Orientador: Mônica Pinto Barbosa / Banca: Tulio Nogueira Bittencourt / Banca: Rogério de Oliveira Rodrigues / Resumo: Apresenta-se como objeto desta pesquisa o estudo numérico não-linear da ductilidade de vigas de concreto armado convencional e de alto desempenho. Toda a análise numérica é efetuada no código de cálculo baseado no método dos elementos finitos CASTEM 2000, que utiliza o modelo reológico elastoplástico perfeito para o aço, o modelo de Drucker-Prager para o concreto e o método de Newton-Raphson para a solução de sistemas não-lineares. O núcleo deste trabalho concentra-se na obtenção de curvas força - deslocamento e momento - curvatura com a finalidade de quantificar respectivamente os índices de ductilidade global e local das vigas analisadas. De início, confrontam-se as respostas numéricas obtidas com resultados experimentais fornecidos pela literatura a fim de garantir confiabilidade à análise numérica realizada. Posteriormente, efetua-se a determinação da capacidade de deformação inelástica do elemento estrutural em questão, variando-se a resistência à compressão do concreto, a taxa geométrica de armadura longitudinal de tração, a tensão de escoamento das armaduras, o espaçamento entre estribos, a base da seção transversal do elemento estrutural e o efeito escala. Estes parâmetros foram avaliados para dois casos de solicitação: flexão simples tipo I e flexão simples tipo II. O primeiro caso caracteriza-se pela ação de forças simétricas aplicadas à 1/3 e 2/3 do vão e a segunda por uma força centrada no meio do vão. A linha de tendência geral observada foi de uma maior ductilização das vigas sujeitas à flexão simples tipo II, em detrimento às solicitadas por flexão simples tipo I. Quanto ao efeito escala observa-se que a ductilização das vigas é inversamente proporcional à esbeltez das mesmas. / Abstract: The objective of this thesis is the study of the ductility of high and conventional strength reinforced concrete beams by non-linear numerical simulations. The numerical analysis is based on the finite element method implemented in CASTEM 2000. This program uses the constitutive elastoplastic perfect model for the steel, the Drucker-Prager model for the concrete and the Newton-Raphson for the solution of non-linear systems. This work concentrates on the determination of force - displacement and moment - curvature curves with the purpose of quantifying the global and local ductility indexes of the beams. First, the numeric responses are confronted with experimental results found in the literature in order to check the reliability of the numerical analyses. Later, a parametric study is carried on. The inelastic deformation capacity of the structural element is investigated by varying the concrete compressive strength, the longitudinal reinforcement ratio, the yield stress of the reinforcement, the spacing between stirrups, the member section dimensions and the element size. These parameters have been analyzed for two cases: simple type I and simple type II bending. The first case is characterized by the action of applied symmetrical forces to the 1/3 and 2/3 of the beam size and second for a force centered in the middle of the beam size. The general tendency observed points to a high ductilization of the beams subjected to simple type II bending in comparison to the ones subjected to simple type I bending. With respect to the element size, it is noticed that the ductility of the beams is inversely proportional to their slendernesses. / Mestre

