The large carbon dioxides produced by highly developed industries not only result in serious air pollution and health problems, but also cause ocean acidification and decrease the survival rate of fry in aquaculture. Therefore, to develop a system for real-time detection of the concentration of carbon dioxide in aquaculture has become a very important research issue. Optical analysis and gas-chromatography are the two main methods adopted in conventional gas detection. Although the conventional carbon dioxide detectors presented high sensitivity and accuracy, the high fabrication cost, large dimension, low capability of batch fabrication and without real-time monitoring function will limit their applications. This thesis utilizes MEMS technology to implement an extended-gate field-effect transistor (EGFET) with an integrated gas permeable membrane for development of a high-sensitivity, small size and low cost carbon dioxide microsensor. The main material of the carbon dioxide gas permeable membrane adopted in this research is dioctyl sebacate. The main processing steps of the proposed microsensor include four photolithography and four thin-film deposition processes. In addition, the influences of the channel width/length ratio of EGFET and the coating of gas permeable membrane on the sensing performances of presented microsensor are also investigated in this study. The chip size of the implemented carbon dioxide microsensor is 11 mm¡Ñ13 mm¡Ñ 0.5 mm and the sensing area is 1 mm¡Ñ1 mm. As the carbon dioxide concentration varies from 0.25 mM to 50 mM, a very high sensitivity (42.3 mV/ppm) and sensing linearity (99.2%) of the proposed EGFET microsensor can be demonstrated. In addition, the response time of the presented carbon dioxide microsensor is only about 100 seconds, hence it is very suitable for developing a real-time monitoring microsystem.

