Spot core from the San Andreas Fault Observatory at Depth (SAFOD) borehole provides the opportunity to characterize and quantify damage and mineral alteration of siliciclastics within an active, large-displacement plate-boundary fault zone. Deformed arkosic, coarse-grained, pebbly sandstone, and fine-grained sandstone and siltstone retrieved from 2.55 km depth represent the western damaged zone of the San Andreas Fault, approximately 130 m west of the Southwest Deforming Zone (SDZ). The sandstone is cut by numerous subsidiary faults that display extensive evidence of repeating episodes of compaction, shear, dilation, and cementation. The subsidiary faults are grouped into three size classes: 1) small faults, 1 to 2 mm thick, that record an early stage of fault development, 2) intermediate-size faults, 2 to 3 mm thick, that show cataclastic grain size reduction and flow, extensive cementation, and alteration of host particles, and 3) large subsidiary faults that have cemented cataclastic zones up to 10 mm thick. The cataclasites contain fractured host-rock particles of quartz, oligoclase, and orthoclase, in addition to albite and laumontite produced by syn-deformation alteration reactions. Five structural units are distinguished in the subsidiary fault zones: fractured sandstones, brecciated sandstones, microbreccias, microbreccias within distinct shear zones, and principal slip surfaces. We have quantified the particle size distributions and the particle shape of the host rock mineral phases and the volume fraction of the alteration products for these representative structural units. Shape characteristics vary as a function of shear strain and grain size, with smooth, more circular particles evolving as a result of increasing shear strain. Overall, the particle sizes are consistent with a power law distribution over the particle size range investigated (0.3 µm < d < 400 µm). The exponent (fractal dimension, D) is found to increase with shear strain and volume fraction of laumontite. This overall increase in D and evolution of shape with increasing shear strain reflects a general transition from constrained comminution, active at low shear strains to abrasion processes that dominate at high shear strains.

A prominent landslide deposit in the Slope Basin seaward of the Megasplay Fault in the Nankai Trough was emplaced by a high-mobility landslide based on analysis of physical properties and seismic geomorphology. Slide acceleration is a critical variable that determines amplitude of slide-generated tsunami but is many times a variable with large uncertainty. In recent controlled laboratory experiments, the ratio of the shear stress to yield strength (defined as the Flow Factor) controls a wide spectrum of mass movement styles from slow, retrogressive failure to rapid, liquefied flows. Here, we apply this laboratory Flow Factor approach to a natural landslide in the Nankai Trough by constraining pre-failure particle size analysis and porosity. Several mass transport deposits (MTDs), were drilled and cored at Site C0021 in the Nankai Trough during International Ocean Discovery Program (IODP) Expedition 338. The largest, MTD B, occurs at 133-176 meters below seafloor and occurred approximately 0.87 Mya. Slide volume is 2 km3, transport distance is 5 km, and average deposit thickness is 50 m (maximum 180 m). Pre-failure water content was estimated from shallow sediments at Site C0018 (82%). The average grain size distribution is 37% clay-sized, 60% silt-sized, and 3% sand-size particles as determined by hydrometer analyses of the MTD. Together, the water content and clay fraction predict a Flow Factor of 3.5, which predicts a relatively high mobility slide. We interpret that the landslide that created MTD B was a single event that transported the slide mass relatively rapidly as opposed to a slow, episodic landslide event. This is supported by the observation of a completely evacuated source area with no remnant blocks or retrogressive headscarp and an internally chaotic seismic facies with large entrained blocks. This approach can be extended to other field settings characterized by fine-grained siliciclastics and where water content and clay percentages are known.

The iron ore mining industry makes use of various processes that result in the release of airborne dust into the surrounding atmosphere where workers are exposed, to produce a final product. The deposition in the lung and toxicological influences of airborne dust can be determined by their physical- and chemical characteristics. The Occupational Health and Safety Act (OHSA) regulations for hazardous chemical substances have no current system of how the physical- and chemical properties of particulates originating from specific areas will influence a worker‘s exposure and health, especially for ultrafine particles (UFP). It is therefore imperative to characterise airborne dust containing micrometer and UFP size particles originating from specific areas to determine if there are physical- and chemical characteristics that may or may not have an influence on the workers‘ health. Aim: This pilot study is aimed at the physical- and chemical characterisation of the airborne iron ore dust generated at the process areas of an opencast iron ore mine. Method: Sampled areas included the Primary-secondary crusher, Tertiary crusher, Quaternary crusher and Sifting house. Gravimetric sampling was conducted through the use of static inhalable- and respirable samplers in conjunction with optical- and condensation particle counters that were placed near airborne dust- emitting sources. Physical- and chemical characterisation was done with the use of scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Results: The results found in the study indicate high mass concentration levels of inhalable dust at all four process areas, as well as high levels of respirable dust found at the primary- secondary crusher area. Particle size distribution optical particle counter (OPC) results indicate that the majority of particles at all four process areas are in the region of 0.3 μm in size. Condensation particle counter (CPC) results integrated with OPC results indicate that at the primarysecondary and Tertiary crushers the majority of particles are found to be in the size fraction <0.3 μm. SEM analysis indicates that particle agglomeration largely occurs in the airborne iron ore dust. Particle splinters originating from larger particle collisions and breakages are present in the airborne dust. EDS analysis indicates that the elemental majority of the airborne iron ore dust consists of iron, oxygen, carbon, aluminium, silicon, potassium and calcium. The elemental percentages differ from each process area where an increase in iron and decrease in impurities can be seen as the ore moves through the beneficiation process from the Primary-secondary crusher to the Sifting house. Conclusion: The results obtained from the physical- and chemical properties of the airborne iron ore dust indicate high risk of over-exposure to the respiratory system, as well as possible ultrafine particle systemic exposure, that may overwhelm the physiological defense mechanisms of the human body and lead to reactive oxygen species (ROS) formation and the development of pathologies such as siderosis, silicasiderosis and lung cancer. / MSc (Occupational Hygiene), North-West University, Potchefstroom Campus, 2014

