Advanced power semiconductor devices have consistently proven to be a major force in pushing the progressive development of power conversion technology. The emerging wide-band-gap (WBG) material based power semiconductor devices are considered as gaming changing devices which can exceed the limit of silicon (Si) and be used to pursue groundbreaking high-frequency, high-efficiency, and high-power-density power conversion. The switching performance of cascode GaN HEMT is studied at first. An accurate behavior-level simulation model is developed with comprehensive consideration of the impacts of parasitics. Then based on the simulation model, detailed loss breakdown and loss mechanism analysis are studied. The cascode GaN HEMT has high turn-on loss due to the reverse recovery charge and junction capacitor charge, and the common source inductance (CSI) of the package; while the turn-off loss is extremely small attributing to unique current source turn off mechanism of the cascode structure. With this unique feature, the critical conduction mode (CRM) soft switching technique is applied to reduce the dominant turn on loss and significantly increase converter efficiency. The switching frequency is successfully pushed to 5MHz while maintaining high efficiency and good thermal performance. Traditional packaging method is becoming a bottle neck to fully utilize the advantages of GaN HEMT. So an investigation of the package influence on the cascode GaN HEMT is also conducted. Several critical parasitic inductance are identified, which cause high turn on loss and high parasitic ringing that may lead to device failure. To solve the issue, the stack-die package is proposed to eliminate all critical parasitic inductance, and as a result, reducing turn on loss by half and avoiding potential failure mode of the cascode GaN device effectively. Utilizing soft switching and enhanced packaging, a GaN-based MHz totem-pole PFC rectifier is demonstrated with 99% peak efficiency and 700 W/in3 power density. The switching frequency of the PFC is more than ten times higher than the state-of-the-art industry product while it achieves best possible efficiency and power density. Integrated power module and integrated PCB winding coupled inductor are all studied and applied in this PFC. Furthermore, the technology of soft switching totem-pole PFC is extended to a bidirectional rectifier/inverter design. By using SiC MOSFETs, both operating voltage and power are dramatically increased so that it is successfully applied into a bidirectional on-board charger (OBC) which achieves significantly improved efficiency and power density comparing to the best of industrial practice. In addition, a novel 2-stage system architecture and control strategy are proposed and demonstrated in the OBC system. As a continued extension, the critical mode based soft switching rectifier/inverter technology is applied to three-phase AC/DC converter. The inherent drawback of critical mode due to variable frequency operation is overcome by the proposed new modulation method with the idea of frequency synchronization. It is the first time that a critical mode based modulation is demonstrated in the most conventional three phase H-bridge AC/DC converter, and with 99% plus efficiency at above 300 kHz switching frequency. / Ph. D. / Power electronics and power conversion are enabling technologies for almost any applications that are powered by electricity. It is very widely used in consumer electronics, household and industrial appliances, automobiles, utilities, infrastructures, and etc. It is essential but at the same time people want it to be invisible. Therefore the development of power electronics is consistently moving toward high efficiency (less and less energy waste), high density (small volume and less weight), high reliability, and low cost. Thanks to the development of silicon (Si) based semiconductor technology, especially silicon based power semiconductor devices, a great amount of achievements had been made in last three decades. However such high speed progress probably cannot be maintained for any longer since Si-based power devices are approaching their glass ceiling (theoretical limit) of what can be ultimately achieved. That is why people are looking for power devices made with material different than Si but with greater potential. Gallium Nitride (GaN) and Silicon Carbide (SiC) based power devices are chosen due to its great potential. It is believed to outperform Si-based devices by 2-3 orders which means power converters made with GaN and/or SiC can be even more efficient, smaller and lighter, more reliable, and of course with less cost. The most important approach to achieve such objective is high switching frequency. In order to turn the vision into reality, there are a lot of technology barriers in front of us, which in summary are how to understand the device and how to use the device into real applications with efficient high frequency operation. Therefore the major achievement of this work is comprehensive evaluation of GaN devices, and then demonstration of GaN and SiC in several AC/DC power converters for different applications. In the evaluation of GaN devices, an accurate simulation model was built and verified. Then based on the assistance of the model, switching loss mechanism is elaborated. The major conclusion is GaN has large turn on loss and very small turn off loss so that soft switching, which at least achieves zero-voltage-switching (ZVS) turn on, is important for GaN. Packaging related issues are addressed as well including analysis of package impacts on device performance and a new proposal of advanced package. It is very proud to claim that the proposal now are widely used by GaN device manufacturers into their real commercial products. After the know-how of how to use GaN was built, the potential of GaN was demonstrated in several different applications. The focus of this dissertation is on its application in AC/DC rectifier/inverter. Critical mode based totem-pole rectifier/inverter were built for 1 kW server power, 6.6 kW on board charger, and 25 kW solar inverter. A series of challenges were identified and the corresponding solutions were proposed. Today, the proposed design is becoming a benchmark and many of the industrial people are adopting our technology and applying it into real high performance products.