[EN] The current PhD thesis deals with the development and characterization of novel nanocomposites based on biodegradable poly(mannitol sebacate) (PMS) matrices with tailored properties and shape-memory capabilities for biomedical applications. Two types of fillers -cellulose nanocrystals (CNC) and electrospun poly(lactic acid) nanofibers (NF-PLA)- were used as reinforcement in order to induce and/or enhance the shape-memory properties of PMS matrices. Also, different crosslinking profiles and stoichiometric ratios between mannitol and sebacic acid (1:1 and 1:2) were studied and evaluated to obtain samples with low and high degrees of crosslinking. An appropriate combination of the crosslinking profile and the monomer ratio for PMS matrix, as well as the addition of low content of CNC, allowed the development of PMS/CNC nanocomposites with a wide range of mechanical properties and degradation profiles. On the other hand, highly oriented poly(lactic acid) (PLA) nanofiber mats obtained by electrospinning were embedded in the PMS matrices. An enhancement of up to 53-fold in the Young's modulus was observed for PMS/NF-PLA nanocomposites filled with 15 wt% of PLA nanofibers. The incorporation of fillers (CNC and NF-PLA) allowed the development of thermally active shape-memory nanocomposites with an enhancement of parameters such as recovery stress and shape fixity. The electrospun PLA-reinforced nanocomposites, offered the best balance of mechanical and thermal properties, as well as a greater control of the transition temperature for switching the change of shape, within a useful range of temperatures. Owing to that, these materials may be of interest as smart responsive systems in long-term biomedical applications. / [ES] La presente tesis doctoral, se centra en el desarrollo y caracterización de nuevos nanocompuestos biodegradables, a partir de matrices de poli(mannitol sebacato) (PMS) con propiedades a medida y capacidades de memoria de forma para aplicaciones biomédicas. Dos tipos de cargas -nanocristales de celulosa (CNC) y nanofibras de ácido poliláctico (NF-PLA) obtenidas mediante electrospinning- se han utilizado como refuerzo, con la finalidad de inducir y/o mejorar las propiedades de memoria de forma en matrices de PMS. Se han estudiado y evaluado diferentes tratamientos de curado y ratios de reacción entre el mannitol y ácido sebácico (1:1 y 1:2), con la finalidad de obtener muestras con bajo y alto grado de reticulación. Una combinación adecuada del tratamiento de curado y el ratio entre monómeros del PMS, así como la adición de bajos contenidos de CNC, permitió desarrollar nanocompuestos de PMS/CNC con un amplio rango de propiedades mecánicas y perfiles de degradación. Por otro lado, se han producido mats de nanofibras de ácido poliláctico (PLA) con alta orientación mediante la técnica de electrospinning, para embeberse en matrices de PMS, observándose una mejora de hasta 53 veces en el módulo de Young para nanocompuestos de PMS/NF-PLA con un 15% en peso de nanofibras. La incorporación de cargas (CNC y NF-PLA) permitió el desarrollo de nanocompuestos con memoria de forma activada térmicamente, con una mejora de parámetros tales como la fuerza de recuperación y la capacidad de fijación. Los nanocompuestos reforzados con NF-PLA obtenidas por electrospinning, ofrecieron el mejor balance de propiedades mecánicas y térmicas, así como un mayor control de la temperatura de transición para la activación del cambio de forma en un intervalo útil de temperaturas. Por todo ello, estos materiales pueden resultar de interés como sistemas activos en aplicaciones biomédicas de larga duración. / [CAT] La present tesi doctoral se centra en el desenvolupament i caracterització de nous nanocompostos biodegradables a partir de matrius de poli(mannitol sebacato) (PMS) amb propietats a mesura i capacitats de memòria de forma per a aplicacions biomèdiques. Dos tipus de càrregues -nanocristals de cel·lulosa (CNC) i nanofibres d'àcid polilàctic (NF-PLA) obtingudes mitjançant electrospinning- s'han utilitzat com a reforç amb la finalitat d'induir i/o millorar les propietats de memòria de forma en matrius de PMS. S'han estudiat i avaluat diferents tractaments de curat i ràtios de reacció entre el mannitol i àcid sebàcic (1:1 i 1:2) amb la finalitat d'obtenir mostres amb baix i alt grau de reticulació. Una combinació adequada del tractament de curat i el ràtio entre monòmers del PMS, així com l'addició de baixos continguts de CNC, va permetre desenvolupar nanocompostos de PMS/CNC amb un ampli rang de propietats mecàniques i perfils de degradació. D'altra banda, s'han produït mats de nanofibres d'àcid polilàctic (PLA) amb alta orientació mitjançant la tècnica de electrospinning, per embeure's en matrius de PMS, observant-se una millora de fins a 53 vegades en el mòdul de Young per nanocompostos de PMS/NF-PLA amb un 15% en pes de nanofibres. La incorporació de càrregues (CNC i NF-PLA) va permetre el desenvolupament de nanocompostos amb memòria de forma activada tèrmicament, amb una millora de paràmetres tals com la força de recuperació i la capacitat de fixació. Els nanocompostos reforçats amb NF-PLA obtingudes per electrospinning, van oferir el millor balanç de propietats mecàniques i tèrmiques, així com un major control de la temperatura de transició per a l'activació del canvi de forma en un interval útil de temperatures. Per tot això, aquests materials poden resultar d'interés com a sistemes actius en aplicacions biomèdiques de llarga durada. / Sonseca Olalla, A. (2015). DEVELOPMENT OF SHAPE-MEMORY COMPOSITES BASED ON A BIODEGRADABLE POLYESTER ELASTOMER [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/54129 / TESIS

No description available.

