Kyoto University (京都大学) / 0048 / 新制・論文博士 / 博士(工学) / 乙第12290号 / 論工博第4006号 / 新制||工||1450(附属図書館) / 26628 / UT51-2008-T61 / (主査)教授 檜山 爲次郎, 教授 松原 誠二郎, 教授 中條 善樹 / 学位規則第4条第2項該当

<p> High-end optical grade applications would benefit greatly from the unique mechanical and chemical properties of titanium alloys. However, the standard process of manufacturing optical components has not been explored in depth for titanium alloys. </p> <p> Thus the focus of this work was to extend ultra precision machining technology to produce optical grade surfaces on titanium components. An optical surface is characterized by surface roughness less than 10nm R_rms which are typically produced with single crystal diamond tools having a cutting edge radius on the order of 50-100 nm. A cutting speed of 60m/min, feed rate of 1.5 µm/ rev and depth of cut of 2 µm, was identified to achieve the surface finish target, but the practical limitation of this process was still with tool life and the rapid degradation of surface finish over time. </p> <p> This was attributed to the adhesion of titanium material on the tool that resulted in material pull out and side-flow during machining. Results obtained from the characterization of the tool and workpiece led to the identification of graphitization as the initial wear mechanism. As the cutting edge rounds-off due to graphitization, the rate of adhesion of the workpiece material onto the tool increased. For this reason solutions were explored that would reduce the graphitization process and delay the onset of intense adhension. </p> <p> Thus a coating technology involving Perfluoro Polyether (PFPE) was chosen. Tribometer analysis under a load of 500N and temperature of 450ºC between the uncoated and PFPE coated diamond tools and titanium pins showed a remarkable reduction in COF from 0.275 to 0.05. A significant enhancement in tool life and surface quality was also achieved in single point diamond turning (SPDT) of titanium alloys using PFPE coated diamond tools. Tool life was based on an assessment of the cutting length achieved before the surface roughness exceeded the targeted value of 10 nm R_rms and it improved from 1.25 km and 5.1 km with PFPE coated tools. </p> / Thesis / Doctor of Philosophy (PhD)

Two diazonium perfluoroalkyl arylsulfonimide (PFSI) zwitterionic monomers, 4-diazonium perfluoro(3-oxapent-4-ene)benzenesulfonimide (I) and 4-(trifluoromethyl)-2-diazonium perfluoro(3-oxapent-4-ene)benzenesulfonimide (II) have been synthesized from perfluoro(3-oxapent-4-ene) sulfonyl fluoride (POPF) for proton exchange membrane fuel cells. PFSI polymers are proposed as new electrolytes due to their better thermal stability, inertness to electrochemical conditions, and lower susceptibility to oxidative degradation and dehydration. For a better integration between the electrode and the electrolyte, the PFSI polymers are expected to be grafted onto the carbon electrode via the diazonium moiety. All the reaction intermediates and the final product were characterized with 1H NMR, 19F NMR and IR spectroscopies.

This thesis deals with the design of 18F- and 68Ga-labelled positron emission tomography (PET) tracers and the development of technologies that enable faster and simpler preparation with high specific radioactivity. Techniques like microwave heating and reducing the concentrations of the precursor were investigated with this perspective. A few applications were explored using molecular design perspectives. A nucleophilic 18F-labelling strategy using perfluoro-containing leaving groups was explored. We observed that [18F]fluoride was interacting with the perfluoro alkyl chains of the substrate, preventing the nucleophilic substitution from taking place. When a perfluoroaryl group was instead used in the leaving group, the substitution took place and purification by fluorous solid-phase extraction was possible. 18F-Labelled analogues of the monoamine oxidase-A inhibitor harmine were prepared by one-step nucleophilic fluorinations and evaluated by in vitro autoradiography, showing high specific binding. Biotin analogues labelled with 18F and 68Ga were prepared and their binding to avidin evaluated. All analogues retained their binding ability and will be further evaluated in transplantation models with avidin-coated islets of Langerhans. Peptide design perspectives were used in some examples where the Arg-Gly-Asp (RGD) sequence and a single-chain version of vascular endothelial growth factor (VEGF) protein functionalized with 2,2',2'',2'''-(1,4,7,10-tetraazacyclododecane-1,4,7,10-tetrayl)tetraacetic acid (DOTA) or 2,2',2''-(1,4,7-triazonane-1,4,7-triyl)triacetic acid (NOTA) as chelators were labelled with 68Ga. The RGD motif and VEGF have high affinity for, respectively, αvβ3 integrin and VEGFR-2 receptor that are overexpressed in angiogenesis process. The 68Ga-labelled scVEGF maintained its functional activity in vitro. A polypeptide conjugate containing phosphocholine, which has affinity for the C-reactive protein released during the inflammatory process, was labelled with 68Ga for the development of an imaging agent for inflammation in vivo. Finally [18F]/19F exchange in fluorine-containing compounds was studied in order to investigate whether the exchange reaction can be of practical use for labelling.

