Organic electronics based on π-conjugated semi-conductor raises new technology, such as organic film transistors, e-paper, and organic photovoltaic cells that can be implemented cost-effectively on large-area applications. Currently, the device performance is limited by low charge carrier mobility. Poly(3-hexylthiophene) (P3HT) and organic field effect transistors (OFET) is used as a model to investigate morphology of the organic film and corresponding electronic properties. In this thesis, processing parameters such as boiling points and solubility are controlled to impact the micro- and macro-morphology of the film to enhance the charge transport of the device. Alternative approach to improve ordering of polymer chains and increase in charge transport without post-treatment of P3HT solution is studied. The addition of high boiling good solvent to the relatively low boiling main solvent forms ordered packing of π-conjugated polymers during the deposition process. We show that addition of 1% of dichlorobenzene (DCB) to the chloroform based P3HT solution was sufficient to improve wetting and molecular structures of the film to increase carrier mobility. Systematic study of solvent-assisted re-annealing technique, which has potential application in OFET encapsulation and fabrication of top-contact OFET, is conducted to improve mobility of OFET, and, to suggest a cost-effective processing condition suitable for industrial application. Three process parameters: boiling point, polarity, and solubility are investigated to further understand the trend of film response to the solvent-assisted technique. We report the high boiling non-polar solvents with relatively high RED values promote highest improvement in molecular packing and formulate crystalline structure of the thin film, which increases the device performance.

Externally initiated o-tolyl initiated poly(3-hexylthiophene) (P3HT) was synthesized according to Grignard metathesis polymerization at varying chain length to compare number average molecular weights (Mn) obtained by gel permeation chromatography (GPC) and 1H NMR end group analysis. The extent of overestimation by GPC (1.3) was determined to be lower than previously reported for low Mn polymers. However, an apparent GPC quantification limit was observed as NMR Mn correlated well to predicted results. Static light scattering studies on high Mn polymers provided evidence that the true molecular weight was more similar to GPC-derived Mn. Despite nearly 100% external initiation efficiency, at a certain Mn limit new uninitiated chains may be synthesized. It is suggested that the synthesis of externally initiated P3HT should be limited to Mn below 40 kDa to ensure fully externally initiated chains. A proposal for the synthesis of externally initiated macrocyclic P3HT will also be discussed.

Externally initiated o-tolyl initiated poly(3-hexylthiophene) (P3HT) was synthesized according to Grignard metathesis polymerization at varying chain length to compare number average molecular weights (Mn) obtained by gel permeation chromatography (GPC) and 1H NMR end group analysis. The extent of overestimation by GPC (1.3) was determined to be lower than previously reported for low Mn polymers. However, an apparent GPC quantification limit was observed as NMR Mn correlated well to predicted results. Static light scattering studies on high Mn polymers provided evidence that the true molecular weight was more similar to GPC-derived Mn. Despite nearly 100% external initiation efficiency, at a certain Mn limit new uninitiated chains may be synthesized. It is suggested that the synthesis of externally initiated P3HT should be limited to Mn below 40 kDa to ensure fully externally initiated chains. A proposal for the synthesis of externally initiated macrocyclic P3HT will also be discussed.