Compliance mismatch is a significant hurdle to long-term patency in small-diameter arterial bypass grafts. Vascular tissue engineering has the potential to produce compliant, non-thrombogenic small-diameter grafts. However, current engineered grafts are relatively non-compliant, resulting in intimal hyperplasia and graft occlusion when subjected to arterial pressures. This research investigates the mechanical and biological properties of engineered constructs based on a biodegradable synthetic elastomer, poly(glycerol sebacate) (PGS). Several methods for fabricating porous PGS scaffolds in a tubular geometry were developed and compared. Adult baboon vascular cells were cultured in the scaffolds under various in vitro experimental conditions, including variations in initial cell seeding density, the type of scaffold used for culture, culture time, scaffold material, and hydrostatic pressure, and properties of the resultant constructs were compared. Scaffold fabrication using heat-shrinkable mandrels and glass tubes coated with hyaluronic acid significantly decreased tolerances of wall thickness and mechanical properties, improved handling, and decreased culture time required to reach luminal cellular confluence compared to scaffolds made with other fabrication techniques. Altering scaffold material from PGS to poly(lactide-co-glycolide) (PLGA), a benchmark biomaterial, did not affect scaffold yield, porosity, or luminal cellular confluence. Extracellular matrix (ECM) deposition increased with SMC-only culture time, and ECM deposition and remodeling during culture influenced construct compliance. Compared to PLGA scaffolds, PGS scaffolds promoted elastin crosslinking by SMCs and elastic tissue properties but attenuated collagen deposition. Hydrostatic pressure promoted ECM synthesis and deposition by SMCs and decreased construct compliance. Collagen and crosslinked elastin content in constructs correlated positively with construct burst pressure, and a negative correlation dependent on scaffold type was found between collagen content and construct compliance at low pressures. The systematic investigation of culture conditions in this research provides insights into the control of engineered blood vessel properties. The central hypothesis of this work, that grafts engineered from PGS scaffolds and adult vascular cells under biomimetic in vitro culture conditions can possess compliance comparable to autologous vessels, is true at pressures below 60 mmHg and demonstrates potential for PGS-based vascular tissue engineering. Overall, this work provides tools for engineering tubular soft tissues based on porous PGS scaffolds.

Several experiments were designed for utilization of fluorescence spectroscopy as a method of aerosol particle detection in a model of lungs. One of the experiments was to arranged use luminescent properties of DEHS (bis(2-ethylhexyl)decandioate) for calculating aerosol deposition. The outcome of this experiment was confirmation of clusters existence, which causes luminescence of DEHS. But the luminescence is not enough dependent on concentration and as such is not suitable for calculation of aerosol deposition. As the next experiment DEHS-fluorescein particles were generated by condensation monodisperse aerosol generator (CMAG), where water was used instead of isopropyl alcohol as a solvent. By this alteration the negative influence of DEHS was eliminated, which caused results refinements of aerosol deposition. Generation of fluorescein sodium salt particles by small-scale powder disperser (SSPD) was designed as a last experiment. The lower deposition efficiency measured by this method was caused by particles polydispersion. Photo records were used for documentation of Hot-spots. Outcomes of this study are new knowledge of fluorescence spectroscopy utilization for study of aerosol deposition and possibilities of fluorescent aerosol particles generation. Acquired data can serve for knowledge extension of possible detection methods for aerosol particles in the model of lung and can serve for validation of numerical simulations.

Regeneration, a spontaneous response of bones in response to injuries, infections and fractures, is severely compromised in certain clinical circumstances. Unfortunately, several shortcomings are associated with the current treatment of bone grafting method such as donor shortage and immune response for allografts and donor morbidity for autografts. Thus, the development of clinical alternates is essential. One promising adjunct method is bone tissue engineering that includes the implantation of a scaffold containing the cells with the supplementation of suitable growth factors. Among the various classes of materials, biodegradable polymers are commonly preferred because their use does not necessitate a secondary surgery for their removal after the intended use. Commercially available polymers such as poly (lactic- co- glycolic acid) and polycaprolactone are expensive and degrade slowly. This motivates the development of novel synthetic biodegradable polymers that are affordable and can be tuned to tailor for specific biomedical applications. The primary aim of this thesis is to synthesize effective biodegradable polymers for drug delivery and bone tissue engineering. The properties of these polymers such as modulus, hydrophobicity and crosslinking etc. were tailored based on the variations in chemical bonds, chain lengths and the molar stoichiometric ratios of the monomers for specific clinical applications. Based on the above variations, degradation and release kinetics were tuned. The cytocompatibilty properties for these polymers were studied and suitable mineralization studies were conducted to determine their potential for bone regeneration.