With the use of the simplistic equivalent circuits, loss mechanism in conventional power MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) gate drive circuits is analyzed. Resonant gate drive techniques are investigated and a new resonant gate drive circuit is presented. The presented circuit adds minor complexity to conventional gate drivers but reduces the MOSFET gate drive loss very effectively. To further expand its use in driving Half-Bridge MOSFETs, another circuit is proposed in this thesis. The later circuit simplifies the isolation circuitry for the top MOSFET and meanwhile consumes much lower power than conventional gate drivers. / Master of Science

The demand for high power density, high efficiency bus converters has increased interest in resonant topologies, particularly the LLC resonant converter. LLC resonant converters offer several advantages in efficiency, power density, and hold up time extension capability. Among high voltage (>500V) MOSFETs, Super Junction MOSFETs, such as Infineon's CoolMOS parts, offer lower Rds on than conventional parts and are a natural choice for this application to improve efficiency. However, there is a history of converter failure due to reverse recovery problems with the primary switch's body diode. Before selecting CoolMOS devices for use in a LLC resonant converter, it is necessary to investigate its performance in this application. Field failures of PWM soft switching phase shift full bridge converters have been attributed to large reverse recovery charge in the primary side MOSFET body diode. Under low load conditions the device cannot fully recover, and the large reverse recovery current can cause the device to enter secondary break down, leading to failure. The unique structure of Super Junction MOSFETs, such as CoolMOS, avoid this failure mode by providing a different path for the reverse current; however, the reverse recovery charge of CoolMOS devices is large and can cause a loss of efficiency. For this reason, it is important to avoid conditions under which the reverse recovery characteristics of the body diode can be seen. / Master of Science

Recently induction cookers, which are based on induction heating principle, have become quite popular due to their advantages such as high energy efficiency, safety, cleanliness, and compact size. However, it is widely known that with current technology, induction cookers require the cookware to be made of magnetic materials such as iron and stainless steel. This is why a lot of cookware is labeled "Induction Ready" on the bottom. The limited choice of "Induction Ready" cookware causes inconvenience to customers and limits the growing popularity of the induction cooker. Therefore, a novel induction cooker, which can work for non-magnetic material cookware such as aluminum and copper, can be very competitive in the market. This thesis studies the induction cooking application; briefly introduces its fundamental principle, research background and the motivation of the development of a non-magnetic material induction cooker. Followed by the research motivation, three commonly used inverter topologies, series resonant inverter, parallel resonant inverter, and single-ended resonant inverter, are introduced. A comparative study is made among these three topologies, and the comparative study leads to a conclusion that the series resonant inverter is more suitable for non-magnetic material induction cooking application. The thesis also presents several major issues about non-magnetic material induction cooking and how to deal with these issues through induction coil design, higher operating frequency and novel control strategy. Because of non-magnetic material's low resistivity and permeability characteristics, it is difficult to be heated and to achieve soft-switching while the coupling between the induction coil and the cooking pan can be easily changed. Later in this thesis, these issues will be discussed in detail and some potential solutions to these issues such as self-sustained oscillating control, optimized induction coil design, proper selection of power semiconductor device, etc. A 1.5 kW high frequency series resonant inverter with self-sustained oscillating control is prototyped. Experimental results demonstrated successful operation of the resonant inverter under up to 1.5 kW, and the inverter's capability to maintain zero-voltage turn-on during wide operating condition is confirmed. At the end, a summary is given about the research work done in the thesis and future research work is discussed. / Master of Science

Bandwidth enhancement of low-profile omnidirectional, electrically-small antennas has evolved from the design and construction of AM transmitter towers eighty years ago to current market demand for battery-powered personal communication devices. Electrically-small antenna theory developed with well-known approximations for characterizing radiation properties of antenna structures that are fractions of the radiansphere. Current state-of-the-art wideband small antennas near kaH1 have achieved multiple-octave impedance bandwidths when utilizing volume-efficient designs. Significant advances in both the power and miniaturization of microelectronics have created a second possible approach to enhance bandwidth. Frequency agility, via switch tuning of reconfigurable structures, offers the possibility of the direct integration of high-speed electronics to the antenna structure. The potential result would provide a means to translate a narrow instantaneous bandwidth across a wider operating bandwidth. One objective of the research was to create a direct comparison of the passive- multi-resonant and active-reconfigurable approaches to enhance bandwidth. Typically, volume-efficient, wideband antennas are unattractive candidates for low-profile applications and conversely, active electronics integrated directly antenna elements continue to introduce problematic loss mechanisms at the proof-of-concept level The dissertation presents an analysis method for wide bandwidth self-resonant antennas that exist in the 0.5dkad1.0 range. The combined approach utilizes the quality factor extracted directly from impedance response data in addition to near-and-far field modal analyses. Examples from several classes of antennas investigated are presented with practical boundary conditions. The resultant radiation properties of these antenna-finite ground plane systems are characterized by an appreciable percentage of radiated power outside the lowest-order mode. Volume-efficient structures and non-omnidirectional radiation characteristics are generally not viable for portable devices. Several examples of passive structures, representing different antenna classes are investigated. A PIN diode, switch-tuned low-profile antenna prototype was also developed for the comparison which demonstrated excessive loss in the physical prototype. Lastly, a passive, low-profile multi-resonant antenna element with monopole radiation is introduced. The structure is an extension of the planar inverted-F antenna with the addition of a capacitance-coupled parasitic to enhance reliable operation in unknown environments. / Ph. D.

