Spelling suggestions: "subject:"porousmedia"" "subject:"porousmedium""
141 |
Transient Model of Heat,Mass,and Charge transfer as well as Electrochemistry in the Cathode Catalyst Layer of a PEMFCGenevey, Daniel Bruno 20 December 2001 (has links)
A transient model of the cathode catalyst layer of a proton exchange membrane fuel cell is presented. The catalyst layer structure can be described as a superposition of the polymer membrane, the backing layer, and some additional platinum particles. The model, which incorporates some of the features of the pseudo-homogeneous models currently present in the literature, considers the kinetics of the electrochemical reaction taking place at the platinum surface, the proton transport through the polymer agglomerates, and the oxygen and water transport within the pores as well as the membrane material of the catalyst layer. Due to the lower porosity of this region and the higher liquid water content, the catalyst layer can be current limiting in the fuel cell. Furthermore, since the cost of the catalyst material is critical, it is important to have a model predicting the effective utilization of this catalyst layer as well as one, which gives insights into how it might be improved.
Equations are presented for the mass conservation of reactants and products, the electrical and ionic currents, and the conservation of energy. A discussion of a number of the closure relations such as the Butler-Volmer equation employed is included as is a discussion of the initial and boundary conditions applied. The mathematical model is solved using a finite elements approach developed at the I.U.S.T.I. / Master of Science
|
142 |
Sustainable acoustic and thermal insulation materials from elastomeric waste residuesBenkreira, Hadj, Khan, Amir, Horoshenkov, Kirill V. 07 June 2011 (has links)
No / This study presents the data elements to develop a new processing route to transform elastomeric waste residue (particulates) into acoustic and thermal insulation materials that can compete with commercial products. The approach is to bind these grain and fibre particulates with a foaming polyurethane or a similar polymer, the chemistry of which can be manipulated to control the structure stiffness and the evolution of the foaming gas into open or closed cells. Here the study uses two examples of such residues, tyre and carpet shreds both composed of fibres trapping grains of either rubber or PVC. Compounds were made from these systems with different PU binders and the structural properties (density, porosity, air flow resistivity, tortuosity and stiffness) and performance properties (sound absorption, sound transmission, impact sound insulation and thermal conductivity) were measured as a function of binder loading and chemistry. The data obtained show clearly that performance can be tailored by tailoring structural properties resulting with materials that match or even outperform commercial products. The data set obtained here can be usefully exploited with available acoustic and thermal insulation materials model to take the approach further and extended to other waste systems.
|
143 |
Characterization of nanoparticle transport in flow through permeable mediaMetin, Cigdem 19 November 2013 (has links)
An aqueous nanoparticle dispersion is a complex fluid whose mobility in porous media is controlled by four key factors: the conditions necessary for the stability of nanoparticle dispersions, the kinetics of nanoparticle aggregation in an unstable suspension, the rheology of stable or unstable suspensions, and the interactions between the nanoparticles and oil/water interface and mineral surfaces. The challenges in controlling nanoparticle transport come from the variations of pH and ionic strength of brine, the presence of stationary and mobile phases (minerals, oil, water and gas), the geochemical complexity of reservoir rocks, and pore-network.
The overall objective of this work is to achieve a better understanding of nanoparticle transport in porous media based on a systematic experimental and theoretical study of above factors. For this purpose, the critical conditions for the aqueous stability of nanoparticles are identified and fit by a theoretical model, which describes the interaction energy between silica nanoparticles. Above critical conditions nanoparticle aggregation becomes significant. A model for the aggregation kinetics is developed and validated by experiments.
A mechanistic model for predicting the viscosity of stable and unstable silica nanoparticle dispersions over a wide range of solid volume fraction is developed. This model is based on the concept of effective maximum packing fraction.
Adsorption experiments with silica nanoparticles onto quartz, calcite and clay surfaces and interfacial tension measurements provide insightful information on the interaction of the nanoparticles with minerals and decane/water interface. The extent of nanoparticle adsorption on mineral/water and decane/water interfaces is evaluated based on DLVO theory and Gibbs’ equation. Visual observations and analytical methods are used to understand the interaction of nanoparticles with clay.