Pheroid is a patented system comprising of a unique submicron emulsion type formulation. Pheroid vesicles consist mainly of plant and essential fatty acids and can entrap, transport and deliver pharmacologically active compounds and other useful molecules. The aim of this study was to show that a modulation of components and parameters is necessary to obtain the optimum formula to be used in pharmaceutical preparations. Non-optimal or non-predictable stability properties of emulsions can be limiting for the applications of emulsions (Bjerregaard et al., 2001:23). Careful consideration was given to the apparatus used during the processing along with the ratios of the various components added to the formulation and the storage conditions of the Pheroid vesicles. A preliminary study was performed to optimize the most accurate processing parameters during emulsification. The effect of emulsification rate and time, the temperature of the aqueous phase, the number of days the water phase were gassed, the concentration of the surfactant, cremophor® RH 40, used and the concentration of Vitamin F Ethyl Ester CLR added to the oil phase of the o/w emulsion has been studied. Quantification of the mean particle size, zeta potential, turbidity, pH and current values were used to characterize the emulsions. The samples were characterised after 1, 2, 3, 7, 14, 21 and 28 days of storage. The emulsions were also characterised with confocal laser scanning microscopy (CLSM) to measure the number and size and size distribution of the vesicles. After determination of the processing variables influencing the emulsion stability an accelerated stability test was conducted on a final formula. In the present study, accelerated stability testing employing elevated temperatures and relative humidity were used with good accuracy to predict long-term stability of an o/w emulsion kept at both 5 and 25 OC with 60 % relative humidity and 40 OC with 75 % relative humidity. The results of the stability tests were presented in histograms of the physical properties 24 hours, 1 month, 2 months and 3 months after preparation of the emulsion. It was concluded that Pheroid vesicles demonstrate much potential as a drug delivery system. The high stability of this formula allows its use in a wide variety of applications in the pharmaceutical industry. / Thesis (M.Sc. (Pharmaceutics))--North-West University, Potchefstroom Campus, 2007.

The aims and objectives: The aims and objectives of this study were to characterize and compare the airborne particulate matter in the tankhouse and crusher areas of a base metal refinery sampled with two separate methods, in terms of mass concentration, nickel content, and particle size distribution. Methods: Area sampling was conducted in the two areas. Two methods were applied to collect particulate samples. The first is a multi–stage virtual impactor, the Respicon, which was used to determine the three critical particle fractions (inhalable, thoracic and respirable). The NIOSH 7300 method determined the particle concentration and nickel percentage present in each fraction. Using formulas provided by the manufacturers two additional particle–size fractions (extra–thoracic and trachea–bronchial) could be calculated. The second was based on the standard NIOSH 0500 method, which determined particle size distribution depicted as cumulative percentages. The samples were analyzed using laser scattering instrumentation. Results: In the tankhouse the highest level of exposure was to particles bigger than 10 um, with the highest nickel percentage also falling into this range. However, high nickel percentages were present in all three cut–off sizes (4 um, 10 um and > 10 um). The particle concentration for the crusher area was the highest for particulates bigger than 10 um, with the highest nickel percentage present in this fraction. After comparing the tankhouse and crusher areas, it is clear that the particle concentration is much higher in the crusher area according to all sampling methods used. The nickel content present in the analysis of these areas is of great concern. Conclusion: With the knowledge obtained through this research one hopes to establish a basis for particle size sampling in the platinum mining industry. This may lead to the development of health based OEL's and reflect a more accurate evaluation of workers particulate exposure. This information will give a greater understanding of health risks workers are exposed to. / Thesis (M.Sc. (Occupational Hygiene))--North-West University, Potchefstroom Campus, 2011.

