Made available in DSpace on 2016-06-02T19:12:29Z (GMT). No. of bitstreams: 1 5246.pdf: 9799013 bytes, checksum: 4c1e1a4d482b5bbe3c75535359168a82 (MD5) Previous issue date: 2012-10-05 / Universidade Federal de Minas Gerais / Polymeric components have been replacing traditional materials such as glass or metals in a wide range of applications due to their advantages, such as optimized specific strength (weight-to-strength ratio), reduced fabrication time and costs, and design flexibility. The increasing use of polymeric materials in engineering requires efficient and environmental friendly fabrication and processing technologies. Initially developed for metals, the Friction Stir Spot Welding (FSSW) is a joining technique with short process cycles, low energy consumption and no need of consumables. Friction Stir Spot Welding has excellent performance in welding of lightweight alloys, showing promising results in thermoplastic welding. This study investigates the relationships between friction stir spot welding parameters (tool rotational speed, plunge rate and dwell time) and weld properties (joint geometry, process temperature, microstructure, lap shear resistance and failure mechanisms) in polymethylmethacrylate (also known as PMMA) single-spot joints. PMMA friction stir spot welds showed similar mechanical performance in comparison to other current welding techniques, with equal or shorter welding cycle times. Differential scanning calorimetry and gel permeation chromatography analysis demonstrated that polymer degradation level in the weld region was negligible. The statistical models proposed for FSSW of PMMA showed good repeatability and reproducibility for the investigated material and welding ranges. Moreover, the feasibility of the Friction Spot Welding (FSpW) a new joining technology developed as a further improvement of the friction stir spot welding was successfully demonstrated in thermoplastic polymers for the first time worldwide. Sound FSpW-single lap joints on PMMA were produced and their properties studied within an exploratory study. / A busca por eficiência econômica e tecnologias ecologicamente corretas tem sido observada em praticamente todos os setores da produção industrial, desde o desenvolvimento de materiais, design de produtos e inclusive na área da soldagem. A soldagem ponto por fricção e mistura mecânica, FSSW (do inglês Friction Stir Spot Welding) e a Friction Spot Welding FSpW são técnicas de soldagem recentes e que têm sido amplamente empregadas na união de ligas metálicas leves, em que as soldas geralmente apresentam excelentes propriedades mecânicas. Além disso, ciclos de soldagem curtos, baixo consumo de energia e ausência de necessidade de adição de material ou elementos de soldagem são características positivas encontradas nesses novos processos. Na área de materiais poliméricos, entretanto, este é um novo e promissor assunto. Neste trabalho buscou-se investigar a relação entre os parâmetros do processo de soldagem por FSSW (velocidade de rotação da ferramenta, taxa de penetração e tempo de recalque) e as propriedades das juntas (geometria da solda, máxima temperatura processual, área afetada termicamente, resistência mecânica ao cisalhamento sob tensão e mecanismos de fratura) em placas de poli (metacrilato de metila). Foi possível observar a formação de juntas com resistência mecânica ao cisalhamento semelhante a outros processos atualmente utilizados na indústria, com tempos de ciclo de soldagem iguais ou inferiores a esses processos. As análises via calorimetria diferencial exploratória (DSC) e cromatografia por permeação em gel (GPC) demonstraram que os níveis de degradação termomecânica encontrados nas amostras foram insignificantes. A modelagem estatística do processo demonstrou a boa repetibilidade e reprodutibilidade dentro das condições estudadas. Nesse trabalho, também foi investigado através de um estudo exploratório, pela primeira vez, a viabilidade da nova técnica FSpW na soldagem de termoplásticos, demonstrando, com sucesso, a capacidade de obtenção de juntas de boa qualidade em PMMA.