The characterization of nanoparticle behavior in bulk phases is built into an understanding of nanoparticle transport in porous media. In particular, the rheology of nanoparticle dispersions flowing through permeable media is compared with those determined using a rheometer. In the presence of residual oil, the retention of silica nanoparticles at water/oil interface during steady flow is investigated. The results from batch experiments of nanoparticle adsorption are used to explain the flow behavior of these nanoparticles in a glass bead pack at residual oil saturation. / text
|
144 |
Multi-scale Modeling of Nanoparticle Transport in Porous Media : Pore Scale to Darcy ScaleSeetha, N January 2015 (has links) (PDF)
Accurate prediction of colloid deposition rates in porous media is essential in several applications. These include natural filtration of pathogenic microorganisms such as bacteria, viruses, and protozoa, transport and fate of colloid-associated transport of contaminants, deep bed and river bank filtration for water treatment, fate and transport of engineered nanoparticles released into the environment, and bioremediation of contaminated sites. Colloid transport in porous media is a multi-scale problem, with length scales spanning from the sub-pore scale, where the particle-soil interaction forces control the deposition, up to the Darcy scale, where the macroscopic equations governing particle transport are formulated. Colloid retention at the Darcy scale is due to the lumped effect of processes occurring at the pore scale. This requires the incorporation of the micro-scale physics into macroscopic models for a better understanding of colloid deposition in porous media. That can be achieved through pore-scale modeling and the subsequent upscaling to the Darcy scale. Colloid Filtration Theory (CFT), the most commonly used approach to describe colloid attachment onto the soil grains in the subsurface, is found to accurately predict the deposition rates of micron-sized particles under favorable conditions for deposition. But, CFT has been found to over predict particle deposition rates at low flow velocity conditions, typical of groundwater flow, and for nanoscale particles. Also, CFT is found to be inapplicable at typical environmental conditions, where conditions become unfavorable for deposition, due to factors not considered in CFT such as deposition in the secondary minimum of the interaction energy profile, grain surface roughness, surface charge heterogeneity of grains and colloids, and deposition at grain-to-grain contacts. To the best of our knowledge, mechanistic-based models for predicting colloid deposition rates under unfavorable conditions do not exist. Currently, fitting the colloid breakthrough curve (BTC), obtained from the laboratory column-or field-scale experiments, to the advection-dispersion-deposition model is used to estimate the values of deposition rate coefficients. Because of their small size (less than 100 nm), nanoparticles, a sub-class of colloids, may interact with the porous medium in a different way as compared to the larger colloids, resulting in different retention mechanisms for nanoparticles and micron-sized particles. This emphasizes the need to study nanoparticles separately from larger, micrometer-sized colloids to better understand nanoparticle retention mechanisms.
The work reported in this thesis contributes towards developing mathematical models to predict nanoparticle movement in porous media. A comprehensive mechanistic approach is employed by integrating pore-scale processes into Darcy-scale models through pore-network modeling to upscale nanoparticle transport in saturated porous media to the Darcy scale, and to develop correlation equations for the Darcy-scale deposition parameters in terms of various measurable parameters at Darcy scale. Further, a one-dimensional mathematical model to simulate the co-transport of viruses and colloids in partially saturated porous media is developed to understand the relative importance of various interactions on virus transport in porous media.
Pore-network modeling offers a valuable upscaling tool to express the macroscopic behavior by accounting for the relevant physics at the underlying pore scale. This is done by idealizing the pore space as an interconnected network of pore elements of different sizes and variably connected to each other, and simulating flow and transport through the network of pores, with the relevant physics implemented on a pore to pore basis (Raoof, 2011). By comparing the results of pore-network modeling with an appropriate mathematical model describing the macro-scale behavior, a relationship between the properties at the macro scale and those at the pore scale can be obtained. A three dimensional multi-directional pore-network model, PoreFlow, developed by Raoof et al. (2010, 2013) is employed in this thesis, which represents the porous medium as an interconnected network of cylindrical pore throats and spherical pore bodies, to upscale nanoparticle transport from pore scale to the Darcy scale. The first step in this procedure is to obtain relationships between adsorbed mass and aqueous mass for a single pore. A mathematical model is developed to simulate nanoparticle transport in a saturated cylindrical pore by solving the full transport equation, considering various processes such as advection, diffusion, hydrodynamic wall effects, and nanoparticle-collector surface interactions. The pore space is divided into three different regions: bulk, diffusion and potential regions, based on the dominant processes acting in each of these regions. In both bulk and diffusion regions, nanoparticle transport is governed by advection and diffusion. However, in the diffusion region, the diffusion is significantly reduced due to hydrodynamic wall effects. Nanoparticle-collector interaction forces dominate the transport in the potential region where deposition occurs. A sensitivity analysis of the model indicates that nanoparticle transport and deposition in a pore is significantly affected by various pore-scale parameters such as the nanoparticle and collector surface potentials, ionic strength of the solution, flow velocity, pore radius, and nanoparticle radius. The model is found to be more sensitive to all parameters under favorable conditions. It is found that the secondary minimum plays an important role in the deposition of small as well as large nanoparticles, and its contribution is found to increase as the favorability of the surface for adsorption decreases.