Muitas edificações têm apresentado degradação ao longo dos anos em todo o mundo, gerando situações de risco e causando acidentes, de modo que se têm estudado alternativas para se recuperar ou reforçar estruturalmente suas vigas, pilares e lajes. Entre as técnicas desenvolvidas para essas finalidades, destacam-se, atualmente, as que utilizam compósitos de polímeros reforçados com fibras (PRF), de modo que, desde as últimas décadas do século passado, desenvolveram-se os sistemas de reforço estrutural por colagem externa de tecidos e laminados de PRF de carbono (PRFC). Isto deve-se a este tipo de fibra apresentar o melhor conjunto de propriedades necessárias para se reforçarem as estruturas de concreto armado, como altas resistência à tração e módulo de elasticidade longitudinal. Na última década, surgiu o sistema de inserção de laminados de PRFC em entalhes executados no concreto de cobrimento de elementos estruturais preenchidos com resina epóxi. Embora haja resultados de outros pesquisadores, há a necessidade de maiores investigações no Brasil sobre o desempenho dessa nova técnica. Assim se propôs o planejamento experimental desta dissertação, cujo objetivo principal foi a análise experimental do desempenho de sistemas de reforço estrutural à flexão com laminados de PRFC aplicados a vigas de concreto armado ensaiadas com carregamento estático. De um total de dez vigas pré-moldadas, quatro foram testemunhos e seis foram reforçadas à flexão com dois laminados de PRFC através de três sistemas: colagem externa, inserção em entalhes longitudinais preenchidos com resina epóxi e com argamassa com sílica ativa. Analisa-se comparativamente o seu desempenho quanto às cargas máximas, aos deslocamentos verticais no centro do vão e às aberturas de fissuras. Constata-se que as reforçadas com laminados de PRFC inseridos em entalhes longitudinais preenchidos com resina epóxi apresentam os maiores valores de carga máxima e de rigidez. Entretanto as preenchidas com argamassa com sílica ativa obtêm desempenho inferior ao das vigas testemunhos por falta de aderência. Também se conclui que as reforçadas com colagem externa de laminados de PRFC têm os menores deslocamentos verticais no centro do vão. / Many buildings have shown deterioration over the years around the world, creating a hazardous situation and causing accidents, so that they have studied alternatives to recover or strengthen their structural beams, columns and slabs. Among the techniques developed for these purposes, stand out, currently, those using fiber reinforced polymer (FRP) composites. Since the last decades of the last century, it has been developed structural reinforcement systems of externally bonded carbon FRP (CFRP) textiles and laminates. This is due to the type of fiber having the best set of properties that are necessary to strengthen reinforced concrete structures, such as high tensile strength and longitudinal elastic modulus. In the last decade, the near-surface mounted CFRP laminates system executed in grooves in the concrete cover of structural elements filled with epoxy resin came up. Although there are results from other researchers, there is a need for further investigation in Brazil on the performance of this new technique. Thus, the experimental program of this thesis has been proposed, which main objective was the experimental analysis of the performance of bending structural reinforcement systems with CFRP laminates applied to reinforced concrete beams tested under static loading. From a total of ten precast beams, four were for control and six were strengthened in bending with two CFRP laminates composites through three systems: externally bonded, near-surface mounted insertion into longitudinal grooves filled with epoxy resin and mortar with silica fume. Their performance is comparatively analyzed for maximum loads, vertical displacements at mid-span and crack openings. It is concluded that those reinforced with near-surface mounted CFRP laminates inserted into longitudinal grooves filled with epoxy resin shows the highest maximum load and stiffness. However those filled with mortar with silica fume obtained lower performance than the control beams for lack of bonding. In addition, it is concluded that the ones strengthened with externally bonded CFRP laminates have the lowest mid-span vertical displacements.