Fuel cells typically produce low-voltage high-current output because their individual cell voltage is low, and it is nontrivial to balance for a high-voltage stack. In addition, the output voltage of fuel cells varies depending on load conditions. Due to the variable low voltage output, the energy produced by fuel cells typically requires power conditioning systems to transform the unregulated source energy into more useful energy format. When evaluating power conditioning systems, efficiency and reliability are critical. The power conditioning systems should be efficient in order to prevent excess waste of energy. Since loss is dissipated as heat, efficiency directly affects system reliability as well. High temperatures negatively affect system reliability. Components are much more likely to fail at high temperatures. In order to obtain excellent efficiency and system reliability, low-voltage high-current power conditioning systems should be carefully designed. Low-voltage high-current systems require carefully designed PCB layouts and bus bars. The bus bar and PCB trace lengths should be minimized. Therefore, each needs to be designed with the other in mind. Excessive PCB and bus bar lengths can introduce parasitic inductances and resistances which are detrimental to system performance. In addition, thermal management is critical. High power systems must have sufficient cooling in order to maintain reliable operation. Many sources of loss exist for converters. For low-voltage high-current systems, conduction loss and switching loss may be significant. Other potential non-trivial sources of loss include magnetic losses, copper losses, contact and termination losses, skin effect losses, snubber losses, capacitor equivalent series resistance (ESR) losses, and body diode related losses. Many of the losses can be avoided by carefully designing the system. Therefore, in order to optimize efficiency, the designer should be aware of which components contribute significant amounts of loss. Loss analysis may be performed in order to determine the various sources of loss. The system efficiency can be improved by optimizing components that contribute the most loss. This thesis surveys some potential topologies suitable for low-voltage high-current systems. One low-voltage high-current system in particular is analyzed in detail. The system is called the V6, which consists of six phase legs, and is arranged as a three full-bridge phase-shift modulated converter to step-up voltage for distributed generation applications. The V6 converter has current handling requirements of up to 120A. Basic operation and performance is analyzed for the V6 converter. The loss within the V6 converter is modeled and efficiency is estimated. Calculations are compared with experimental results. Efficiency improvement through parasitic loss reduction is proposed by analyzing the losses of the V6 converter. Substantial power savings are confirmed with prototypes and experimental results. Loss analysis is utilized in order to obtain high efficiency with the V6 converter. Considerations for greater current levels of up to 400A are also discussed. The greater current handling requirements create additional system issues. When considering such high current levels, parallel devices or modules are required. Power stage design, layout, and bus bar issues due to the high current nature of the system are discussed. / Master of Science

Switched mode power supplies (SMPS) are being extensively used in most power conversion processes. The analysis, design and modeling processes of hard-switched converters are mature, where the switching frequency was limited to a few 10's of kHz. The present direction of evolution m SMPS is towards higher efficiency and higher power density. These twin objectives demand high switching frequency and low overall losses. Soft switching results in practically zero switching losses and extends the switching frequency to 100's of kHz and beyond. This thesis presents novel variants of push-pull and half-bridge DC-DC converters with soft switching properties. The proposed topology uses two additional switches and two diodes. The additional switches introduce freewheeling intervals m the circuit and enable loss-less switching. Switch stress, control and small signal model are similar to hard-switched PWM converter. Synchronous rectifiers are used in the ZVS push-pull converter to achieve high efficiency. It is interesting to see that the drives for the synchronous rectifier device are practically the same as the additional switches. The contributions made in this thesis are 1) Idealized analysis and design methodology for the proposed converters. 2) Validation of the design through circuit simulation as well as prototypes - a 300kHz, 200W push-pull converter and a 300kHz, 640W half-bridge converter. 3) Closed loop control design for desired bandwidth and accuracy Verification of loop gain through network analyzer instrumental for the same The loop gain bandwidth achieved is about 30kHz for the push-pull converter and 20kHz for half-bridge converter. An appendix has been devoted to explain the use of network analyzer. Characterization of coil, transformer and capacitor are explained in detail. Measurement techniques for measuring the small signal parameters of power supply are also explained in the appendix.

