In this thesis the integration of photovolatic (PV) generation and energy storage into the electrical grid is discussed. Although the studied system is for grid tied applications, here the integration of the PV generation and the energy storage system (ESS) on the DC-side of the system is addressed. The work contained in this thesis focuses on the integration of the DC-working parts before interfacing them with the grid through the use of an inverter and seeks an increasing in the energy that the system can deliver.First, a study of classical systems that present well-differentiated parts is presented: PV generation, a lithium-ion battery based ESS, the utility grid and a residential electricity consumer. PV installations of 3 and 10kWp are considered together with storage capacities ranging from 1 to 9kWh. This yields interesting insights on how the system works based on the timing of the generation and consumption of energy. The results are used to highlight the weaknesses of the selected converter arrangement for the interfacing of the PV source and the ESS. Results show that the system is rather stiff and lacks from conversion efficiency when it needs to work in a wide range of powers, mainly due to low consumer power demand during battery discharge. In this first part of the thesis, three solutions to workaround the efficiency problem are proposed: reducing the difference between the ESS and the DC-bus voltages, using isolated converters to interface the ESS, or adopting a new arrangement of the parts of the system. One of the first two proposed solutions should be adopted if the same system topology is to be kept. These two solutions address the efficiency problem when the ESS is involved in the energy conversion. The third solution is proposed as alternative to the classical systems that use a DC-bus to exchange power with the different parts of the system. The new proposed arrangement features a distributed maximum power point (DMPPT) type system that includes storage at module level. DMPPT systems are able to track the maximum power point (MPPT) of each panel separately by connecting a small power electronic converter (PEC) to each PV panel. They are specially useful when the PV installation receives uneven irradiance, i.e. shadows are present in some of the panels, increasing the annual yield of PV energy from 7 to 30% as reported in the literature. Unfortunately, this kind of systems cannot always handle high irradiance mismatches, and fail to track the maximum power point (MPP) throughout the whole installation in some cases. Including batteries at module level instead of connecting them to the DC-bus, allows for increasing the MPPT range of the system, virtually to any severity of irradiance mismatch (depending on the state of charge (SoC) of the battery pack), as well as adding storage capability to the system. The novel proposed system is able to workaround the problems of using non-isolated converters, achieving PV energy conversion efficiencies from 86% (for at least 10% of the peak power) to 90% and storage charge/discharge efficiencies ranging from 86% to 95%. Besides, it brings the opportunity to exploit the synergies of having storage at module level in systems that combine renewable energies and storage. Moreover, DMPPT systems achieve superior PV generation under partially shaded conditions when compared to classical PV arrays increasing the PV generation when compared to classical or centralized PV installations up to 45% in power as reported in the literature.In the second part of the thesis, the proposed novel DMPPT topology is presented. The whole system is fully designed from scratch, including PECs, sizing of the different parts of the modules, embedded control loops of the modules and supervisory control of the whole system. Finally, the results obtained from running the proposed system are shown and discussed, and suggestions given on how to operate and protect the system. Experimental results are obtained using a 1.5kWp PV power and 1.5kWh capacity test bench built for that purpose.The proposed system is able to generate PV energy, store the energy coming from PV generation and inject the generated and stored energy into the grid. The proposed system extends the MPPT capability of storage-less series-connected DMPPT systems. This is achieved by using the batteries not only to store energy when required, but also to compensate the power mismatch across DMPPT modules of the same string when the output voltage of the modules becomes a limit. It also presents a modular and upgradable approach to PV systems including storage. This modularity also brings fault tolerance, and an ability to continue working after failure of one or more of the DMPPT modules by partially or completely isolating the faulty module (depending on the nature of the fault). Moreover, the addition of the DC-DC converters allows for the use of different PV panels in the system, i.e. from different manufacturers or technologies.In conclusion, the presented system is very flexible, can be designed for a wide range of power levels and energy storage sizes, and presents improved reliability when compared to other series-connected DMPPT systems. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished

Este trabalho propÃe o desenvolvimento de uma fonte de alimentaÃÃo portÃtil para notebooks e outros equipamentos eletrÃnicos usando energia fotovoltaica. O sistema completo à composto por dois mÃdulos fotovoltaicos poli-cristalinos de 54W conectados em paralelo; um conversor boost clÃssico usado para controlar a carga das baterias de chumbo-Ãcido reguladas a vÃlvula (VRLA-Valve Regulated Lead Acid) de 40 Ah associadas em sÃrie formando um barramento de 24Vcc e um conversor boost-flyback que tem a funÃÃo de elevar a tensÃo do banco de baterias de 24Vcc a uma tensÃo de saÃda de 250Vcc. O conversor boost utiliza o algoritmo perturba e observa (P&O) para conseguir o ponto de mÃxima potÃncia dos mÃdulos fotovoltaicos. Por outro lado, no conversor boost-flyback que opera em modo de conduÃÃo contÃnua (MCC) à usada a tÃcnica de controle por corrente de pico. Para verificar o princÃpio de funcionamento da fonte de alimentaÃÃo de dois estÃgios, o primeiro estÃgio foi desenvolvido com potÃncia de saÃda de 120W e o segundo estÃgio com potÃncia de saÃda de 200W. / This study proposes the development of a portable power supply to feed notebook computers and other electronic equipment using photovoltaic energy. The complete system is composed by two polycrystalline photovoltaic modules of 54W in parallel, a classic boost converter that allows to work the photovoltaic modules in the maximum power point (MPP) and to charge two lead-acid valve regulated batteries (VRLA Valve-Regulated Lead Acid) of 40Ah associates in series to form a bus of 24Vcc, and a boost-flyback converter that has as function to raise the battery bank voltage of 24Vcc to output voltage of 250Vcc. The boost converter uses the algorithm perturb and observe (P&O) to track the maximum power point of the photovoltaic modules. On the other hand, in the boost-flyback converter operates in continuous conduction mode (CCM) using peak current mode control technique to regulate the output voltage. To verify the feasibility of the two stage power supply, was developed a prototype with first stage of 120W output power, and the second stage of 200W output power.

Photovoltaic installations in urban areas operate under uneven lighting conditions. For such a system to achieve its peak efficiency, each solar panel is connected in series through a micro-converter, a dc-dc converter that performs per-panel distributed maximum power point tracking (DMPPT). The objective of this thesis is to design a compensator for the DMPPT micro-converter. A novel, systematic approach to plant modeling is presented for this system, together with a framework for characterizing the plant’s uncertainty. A robust control design procedure based on linear matrix inequalities is then proposed, which ensures robust performance and stability of the time-varying system. The proposed modeling and control design methods are demonstrated for an example rooftop photovoltaic installation. The system and the designed compensator are tested in simulations. Simulation results show satisfactory performance over a range of operating conditions, and the simulated system is shown to track the maximum power point of every panel.

Photovoltaic installations in urban areas operate under uneven lighting conditions. For such a system to achieve its peak efficiency, each solar panel is connected in series through a micro-converter, a dc-dc converter that performs per-panel distributed maximum power point tracking (DMPPT). The objective of this thesis is to design a compensator for the DMPPT micro-converter. A novel, systematic approach to plant modeling is presented for this system, together with a framework for characterizing the plant’s uncertainty. A robust control design procedure based on linear matrix inequalities is then proposed, which ensures robust performance and stability of the time-varying system. The proposed modeling and control design methods are demonstrated for an example rooftop photovoltaic installation. The system and the designed compensator are tested in simulations. Simulation results show satisfactory performance over a range of operating conditions, and the simulated system is shown to track the maximum power point of every panel.