Shear failure in concrete beams are often brittle in nature and potentially dangerous without adequatereinforcing measures. In design of concrete, it is commonly recommended to install transversalreinforcement along the shear span to induce a more ductile structural response, improving the shearcapacity all together and providing sufficient warning prior to collapse. However, it is more frequentlybeing assessed whether analogous performance can be achieved in fiber reinforced concrete beamswithout stirrups, and multiple attempts in literature confirm that it is possible. This alternative technologyintroduces need for better understanding of the modeling aspects of FRC in numerical simulations, as it isbecoming more common for engineers to resort to the finite element method in quality assurance ofstructures.In this thesis, the possibility of predicting shear failure numerically in simply supported fiber reinforcedconcrete beams with flexural bar reinforcement but without stirrups was investigated by means ofnonlinear finite element analysis, using the software package ATENA 2D Engineering. The ultimate aimwas to, as accurately as possible by means of numerical analyses on representative FE-models, replicatethe results from physical three-point-bending tests on simply supported FRC beams of various sizesperformed by Minelli et al. (2014). These beams were merely equipped with flexural reinforcement andexhibited shear failure.This thesis revolved around development and comparative assessment of material models for FRC basedon the smeared crack approach, adopting two different strategies: (1) The first strategy was to calibratematerial parameters based on results from 3PBT on notched FRC beams that were carried out prior totesting of the reinforced FRC beams, as reported by Minelli et al. (2014). Nonlinear finite element analysiswas used on representative FE-models for the notched 3PBT specimens, from which material parameterswere obtained iteratively by employing inverse analysis methods proposed by Červenka Consulting s.r.o.(2). The second strategy comprised of utilizing recommended constitutive relations from designrecommendations in SS812310 and RILEM TC 162-TDF. All of the constructed material models werefinally coupled with the FE-models that represented the beams with flexural reinforcement for evaluationof their performance based on their consistency with experiment data.It was found that the material models that were generated from inverse analysis in general would haveyielded successful predictions for the occurrence of shear failure in the reinforced FRC beams, providedthat the governing post-cracking residual tensile parameters were processed with respect to relevantassumptions as to describe uniaxial tensile behavior. However, although it was possible to utilize theproposed calibration method to replicate the load-displacement data for the notched 3PBT specimens withsufficient conformity, it was not possible to arrive at only one unique solution. Instead, multiple outcomescould be obtained based on the initial choice for the input value of the uniaxial tensile strength, leading tothe conclusion that experience and the engineering judgment of the user is of high importance whenadopting this method.Regarding the material models that were derived from constitutive relations in design recommendations,satisfactory estimates for the shear capacity could be obtained from the FE-models that were based onrecommendations by RILEM. The models that were based on SS812310, on the other hand, demonstratedover-stiff behavior and they were unable to provide accurate graphical visualizations of characteristicshear cracking, although the obtained load bearing capacity overall matched the experiment data in caseswhen size effects seemingly had a minor influence. An important observation from the comparison ofthese material models was that the initial drop in tensile strength during crack initiation within an elementis crucial in modeling of FRC, as it accounts for a more realistic behavior through a gradual transitionfrom aggregate bridging mechanisms of PC to the added fiber bridging mechanisms of FRC. Forsituations with high residual tensile strengths in relation to tensile strength at crack initiation, theguidelines in SS812310 become less practical for predicting shear failure by means of NLFEA.

No description available.

This research investigates the flexural behavior of reinforced concrete (RC) beams retrofitted with fiber metal laminate (FML), an advanced hybrid material composed of alternating layers of metal and fiber-reinforced polymer (FRP) composites bonded through a thermoplastic or thermoset polymeric matrix. While FRP composites are commonly used for structural retrofits, their brittle failure mode, due to the linear elastic behavior of the fibers that cannot deform plastically, limits their effectiveness in applications requiring ductility. To address the drawbacks associated with FRP, this project proposes FML as a potential alternative. Flexural testing was conducted on seven RC beams with different configurations of FML and FRP under four-point bending. The goal of the project was finding an ideal retrofit for the RC beam that increased the peak load without a sacrificing the ductility. The beams, which were simply supported, were subjected to two point loads in order to assess their complete load-deformation behavior. Displacements and applied loads were measured at the midspan, and strain data wasrecorded along the length of the retrofits. Four beams were retrofitted with FML, two with FRP, and one served as a control specimen that did not have a retrofit. In order to prevent a premature debonding failure between the RC beam and retrofit, this study also explored different bonding methods: hybrid bonding and unbonded anchorage configurations. Four of the retrofitted beams had a hybrid bonded anchorage configuration and two had an unbonded anchorage configuration. Analytical modeling was performed to predict the behavior of RC beams with various retrofit configurations and bonding types. The modeling procedure for fully bonded retrofits followed the prescribed method in ACI 440.2R-17 that assumes full