Correlation equations for average deposition rate coefficients of nanoparticles in a saturated cylindrical pore under unfavorable conditions are developed as a function of nine pore-scale parameters: the pore radius, nanoparticle radius, mean flow velocity, solution ionic strength, viscosity, temperature, solution dielectric constant, and nanoparticle and collector surface potentials. Advection-diffusion equations for nanoparticle transport are prescribed for the bulk and diffusion regions, while the interaction between the diffusion and potential regions is included as a boundary condition. This interaction is modeled as a first-order reversible kinetic adsorption. The expressions for the mass transfer rate coefficients between the diffusion and the potential regions are derived in terms of the interaction energy profile between the nanoparticle and the collector. The resulting equations are solved numerically for a range of values of pore-scale parameters. The nanoparticle concentration profile obtained for the cylindrical pore is averaged over a moving averaging volume within the pore in order to get the 1-D concentration field. The latter is fitted to the 1-D advection-dispersion equation with an equilibrium or kinetic adsorption model to determine the values of the average deposition rate coefficients. Pore-scale simulations are performed for three values of Péclet number, Pe = 0.05, 5 and 50. It is found that under unfavorable conditions, the nanoparticle deposition at pore scale is best described by an equilibrium model at low Péclet numbers (Pe = 0.05), and by a kinetic model at high Péclet numbers (Pe = 50). But, at an intermediate Pe (e.g., near Pe = 5), both equilibrium and kinetic models fit the 1-D concentration field. Correlation equations for the pore-averaged nanoparticle deposition rate coefficients under unfavorable conditions are derived by performing a multiple-linear regression analysis between the estimated deposition rate coefficients for a single pore and various pore-scale parameters. The correlation equations, which follow a power law relationship with nine pore-scale parameters, are found to be consistent with the column-scale and pore-scale experimental results, and qualitatively agree with CFT.
Nanoparticle transport is upscaled from pore to the Darcy scale in saturated porous media by incorporating the correlations equations for the pore-averaged deposition rate coefficients of nanoparticles in a cylindrical pore into a multi-directional pore-network model, PoreFlow (Raoof et al., 2013). Pore-network model simulations are performed for a range of parameter values, and nanoparticle BTCs are obtained from the pore-network model. Those curves are then modeled using 1-D advection-dispersion equation with a two-site first-order reversible deposition, with terms accounting for both equilibrium and kinetic sorption. Kinetic sorption is found to become important as the favorability of the surface for deposition decreases. Correlation equations for the Darcy¬scale deposition rate coefficients under unfavorable conditions are developed as a function of various measurable Darcy-scale parameters, including: porosity, mean pore throat radius, mean pore water velocity, nanoparticle radius, ionic strength, dielectric constant, viscosity, temperature, and surface potentials on the nanoparticle and grain surface. The correlation equations are found to be consistent with the observed trends from the column experiments available in the literature, and are in agreement with CFT for all parameters, except for the mean pore water velocity and nanoparticle radius. The Darcy-scale correlation equations contain multipliers whose values for a given set of experimental conditions need to be determined by comparing the values of the deposition rate coefficients predicted by the correlation equations against the estimated values of Darcy-scale deposition parameters obtained by fitting the BTCs from column or field experiments with 1-D advection-dispersion-deposition model. They account for the effect of factors not considered in this study, such as the physical and chemical heterogeneity of the grain surface and nanoparticles, flow stagnation points, grain-to-grain contacts, etc.