Made available in DSpace on 2016-12-08T17:19:27Z (GMT). No. of bitstreams: 1 JULIA GASCHO.pdf: 2752130 bytes, checksum: ac987e92d5bc395ba52a7917285e8cf8 (MD5) Previous issue date: 2015-07-28 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Materiais condutores transparentes, ou CTs, são aqueles que apresentam as propriedades de elevada condutividade elétrica e transparência. Na fabricação de diversos dispositivos eletrônicos, tais como células solares, monitores de cristal líquido e telas sensíveis ao toque, esses materiais são componentes críticos, devido a não existirem muitos materiais condutores e transparentes. O óxido de índio e estanho (ITO) é o material mais utilizado como CT, devido à sua elevada condutividade elétrica e transparência. Porém, a utilização deste possui algumas desvantagens, como custo elevado e fragilidade. Devido a isto, novos materiais estão sendo estudados para a sua substituição, tais como grafeno e polímeros conjugados. Sistemas grafeno/polímero conjugado exibem, normalmente, elevada condutividade elétrica, estabilidade química e são capazes de armazenar energia. Sendo assim, este trabalho teve como objetivo produzir filmes de óxido de grafeno (OG) e óxido de grafeno reduzido (OGR), verificando a eficiência dos métodos de oxidação e redução utilizados. Também foram estudados filmes de OG e OGR com poli(3-hexiltiofeno) (P3HT), verificando as alterações nas propriedades destes após a deposição do polímero sobre os mesmos, com vistas a uma possível utilização desses sistemas como condutores transparentes. O OG foi produzido a partir da grafite pelo método de Hummers modificado e, posteriormente reduzido quimicamente, com NaBH4, ou termicamente, em forno tubular. Os filmes poliméricos foram preparados por casting a partir de uma solução de P(3HT) em clorofórmio, depositada sobre os filmes de OG. As caracterizações por ângulo de contato, FTIR, DRX, e espectroscopia de impedância comprovaram a eficiência na oxidação da grafite. Os filmes de OG produzidos se apresentaram translúcidos e semicondutores, com condutividade da ordem de 10-6 a 10-4 S/m. Foram obtidos filmes finos com uma superfície lisa e praticamente sem defeitos. Os filmes de OG apresentaram ângulo de contato com a água de 31,5 e 38,9° e tensão superficial de 63,6 e 59,2 mJ/m², o que indica a hidrofilicidade dos mesmos. Observou-se uma redução parcial do OG, tanto na redução química quanto térmica, com filmes menos translúcidos e mais condutores do que os filmes de OG (condutividade próximas à 10-3 e 10-1 S/m, respectivamente). Foram obtidos filmes de OG reduzido quimicamente finos, lisos e praticamente sem defeitos, porém, os filmes de OG reduzidos termicamente se mostraram irregulares e mais espessos. Através da redução química foram obtidos filmes hidrofóbicos, com ângulo de contato com a água acima de 90° e tensão superficial de 30,1 mJ/m². Enquanto a redução térmica produziu filmes com ângulo de contato com a água um pouco abaixo de 90° e tensões superficiais de 31,2 e 32,1 mJ/m², bem menos hidrofílicos do que os filmes de OG. A adição do filme polimérico sobre os filmes de OG não alterou significativamente as propriedades de condutividade elétrica e diminuiu minimamente a transparência destes.

>Magister Scientiae - MSc / This thesis starts with the reviewing of studies on the loading of noble metals and nanostructured metal oxides into bulk heterojunction organic solar cell device architectures. The reviews focused on the innovative developments in the use of various fullerene derivatives as electron acceptors in organic solar cells. It additionally reflected on the effect of metallic nanoparticles (NPs), such as gold (Au) and silver (Ag), on the performance of organic solar cells. Besides the metallic NPs, the effect of metal oxide nanoparticle loading, e.g. CuO, ZnO and TiO2, on the organic solar cell performance, and the use of noble metals doped TiO2 on the gas sensing application were reviewed. / 2024

Dans cette étude, des copolymères à blocs rigide-flexible comprenant des segments donneur [poly(3-hexylthiophène) régiorégulier, (rr-P3HT)] et accepteurs d’électrons (C60) ont été synthétisés. L’auto-assemblage en masse de ces copolymères à blocs avait pour objectif d’atteindre des morphologies dont la taille des domaines coïncide avec la distance idéale de transport de l’exciton (~10 nm) en vue d’utiliser ces systèmes comme matériaux de couche active dans les cellules photovoltaïques organiques de type P3HT-PCBM.La maîtrise et l'optimisation des conditions de synthèse de rr-P3HT de fonctionnalité terminale bien définie nous ont permis d'accéder à différentes architectures de copolymères linéaires di- et triblocs, constitués de P3HT comme bloc rigide et de polystyrène ou poly(4-vinylpyridine) comme bloc ‘flexible’. La fonctionnalisation du bloc flexible avec des dérivés du fullerène (C60 ou PCBM) a ensuite été réalisée et ces copolymères utilisés comme additifs pour stabiliser la morphologie de la couche active des cellules solaires organiques de type P3HT/PCBM. Les caractéristiques photovoltaïques des matériaux ainsi préparés ont été déterminées et corrélées aux analyses morphologiques de la couche active. / The performance of organic photovoltaic cells mainly depends on the active layer nano-morphology. Rod-coil block copolymers (BCPs) are well known in their ability to self-assemble into well-ordered nanoscopic morphologies. BCPs containing electron-donor and acceptor segments are of particular interest for use in photovoltaic cells because electronic light-excited states exist over distances similar to the typical size of block copolymer domains (~10 nm). Therefore, we designed novel donor-acceptor BCPs to exploit this coincidence in dimensions. This thesis is focused on BCPs based on regioregular poly(3-hexylthiophene) (rr-P3HT) due to its high hole mobility and good processibility from various solvents. Simplified and versatile syntheses of donor-acceptor rod-coil di- and tri- BCPs consisting of the donor block P3HT (rod) and polystyrene or poly(4-vinylpyridine) (coil) blocks to carry the acceptor C60 in different ways were developed. These materials were used as surfactants to stabilize the nano-morphology of reference P3HT: [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) based devices. Photovoltaic characterizations were then tied to copolymer structural data with the help of AFM and a range of complementary characterization techniques.