In this study tools consisting of a 5mm cylindrical pin and a 12mm shoulder held by a simple tool holder were used to compare the wear of 11 tooling materials. The objective was to determine if using these tools in a spot welding configuration to simulate friction stir welding could differentiate the potential performance of tooling materials. All tools were made of varying percentages of polycrystalline cubic boron nitride (PCBN), tungsten (W) and rhenium (Re). The materials are referred to herein as GV1, GV2, G1, G2, G3, G4, G5, G6, G7, G8 and G9.The tools were run to 205 welds if they did not fracture first. The grades averaged the following quantities of welds before fracture failure GV-1:0; GV-2:200; G1:82; G2:204; G3:205; G4:205; G5:96; G7:102.73; G8:21.2; G9:38.5. Of the tools that ran the full 205 welds without chipping, the average calculated volume loss, which was the best indication of wear, was as follows G2:1.83%; G3:2.53%; G4:2.41%; G5:1.93%; and G7:2.30%.The study showed that G2 had the least wear and G6 had the most wear, of those tools that completed all 205 spot welds. Fracture was the failure mode of all grades with over 70% CBN content. It was found that small CBN grain size was not correlated to better wear performance, as has been seen in a prior study.

Friction stir spot welding (FSSW) is quickly becoming a method of interest for welding of high strength steel (HSS) and ultra high strength steel (UHSS). FSSW has been shown to produce high quality welds in these materials, without the drawbacks associated with fusion welding. Tool grade for polycrystalline cubic boron nitride (PCBN) tools has a significant impact on wear resistance, weld quality, and tool failure in FSSW of DP 980 steel sheet. More specifically, for a nominal composition of 90% CBN, the grain size has a significant impact on the wear resistance of the tool. A-type tools performed the best, of the three grades that were tested in this work, because the grain size of this grade was the finest, measuring from 3-6 microns. The effect of fine grain size was less adhesion of DP 980 on the tool surface over time, less abrasive wear, and better lap shear fracture loads of the welds that were produced, compared to the other grades. This is explained by less exposure of the binder phase to wear by both adhesion and abrasion during welding of DP 980. A-type tools were the most consistent in both the number of welds per tool, and the number of welds that reached acceptable lap shear fracture loads. B-type tools, with a bimodal grain size distribution (grain size of 4 – 40 microns) did a little bit better than C-type tools (grain size of 12-15 microns) in terms of wear, but neither of them were able to achieve consistent acceptable lap shear fracture load values after the first 200 welds. In fact only one out of five C-type tools was able to produce acceptable lap shear fracture loads after the first 100 welds.

Friction stir spot welding (FSSW) is a solid-state welding process which is especially useful for joining precipitation-hardened aluminium alloys that undergo adverse property changes during fusion welding. It also has potential as an effective method for solid-state joining of dissimilar alloys. In FSSW, heat generation and plastic flow are strongly linked, and the scale of the process in time and space is such that it is difficult to separate and control the influence of all the relevant input parameters. The use of modelling is well-established in the field of welding research, and this thesis presents an analysis of the thermal and mechanical aspects of FSSW, principally using the finite element (FE) technique. Firstly, a thermal FE model is shown, which is subsequently validated by reference to experimental temperature data in both aluminium-to-aluminium and aluminium-to-steel welds. Correlations between high-quality welds and temperature fields are established, and predictions are made for peak temperatures reached under novel welding conditions. Deformation and heating are strongly linked in FSSW, but existing modelling tools are poorly suited to modelling flow processes in the conditions extant in FSSW. This thesis discusses the development and optimisation of two novel techniques to overcome the limitations of current approaches. The first of these uses greatly simplified constitutive behaviour to convert the problem into one defined purely by kinematics. In doing so, the boundary conditions reduce to a small number of assumptions about the contact conditions between weld material and tool, and the model calculation time is very rapid. This model is used to investigate changes in the slip condition at the tool to workpiece interface without an explicit statement of the friction law. Marker experiments are presented which use dissimilar composition but similar strength alloys to visualise flow patterns. The layering behaviour and surface patterns observed in the model agree well with observations from these experiments. The second approach extends the FE method to include deformation behaviour without the need for a fully-coupled approach, guided by the kinematic model. This is achieved using an innovative sequential small-strain analysis method in which thermal and deformation analyses alternate, with each running at a very different timescale. This technique avoids the requirement to either remesh the model domain at high strains or to use an explicit integration scheme, both of which impose penalties in calculation time and model complexity. The method is used to relate the purely thermal analysis developed in the work on thermal modelling to welding parameters such as tool speed. The model enables predictions of the spatial and temporal evolution of heat generation to be made directly from the constitutive behaviour of the alloy and the assumed velocity profile at the tool-workpiece interface. Predictions of the resulting temperature history are matched to experimental data and novel conditions are simulated, and these predictions correlate accurately with experimental results. Hence, the model is used to predict welding outcomes for situations for which no experimental data exists, and process charts are produced to describe optimum welding parameters. The methods and results presented in this thesis have significant implications for modelling friction stir spot welding, from optimising process conditions, to integration with microstructural models (to predict softening in the heat-affected zone, or the formation of intermetallics at the interface in dissimilar welds). The technique developed for sequential small strain finite element analysis could also be investigated for use in other kinematically constrained solid-state friction joining processes.