The wind turbine generation system (WTGS) exhibits a nonlinear characteristic and its maximum power point varies with changing atmospheric conditions. In order to operate the WTGS at maximum power output under various wind speeds and to avoid using speed encoder in practical applications, it is necessary to improve the controller system to operate the maximum power points in the WTGS. There are three factors to influence wind generator, the wind speed, power coefficient and the radius of blade. The power coefficient depends on the blade pitch angle and tip speed ratio (TSR). The objective of the dissertation is to develop an intelligent controlled wind energy conversion system (WECS) using AC/DC and DC/AC power converters for grid-connected power application. To achieve a fast and stable response for the real power control, an intelligent controller was proposed, which consists of a fuzzy neural network (FNN), a recurrent fuzzy neural network (RFNN), a wilcoxcon radial basis function network (WRBFN) and a improved Elman neural network (IENN) for MPPT. Furthermore, the parameter of the developed FNN, RFNN, WRBFN and IENN are trained on-line using back-propagation learning algorithm. However, the learning rates in the FNN, RFNN, WRBFN, and IENN are usually selected by trial and error method, which is time-consuming. Therefore, modified particle swarm optimization (MPSO) method is adopted to adjust the learning rates to improve the learning capability of the developed RFNN, WRBFN and IENN. Moreover, presents the estimation of the rotor speed is based on the sliding mode and model reference adaptive system (MRAS) speed observer theory. Furthermore, a sensorless vector-control strategy for an induction generator (IG) operating in a grid-connected variable speed wind energy conversion system can be achieved. On the other hand, a WRBFN based with hill-climb searching (HCS) maximum-power-point-tracking (MPPT) strategy is proposed for permanent magnet synchronous generator (PMSG) with a variable speed wind turbine. Finally, many simulation results are provided to show the effectiveness of the proposed intelligent control wind generation systems.

The declining cost of photovoltaic (PV) modules has enabled the vision of ubiquitous photovoltaic (PV) power to become feasible. Emerging PV technologies are facilitating the creation of intentionally non-flat PV modules, which create new applications for this sustainable energy generation currently not possible with the traditional rigid, flat silicon-glass modules. However, since the photovoltaic cells are no longer coplanar, there are significant new requirements for the power electronics necessary to convert the native form of electricity into a usable form and ensure maximum energy harvest. Non-uniform insolation from cell-to-cell gives rise to non-uniform current density in the PV material, which limits the ability to create series-connected cells without bypass diode or other ways to shunt current, which is well known in the maximum power tracking literature. This thesis presents a modeling approach to determine and quantify the variations in generation of energy due to intentionally non-flat PV geometries. This will enable the power electronics circuitry to be optimized to harvest maximum energy from PV pixel elements – clusters of PV cells with similar operating characteristics. This thesis systematically compares different geometries with identical two-dimensional projection "footprints" for energy harvest throughout the day. The results show that for the same footprint, a semi-cylindrical surface harvests more energy over a typical day than a flat plate. The modeling approach is then extended to demonstrate that by using non flat geometries for PV panel, the availability of a remotely located stand-alone power system can be increased when compared to a flat panel of same footprint. These results have broad application to a variety of energy scavenging scenarios in which either total energy harvested needs to be maximized or unusual geometries for the PV active surfaces are required, including building-integrated PV. This thesis develops the analysis of the potential energy harvest gain for advanced non-planar PV collectors as a necessary first step towards the design of the power electronics circuits and control algorithms to take advantage of the new opportunities of conformal and non-flat PV collectors.