Colloids are abundant in the subsurface and have been observed to interact with a variety of contaminants, including viruses, thereby significantly influencing their transport. A mathematical model is developed to simulate the co-transport of viruses and colloids in partially saturated porous media under steady state flow conditions. The virus attachment to the mobile and immobile colloids is described using a linear reversible kinetic model. It is assumed that colloid transport is not affected by the presence of attached viruses on its surface, and hence, colloid transport is decoupled from virus transport. The governing equations are solved numerically using an alternating three-step operator splitting approach. The model is verified by fitting three sets of experimental data published in the literature: (1) Syngouna and Chrysikopoulos (2013) and (2) Walshe et al. (2010), both on the co-transport of viruses and clay colloids under saturated conditions, and (3) Syngouna and Chrysikopoulos (2015) for the co-transport of viruses and clay colloids under unsaturated conditions. The model results are found to be in good agreement with the observed BTCs under both saturated and unsaturated conditions.
Then, the developed model was used to simulate the co-transport of viruses and colloids in porous media under unsaturated conditions, with the aim of understanding the relative importance of various processes on the co-transport of viruses and colloids. The virus retention in porous media in the presence of colloids is greater under unsaturated conditions as compared to the saturated conditions due to: (1) virus attachment to the air-water interface (AWI), and (2) co-deposition of colloids with attached viruses on its surface to the AWI. A sensitivity analysis of the model to various parameters showed that virus attachment to AWI is the most sensitive parameter affecting the BTCs of both free viruses and total mobile viruses, and has a significant effect on all parts of the BTC. The free and the total mobile virus BTCs are mainly influenced by parameters describing virus attachment to the AWI, virus interactions with mobile and immobile colloids, virus attachment to solid-water interface (SWI), and colloid interactions with SWI and AWI. The virus BTC is relatively insensitive to parameters describing the maximum adsorption capacity of the AWI for colloids, inlet colloid concentration, virus detachment rate coefficient from the SWI, maximum adsorption capacity of the AWI for viruses, and inlet virus concentration.
|
145 |
Flow/acoustic interactions in porous media under a turbulent wind environmentXu, Ying January 1900 (has links)
Doctor of Philosophy / Department of Mechanical and Nuclear Engineering / Zhongquan Zheng / Windscreens are widely used in outdoor microphone measurement for acoustic sensing systems. In many cases of outdoor microphone applications, wind noise interferes with the signals. The performance of measurement microphones thus heavily depends on correct designs of windscreens that are used to maximize the signal to noise ratio of the sensing system. The purpose of the study is to investigate the wind noise reduction between the unscreened microphone and the screened microphone under different frequencies of incoming wind turbulence.
In this study, a modified immersed boundary method using the distributed forcing term has been applied to simulate the flow/acoustic interaction between air and the porous medium. Because of the high accuracy requirement in the vicinity of the interface between air and the porous medium, spatial derivatives of flux need to be discretized using high order schemes. In this study, several different schemes have been tested in the vicinity of the interface including a second-order upwind scheme, a third-order upwind scheme, and a fifth-order Weighted Essentially Non-Oscillatory (WENO) scheme. Based on the test results, the fifth-order WENO scheme is selected for most of the simulation cases. The model equations for flow outside the windscreen are the Navier-Stokes equations; flow inside the windscreen (porous medium) uses the modified Zwikker-Kosten equation.
The wind turbulence in this study is generated by two different ways. The first is to place different sizes of solid cylinders and spheres in the upstream of the microphone under two-dimensional and three-dimensional conditions. The second is to use a Quasi-Wavelet method to generate the background atmospheric turbulence to simulate the real physical phenomena. Both two-dimensional and three-dimensional simulations for the flow over the unscreened and the screened microphone are presented and discussed under both low Reynolds number and high Reynolds number flow conditions.