The aim of the present work was to screen the main methods for the synthesis of conjugated polymers for their suitability in the preparation of conductive polymer brushes. The main focus was put on the grafting of intrinsically soluble substituted regioregular polyalkylthiophenes because of their excellent optoelectronic properties. The resulting polymer films were characterized and their optoelectrical properties studied. For the first time, a synthesis of conductive polymer brushes on solid substrates using “grafting-from” method was performed. The most important, from my opinion, finding of this work is that regioregular head-to-tail poly-3-alkylthiophenes – benchmark materials for organic electronics - can be now selectively grafted from appropriately-terminated surfaces to produce polymer brushes of otherwise soluble polymers - the architecture earlier accessible only in the case of non-conductive polymers. In particular, we developed a new method to grow P3ATs via Kumada Catalyst Transfer Polymerization (KCTP) of 2-bromo-5-chloromagnesio-3-alkylthiophene. Exposure of the initiator layers to monomer solutions leads to selective chain-growth polycondensation of the monomers from the surface, resulting into P3AT brushes in a very economical way. The grafting process was investigated in detail and the structure of the resulting composite films was elucidated using several methods. The obtained data suggests that the grafting process occurs not only at the poly(4-bromstyrene) (PS-Br)/polymerization solution interface, but also deeply inside the swollen PS-Br films, penetrable for the catalyst and for the monomer The grafting process was investigated in detail and the structure of the resulting composite film was elucidated using ellipsometry, X-ray Photoelectron Spectroscopy (XPS), Rutherford backscattering spectroscopy (RBS), and Conductive atomic force microscopy (C-AFM). The obtained data suggests that the grafting process occurs not only at the poly(4-bromostyrene), PS-Br/polymerization solution interface, but also deeply inside the swollen PS-Br film, which is penetrable for the catalyst and the monomer. The process results in an interpenetrated PS-Br/P3HT network, in which relatively short poly(3-hexylthiophene), P3HT grafts emanate from long, cross-linked PS-Br chains. A further method investigated during our work was to covalently graft regioirregular P3HT to substrates modified by macromolecular anchors using oxidative polymerization of 3HT with FeCl3. P3HT layers with variable thicknesses from 30 nm up to 200 nm were produced using two steps of polymerization reaction. The P3HT obtained by oxidative polymerization had always an irregular structure, which was a result of the starting monomer being asymmetric, which is undesired for electronic applications. The third method for the production of conductive polymer brushes was to graft regioregular poly(3,3''-dioctyl-[2,2';5',2'']terthiophene) (PDOTT) by electrochemical oxidative polycondensation of symmetrically substituted 3,3''-dioctyl-[2,2';5',2'']terthiophene (DOTT). A modification of the supporting ITO electrode by the self-assembled monolayers (SAMs) of compounds having polymerizable head-groups with properly adjusted oxidative potentials was found to be essential to achieve a covalent attachment of PDOTT chains. The polymer films produced show solvatochromism and electrochromism, as well as the previous two methods. After polymerization, the next step towards building organic electronic devices is applying the methods obtained in nano- and microscale production. Block copolymers constitute an attractive option for such surface-engineering, due to their ability to form a variety of nanoscale ordered phase-separated structures. However, block copolymers containing conjugated blocks are less abundant compared to their non-conjugated counterparts. Additionally, their phase behaviour at surfaces is not always predictable. We demonstrated in this work, how surface structures of non-conductive block copolymers, such as P4VP-b-PS-I, can be converted into (semi)conductive P4VP-b-PS-graft-P3HT chains via a surface-initiated polymerization of P3HT (Kumada Catalyst Transfer Polymerization (KCTP) from reactive surface-grafted block copolymers. This proves that our method is applicable to develop structured brushes of conductive polymers. We believe that it can be further exploited for novel, stimuli-responsive materials, for the construction of sensors, or for building various opto-electronic devices. The methods developed here can in principle be adapted for the preparation of any conductive block copolymers and conductive polymers, including other interesting architectures of conductive polymers, such as block copolymers, cylindrical brushes, star-like polymers, etc. To this end, one needs to synthesize properly-designed and multi-functional Ni-initiators before performing the polycondensation.