The objective of the research is to synthesize the diazonium N-(perfluoroalkyl) benzenesulfonimide (PFSI)zwitterionicpolymers as electrolytes in polymerelectrolyte membrane (PEM) fuel cells. The proposed diazoniumPFSI zwitterionic polymer (I) is expected to enhance the thermal and chemical stability, increase the proton conductivity of electrolytes, and improve the catalyst efficiency for PEM fuel cells. Synthesis of the perfluorobenzoyl peroxide initiator, homopolymerization of perfluoro (3-oxapent-4-ene) sulfonyl fluoride,coupling reaction with4-sulfamonylacetanilide, couplingreaction with 4-nitrobenzene sulfonyl amide, n-deacetylation reaction, and diazotization reactionhave been carried outsuccessfully in the lab. The intermediate chemicals are characterized by GC-MS, IR, NMR, and GPC spectroscopies.

No description available.

<p> Per- and polyfluoroalkyl substances (PFAS) are a class of persistent environmental contaminants that have become ubiquitous, resulting in widespread exposure among humans and wildlife. Amphibians are regularly exposed in the field, making them susceptible to sublethal effects of PFAS exposure. In amphibians exposed to PFAS, deleterious effects have been observed, including reduction in body condition measured using the scaled mass index (SMI) and degraded hepatic condition, among others. PFAS may dysregulate lipid metabolism by altering signaling cascades regulated by peroxisome proliferator activated receptors (PPAR), but whether changes in energy stores can explain changes in amphibian SMI and/or hepatic condition remain underexplored. Since lipids are a critical energy reserve for anurans, understanding whether lipid metabolism is being perturbed is critical. The central objective of this thesis was to investigate the effect of PFAS on lipid homeostasis in <em>Xenopus laevis </em>tadpoles within the context of a PPAR mechanism of action (MOA), considering apical, molecular, and lipidomic endpoints. I conducted three studies: (a) a study to characterize SMI and the relative expression of the hepatic xPPARα/β/γ during metamorphosis, (b) a pharmaceutical exposure to assess the <em>in vivo</em> effects of xPPARα/β/γ agonism on hepatic gene expression for select downstream targets (<em>apoa5, fabp1, acox1,​ pck1</em>), and (c) a chronic PFAS exposure to investigate the effects of environmentally relevant concentrations (PFOS, PFHxS, PFOA, PFHxA at 0.5 ppb; binary mixture of PFOS:PFHxS at 1 ppb) on lipid homeostasis through apical endpoints (mass, snout vent length, SMI, hepatic condition), relative hepatic gene expression, and Multiple Reaction Monitoring (MRM) profiling of the hepatic lipidome for changes in relative class abundance. In study (a), I identified SMI and hepatic expression of <em>xPPARα/β/γ</em> is dynamic during late metamorphosis, indicating the potential for heightened susceptibility. However, in study (b), pharmaceutical agonists had no effect on <em>X. laevis</em> at high doses. For study (c), I did not observe effects on a majority of apical endpoints, including SMI, but detected a significant sex-specific reduction in hepatic condition for male<em> X. laevis</em> tadpoles exposed to single-chemical perfluorosulfonic acid (PFSA) treatments. For gene expression, I observed a transient downregulation for apolipoprotein-V (<em>apoa5</em>) at Nieuwkoop and Faber (NF) stage 62 for <em>X. laevis</em> tadpoles exposed to single-chemical perfluorocarboxylic acid (PFCA) treatments. Lipid profiling detected transient dysregulation of predominantly membrane lipids in-response to short-chain PFAS treatments at NF 58. Overall, our findings indicate PFAS may exert toxicity during anuran metamorphosis through multiple mechanisms of action (MOA) with sex-specific and developmental-stage specific outcomes.</p>