The results show that the windscreen effect is significant and the wind noise reduction level between the unscreened and the screened microphone can reach around 20dB either for low Reynolds number cases or for high Reynolds number cases. For low Reynolds number cases, Low flow resistivity windscreens are more effective for low frequency turbulence; high flow resistivity windscreens are more effective for high frequency turbulence. For high Reynolds number cases, the medium flow resistivity windscreens perform better compared to low flow resistivity windscreens and high flow resistivity windscreens.
|
146 |
Microstructure et macro-comportement acoustique : approche par reconstruction d'une cellule élémentaire représentativePerrot, Camille January 2006 (has links)
The fundamental issue of determining acoustic properties of porous media from their local geometry is examined in this PhD dissertation thesis, thanks to a sample of open-cell aluminum foam analyzed by axial computed microtomography. Various geometric properties are measured to characterize the experimental sample at the cell size level. This is done in order to reconstruct a porous medium by means of idealized three- and two- dimensional unit-cells.The frequency dependant thermal and velocity fields governing the propagation and dissipation of acoustic waves through rigid porous media are computed by Brownian motion simulation and the finite element method, respectively. Macroscopic behavior is derived by spatial averaging of the local fields. Our results are compared to experimental data obtained from impedance tube measurements. Firstly, this approach leads to the identification of the macroscopic parameters involved in Pride and Lafarge semiphenomenological models. Secondly, it yields a direct access to thermal and viscous dynamic permeabilities. However, the bi-dimensional model underestimates the static viscous permeability as well as the viscous characteristic length; what thus require a three-dimensional implementation.
|
147 |
Image-Based Numerical Simulation of Stokes Flow in Porous MediaErdmann, Robert Gerald January 2006 (has links)
Numerical models for the simulation of longitudinal and transverse Stokes flow in cylindrical periodic porous media are presented. The models, which are based on a finite-volume formulation in primitive variables, utilize digital image representations of the geometries to simulate, making them particularly well-suited for the rapid automated analysis of creeping flow in porous media with complex morphologies. Complete details of the model formulations are given, including extensive treatment of the pressure boundary conditions at the solid-liquid interface needed to guarantee convergence with all possible geometries. The convergence behavior of both models is tested, and the models are shown to be second-order accurate.The models are used to simulate flow over the whole range of volume fractions of liquid in several regular geometries. The longitudinal model is used to simulate flow in square arrays of circular and square ducts, and both models are used to simulate flow in square and hexagonal arrays of circular cylinders and square arrays of square cylinders rotated by varying amounts. For each of the geometries, accurate empirical expressions for the Darcy permeability as a function of volume fraction solid are presented. Where applicable, model predictions of permeability are compared to existing analytical results.Subsequently, the models are used to simulate Stokes flow in random domains over a wide range of fractions liquid. The sequential random packing algorithm is used to generate 1,000 random packings of circular cylinders at each of 14 fractions of liquid, and longitudinal and transverse flow simulations are performed for each geometry. Histograms and summary statistics are computed for the permeability for each fraction liquid, and empirical expressions for mean permeability as a function of fraction liquid are given. The autocorrelation structure of the geometry and of the fluid velocity is analyzed, and an analysis of the scaling of longitudinal permeability variance is presented. In transverse flow at high packing densities, it is found that lightning-like patterns emerge in the fluid velocity. It is also found that the details of flows in such geometries are strongly sensitive to the placement of individual solid obstacles.