strain compatibility between the RC beam and retrofit. Due to the lack of strain compatibility for unbonded retorifts, an analytical procedure was developed to generate the moment-curvature response and is reported in Appendix D. The modeling techniques accurately predicted the load-deformation behavior observed in the experiments. The results indicated that FML is an appropriate retrofit material for RC beams, with beam behavior highly dependent on the fiber orientation within the FML. RC Beams retrofitted with fully bonded, unidirectional fibers experienced the highest strength gains but exhibited decreased ductility. In contrast, beams retrofitted with fully bonded, off-axis fibers showed moderate strength gains without a reduction in ductility. Unbonded retrofits were effective in increasing both the strength and ductility of the beams, displaying performance similar to the fully bonded retrofits fiber orientation. This study demonstrates the potential of FML as a retrofit material that offers a balance between strength enhancement and ductility. The main findings highlights the significance of fiber orientation and bonding methods in optimizing the performanae of RC beam retrofits. / Master of Science / This project explored methods to strengthen reinforced concrete (RC) beams using fiber metal laminate (FML), a material created by layering metal sheets with fiber-reinforced polymers (FRP). While FRP is commonly utilized for structural retrofits, it has significant deficiencies: its fibers are brittle and lack ductility compared to metals. FML addresses these issues by combining metals with FRP, resulting in a more ductile and reliable strengthening solution. Seven RC beams were tested by applying two-point loads near the center until failure occurred. Four of these beams were retrofitted with FML, two with FRP, and one remained unaltered as a control specimen. To prevent premature debonding failure between the RC beam and the retrofit, different bonding methods were explored: four retrofitted beams had the retrofit materials fully bonded using hybrid bonded anchorage configurations, while two featured unbonded anchorage configurations. During testing, midspan displacement, applied loads, and strain along the retrofitted areas were measured. Analytical modeling was employed to predict the behavior of RC beams with various retrofit configurations and bonding types. For the fully bonded retrofits, established guidelines from ACI 440.2R-17 were adhered to, assuming full strain compatibility between the RC beam and retrofit. Due to the lack of strain compatibility for unbonded retrofits, a new analytical procedure was developed to generate the moment-curvature response, detailed in Appendix D. These modeling techniques accurately predicted the load-deformation behavior observed in the experiments. The results demonstrated that FML is an effective material for reinforcing RC beams. Performance was largely influenced by the fiber orientation within the FML. Beams reinforced with FML having fibers aligned in one direction exhibited the greatest strength gains but reduced ductility. Conversely, beams with fibers arranged at angles achieved moderate strength increases without compromising ductility. Unbonded retrofits were also effective, enhancing both the strength and ductility of the beams in a manner consistent with fiber orientation trends. In summary, FML offers a promising method for retrofitting RC beams by balancing increased strength with maintained ductility. Fiber orientation and bonding methods are critical factors in optimizing the performance of the strengthened beams.

Thesis (MScEng)--Stellenbosch University, 2012. / ENGLISH ABSTRACT: This study entails the appraisal of the constitutive models available for the non linear finite element analysis of reinforced concrete, using the DIANA finite element package and following generally accepted guidelines for non linear finite element analyses. The constitutive models considered are plasticity and total strain based (fixed and rotating crack) models. The appraisal consists of the analysis of various experiments performed on reinforced concrete beams that are governed by compressive, shear and tensile dominated failures. The investigation is not limited to the accuracy of the results obtained using these models but also of the consistency of the results obtained with regard to various mesh types and sizes, as well as a study of the individual influence of several material parameters. The intention of the study was to provide the reader with an indication of the performance capacity (accuracy and consistency) of the available constitutive models, where the notion of the use of the results obtained from non linear finite element analyses for design purposes is considered. The results obtained were varied. The models performed reasonably well in the compressive and tension dominated studies, with the importance of accurate material parameters being emphasized especially for the more advanced cementitious materials investigated. The total strain rotating crack model also showed a proclivity of simulating incorrect failure modes as well as exhibiting reluctance towards stress redistribution. All models used for the shear dominated study yielded mostly inaccurate and inconsistent results, but it was found that the four node quadrilateral element with selective reduced integration performed the best. The plasticity model did not capture shear failure well, and convergence was often not attained. The constant shear retention factor of the total strain fixed crack model was found to yield more detailed response curves for the smaller mesh sizes. The results of the tension dominated beams inspired more confidence in the models as quite accurate values were attained, especially by the plasticity model used. The ability of the available models to simulate realistic structural behaviour under various failure modes is very limited, as is evident from the results obtained. The development of a more advanced and robust model is required, which can provide consistently accurate results and failure modes, and even ‘anticipate’ potential failure modes not considered by the user.