An optical detection technique is developed to detect and measure the resonant vibration of the cellular membrane. Biological membranes are active components of living cells and play a complex and dynamic role in life processes. They are believed to have oscillation modes of frequencies in the range of 1 to 1000 GHz. To measure such a high-frequency vibration, a linear laser cavity is designed to produce a train of femtosecond pulses of adjustable repetition rate. The method is then directly applied to liposomes, "artificial membrane", stained with a liphophilic potential sensitive dye. The spectral behavior of a selection of potential sensitive dyes in the membrane is also studied.

Scientists and engineers measure dielectric constant because it gives them better understanding of materials and helps them to know how to integrate these materials into their design processes;it also helps them to shorten design life cycle,and aside these two functions,it has numerous uses all of which cannot be enumerated in this section.Owing to its usefulness,various measurement methods of dielectric constant of materials have been developed over the years.Each method has its limitations which affect the accuracy of the measurement;these limitations range from frequency,temperature,and  mearsurement environment to material under test.   In this thesis,four most common methods of measuring dielectric constant were discussed and the most accurate one,the resonant method,was chosen and worked on .The project was executed by making a mathematical analysis of the ring resonator which was later simulated in HFSS to get results which would be comparable to ones obtained in  laboratory measurements.   The ring was fabricated and taken to the laboratory for measurement.Two monopole antennas were connected to the two ports of a VNA with one antenna serving as the transmitter and the other serving as the receiver.   The resonant frequencies obtained were combined with the geometric parameters of the ring resonator and that of the MUT in equations written into MATLAB scripts;this equations were used to extract the dielectric constant of the MUT.

Resonante Mikrobauelemente mit elektrostatischem Antrieb finden seit einigen Jahren vermehrt Anwendung in vielen Bereichen der Technik. So beruhen beispielsweise Drehraten- oder Beschleunigungssensoren, die im Automobilbau eingesetzt werden auf diesem Prinzip. Neue Anwendungsfelder ergeben sich vor allem für Aktoren, beispielsweise für die am Fraunhofer IPMS entwickelten Mikroscannerspiegel mit Out-of-plane-comb-Antrieb. Sie dienen zur geometrischen Ablenkung von Licht und können zur Realisierung von hochintegrierten Systemen zur Ausgabe (Laser-Projektor) oder Aufnahme (Laser-Imager) von Daten genutzt werden. Zum Entwurf von Mikroaktoren gibt es eine Reihe von Arbeiten, die sich meist auf ein konkretes Antriebsprinzip beziehen oder den Entwurf im Allgemeinen behandeln. Die vorliegende Arbeit verfolgt daher das Ziel, speziell die Randbedingungen beim Entwurf resonanter Mikroaktoren mit Out-of-plane-comb-Antrieb zu identifizieren bzw. zu systematisieren sowie die gewonnenen Erkenntnisse in einem effizienten Entwurfsprozess umzusetzen. Dabei sollen möglichst auch relevante nichtlineare Effekte berücksichtigt werden, sodass sich neue Möglichkeiten zur Optimierung der Bauelemente und damit zur Erweiterung des Entwurfsraums ergeben. / Electrostatically driven microsystems are utilized in technical systems for several years. For instance, they are used in automotive applications as acceleration sensors or angular rate sensors. New fields of applications appear especially for actuators. The scanning micromirror of the Fraunhofer Institute for Photonic Microsystems is such an actuator. It is a micro-­optical-­electrical microsystem (MOEMS) which is driven resonantly by an electrostatic comb drive and can be used in scanning laser imaging systems or laser projectors. Several technical and scientific publications occupy with the design and the simulation of microactuators, which refer usually to a concrete drive principle or to the issues of design in general. The intention of this thesis is to identify and systematize particularly the boundary conditions of design regarding to resonant micro actuators with out-­of-­plane­comb drive. The findings are implemented in efficient design tools and design processes. One emphasis thereby is the investigation of nonlinear properties and effects. This includes geometrically non-­linearities of suspensions as well as non-linearities caused by fluid damping and the electrostatic comb drive. The findings are utilized in an analytical, nonlinear stability analysis of the device's equation of motion as well as in an object oriented software library for the MATLAB environment, which can be used to create nonlinear reduced order models of scanning micromirrors. With the developed techniques for design and optimization the available parameter range of scanning micromirrors can be extended. By that means, it is possible to improve the properties of existing devices as well as create new devices with outreaching performance.