Σκοπός της συγκεκριμένης διπλωματικής εργασίας είναι η εξομοίωση ενός φωτοβολταϊκού συστήματος διασυνδεδεμένου στο τριφασικό δίκτυο με σκοπό τη μελέτη της λειτουργίας του και του καλύτερου σχεδιασμού του. Το σύστημα περιλαμβάνει τη φωτοβολταϊκή γεννήτρια, ένα φίλτρο διασύνδεσης της γεννήτριας με τον αντιστροφέα και ένα απλοποιημένο μοντέλο του τριφασικού συστήματος. Για την εξομοίωση του κυκλώματος το οποίο είναι χρονικά μεταβαλλόμενο λόγω της διακοπτικής λειτουργίας του μετατροπέα αναπτύσσεται μια συστηματική και αποτελεσματική μέθοδος για την ανάλυση κυκλωμάτων που περιέχουν e-R-L, C κλάδους και ιδανικούς διακόπτες. Χρησιμοποιώντας την τοπολογία του κυκλώματος και κατάλληλες μήτρες μετασχηματισμού οι εξισώσεις που περιγράφουν το αγώγιμο και μη αγώγιμο τμήμα του κυκλώματος προκύπτουν αυτόματα. Οι χρησιμοποιούμενες μήτρες μετασχηματισμού προκύπτουν με απλό και συστηματικό τρόπο από τις θεμελιώδης μήτρες του κυκλώματος. Σε κάθε βήμα προκύπτουν τα ρεύματα όλων των κλάδων του κυκλώματος από την επίλυση του αγώγιμου τμήματος αυτού και οι τάσεις των βαλβίδων που δεν άγουν από την επίλυση του μη αγώγιμου τμήματός του. Η μέθοδος είναι γενική και μπορεί να εφαρμοστεί για την μελέτη τυχόντων σφαλμάτων σε οποιοδήποτε τμήμα του κυκλώματος. Παρουσιάζονται τα αποτελέσματα της εξομοίωσης για λειτουργία του μετατροπέα ως ανορθωτή, ως αντιστροφέα, ως αντιστροφέα με φωτοβολταϊκή γεννήτρια και ως αντιστροφέα με φωτοβολταϊκή γεννήτρια και με ανιχνευτή σημείου μέγιστης ισχύος. Το χρησιμοποιηθέν μοντέλο θα μπορούσε να βελτιωθεί αν στην θέση του τριφασικού συστήματος χρησιμοποιηθεί ακριβέστερη αναπαράσταση του τριφασικού δικτύου στην οποία να περιλαμβάνεται και ο τριφασικός μετασχηματιστής ισχύος που διασυνδέει το φωτοβολταϊκό σύστημα με το AC δίκτυο. / The objective of this “Diploma Thesis” is the simulation of a grid connected photovoltaic (PV) system and the study of its operation. The system consists of a PV generator, a DC filter and a simplified model of the three-phase system. The method which was used for the simulation of the circuit (which is a varying topology circuit due to the switching operation of the converter) is a systematic, efficient and conceptually simple method for the analysis of circuits consisting of linear e, R, L, C elements and ideal switches. On the basis of well known network topological concepts a suitable transformation tensor is constructed at every step. This tensor constitutes a flexible and powerful tool to assemble automatically the necessary on-switch current and off-switch voltage equations required for any conduction pattern. The method is general and can be applied for the study of any random faults in any part of the circuit. Results of the simulation for operation of the converter as rectifier, as inverter with battery, as inverter with PV generator and as inverter with PV generator and with MPPT are presented. The used model could be improved if the three-phase system is more precisely represented by a power three-phase transformer which connects the PV system with the AC network.

This thesis deals with quantifying the merits of Distributed Maximum Power Point Tracking (DMPPT), as well as providing solutions to achieve DMPPT in PV systems. A general method based on 3D modeling is developed to determine the energy yield of PV installations exploiting different levels of DMPPT granularity. Sub-string-level DMPPT is shown to have up to 30% more annual energy yield than panel-level DMPPT. A Multi-Input-Single-Output (MISO) dc-dc converter is proposed to achieve DMPPT in parallel-connected applications. A digital current-mode controller is used to operate the MISO converter in pseudo-CCM mode. For series-connected applications, the virtualparallel concept is introduced to utilize the robustness of the parallel connection. This concept is demonstrated on a three-phase boost converter. The topology offers reduced output voltage ripple under shading which increases the life-time of the output capacitor. The prototypes yield output power benefits of up to 46% and 20% for the tested shading conditions.