Dans l'aéronautique, l'alimentation d'un système embarqué contribue largement à augmenter le coût récurrent, l'efficacité globale et le volume de l'équipement. De plus, les alimentations sont installées dans un environnement sévère avec une large plage de tension d'entrée et un milieu confiné. Dans ces conditions, les pertes du convertisseur influent fortement sur le volume et le poids du système qui doit s'efforcer de limiter les échauffements. Ainsi, la réduction des pertes du convertisseur est l'un des leviers les plus efficaces pour augmenter la densité de puissance des convertisseurs. Parmi les techniques connues, la commutation douce peut être une solution pour réduire les pertes du convertisseur tout en augmentant sa fréquence de découpage. La sélection d'une topologie à commutation douce se fait selon 3 critères; un faible nombre de composants, une fonction de transfert et des commutations douces qui couvrent toute la plage de fonctionnement. En prenant tout cela en considération, la meilleure candidate semble être la topologie Flyback active-clamp. Avec seulement une capacité et un transistor supplémentaires, cette topologie possède une fonction abaisseuse et élévatrice et réalise des commutations en ZVS au primaire.Un travail technologique doit également être réalisé afin d'améliorer davantage l'efficacité du convertisseur. Les technologies qui ont été sélectionnées sont les transistors GaN pour leurs performances en commutation et le transformateur planar pour son intégration dans le PCB. Par ailleurs, une intégration verticale du convertisseur qui est à présent sur deux cartes superposées, une pour les fonctions BF et l'autre pour les fonctions HF, a permis de minimiser l'empreinte du convertisseur.Les technologies émergentes vont faire un important saut technologique, en particulier dans les systèmes où l'alimentation représente une part significative de l'équipement. Le succès des transistors GaN met clairement en lumière que l'électronique de puissance devient plus performante. Dans ce contexte, réduire les éléments parasites est une priorité. En se projetant dans le futur, l'intérêt porté aux alimentations intégrées va accélérer le développement des techniques de packaging telles que l'enfouissement des composants dans le PCB et les modules sur céramique / The power supply system in an onboard aeronautical application represents an important contribution to the recurring cost, global efficiency and the volume of the system. Moreover, power supplies are installed in a harsh environment with a wide input voltage range and a confined area. In these conditions, power supply losses impact the converter volume and weight to prevent the system from overheating. Therefore, a gain in efficiency is the main purposes, since it has a significant impact on the reduction of weight and volume of the equipment.Soft-switching is a reasonable technique to increase the switching frequency and limit the power losses. The selection of the topology should take into account 3 considerations: a low number of components, an efficient control, which allows to cover the wide input voltage range and a soft-switching validity over a large input voltage range. Regarding all the considerations, the Flyback active-Clamp topology seems to be the best candidate which has a step-up and down transfer function and ZVS at the primary with only ones additional capacitor and transistor.A technological work is also done to further increase the power supply efficiency. The technologies which have been selected are the GaN transistors for its good switching performances and a planar transformer for its integration into the PCB. Also, the vertical integration of the converter which is actually on two stackable boards, one for the low frequency functions and the other one for the high frequency functions, minimizes the footprint of the converter. The new technologies will make a huge technological leap, especially in the systems where the power supply represents a significant proportion of the equipment. The success of GaN transistor highlights that the power electronics is currently driving by the performance and reducing the parasitic elements is becoming the priority. Looking forward into the future, the interest in 3D packaging and PCB integration will grow rapidly to provide a fully embedded power supply

