This project explores the feasibility of the solid-state welding method direct-drive friction welding to be used as a joining method for the nitrogen alloyed steel Uddeholm Vanax SuperClean, produced via processes based on powder metallurgy. Vanax SuperClean cannot be welded using fusion welding methods where the base material melts, due to nitrogen escaping the material, resulting in inferior quality welds. The cost of the material motivates the use of Vanax SuperClean for critical parts in applications, combined with a less costly material for the remaining parts, causing alternative joining methods to be examined. Vanax SuperClean is friction welded to itself and to Uddeholm steel types Stavax ESR and UHB 11. Samples are prepared for a number of examinations. Microstructures of the samples are examined using microscopy, microhardness testing is carried out per the Vickers principle, retained austenite is measured using X-ray diffraction and tensile testing of the welded samples is performed. Defect-free welds are produced in all examined samples, showing that the method is suitable for Vanax SuperClean and that no preheating or slow cooling of workpieces are necessary. The possibility of using friction stir welding as a joining method for Vanax SuperClean is discussed. / Detta projekt undersöker möjligheten att använda trycksvetsningsmetoden friktionssvetsning som sammanfogningsmetod för det kvävelegerade pulvermetallurgiskt framställda stålet Uddeholm Vanax SuperClean. Vanax SuperClean kan inte svetsas med smältsvetsmetoder där grundmaterialet smälter, på grund av kvävgasbildning som resulterar i undermåliga svetsfogar. Kostnaden för materialet motiverar användandet av Vanax SuperClean för kritiska delar i applikationer, kombinerat med ett mindre kostsamt material till övriga delar, vilket föranleder undersökning av alternativa sammanfogningsmetoder. Vanax SuperClean friktionssvetsas mot sig själv, såväl som mot Uddeholmsstålen Stavax ESR och UHB 11. Prov tas fram för ett antal undersökningar. Mikrostruktur undersöks med mikroskopi, mikrohårdhetsprovning utförs enligt Vickersprincipen, restaustenitnivåer mäts med röntgendiffraktion och dragprovning utförs. Lyckade svetsfogar fås i alla undersökta prover, vilket visar att svetsmetoden är lämplig för Vanax SuperClean och att varken förvärmning eller långsamt svalnande av arbetsstycken krävs. Möjligheten att använda friktionsomrörningssvetsning som sammanfogningsmetod för Vanax SuperClean diskuteras.

Friction bit joining (FBJ) is a new solid-state spot joining technology developed in cooperation between Brigham Young University of Provo Utah, and MegaStir Technologies of West Bountiful Utah. Although capable of joining several different material combinations, this research focuses on the application of FBJ to joining 5754 aluminum to DP 980 steel, two alloys commonly used in automotive applications. The thicknesses of the materials used were 0.070 inches (1.78 mm) and 0.065 inches (1.65 mm), respectively. The FBJ process employs a consumable 4140 steel bit and is carried out on a purpose built research machine. In the first stage of the weld cycle the bit is used to drill through the aluminum top sheet to be joined. After this, spindle speed is increased so that the bit tip effectively forms a friction weld to the steel bottom sheet. Momentary stoppage of the spindle facilitates weld cooling before the spindle is restarted, shearing the bit tip from the bit shank, and retracted. Incorporated into the bit tip geometry is a flange that securely holds the aluminum in place after joint formation is complete. This research consists of several developmental steps since the technology only recently began to be formally studied. Initial joint strengths observed in lapshear tensile testing averaged only 978.5 pounds (4.35 kN), with a relatively high standard deviation for the data set. Final lapshear tensile test results were improved to an average of 1421.8 pounds (6.32 kN), with a significantly lower, and acceptable, standard deviation for the data set. Similar improvements were realized during the development work in cross tension tensile test results, as average strengths increased from 255.8 pounds (1.14 kN) to 566.3 pounds (2.52 kN). Improvements were also observed in the standard deviation values of cross tension data sets from initial evaluation to the final data set presented in this work.