Pheroid is a patented system comprising of a unique submicron emulsion type formulation. Pheroid vesicles consist mainly of plant and essential fatty acids and can entrap, transport and deliver pharmacologically active compounds and other useful molecules. The aim of this study was to show that a modulation of components and parameters is necessary to obtain the optimum formula to be used in pharmaceutical preparations. Non-optimal or non-predictable stability properties of emulsions can be limiting for the applications of emulsions (Bjerregaard et al., 2001:23). Careful consideration was given to the apparatus used during the processing along with the ratios of the various components added to the formulation and the storage conditions of the Pheroid vesicles. A preliminary study was performed to optimize the most accurate processing parameters during emulsification. The effect of emulsification rate and time, the temperature of the aqueous phase, the number of days the water phase were gassed, the concentration of the surfactant, cremophor® RH 40, used and the concentration of Vitamin F Ethyl Ester CLR added to the oil phase of the o/w emulsion has been studied. Quantification of the mean particle size, zeta potential, turbidity, pH and current values were used to characterize the emulsions. The samples were characterised after 1, 2, 3, 7, 14, 21 and 28 days of storage. The emulsions were also characterised with confocal laser scanning microscopy (CLSM) to measure the number and size and size distribution of the vesicles. After determination of the processing variables influencing the emulsion stability an accelerated stability test was conducted on a final formula. In the present study, accelerated stability testing employing elevated temperatures and relative humidity were used with good accuracy to predict long-term stability of an o/w emulsion kept at both 5 and 25 OC with 60 % relative humidity and 40 OC with 75 % relative humidity. The results of the stability tests were presented in histograms of the physical properties 24 hours, 1 month, 2 months and 3 months after preparation of the emulsion. It was concluded that Pheroid vesicles demonstrate much potential as a drug delivery system. The high stability of this formula allows its use in a wide variety of applications in the pharmaceutical industry. / Thesis (M.Sc. (Pharmaceutics))--North-West University, Potchefstroom Campus, 2007.

The aims and objectives: The aims and objectives of this study were to characterize and compare the airborne particulate matter in the tankhouse and crusher areas of a base metal refinery sampled with two separate methods, in terms of mass concentration, nickel content, and particle size distribution. Methods: Area sampling was conducted in the two areas. Two methods were applied to collect particulate samples. The first is a multi–stage virtual impactor, the Respicon, which was used to determine the three critical particle fractions (inhalable, thoracic and respirable). The NIOSH 7300 method determined the particle concentration and nickel percentage present in each fraction. Using formulas provided by the manufacturers two additional particle–size fractions (extra–thoracic and trachea–bronchial) could be calculated. The second was based on the standard NIOSH 0500 method, which determined particle size distribution depicted as cumulative percentages. The samples were analyzed using laser scattering instrumentation. Results: In the tankhouse the highest level of exposure was to particles bigger than 10 um, with the highest nickel percentage also falling into this range. However, high nickel percentages were present in all three cut–off sizes (4 um, 10 um and > 10 um). The particle concentration for the crusher area was the highest for particulates bigger than 10 um, with the highest nickel percentage present in this fraction. After comparing the tankhouse and crusher areas, it is clear that the particle concentration is much higher in the crusher area according to all sampling methods used. The nickel content present in the analysis of these areas is of great concern. Conclusion: With the knowledge obtained through this research one hopes to establish a basis for particle size sampling in the platinum mining industry. This may lead to the development of health based OEL's and reflect a more accurate evaluation of workers particulate exposure. This information will give a greater understanding of health risks workers are exposed to. / Thesis (M.Sc. (Occupational Hygiene))--North-West University, Potchefstroom Campus, 2011.

Antimony trioxide (Sb203) and halogenated additives are used together in flameretarded formulations due to their synergistic retardant properties. A study has been made to determine the effects of adding different grades of Sb203 (dSD particle sizes 0.11 um, 0.52um and 1.31 um) into ABS polymer either alone or with commercial brominated materials (BTBPE, TBBA, DBDPO) and an experimental bromine grade (sDBDPO). The Sb20 3 was added at 4wt% loadings and the bromines at 20wt% loadings. The results consider the influence of the additives on processing, mechanical, morphological and flame retardant properties. All compounds were produced using a twin-screw co-rotating extruder and then an injection moulder was used to mould notched impact (falling weight testing), flexural, LOI and UL-94 flame test bars. Samples of all the compounded formulations were titrated to determine Sb20 3 and Br contents. Fracture surface, morphology, size and dispersion analysis was carried out using both SEM and TEM equipment. Osmium tetroxide (OS04) staining was used to determine relative locations of filler particles and polybutadiene phase. Additions of the different antimony trioxide grades showed that the 0.52um and 1.31 um grades lowered impact energy absorption (-25 to -30%) when added at 4wt% loading. The use of a sub-micron size grade (0.1 um) did not significantly lower impact properties (-3%) and had similarly small effects on the flexural modulus and flexural strength. Additions of the brominated materials had much greater effects causing large reductions in impact properties (-20 to :70%). The presence of the bromines generally increased flexural modulus and lowered flexural strength with the exception of TB BA, which increased both modulus and strength. Compounds containing both 1.31 um Sb203 and bromines suffered a further reduction in impact energies, with the bromine properties dominating. Using the 0.1 um Sb20 3 grade again improved impact and flexural properties compared to the 1.31 um grade. The 0.1 um grade resulted in improvements in fire resistance as measured by the UL-94 properties when used with all bromine grades.

Diss. (sammanfattning) Stockholm : Karolinska institutet, 2007. / Härtill 5 uppsatser.

Diss. (sammanfattning) Uppsala : Sveriges lantbruksuniv., 2006. / Härtill 4 uppsatser.