In this dissertation, new high frequency link power conversion systems for the fuel cell power conditioning are proposed to improve the performance and optimize the cost, size, and weight of the power conversion systems. The first study proposes a new soft switching technique for the phase-shift controlled bi-directional dc-dc converter. The described dc-dc converter employs a low profile high frequency transformer and two active full-bridge converters for bidirectional power flow capability. The proposed new soft switching technique guarantees soft switching over wide range from no load to full load without any additional circuit components. The load range for proposed soft switching technique is analyzed by mathematical approach with equivalent circuits and verified by experiments. The second study describes a boost converter cascaded high frequency link direct dc-ac converter suitable for fuel cell power sources. A new multi-loop control for a boost converter to reduce the low frequency input current harmonics drawn from the fuel cell is proposed, and a new PWM technique for the cycloconverter at the secondary to reject the low order harmonics in the output voltages is presented. The performance of the proposed scheme is verified by the various simulations and experiments, and their trade-offs are described in detail using mathematical evaluation approach. The third study proposes a current-fed high frequency link direct dc-ac converter suitable for residential fuel cell power systems. The high frequency full-bridge inverter at the primary generates sinusoidally PWM modulated current pulses with zero current switching (ZCS), and the cycloconverter at the secondary which consists of only two bidirectional switches and output filter capacitors produces sinusoidally modulated 60Hz split single phase output voltage waveforms with near zero current switching. The active harmonic filter connected to the input terminal compensates the low order input current harmonics drawn from the fuel cell without long-term energy storage devices such as batteries and super capacitors.

Recently, matrix converter has received considerable interest as a viable alternative to the conventional back-to-back PWM (Pulse Width Modulation) converter in the ac/ac conversion. This direct ac/ac converter provides some attractive characteristics such as: inherent four-quadrant operation; absence of bulky dc-link electrolytic capacitors; clean input power characteristics and increased power density. However, industrial application of the converter is still limited because of some practical issues such as common mode voltage effects, high susceptibility to input power disturbances and low voltage transfer ratio. This dissertation proposes several new matrix converter topologies together with control strategies to provide a solution about the above issues. In this dissertation, a new modulation method which reduces the common mode voltage at the matrix converter is first proposed. The new method utilizes the proper zero vector selection and placement within a sampling period and results in the reduction of the common mode voltage, square rms of ripple components of input current and switching losses. Due to the absence of a dc-link, matrix converter powered ac drivers suffer from input voltage disturbances. This dissertation proposes a new ride-through approach to improve robustness for input voltage disturbances. The conventional matrix converter is modified with the addition of ride-through module and the add-on module provides ride-through capability for matrix converter fed adjustable speed drivers. In order to increase the inherent low voltage transfer ratio of the matrix converter, a new three-phase high-frequency link matrix converter is proposed, where a dual bridge matrix converter is modified by adding a high-frequency transformer into dc-link. The new converter provides flexible voltage transfer ratio and galvanic isolation between input and output ac sources. Finally, the matrix converter concept is extended to dc/ac conversion from ac/ac conversion. The new dc/ac direct converter consists of soft switching full bridge dc/dc converter and three phase voltage source inverter without dc link capacitors. Both converters are synchronized for zero current/voltage switching and result in higher efficiency and lower EMI (Electro Magnetic Interference) throughout the whole load range. Analysis, design example and experimental results are detailed for each proposed topology.

