Recent years have witnessed a growing demand for broadband wireless communication services such as on-the-go web-browsing, high speed data transfer and streaming of high definition multimedia. In response to this growth, there has been a rapid progress in research and development of technologies supporting high-speed wireless networks offering flexibility and scalability to heterogeneous consumer requirements. A fundamental challenge to the reliable operation of a wireless communication link is the wireless channel which is influenced by time-variant noise, interference, multipath and scarcity of the available frequency spectrum. Due to the wireless nature of the signal transmission and the manner in which energy is distributed or collected, an antenna has a profound influence on an efficient operation of wireless link. Because nowadays an antenna is required to work with many wireless standards, it poses one of the most difficult design and development technological problems. In the past, many antenna designs were concentrated on conventional outdoor applications such as satellite communications, terrestrial point to point communications and cellular base stations. In these applications, the primary design goal was the antenna electrical performance. In case of indoor applications, the designer has to pay attention not only to the electrical performance but also to mechanical, environmental and aesthetic features of antenna. In this thesis, the investigations into design and development of antenna for indoor wireless communication systems that are either currently widespread or quickly entering the consumer market are carried out. First, a single band circularly polarized Radial Line Slot Array antenna covering 2.4GHz ISM frequency spectrum of IEEE 802.11b/g protocol is proposed. Then, an access point antenna for IEEE 802.11a/b/g WLAN applications operating in a dual frequency band covering 2.4GHz and 5.2GHz frequency spectra is described. It consists of a RLSA antenna and a patch antenna combined in one body. During the design stage, in addition to characteristics such as return loss, radiation pattern and polarization, attention is paid to mechanical rigidity, light weight and low visual impact of these radiating structures. A low manufacturing cost is also part of the design strategy. This is important because of competitive commercial market of WLAN applications which is sensitive to the development cost. In theoretical investigations, a Field Matching Method is utilized to achieve a first order approximation to the coaxial-to-waveguide transition forming the feeding element of the RLSA antenna. Next, the full EM analysis (HFSS™) based on Field Element Method is applied to simulate the single and dual band antennas. Both types of access point antennas are manufactured and tested. Experimental results are compared with simulation results. The next part of this thesis presents the investigations into antenna diversity techniques for a wireless communication link in an indoor environment. The design of the automated experimental testbed is presented. This testing facility is used to measure the signal strength levels of a communication link between a mobile wireless device and an access point when they are equipped with multiple element antennas (MEAs). Special attention is given to the benefits of using MEA in a rich scattering environment that is accompanied the experiment. Full design details including electrical and mechanical features are provided. For a given feeding configuration, the testbed allows for measuring the received signal strength when the receiving module is moved over a circular area in an indoor environment. First set of experiments concerns the MEA system that utilizes two single-port transceivers each equipped with either 180º or 90º 3dB hybrid. By using alternatively one of the two input ports of the hybrids to feed a pair of monopole antennas several different transmission or reception modes of the 2x2 MEA communication link are investigated. The next set of experiments focuses on the performances of an indoor wireless system which uses either linearly or circularly polarized antennas at the two sides of the communication link. The overall diversity results indicate that by marginally increasing an overall system complexity (by using simple hybrid circuits and antennas), traditional transceiver systems equipped with MEA can provide significant improvements in the quality of indoor wireless link. The final part of this thesis presents the investigations into the design of planar monopole antennas that offer good return loss and omni-directional radiation pattern characteristics over an Ultra Wide frequency Band (UWB) spanning from 3.1GHz to 10.6GHz. Two types of planar monopole antennas are investigated. First, the ring type square with semi-circular base monopole antenna placed vertically above a finite ground plane is introduced followed by its design, manufacturing and testing. The second UWB antenna which is proposed in this thesis is a printed square with semi-circular base monopole antenna. This antenna is positioned in the same plane as ground and thus offers direct integration with a front-end circuitry of wireless transceiver. Several variations of this type of antenna featuring different outlines are designed, manufactured and tested. The obtained experimental results show a good agreement with the simulation results, as accomplished with the full EM analysis and simulation software HFSS™.