A structure subjected to extreme load due to explosion or human error may lead to progressive collapse. One of the direct methods specified by design guidelines for assessing progressive collapse is the Alternate Load Path method which involves removal of a structural member and analysing the structure to assess its potential of bridging over the removed member without collapse. The use of this method in assessing progressive collapse therefore requires that the vertical load resistance function of the bridging beam assembly, which for a typical laterally restrained reinforced concrete (RC) beams include flexural, compressive arching action and catenary action, be accurately predicted. In this thesis, a comprehensive study on a reliable prediction of the resistance function for the bridging RC beam assemblies is conducted, with a particular focus on a) the arching effect, and b) the catenary effect considering strength degradations. A critical analysis of the effect of axial restraint, flexural reinforcement ratio and span-depth ratio on compressive arching action are evaluated in quantitative terms. A more detailed theoretical model for the prediction of load-displacement behaviour of RC beam assemblies within the compressive arching response regime is presented. The proposed model takes into account the compounding effect of bending and arching from both the deformation and force points of view. Comparisons with experimental results show good agreement. Following the compressive arching action, catenary action can develop at a much larger displacement regime, and this action could help address collapse. A complete resistance function should adequately account for the catenary action as well as the arching effect. To this end, a generic catenary model which takes into consideration the strength degradation due to local failure events (e.g. rupture of bottom rebar or fracture of a steel weld) and the eventual failure limit is proposed. The application of the model in predicting the resistance function in beam assemblies with strength degradations is discussed. The validity of the proposed model is checked against predictions from finite element model and experimental tests. The result indicate that strength degradation can be accurately captured by the model. Finally, the above developed model framework is employed in investigative studies to demonstrate the application of the resistance functions in a dynamic analysis procedure, as well as the significance of the compressive arching effect and the catenary action in the progressive collapse resistance in different designs. The importance of an accurate prediction of the arching effect and the limiting displacement for the catenary action is highlighted.

Made available in DSpace on 2014-06-11T19:25:22Z (GMT). No. of bitstreams: 0 Previous issue date: 2003-01-31Bitstream added on 2014-06-13T19:47:23Z : No. of bitstreams: 1 gamino_al_me_ilha.pdf: 1439799 bytes, checksum: f5276e70048212940034e70e154a258f (MD5) / Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) / Apresenta-se como objeto desta pesquisa o estudo numérico não-linear da ductilidade de vigas de concreto armado convencional e de alto desempenho. Toda a análise numérica é efetuada no código de cálculo baseado no método dos elementos finitos CASTEM 2000, que utiliza o modelo reológico elastoplástico perfeito para o aço, o modelo de Drucker-Prager para o concreto e o método de Newton-Raphson para a solução de sistemas não-lineares. O núcleo deste trabalho concentra-se na obtenção de curvas força - deslocamento e momento - curvatura com a finalidade de quantificar respectivamente os índices de ductilidade global e local das vigas analisadas. De início, confrontam-se as respostas numéricas obtidas com resultados experimentais fornecidos pela literatura a fim de garantir confiabilidade à análise numérica realizada. Posteriormente, efetua-se a determinação da capacidade de deformação inelástica do elemento estrutural em questão, variando-se a resistência à compressão do concreto, a taxa geométrica de armadura longitudinal de tração, a tensão de escoamento das armaduras, o espaçamento entre estribos, a base da seção transversal do elemento estrutural e o efeito escala. Estes parâmetros foram avaliados para dois casos de solicitação: flexão simples tipo I e flexão simples tipo II. O primeiro caso caracteriza-se pela ação de forças simétricas aplicadas à 1/3 e 2/3 do vão e a segunda por uma força centrada no meio do vão. A linha de tendência geral observada foi de uma maior ductilização das vigas sujeitas à flexão simples tipo II, em detrimento às solicitadas por flexão simples tipo I. Quanto