In this dissertation, new high frequency link power conversion systems for the fuel cell power conditioning are proposed to improve the performance and optimize the cost, size, and weight of the power conversion systems. The first study proposes a new soft switching technique for the phase-shift controlled bi-directional dc-dc converter. The described dc-dc converter employs a low profile high frequency transformer and two active full-bridge converters for bidirectional power flow capability. The proposed new soft switching technique guarantees soft switching over wide range from no load to full load without any additional circuit components. The load range for proposed soft switching technique is analyzed by mathematical approach with equivalent circuits and verified by experiments. The second study describes a boost converter cascaded high frequency link direct dc-ac converter suitable for fuel cell power sources. A new multi-loop control for a boost converter to reduce the low frequency input current harmonics drawn from the fuel cell is proposed, and a new PWM technique for the cycloconverter at the secondary to reject the low order harmonics in the output voltages is presented. The performance of the proposed scheme is verified by the various simulations and experiments, and their trade-offs are described in detail using mathematical evaluation approach. The third study proposes a current-fed high frequency link direct dc-ac converter suitable for residential fuel cell power systems. The high frequency full-bridge inverter at the primary generates sinusoidally PWM modulated current pulses with zero current switching (ZCS), and the cycloconverter at the secondary which consists of only two bidirectional switches and output filter capacitors produces sinusoidally modulated 60Hz split single phase output voltage waveforms with near zero current switching. The active harmonic filter connected to the input terminal compensates the low order input current harmonics drawn from the fuel cell without long-term energy storage devices such as batteries and super capacitors.

This thesis presents a novel Zero Voltage Switching (ZVS) approach in a grid connected single-stage flyback inverter without using any additional auxiliary circuits. The soft-switching of the primary switch is achieved by allowing negative current from the grid-side through bidirectional switches placed on the secondary side of the transformer. Basically, the negative current discharges the MOSFET’s output capacitor thereby allowing turn-on of the primary switch under zero voltage. In order to optimize the amount of reactive current required to achieve ZVS a variable frequency control scheme is implemented over the line cycle. In addition, the bi-directional switches on the secondary side of the transformer have ZVS during the turn-on times. Therefore, the switching losses of the bi-directional switches are negligible. A 250W prototype has been implemented in order to validate the proposed scheme. Experimental results confirm the feasibility and superior performance of the converter compared to the conventional flyback inverter. / Thesis (Master, Electrical & Computer Engineering) -- Queen's University, 2012-07-06 16:24:13.385

Conselho Nacional de Desenvolvimento Científico e Tecnológico / This Ph. D. dissertation presents contributions to the investigation of soft-switching cells with integrated components, presenting three main approaches: (i) Soft-switching cells with filter coupled inductor; (ii) Integrated soft-switching cells of the ZVT type for multipole systems; and (iii) Integrated soft-switching cells for several soft-switching techniques for multipole systems. Firstly it is presented a generic diagram for softswitching inverters with coupled filter inductor. From the generic diagram the turn-on snubber, ZVT and ZCZVT inverters topologies are derived. It is based on an auxiliary loop, which presents an inductor coupled to the filter inductor. The magnetic coupling allows annulling the current through the main switches during the switching transitions and, as a result, reducing the commutation losses. The basic differences among the techniques obtained by this method are the way of implementing the auxiliary switches and the time instants when these switches are triggered. The topological variations are a result of the choice of the voltage applied through the auxiliary loop by its connection to the inverter topology. Analytical expressions for the derived topologies are obtained aiming to evaluate the operation conditions, as well the main features of each topology. It is proposed a design procedure for each derived topology and the operation principles of each topology are verified by means of experimental and simulation results. Then the integrated softswitching cells of the ZVT type for multipole systems are studied. The synthesis methodology presented is based on generating every topological possibility of symmetrical auxiliary cells. The redundant cells are removed from the set of generated topologies resulting in only four diagrams, which are used to derive the integrated ZVT converters already known in the literature, as well several yet unpublished. The synthesis methodology is applied on an interruptible power supply system, which is experimentally evaluated. Finally it is proposed a generalized methodology to obtain integrated auxiliary commutation cells from several soft-switching techniques concerning multipole systems. The integration possibilities among the models obtained for the chosen soft-switching techniques are investigated, resulting in integrated models. The practical implementation of the resulting models