|
148 |
Fundamentals and Application of Porous Media Filtration for the Removal of Nanoparticles from Industrial WastewaterRottman, Jeffrey J. January 2012 (has links)
Increasing use of engineered nanomaterials presents concerns as some nanoparticles appear to be harmful to both human health and the environment. Effective treatment methods are required to remove problematic nanoparticles from (waste)water streams. Porous media filtration, commonly used for the removal of particulate matter, shows promise for nanoparticle treatment. The goal of this work is to investigate the potential of porous media filtration for the abatement of nanoparticles from aqueous waste streams. To this end, an automated method was developed that allows real-time and in-situ monitoring of nanoparticle transport and retention in porous media using online measurement of UV-visible absorbance or fluorescence. Development of fluorescent-core nano-silica (n-SiO₂) in controllable sizes provided an excellent tracer for nanoparticle transport in porous media. Measurement of n-SiO₂ by destructive techniques is complicated by high natural Si background levels. Fluorescence monitoring enables real-time measurement, facilitating rapid evaluation of n-SiO₂ transport. Synthesized n-SiO₂ remain in their primary sizes making an evaluation of the behavioral change of particles due to transition into the "nano" range possible. A comparison of the role of particle size on transport in porous media displayed the importance of particle number concentration as the dominance of site-specific adsorption may be obscured by simple mass concentration evaluation.T he effectiveness of different bed materials, namely, sand, activated carbon (AC), and diatomaceous earth (DE), for the removal of TiO₂ nanoparticles (n-TiO₂) from aqueous streams was investigated. DE proved promising for n-TiO₂ capture shown by its high bed capacity (33.8 mg TiO₂ g⁻¹(medium)) compared to AC (0.23 mg TiO₂ g⁻¹(medium)) or sand (0.004 mg TiO₂ g⁻¹(medium)). The presence of organic and synthetic contaminants produced varying effects on n-TiO₂ retention, mostly due to either enhanced electrostatic or steric interactions. Application of a process simulator combining physical straining with site-specific interactions, delineating physisorption from chemisorption and diffusion limited interactions, enabled the accurate fit of n-TiO₂ transport in sand, AC and DE. The fitting process revealed the advantage of DE due to increased physisorption and physical straining of n-TiO₂. Modeling of this system afforded the elucidation of controlling retention mechanisms and provides a basis for future scaling and system design.
|
149 |
Contributions to micromechanical modelling of transport and freezing phenomena within unsaturated porous mediaYang, Rong Wei, Yang, Rong Wei 23 September 2013 (has links) (PDF)
Micromechanical approach is employed to investigate the transport and freezing within unsaturated porous media. In unsaturated porous media, water film as well as disjoining pressure are introduced in the transport and freezing problems. In the modeling, it is found that, capillary layer along with pore water dominate the transport at high saturation degree (Sr>10%). However, water film will play a significant role in transport at low saturation degree (Sr<10%), and the diffusion coefficient will be lower than 3 to 4 orders of magnitude than that at higher saturation degree. A micromechanical model of freezing in unsaturated porous media is established. Micromechanical model of freezing is more physical based in nature. That is because different from poromechanical model of freezing media in which ice crystal pressure is introduced, the disjoining pressure of unfrozen water film instead of ice crystal pressure is introduced in the micromechanical model of freezing
|
150 |
Numerical modelling of nonwoven thermal bonding process & machineryPeksen, Murat January 2008 (has links)
Nonwoven-fabrics have been in use since 1930s. Their advantages over other web fonnation methods like knitting and weaving have attracted many industries such as aerospace, automotive, sports, geotextiles, composites, battery separators etc. to explore and increase their usage. During nonwoven manufacturing, most of the laid loose webs have an insufficient strength as fonned, and require an additional bonding procedure in order to provide the produced nonwoven with its intended properties. To achieve the desired properties of the nonwoven web, the bonding process is therefore, the most important part during production. The thennal bonding through air is one of the modem techniques which is incrementally improved to increase the yield of manufactured nonwoven properties. The system has a disadvantage which is, that the production capacity and energy efficiency is very low. The entitled research aims an industrial optimisation of the thermal bonding through air by entailing a strategic approach and encompassing the whole process chain of the thennal bonding process. The comprehensive and flexible optimisation opportunities provided by the CFD has been used to aid in the control and optimisation of the thermal bonding process and machinery. To optimise the process and product quality, the complex system composing of several components and various physical phenomena occurring during processing is simulated using a hierarchical methodology. More specifically a hierarchical decomposition procedure to recast the original multi scale problem as a sequence of three scale decoupled macro-, meso-, and micro scale subproblems is exploited. The methodology is applied in conjunction with the validation of experiments on through-air bonding product lines. 2D and 3D computational fluid dynamics (CFD) models based on the continuum modelling approach and the theory of porous media coupled with the theory of mixtures are developed to treat the flow behavior, heat transfer, phase change and air moisture transport within the whole through-air bonding system. The model is concluded to be an economic computational tool hence providing rapid process optimisation and valuable infonnation early in the process, which can replace costly experiments and ensure product consistency under variable process and climate conditions. 2D and 3D hybrid modelling considering parametric discrete and continuum parts is also perfonned using conjugate heat transfer analyses. The approach precisely permits the optimisation of the machine component design and the associated optimisation of consistent process and product properties.
|
Page generated in 0.0359 seconds