Neste trabalho apresenta-se o modelo de um controlador baseado em Lógica Fuzzy para um sistema de energia baseado em fonte renovável solar fotovoltaica (photovoltaic - PV) multi-string em operação isolada, para o aproveitamento da máxima potência desta fonte. O sistema é composto por painéis solares, conversor CC-CC tipo elevador de tensão (boost), armazenamento por banco de baterias, inversor trifásico e carga trifásica variável. O sistema fotovoltaico foi modelado no MATLAB/Simulink de forma a representar a curva característica V-I do módulo PV, e que é baseado nos dados disponíveis em data-sheets de painéis fotovoltaicos comerciais. Outros estudos de natureza elétrica tais como o cálculo dos valores eficazes das correntes no conversor CC-CC, para avaliação das perdas, indispensáveis para o dimensionamento de componentes eletrônicos, foram realizados. O método tradicional Perturb and Observe de rastreamento do ponto de máxima potência (Maximum Power Point Tracking MPPT) de painéis foi testado e comparado com métodos que usam a Lógica Fuzzy. Devido ao seu desempenho, foi adotado o método Fuzzy que realiza o MPPT por inferência do ciclo de trabalho de um modulador por largura de pulso (Pulse Width Modulation - PWM) através da variação da potência pela variação da corrente do painel solar. O modelo Fuzzy adotado neste trabalho foi testado com sucesso. Os resultados mostraram que ele pode ser robusto e atende à aplicação proposta. Segundo alguns testes realizados, este controlador pode realizar o MPPT de um sistema PV na configuração multi-string onde alguns arranjos fotovoltaicos são usados. Inclusive, este controle pode ser facilmente adaptado para realizar o MPPT de outras fontes de energia baseados no mesmo princípio de controle, como é o caso do aerogerador. / This work presents the model of a Fuzzy Logic controller for a renewable energy system based on multi-string solar photovoltaic (PV) in stand-alone operation, to extract the maximum energy of this power source. The system consists of PV modules, DC-DC converter (Boost), a battery set, three-phase inverter and three-phase variable load. The photovoltaic system was modeled in MATLAB / Simulink in order to represent the V-I characteristic of the PV module, and which is based on the data provided by the manufacturer data-sheet. Other studies, such as the calculation of the RMS currents of the DC-DC converter components for evaluation of the losses, which are essential for the system design were accomplished. The conventional Perturb and Observe method for the Maximum Power Point Tracking (MPPT) of PV modules was tested and compared with methods that use Fuzzy Logic control. Due to its performance, it was adopted the Fuzzy method that performs the MPPT by inference of duty cycle of a Pulse Width Modulation (PWM) through the variation of PV power divided by the variation of the PV current. The Fuzzy model considered in this work was successfully tested. The results showed that it can be robust and suitable to the proposed application. According to some accomplished tests, the controller can perform the MPPT of a multi-string configuration of the solar PV system, in which several PV arrays are used. Moreover, it can also be easily adapted to perform the MPPT of other energy power sources based on the same control principle, as it is in the case of aerogenerators.

Made available in DSpace on 2016-12-12T20:27:38Z (GMT). No. of bitstreams: 1 Rubens Hock.pdf: 9150198 bytes, checksum: dc75d13b884c75e842633257c0db27e6 (MD5) Previous issue date: 2015-02-24 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / This paper presents a mobile voltage regulator based in a Distribution Static Synchronous Compensator (DSTATCOM) applied to low voltage distribution grids. The DSTATCOM consists in a three-phase four-wire inverter connected to the grid through a second order low pass filter. The control structure is composed of three output voltage loops with active damping and the two dc bus loops. In addition, a new concept of Minimum Power Point Tracking (mPPT) is introduced, forcing the DSTATCOM to operate with the minimum power. In certain conditions, this means no compensation. The dynamic models of the converter are presented, as well as the control design. Simulation results show the capacity of voltage regulation and the features of the mPPT, even under grid and load unbalances and nonlinear loads. This work is concluded with the construction of a 30 kVA prototype and validation through experimental results proves the proper functioning of the voltage regulator. / Esse trabalho apresenta um regulador de tensão móvel baseado em um compensador estático de reativos (DSTATCOM) aplicado a redes de distribuição de baixa tensão. O DSTATCOM consiste em um inversor trifásico a quatro fios conectado à rede através de um filtro de segunda ordem. A estrutura de controle é composta por três malhas de tensão de saída com amortecimento ativo e duas malhas de tensão do barramento cc. Em adição, um novo conceito de rastreamento da mínima potência (mPPT) é introduzido, forçando o DSTATCOM a operar com a mínima potência. Em certas ocasiões, isso significa nenhuma compensação. Os modelos dinâmicos do conversor são apresentados, assim como o projeto de controle. Resultados de simulação mostram a capacidade de regulação da tensão e as características do mPPT, mesmo com desequilíbrios na rede e/ou na carga e com cargas não lineares. O trabalho é concluído com a construção de um protótipo de 30 kVA e validação dos estudos através de resultados experimentais obtidos comprovam o bom funcionamento do regulador de tensão.