Recent years have witnessed a growing demand for broadband wireless communication services such as on-the-go web-browsing, high speed data transfer and streaming of high definition multimedia. In response to this growth, there has been a rapid progress in research and development of technologies supporting high-speed wireless networks offering flexibility and scalability to heterogeneous consumer requirements. A fundamental challenge to the reliable operation of a wireless communication link is the wireless channel which is influenced by time-variant noise, interference, multipath and scarcity of the available frequency spectrum. Due to the wireless nature of the signal transmission and the manner in which energy is distributed or collected, an antenna has a profound influence on an efficient operation of wireless link. Because nowadays an antenna is required to work with many wireless standards, it poses one of the most difficult design and development technological problems. In the past, many antenna designs were concentrated on conventional outdoor applications such as satellite communications, terrestrial point to point communications and cellular base stations. In these applications, the primary design goal was the antenna electrical performance. In case of indoor applications, the designer has to pay attention not only to the electrical performance but also to mechanical, environmental and aesthetic features of antenna. In this thesis, the investigations into design and development of antenna for indoor wireless communication systems that are either currently widespread or quickly entering the consumer market are carried out. First, a single band circularly polarized Radial Line Slot Array antenna covering 2.4GHz ISM frequency spectrum of IEEE 802.11b/g protocol is proposed. Then, an access point antenna for IEEE 802.11a/b/g WLAN applications operating in a dual frequency band covering 2.4GHz and 5.2GHz frequency spectra is described. It consists of a RLSA antenna and a patch antenna combined in one body. During the design stage, in addition to characteristics such as return loss, radiation pattern and polarization, attention is paid to mechanical rigidity, light weight and low visual impact of these radiating structures. A low manufacturing cost is also part of the design strategy. This is important because of competitive commercial market of WLAN applications which is sensitive to the development cost. In theoretical investigations, a Field Matching Method is utilized to achieve a first order approximation to the coaxial-to-waveguide transition forming the feeding element of the RLSA antenna. Next, the full EM analysis (HFSS™) based on Field Element Method is applied to simulate the single and dual band antennas. Both types of access point antennas are manufactured and tested. Experimental results are compared with simulation results. The next part of this thesis presents the investigations into antenna diversity techniques for a wireless communication link in an indoor environment. The design of the automated experimental testbed is presented. This testing facility is used to measure the signal strength levels of a communication link between a mobile wireless device and an access point when they are equipped with multiple element antennas (MEAs). Special attention is given to the benefits of using MEA in a rich scattering environment that is accompanied the experiment. Full design details including electrical and mechanical features are provided. For a given feeding configuration, the testbed allows for measuring the received signal strength when the receiving module is moved over a circular area in an indoor environment. First set of experiments concerns the MEA system that utilizes two single-port transceivers each equipped with either 180º or 90º 3dB hybrid. By using alternatively one of the two input ports of the hybrids to feed a pair of monopole antennas several different transmission or reception modes of the 2x2 MEA communication link are investigated. The next set of experiments focuses on the performances of an indoor wireless system which uses either linearly or circularly polarized antennas at the two sides of the communication link. The overall diversity results indicate that by marginally increasing an overall system complexity (by using simple hybrid circuits and antennas), traditional transceiver systems equipped with MEA can provide significant improvements in the quality of indoor wireless link. The final part of this thesis presents the investigations into the design of planar monopole antennas that offer good return loss and omni-directional radiation pattern characteristics over an Ultra Wide frequency Band (UWB) spanning from 3.1GHz to 10.6GHz. Two types of planar monopole antennas are investigated. First, the ring type square with semi-circular base monopole antenna placed vertically above a finite ground plane is introduced followed by its design, manufacturing and testing. The second UWB antenna which is proposed in this thesis is a printed square with semi-circular base monopole antenna. This antenna is positioned in the same plane as ground and thus offers direct integration with a front-end circuitry of wireless transceiver. Several variations of this type of antenna featuring different outlines are designed, manufactured and tested. The obtained experimental results show a good agreement with the simulation results, as accomplished with the full EM analysis and simulation software HFSS™.

L'objectif général est de développer un nouvel outil numérique dédié à la focalisation en 3D de l'énergie en zone de champ très proche par un système antennaire. Cet outil permettra de définir la distribution spatiale complexe des champs dans l'ouverture rayonnante afin de focaliser l'énergie sur un volume quelconque en zone de champ réactif. L'hybridation de cet outil avec un code de calcul dédié à l'analyse rapide d‘antennes SIW par la méthode des moments permettra de synthétiser une antenne SIW ad-hoc. Les structures antennaires sélectionnées seront planaires comme par exemple les antennes RLSA (Radial Line Slot Array). Les dimensions de l'antenne (positions, dimensions et nombre de fentes) seront définies à l'aide des outils décrits ci-dessus. Les résultats numériques ainsi obtenus seront validés d'abord numériquement par analyse électromagnétique globale à l'aide de simulateurs commerciaux, puis expérimentalement en ondes millimétriques (mesure en zone de champ très proche). Pour atteindre ces objectifs, nous avons défini quatre tâches principales : Développement d'un outil de synthèse de champ dans l'ouverture rayonnante (formulation théorique couplée à une méthode dite des projections alternées) ; développement d'un outil de calcul rapide (sur la base de traitements par FFT) du champ électromagnétique rayonné en zone de champ proche par une ouverture rayonnante, et retro-propagation ; hybridation de ces algorithmes avec un code de calcul (méthode des moments) en cours de développement à l'IETR et dédié à l'analyse très rapide d'antennes en technologie SIW ; conception d'une preuve ou plusieurs preuves de concept, et validations numérique et expérimentale des concepts proposés. / With the demand for near-field antennas continuously growing, the antenna engineer is charged with the development of new concepts and design procedures for this regime. From the microwave and up to terahertz frequencies, a vast number of applications, especially in the biomedical domain, are in need for focused or shaped fields in the antenna proximity. This work proposes new theoretical methods for near-field shaping based on different optimization schemes. Continuous radiating planar apertures are optimized to radiate a near field with required characteristics. In particular, a versatile optimization technique based on the alternating projection scheme is proposed. It is demonstrated that, based on this scheme, it is feasible to achieve 3-D control of focal spots generated by planar apertures. Additionally, with the same setup, also the vectorial problem (shaping the norm of the field) is addressed. Convex optimization is additionally introduced for near-field shaping of continuous aperture sources. The capabilities of this scheme are demonstrated in the context of different shaping scenarios. Additionally, the discussion is extended to shaping the field in lossy stratified media, based on a spectral Green's functions approach. Besides, the biomedical applications of wireless power transfer to implants and breast cancer imaging are addressed. For the latter, an extensive study is included here, which delivers an outstanding improvement on the penetration depth at higher frequencies. The thesis is completed by several prototypes used for validation. Four different antennas have been designed, based either on the radial line slot array topology or on metasurfaces. The prototypes have been manufactured and measured, validating the overall approach of the thesis.