This thesis deals with the design of wireless power transfer at a distance of 600 mm dimensioned to 20 kW. The transfer is provided by inductive coupling of resonant circuits with 800 mm diameter coils. It contains a description of the design and calculations of individual parts, stating specific values. It also includes description and schematics of control circuits.

Isolated inverters feature the freedom in voltage step-up/down, electrical safety, and modularity. Among them, pseudo-dc-link inverters have the advantage of high efficiency due to their single-stage structure. Traditionally, pseudo-dc-link inverters are based on pulse-width-modulated converters, which suffer from hard switching, the need for auxiliary components, and/or high current stresses. Meanwhile, the series resonant converter has been prevalent in past decades due to its simplicity and high efficiency. Therefore, it is intriguing to design a single-stage inverter based on a series resonant converter. However, there are limited papers regarding such an inverter topology. To figure out the reason, basic modulation methods proposed or implied in the literature are summarized and evaluated through circuit simulation software. It turns out each basic modulation method has at least one critical drawback in modulation range, hard switching, and/or high current stresses. Given the deficiencies in the basic modulation methods, a hybrid modulation method is proposed here. The proposed method combines variable-frequency modulation in the high-output region and short pulse-density modulation in the low-output region. In this way, all the aforementioned critical drawbacks can be greatly alleviated. The hybrid modulation method is compared to the basic modulation methods based on three design metrics: the rms value of the resonant current, the magnetic flux of the transformer, and the turn-off current. By these design metrics that directly related to power losses, the benefit of the proposed method in terms of efficiency can be explained. Moreover, a power loss model is also established to provide more insights into the inverter's efficiency performance. It helps demonstrate how the selection of resonant tank and other factors affects the power loss distribution. Also, an inverter design procedure is introduced and a prototype is built to verify the proposed modulation method. The results show that the switching losses, especially the turn-on loss, can be well suppressed, and the losses in other passive components are well restrained. This implies the proposed method is suitable for high-frequency applications. Other than efficiency, output waveform quality is also important for an inverter. However, the changing plant model makes the controller design difficult. Therefore, a third-order model established by other researchers has been adopted to identify the pole locations. In addition, a gain-varying method is proposed for the compensator to reduce the gain variance caused by different operating conditions. The experimental results show that without the gain-varying method, the inverter may have issues in slow tracking and/or instability. Finally, in some scenarios, the inverter based on a series resonant converter can be regarded as a module. A multi-modular inverter can be formed by connecting the modules in an input-parallel-output-series configuration. In this case, a technique termed sequential waveform synthesis can be applied. The proposed technique can extend the region of variable-frequency modulation and shorten the region of short pulse-density modulation. This is beneficial to efficiency based on an analysis. With more than a certain amount of modules connected, the short pulse-density modulation can even be waived, which means the multi-modular inverter can be free from turn-on loss. In summary, this dissertation focuses on developing modulation methods for inverters based on the series resonant converter. Soft-switching feature and high efficiency are the two top priorities. The analytic and experimental results are provided based on standalone applications. / Doctor of Philosophy / Inverters are an important part of a modern electric power system, as they convert dc electric power into ac electric power. In some applications, inverters with electrical insulation (isolated inverters) are preferred due to the need for engineering freedom, safety, and other reasons. However, each conventional isolated inverter has some of the following drawbacks: hard-switching in semiconductor devices, high circulating current, poor transformer utilization, and high complexity. These drawbacks limit the efficiency and compactness of an inverter system, making the system less attractive to practical applications. An inverter based on a series resonant converter seems to be a solution because the series resonant converter is known for being simple and highly-efficient. However, there has yet to be a proper modulation method for it. Therefore, the main contribution of this dissertation is to propose a hybrid modulation method. With the proposed method, the inverter can operate with high efficiency. Furthermore, the hard-switching can be well suppressed, which means a high-frequency, compact design is possible. Besides the theory of the proposed method, this dissertation also includes a power loss model, a hardware design procedure, and analytic comparisons with other methods. In addition, a digital approach to control the inverter is proposed. Without it, the output voltage waveform may be highly distorted. Finally, another sequential control strategy is proposed in this dissertation for an integrated system. The integrated system is composed of multiple inverters based on a series resonant converter. With the sequential control strategy, the overall output waveform quality of the integrated system can be improved.