Le travail présenté dans ce mémoire consiste à élaborer en une seule étape une couche mince organique ayant les propriétés chimiques et/ou morphologiques souhaitées. Cette démarche vise à copolymériser par voie plasma (PECVD) deux monomères antagonistes (apolaire et polaire) afin de contrôler la répartition et la taille des nodules de l’un des polymères dispersé dans l’autre phase et d’obtenir ainsi une structuration chimique et/ou morphologique. Pour ce faire, six précurseurs ont été sélectionnés de façon à couvrir une large gamme de polarité: l’alcool allylique (AA), l’acide acrylique (AAc), l’aniline (ANi), le diéthylèneglycol diméthyl éther (DEGDME), le 1H,1H,2H-perfluoro-1-décène (HDFD) et le 2-(diméthylamino) éthyle méthacrylate (DMAEMA).La première partie de ce travail est centrée sur l’étude des mécanismes de croissance des différents homopolymères par voie plasma pulsé. Les cinétiques de dépôt, les structures chimiques et les morphologies sont plus spécifiquement détaillées pour deux monomères, les HDFD et DMAEMA en fonction des paramètres du procédé plasma, la polymérisation plasma de ces deux précurseurs étant pour la première fois décrite. La caractérisation des couches minces obtenues repose sur la spectroscopie Infrarouge à Transformée de Fourier (FTIR), la spectroscopie de photoélectrons X (XPS) et la microscopie à force atomique (AFM). Cette étude a montré le rôle catalytique des groupements fluorés induisant des vitesses de dépôt plus conséquentes. Même si la croissance est prépondérante durant le temps de décharge, le dépôt est non négligeable pendant la post-décharge. La structure chimique des polymères plasma est fortement dépendante des paramètres de la décharge et notamment la puissance et le temps de décharge. La spectroscopie FTIR s’est révélée comme un outil performant pour l’évaluation de la rétention de la structure chimique de l’entité monomère initiale dans le polymère plasma. Ces homopolymères présentent une morphologie homogène sans rugosité.Dans la deuxième partie, nous abordons la copolymérisation plasma pulsé. Les différents copolymères synthétisés sont p-AA-co-HDFD, p-AAc-co-HDFD, p-ANi-co-HDFD, p-DEGDME-co-HDFD, p-DMAEMA-co-HDFD, p-DMAEMA-co-ANi. La plupart sont issus de comonomères hydrophiles et hydrophobes à l’exception d’un synthétisé à partir de deux précurseurs polaires. Les cinétiques de dépôt, les propriétés chimiques et morphologiques sont discutées en fonction des paramètres plasma tels que la puissance injectée mais aussi des proportions relatives des différents comonomères. Les différentes analyses chimiques entreprises montrent plutôt la formation d’un mélange d’homopolymères ou d’un copolymère à bloc plutôt que la croissance d’un nouveau matériau. Cette hypothèse est étayée par la mise en évidence d’une structuration morphologique correspondant à la présence d’îlots à la surface. / The work presented in this thesis consists to elaborate only in one step a thin organic layer having the required chemical and/or morphological properties. This approach aims to plasma copolymerize (PECVD) two antagonistic monomers (nonpolar and polar) in order of controlling the repartition and the size of nodules of one of the polymers dispersed in the other phase and thus, of inducting a chemical and/or morphological structuring. For this, six precursors have been selected to cover a large range of polarity: allyl alcohol (AA), acrylic acid (AAc), aniline (ANi), the diethylene glycol dimethyl ether (DEGDME), the 1H,1H,2H-perfluor-1-decene (HDFD) and 2-(dimethylamino)ethyl methacrylate (DMAEMA).The first part of this work is centered on studying the growth mechanism of different homo-polymers through pulsed plasma. The kinetics of deposition, the chemical structures and morphologies are more specifically detailed for two monomers, HDFD and DMAEMA in function of plasma parameters, the plasma polymerization of these two precursors being described for the first time. The thin layers were characterized through Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). This study showed the catalytic role of fluorine groups inducing more consequent deposit rates. Even if the growth is significant during the plasma on-time, the deposit is not negligible during the plasma off-time. The chemical structure of plasma polymers is highly dependent on the discharge parameters and mainly the power and the pulse period. The FTIR spectroscopy was shown to be a relevant tool for evaluating the chemical structure’s retention of the initial monomer entity in the plasma polymer. These homopolymers present a homogenous morphology without roughness.In the second part, the pulsed plasma copolymerization is described. The different synthesized copolymers are p-AA-co-HDFD, p-AAc-co-HDFD, p-ANi-co-HDFD, p-DEGDME-co-HDFD, p-DMAEMA-co-HDFD, p-DMAEMA-co-ANi. The majorities are issued from hydrophilic and hydrophobic co-monomers excepted for one synthesized from two polar precursors. The kinetics of deposits, the chemical and morphological properties were discussed in function to plasma parameters such as the injected power as well as the relative proportions of different co-monomers. The different chemical analyses showed the formation of a mixture of homopolymers or of a block copolymer rather than the growth of a new material. This hypothesis is unsubstantiated by evidencing a morphological structuring corresponding to the presence of spherical nanostructure at the surface.