is studied originating integrated topologies for multipole systems. The poles of the system can present the same soft-switching technique or different ones. Experimental results are presented in order to validate the concepts proposed herein. / Esta tese de doutorado apresenta contribuições ao estudo de células de comutação suave com componentes integrados, apresentando três abordagens principais: (i) Células de comutação suave com indutor de filtro acoplado; (ii) Células de comutação suave integradas do tipo ZVT para sistemas multi-pólos; e (iii) Células de comutação suave integradas considerando-se diversas técnicas de comutação para sistemas multi-pólos. Inicialmente é apresentado um diagrama genérico para os conversores com comutação suave e indutor de filtro acoplado. A partir do diagrama genérico são derivadas topologias de inversores snubber de turn-on, ZVT e ZCZVT. Este diagrama genérico é baseado em uma malha auxiliar que apresenta um indutor acoplado ao indutor de filtro. O acoplamento magnético permite fazer com que a corrente através das chaves principais se anule durante as transições de comutação e, como resultado, ocorre a redução das perdas de comutação. A diferença básica entre as técnicas obtidas através deste método é o modo escolhido para implementar as chaves auxiliares e os instantes de acionamento das mesmas. As variações entre as topologias ocorrem em função da escolha da tensão aplicada à malha auxiliar. São obtidas expressões para as topologias derivadas no intuito de avaliar as condições de operação, bem como algumas de suas características. É proposto um procedimento de projeto e verificado o princípio de funcionamento destes inversores através de resultados experimentais e de simulação. A seguir são estudadas as células de comutação suave do tipo ZVT compartilhadas por sistemas que possuem múltiplos pólos. Esta metodologia de síntese é baseada na geração de todas as possibilidades de configurações para as células auxiliares simétricas. A partir disto, as configurações redundantes são eliminadas chegando-se a quatro diagramas capazes de gerar os conversores ZVT integrados presentes na literatura, bem como alguns ainda inéditos. A metodologia de síntese é aplicada para um sistema de fornecimento ininterrupto de energia, sendo que alguns resultados experimentais são apresentados. Finalmente é proposta uma metodologia generalizada para integrar as células auxiliares de diversas técnicas de comutação suave para conversores com múltiplos pólos. Partindo-se da obtenção de modelos para algumas das técnicas de comutação suave, procura-se verificar todas as possibilidades de combinação entre os modelos inicialmente obtidos, gerando-se modelos integrados e a partir disto, obtendo-se topologias integradas tanto para pólos que comutam auxiliados pela mesma técnica de comutação, como para pólos auxiliados por técnicas distintas. São apresentados resultados experimentais comprovando a viabilidade dos conceitos propostos.

abstract: This thesis investigates different unidirectional topologies for the on-board charger in an electric vehicle and proposes soft-switching solutions in both the AC/DC and DC/DC stage of the converter with a power rating of 3.3 kW. With an overview on different charger topologies and their applicability with respect to the target specification a soft-switching technique to reduce the switching losses of a single phase boost-type PFC is proposed. This work is followed by a modification to the popular soft-switching topology, the dual active bridge (DAB) converter for application requiring unidirectional power flow. The topology named as the semi-dual active bridge (S-DAB) is obtained by replacing the fully active (four switches) bridge on the load side of a DAB by a semi-active (two switches and two diodes) bridge. The operating principles, waveforms in different intervals and expression for power transfer, which differ significantly from the basic DAB topology, are presented in detail. The zero-voltage switching (ZVS) characteristics and requirements are analyzed in detail and compared to those of DAB. A small-signal model of the new configuration is also derived. The analysis and performance of S-DAB are validated through extensive simulation and experimental results from a hardware prototype. Secondly, a low-loss auxiliary circuit for a power factor correction (PFC) circuit to achieve zero voltage transition is also proposed to improve the efficiency and operating frequency of the converter. The high dynamic energy generated in the switching node during turn-on is diverted by providing a parallel path through an auxiliary inductor and a transistor placed across the main inductor. The paper discusses the operating principles, design, and merits of the proposed scheme with hardware validation on a 3.3 kW/ 500 kHz PFC prototype. Modifications to the proposed zero voltage transition (ZVT) circuit is also investigated by implementing two topological variations. Firstly, an integrated magnetic structure is built combining the main inductor and auxiliary inductor in a single core reducing the total footprint of the circuit board. This improvement also reduces the size of the auxiliary capacitor required in the ZVT operation. The second modification redirects the ZVT energy from the input end to the DC link through additional half-bridge circuit and inductor. The half-bridge operating at constant 50% duty cycle simulates a switching leg of the following DC/DC stage of the converter. A hardware prototype of the above-mentioned PFC and DC/DC stage was developed and the operating principles were verified using the same. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2017