In comparison with PWM converters, resonant converters are gaining increasing popularity for cases in which efficiency and power density are at a premium. However, the lack of an accurate small-signal model has become an impediment to performance optimization. Many modeling attempts have been made to date. Besides the discrete time-domain modeling, most continuous-time modeling approaches are based on fundamental approximation, and are thus unable to provide sufficient accuracy for practical use. An equivalent circuit model was proposed by Yang, which works well for series resonant converters (SRCs) with high Q (quality factor), but which is inadequate for LLC resonant converters. Furthermore, the model is rather complicated, with system orders that are as high as five and seven for the SRC and LLC converter, respectively. The crux of the modeling difficulty is due to the underlying assumption based on the use of a band-pass filter for the resonant tank in conjunction with a low-pass output filter, which is not the case for most practical applications. The matter is further complicated by the presence of a rectifier, which is a nonlinearity that mixes and matches the original modulation frequency. Thus, the modulation signal becomes intractable when using a frequency-domain modeling approach. This dissertation proposes an extended describing function modeling that is based on a Fourier analysis on the continuous-time-domain waveforms. Therefore, all important contributions from harmonics are taken into account. This modeling approach is demonstrated on the frequency-controlled SRC and LLC converters. The modeling is further extended to, with great accuracy, a charge-controlled LLC converter. In the case of frequency control, a simple third-order equivalent circuit model is provided with high accuracy up to half of the switching frequency. The simplified low-frequency model consists of a double pole and a pair of right-half-plane (RHP) zeros. The double pole, when operated at a high switching frequency, manifests the property of a well-known beat frequency between the switching frequency and the resonant frequency. As the switching frequency approaches the resonant frequency of the tank, a new pair of poles is formed, representing the interaction of the resonant tank and the output filter. The pair of RHP zeros, which contributes to additional phase delay, was not recognized in earlier modeling attempts. In the case of charge control, a simple second-order equivalent circuit model is provided. With capacitor voltage feedback, the order of the system is reduced. Consequently, the resonant tank behaves as an equivalent current source and the tank property is characterized by a single pole. The other low-frequency pole represents the output capacitor and the load. However, the capacitor voltage feedback cannot eliminate the high-frequency poles and the RHP zeros. These RHP zeros may be an impediment for high-bandwidth design if not properly treated. Based on the proposed model, these unwanted RHP zeros can be mitigated by either changing the resonant tank design or by proper feedback compensation. The accurate model is essential for a high-performance high-bandwidth LLC converter. / Doctor of Philosophy / For high-frequency power conversion, resonant converters are increasingly popular. However, the lack of an accurate small-signal model has become an impediment to performance optimization. The existing equivalent circuit model and its simplified circuit were based on fundamental approximation, where the resonant tank was deemed a good band-pass filter. These models work well for series resonant converters (SRCs) with high Q (quality factor), but are inadequate for LLC resonant converters. The crux of the modeling difficulty is due to the fact that the operation of this type of resonant converter is based on the use of a band-pass filter in conjunction with a low-pass filter. The matter is further complicated by the presence of a rectifier, which is a nonlinearity that mixes and matches the original modulation frequency. Thus, the modulation signal becomes intractable when using a frequency-domain modeling approach. This dissertation proposes an extended describing function modeling that is based on a Fourier analysis on the continuous-time-domain waveforms. Therefore, all important contributions from harmonics are taken into account. This modeling approach is demonstrated on the frequency-controlled SRC, frequency-controlled LLC converter, and charge-controlled LLC converter, and the resulting models are proven to be accurate at all frequencies. A simple equivalent circuit model is provided that targets the frequency range below the switching frequency. This simple, accurate model is able to predict the small-signal behaviors of the LLC converter with high accuracy at half of the switching frequency. At high modulation frequencies, the resonant converter behaves like a non-minimum phase system, which was neither recognized nor characterized before. This property can be represented by RHP zeros, and these RHP zeros may be an impediment for high-bandwidth design if not properly treated. Based on the proposed model, these unwanted RHP zeros can be mitigated by either changing the resonant tank design or by proper feedback compensation. Accurate modeling is essential for a high-performance high-bandwidth LLC converter.