Le travail présenté dans ce mémoire consiste à élaborer en une seule étape une couche mince organique ayant les propriétés chimiques et/ou morphologiques souhaitées. Cette démarche vise à copolymériser par voie plasma (PECVD) deux monomères antagonistes (apolaire et polaire) afin de contrôler la répartition et la taille des nodules de l'un des polymères dispersé dans l'autre phase et d'obtenir ainsi une structuration chimique et/ou morphologique. Pour ce faire, six précurseurs ont été sélectionnés de façon à couvrir une large gamme de polarité: l'alcool allylique (AA), l'acide acrylique (AAc), l'aniline (ANi), le diéthylèneglycol diméthyl éther (DEGDME), le 1H,1H,2H-perfluoro-1-décène (HDFD) et le 2-(diméthylamino) éthyle méthacrylate (DMAEMA).La première partie de ce travail est centrée sur l'étude des mécanismes de croissance des différents homopolymères par voie plasma pulsé. Les cinétiques de dépôt, les structures chimiques et les morphologies sont plus spécifiquement détaillées pour deux monomères, les HDFD et DMAEMA en fonction des paramètres du procédé plasma, la polymérisation plasma de ces deux précurseurs étant pour la première fois décrite. La caractérisation des couches minces obtenues repose sur la spectroscopie Infrarouge à Transformée de Fourier (FTIR), la spectroscopie de photoélectrons X (XPS) et la microscopie à force atomique (AFM). Cette étude a montré le rôle catalytique des groupements fluorés induisant des vitesses de dépôt plus conséquentes. Même si la croissance est prépondérante durant le temps de décharge, le dépôt est non négligeable pendant la post-décharge. La structure chimique des polymères plasma est fortement dépendante des paramètres de la décharge et notamment la puissance et le temps de décharge. La spectroscopie FTIR s'est révélée comme un outil performant pour l'évaluation de la rétention de la structure chimique de l'entité monomère initiale dans le polymère plasma. Ces homopolymères présentent une morphologie homogène sans rugosité.Dans la deuxième partie, nous abordons la copolymérisation plasma pulsé. Les différents copolymères synthétisés sont p-AA-co-HDFD, p-AAc-co-HDFD, p-ANi-co-HDFD, p-DEGDME-co-HDFD, p-DMAEMA-co-HDFD, p-DMAEMA-co-ANi. La plupart sont issus de comonomères hydrophiles et hydrophobes à l'exception d'un synthétisé à partir de deux précurseurs polaires. Les cinétiques de dépôt, les propriétés chimiques et morphologiques sont discutées en fonction des paramètres plasma tels que la puissance injectée mais aussi des proportions relatives des différents comonomères. Les différentes analyses chimiques entreprises montrent plutôt la formation d'un mélange d'homopolymères ou d'un copolymère à bloc plutôt que la croissance d'un nouveau matériau. Cette hypothèse est étayée par la mise en évidence d'une structuration morphologique correspondant à la présence d'îlots à la surface.