ao efeito escala observa-se que a ductilização das vigas é inversamente proporcional à esbeltez das mesmas. / The objective of this thesis is the study of the ductility of high and conventional strength reinforced concrete beams by non-linear numerical simulations. The numerical analysis is based on the finite element method implemented in CASTEM 2000. This program uses the constitutive elastoplastic perfect model for the steel, the Drucker-Prager model for the concrete and the Newton-Raphson for the solution of non-linear systems. This work concentrates on the determination of force - displacement and moment - curvature curves with the purpose of quantifying the global and local ductility indexes of the beams. First, the numeric responses are confronted with experimental results found in the literature in order to check the reliability of the numerical analyses. Later, a parametric study is carried on. The inelastic deformation capacity of the structural element is investigated by varying the concrete compressive strength, the longitudinal reinforcement ratio, the yield stress of the reinforcement, the spacing between stirrups, the member section dimensions and the element size. These parameters have been analyzed for two cases: simple type I and simple type II bending. The first case is characterized by the action of applied symmetrical forces to the 1/3 and 2/3 of the beam size and second for a force centered in the middle of the beam size. The general tendency observed points to a high ductilization of the beams subjected to simple type II bending in comparison to the ones subjected to simple type I bending. With respect to the element size, it is noticed that the ductility of the beams is inversely proportional to their slendernesses.

Gelžbetonis yra kompozitinė medžiaga, kurios komponentai yra betonas ir plieninė armatūra. Kaip žinoma, betono stipris tempiant yra 1020 kartų mažesnis nei stipris gniuždant. Atrodytų, kad tempiamojo betono įtaka, atlaikant įrąžas skerspjūvyje, yra nereikšminga. Iš tiesų, nustatant lenkiamųjų elementų stiprumą normaliniame pjūvyje, tempiamo betono įtempių galima nevertinti. Kita vertus, skaičiuojant įlinkius, neįvertinus tempiamojo betono įtakos, gali būti daroma didesnė nei 100 % paklaida. Adekvatus supleišėjusio tempiamojo betono įtakos įvertinimas, nustatant trumpalaike apkrova veikiamų gelžbetoninių elementų deformacijas, yra bene svarbiausia ir sudėtingiausia problema. Plyšio vietoje betonas negali atlaikyti tempimo įtempių, todėl visą įrąžą atlaiko armatūra. Kadangi plyšyje ir gretimuose pjūviuose armatūra praslysta betono atžvilgiu, kontakto zonoje atsiranda tangentiniai įtempiai. Šie įtempiai perduodami betonui, todėl jis atlaiko tempimo įtempius. Armatūros ir betono sąveika ruožuose tarp plyšių standina gelžbetoninį elementą. Supleišėjusio betono gebėjimas atlaikyti tempimo įtempius vadinama tempimo sustandėjimu (angl. tension stiffening). Šis efektas dažniausiai modeliuojamas supleišėjusio betono įtempių ir deformacijų diagrama, taikant vidutinių plyšių koncepciją. Tuomet neatsižvelgiama į diskrečius plyšius, o supleišėjęs betonas traktuojamas kaip ortotropinė medžiaga su pakitusiomis savybėmis. Dauguma tempimo sustandėjimo modelių įvertina betono įtempių... [toliau žr. visą tekstą] / Modelling behaviour of cracked tensile concrete is a complicated issue. Due to bond with reinforcement, the cracked concrete between cracks carries a certain amount of tensile force normal to the cracked plane. Concrete adheres to rein-forcement bars and contributes to overall stiffness of the structure. The phe-nomenon, called tension-stiffening, has significant influence on the results of short-term deformational analysis. Assumption of a tension-stiffening law has great influence on numerical results of load – deflection behaviour of reinforced concrete members subjected to short – term loading. Under wrong assumption of this law, errors in calculated deflections, particularly for lightly members, may exceed 100 %. Most known tension-stiffening relationships relate average stresses to average strains. However, some experimental and theoretical investi-gations have shown that tension-stiffening may be affected by other parameters. The scientific supervisor of the thesis has proposed a tension-stiffening model depending on reinforcement ratio. This model has been developed using experi-mental data reported in the literature. Besides, concrete shrinkage effect was not taken into account. The main objective of this PhD dissertation is to propose a tension-stiffening law for bending RC members subjected to short-term loading with eliminated concrete shrinkage effect.

