, there will be several interference sections along the length of the sensing fiber causing the intensity of the Rayleigh backscattered light at the photo-detectors to vary randomly. The intensity variation gives the Rayleigh backscattered signal a jagged appearance indicating the presence of interferometric noise. The longer the coherence length of the optical sources, the larger the intensity variations in the backscattered light, that is, the more the interferometric noise exhibited. The more the interferometric noise in the Rayleigh backscattered signal, the poorer the temperature accuracy of the distributed temperature sensor based on the ratio of the Raman anti Stokes to Rayleigh backscattered components. To quantify the interferometric noise affecting the Rayleigh backscattered signal, a mathematical model based on well-known scattering and interferometry theories is developed. Using the developed mathematical noise model, noise powers of approximately -52dBm and -40dBm for coherence lengths of 4m and 24m are respectively obtained...