Analogcircuit/IC design for high speed optical fiber communication is a fairly new research area in Dr. Ha's group. In the first project sponsored by ETRI (Electronics and Telecommunication Research Institute) we started to design the building blocks of receiver for next generation 400 Gb/s optical fiber communication. In this thesis research a transceiver architecture based on 4x100 Gb/s parallel communication is proposed. As part of the receiver, a transimpedance amplifier for 100 Gb/s optical communication is designed, analyzed and simulated. Simulation results demonstrate the excellent feasibility of proposed architecture. Bipolar technology based on III-V materials (e.g. - GaAs, InP based HBT, HEMT) has always dominated the high speed optical transceiver design because of their inherent properties of high mobility and low noise. But they are power hungry and bulky in size which made them less attractive for highly integrated circuit design. On the contrary, CMOS technology always drew attraction because of low cost, low power dissipation and high level of integration facility. But their notorious parasitic characteristic and inferior noise performance makes high speed transceiver design very challenging. The emergence of nano-scale CMOS offer highly scaled feature sized transistors with transition frequencies exceeding 200 GHz and can improve optical receiver performance significantly. Increasing bandwidth to meet the target data rate is the most challenging task of TIA design especially in CMOS technology. Several CMOS TIA architectures have been published recently [6]-[11] for 40 Gb/s data rate having bandwidth no more than 40 GHz. In contrast to existing works, the goal of this research is to step further and design a single channel stand-alone TIA compatible in serial 100 Gb/s data rate with enhanced bandwidth and optimized transimpedance gain, input referred noise and group delay variation. A 100 Gb/s transimpedance amplifier (TIA) for optical receiver front end is designed in this work. To achieve wide bandwidth and low group delay variation a differential TIA with active feedback network is proposed. Proposed design also combines regulated cascode front end, peaking inductors and capacitive degeneration to have wide band response. Simulation results show 70 GHz bandwidth, 42 dBΩ transimpedance gain and 2.8 ps of group delay variation for proposed architecture. Input referred noise current density is 26 pA/â while the total power dissipation from 1.2V supply is 24mW. Performance of the proposed TIA is compared with other existing TIAs, and the proposed TIA shows significant improvement in bandwidth and group delay variation compared to other existing TIA architectures. / Master of Science

This paper is the use of the active inductor instead of passive inductors to save area, enter the match aspects of the use of the feedback capacitor in parallel with the resistor to achieve matching with the control input voltage, in addition to adjusting the feedback resistor can control the noise. The LNA dissipates 13.2 mW power and achieves input return loss (S11) below -10dB, output return loss (S22) below -10 dB, forward gain (S21) of 11.3~14.5dB, reverse isolation (S12) below -40dB, and noise figure (NF) of 3~3.18 dB. 1-dB compression point (P1dB) of -24 dBm and input third-order inter-modulation point (IIP3) of -14 dBm .

This master thesis describes the design of a track-and-hold (T&H) circuit with 10bit resolution, 80MS/s and 30MHz bandwidth. It is designed in a 0.18µm CMOS process with a supply voltage of 1.8 Volt. The circuit is supposed to work together with a 10bit pipelined analog to digital converter. A switched capacitor topology is used for the T&H circuit and the amplifier is a folded cascode OTA with regulated cascode. The switches used are of transmission gate type. The thesis presents the design decisions, design phase and the theory needed to understand the design decisions and the considerations in the design phase. The results are based on circuit level SPICE simulations in Cadence with foundry provided BSIM3 transistor models. They show that the circuit has 10bit resolution and 7.6mW power consumption, for the worst-case frequency of 30MHz. The requirements on the dynamic performance are all fulfilled, most of them with large margins.

<p>This master thesis describes the design of a track-and-hold (T&H) circuit with 10bit resolution, 80MS/s and 30MHz bandwidth. It is designed in a 0.18µm CMOS process with a supply voltage of 1.8 Volt. The circuit is supposed to work together with a 10bit pipelined analog to digital converter. </p><p>A switched capacitor topology is used for the T&H circuit and the amplifier is a folded cascode OTA with regulated cascode. The switches used are of transmission gate type. </p><p>The thesis presents the design decisions, design phase and the theory needed to understand the design decisions and the considerations in the design phase. </p><p>The results are based on circuit level SPICE simulations in Cadence with foundry provided BSIM3 transistor models. They show that the circuit has 10bit resolution and 7.6mW power consumption, for the worst-case frequency of 30MHz. The requirements on the dynamic performance are all fulfilled, most of them with large margins.</p>