Modelling behaviour of cracked tensile concrete is a complicated issue. Due to bond with reinforcement, the cracked concrete between cracks carries a certain amount of tensile force normal to the cracked plane. Concrete adheres to rein-forcement bars and contributes to overall stiffness of the structure. The phe-nomenon, called tension-stiffening, has significant influence on the results of short-term deformational analysis. Assumption of a tension-stiffening law has great influence on numerical results of load – deflection behaviour of reinforced concrete members subjected to short – term loading. Under wrong assumption of this law, errors in calculated deflections, particularly for lightly members, may exceed 100 %. Most known tension-stiffening relationships relate average stresses to average strains. However, some experimental and theoretical investi-gations have shown that tension-stiffening may be affected by other parameters. The scientific supervisor of the thesis has proposed a tension-stiffening model depending on reinforcement ratio. This model has been developed using experi-mental data reported in the literature. Besides, concrete shrinkage effect was not taken into account. The main objective of this PhD dissertation is to propose a tension-stiffening law for bending RC members subjected to short-term loading with eliminated concrete shrinkage effect. / Gelžbetonis yra kompozitinė medžiaga, kurios komponentai yra betonas ir plieninė armatūra. Kaip žinoma, betono stipris tempiant yra 10-20 kartų mažesnis nei stipris gniuždant. Atrodytų, kad tempiamojo betono įtaka, atlaikant įrąžas skerspjūvyje, yra nereikšminga. Iš tiesų, nustatant lenkiamųjų elementų stiprumą normaliniame pjūvyje, tempiamo betono įtempių galima nevertinti. Kita vertus, skaičiuojant įlinkius, neįvertinus tempiamojo betono įtakos, gali būti daroma didesnė nei 100 % paklaida. Adekvatus supleišėjusio tempiamojo betono įtakos įvertinimas, nustatant trumpalaike apkrova veikiamų gelžbetoninių elementų deformacijas, yra bene svarbiausia ir sudėtingiausia problema. Plyšio vietoje betonas negali atlaikyti tempimo įtempių, todėl visą įrąžą atlaiko armatūra. Kadangi plyšyje ir gretimuose pjūviuose armatūra praslysta betono atžvilgiu, kontakto zonoje atsiranda tangentiniai įtempiai. Šie įtempiai perduodami betonui, todėl jis atlaiko tempimo įtempius. Armatūros ir betono sąveika ruožuose tarp plyšių standina gelžbetoninį elementą. Supleišėjusio betono gebėjimas atlaikyti tempimo įtempius vadinama tempimo sustandėjimu (angl. tension stiffening). Šis efektas dažniausiai modeliuojamas supleišėjusio betono įtempių ir deformacijų diagrama, taikant vidutinių plyšių koncepciją. Tuomet neatsižvelgiama į diskrečius plyšius, o supleišėjęs betonas traktuojamas kaip ortotropinė medžiaga su pakitusiomis savybėmis. Dauguma tempimo sustandėjimo modelių įvertina betono įtempių... [toliau žr. visą tekstą]