The aim of the present work was to screen the main methods for the synthesis of conjugated polymers for their suitability in the preparation of conductive polymer brushes. The main focus was put on the grafting of intrinsically soluble substituted regioregular polyalkylthiophenes because of their excellent optoelectronic properties. The resulting polymer films were characterized and their optoelectrical properties studied. For the first time, a synthesis of conductive polymer brushes on solid substrates using “grafting-from” method was performed. The most important, from my opinion, finding of this work is that regioregular head-to-tail poly-3-alkylthiophenes – benchmark materials for organic electronics - can be now selectively grafted from appropriately-terminated surfaces to produce polymer brushes of otherwise soluble polymers - the architecture earlier accessible only in the case of non-conductive polymers. In particular, we developed a new method to grow P3ATs via Kumada Catalyst Transfer Polymerization (KCTP) of 2-bromo-5-chloromagnesio-3-alkylthiophene. Exposure of the initiator layers to monomer solutions leads to selective chain-growth polycondensation of the monomers from the surface, resulting into P3AT brushes in a very economical way. The grafting process was investigated in detail and the structure of the resulting composite films was elucidated using several methods. The obtained data suggests that the grafting process occurs not only at the poly(4-bromstyrene) (PS-Br)/polymerization solution interface, but also deeply inside the swollen PS-Br films, penetrable for the catalyst and for the monomer The grafting process was investigated in detail and the structure of the resulting composite film was elucidated using ellipsometry, X-ray Photoelectron Spectroscopy (XPS), Rutherford backscattering spectroscopy (RBS), and Conductive atomic force microscopy (C-AFM). The obtained data suggests that the grafting process occurs not only at the poly(4-bromostyrene), PS-Br/polymerization solution interface, but also deeply inside the swollen PS-Br film, which is penetrable for the catalyst and the monomer. The process results in an interpenetrated PS-Br/P3HT network, in which relatively short poly(3-hexylthiophene), P3HT grafts emanate from long, cross-linked PS-Br chains. A further method investigated during our work was to covalently graft regioirregular P3HT to substrates modified by macromolecular anchors using oxidative polymerization of 3HT with FeCl3. P3HT layers with variable thicknesses from 30 nm up to 200 nm were produced using two steps of polymerization reaction. The P3HT obtained by oxidative polymerization had always an irregular structure, which was a result of the starting monomer being asymmetric, which is undesired for electronic applications. The third method for the production of conductive polymer brushes was to graft regioregular poly(3,3''-dioctyl-[2,2';5',2'']terthiophene) (PDOTT) by electrochemical oxidative polycondensation of symmetrically substituted 3,3''-dioctyl-[2,2';5',2'']terthiophene (DOTT). A modification of the supporting ITO electrode by the self-assembled monolayers (SAMs) of compounds having polymerizable head-groups with properly adjusted oxidative potentials was found to be essential to achieve a covalent attachment of PDOTT chains. The polymer films produced show solvatochromism and electrochromism, as well as the previous two methods. After polymerization, the next step towards building organic electronic devices is applying the methods obtained in nano- and microscale production. Block copolymers constitute an attractive option for such surface-engineering, due to their ability to form a variety of nanoscale ordered phase-separated structures. However, block copolymers containing conjugated blocks are less abundant compared to their non-conjugated counterparts. Additionally, their phase behaviour at surfaces is not always predictable. We demonstrated in this work, how surface structures of non-conductive block copolymers, such as P4VP-b-PS-I, can be converted into (semi)conductive P4VP-b-PS-graft-P3HT chains via a surface-initiated polymerization of P3HT (Kumada Catalyst Transfer Polymerization (KCTP) from reactive surface-grafted block copolymers. This proves that our method is applicable to develop structured brushes of conductive polymers. We believe that it can be further exploited for novel, stimuli-responsive materials, for the construction of sensors, or for building various opto-electronic devices. The methods developed here can in principle be adapted for the preparation of any conductive block copolymers and conductive polymers, including other interesting architectures of conductive polymers, such as block copolymers, cylindrical brushes, star-like polymers, etc. To this end, one needs to synthesize properly-designed and multi-functional Ni-initiators before performing the polycondensation.

Ce travail de recherche pluridisciplinaire a consisté en l'étude de cellules photovoltaïques organiques à base de nouveaux copolymères à blocs de type rigide-flexible. L'idée était de proposer une alternative aux mélanges donneur/accepteur, dont la morphologie en film est très difficile à contrôler, en élaborant de nouveaux matériaux conjugués capables de s'auto-organiser et de créer une nano-structuration de la couche active, permettant ainsi d'optimiser certains paramètres du processus photovoltaïque (dissociation de l'exciton, conduction des charges vers les électrodes). La première étape a consisté à développer une synthèse simplifiée et versatile de copolymères constitués d'un bloc conjugué donneur (poly(3-hexylthiophène), d'un bloc flexible polystyrène, et d'un accepteur d'électron (C60). La seconde étape a consisté à caractériser ces matériaux originaux en tant que couche active ou compatibilisants dans des dispositifs photovoltaïques organiques et ainsi montrer leur potentiel. / This multidisciplinary work deals with the study of organic photovoltaic cells based on new rod-coil block copolymers. The aim was to replace donor/acceptor blends which are currently limited by poor control over their thin-film morphology. It was expected that the new materials may self-assemble to give a nano-structuration of the active layer, and thereby optimize the principal physical photovoltaic processes, namely exciton separation and conduction of charge-carriers through the film to the electrodes. A versatile and simplified synthesis of rod-coil copolymers consisting of a donor conjugated block [poly(3-hexylthiophene], a flexible block (polystyrene) and an electron acceptor (C60) was developed. The characterization of the new materials demonstrated their potential as an active layer or compatibilizer in photovoltaic devices.

Le but de cette thèse était d’élaborer et d’étudier des films minces hybrides orientés et nanostructurés composés d’un polymère semi-conducteur, le poly(3-hexylthiophène) regiorégulier (P3HT) et de nanocristaux semiconducteurs de CdSe (sphères, bâtonnets). Pour cela, deux méthodes ont été mises en œuvre: la croissance épitaxiale directionnelle et le brossage mécanique. Les films de P3HT purs épitaxiés et brossés se différencient en termes de nanomorphologie, d’ordre cristallin et de structure. Les premiers présentent une morphologie lamellaire et une structure de fibre où les chaînes conjuguées sont alignées suivant l’axe de fibre. Les films brossés ne présentent pas de structure lamellaire et les domaines cristallins sont orientés préférentiellement «flat-on». Ces différences se reflètent dans les propriétés optiques des films épitaxiés et brossés. Le degré d’orientation des films brossés dépend fortement du poids moléculaire et une forte anisotropie du transport de charges a été observée. Les films hybrides épitaxiés sont nanostructurés avec localisation des nanocristaux dans les zones amorphes du P3HT. Par ailleurs, l’analyse par tomographie électronique de ces films montre une structure en bicouche avec une couche hybride surmontée d’une couche de P3HT pur. Les films hybrides brossés montrent clairement un alignement des nanobâtonnets de CdSe et des chaînes du P3HT parallèlement à l’axe du brossage. Les degrés d’orientation du P3HT et des nanobâtonnets sont corrélés et dépendent de la proportion en nanoparticules indiquant que c’est la matrice polymère qui induit l’orientation des nanobâtonnets. / The aim of this thesis was to elaborate and characterize hybrid oriented and nanostructured thin films composed of a semiconducting polymer, regioregular poly(3-hexylthiophène) (P3HT) and semiconducting CdSe nanocrystals (spheres, rods). Two orientation methods were used: directional epitaxial crystallization and mechanical rubbing. Epitaxied and rubbedfilms of pure P3HT show strong differences in terms of nanomorphology, crystalline order and structure. Epitaxied films possess a lamellar morphology, a 3D crystalline order and fiber symmetry where the P3HT backbones (cP3HT) are aligned along the fiber axis. Rubbed films do not show a lamellar morphology and have a 2D crystalline order with crystalline domains preferentially oriented “flat-on” relative to the substrate. These differences are reflected in the optical properties of the films. The orientation degree achieved in rubbed films strongly depends on the molecular weight of the polymer. There is also a strong anisotropy of the charge transport properties. Regarding hybrid epitaxied layers, we observed a nanostructuration with a localization of the CdSe nanocrystals into the amorphous zones of the P3HT. Moreover, electron tomography analysis shows that such films have a bilayer structure with a hybrid layer covered by pure P3HT. In rubbed hybrid films prepared with nanorods, the long axis of the nanorods as well as the P3HT backbone are oriented parallel tothe rubbing direction. The degree of in-plane orientation of the rods and of the P3HT matrix match closely and depend on the proportion of CdSe nanrods in the films. These results suggest that the P3HT matrix enforces the orientation of the rods.