Efforts to reduce vehicle weight and improve crash performance have resulted in increased application of advanced high strength steels (AHSS) and a recent focus on the weldability of these alloys. Resistance spot welding (RSW) is the primary sheet metal welding process in the manufacture of automotive assemblies. Integration of AHSS into the automotive architecture has brought renewed challenges for achieving acceptable welds. The varying alloying content and processing techniques has further complicated this initiative. The current study examines resistance spot welding of high strength and advance high strength steels including high strength low alloy (HSLA), dual phase (DP) and a ferritic-bainitic steel (590R). The mechanical properties and microstructure of these RSW welded steel alloys are detailed. Furthermore a relationship between chemistries and hardness is produced. The effect of strain rate on the joint strength and failure mode is also an important consideration in the design of welded structures. Current literature, however, does not explain the effects of weld microstructure and there are no comprehensive comparisons of steels. This work details the relationship between the joint microstructure and impact performance of spot welded AHSS. Quasi-static and impact tests were conducted using a universal tensile tester and an instrumented drop tower, respectively. Results for elongation, failure load and energy absorption for each material are presented. Failure modes are detailed by observing weld fracture surfaces. In addition, cross-sections of partially fractured weldments were examined to detail fracture paths during static loading. Correlations between the fracture path and mechanical properties are developed using observed microstructures in the fusion zone and heat-affected-zone. Friction stir spot welding (FSSW) has proven to be a potential candidate for spot welding AHSS. A comparative study of RSW and FSSW on spot welding AHSS has also been completed. The objective of this work is to compare the microstructure and mechanical properties of Zn-coated DP600 AHSS (1.2mm thick) spot welds conducted using both processes. This was accomplished by examining the metallurgical cross-sections and local hardnesses of various spot weld regions. High speed data acquisition was also used to monitor process parameters and attain energy outputs for each process.

Efforts to reduce vehicle weight and improve crash performance have resulted in increased application of advanced high strength steels (AHSS) and a recent focus on the weldability of these alloys. Resistance spot welding (RSW) is the primary sheet metal welding process in the manufacture of automotive assemblies. Integration of AHSS into the automotive architecture has brought renewed challenges for achieving acceptable welds. The varying alloying content and processing techniques has further complicated this initiative. The current study examines resistance spot welding of high strength and advance high strength steels including high strength low alloy (HSLA), dual phase (DP) and a ferritic-bainitic steel (590R). The mechanical properties and microstructure of these RSW welded steel alloys are detailed. Furthermore a relationship between chemistries and hardness is produced. The effect of strain rate on the joint strength and failure mode is also an important consideration in the design of welded structures. Current literature, however, does not explain the effects of weld microstructure and there are no comprehensive comparisons of steels. This work details the relationship between the joint microstructure and impact performance of spot welded AHSS. Quasi-static and impact tests were conducted using a universal tensile tester and an instrumented drop tower, respectively. Results for elongation, failure load and energy absorption for each material are presented. Failure modes are detailed by observing weld fracture surfaces. In addition, cross-sections of partially fractured weldments were examined to detail fracture paths during static loading. Correlations between the fracture path and mechanical properties are developed using observed microstructures in the fusion zone and heat-affected-zone. Friction stir spot welding (FSSW) has proven to be a potential candidate for spot welding AHSS. A comparative study of RSW and FSSW on spot welding AHSS has also been completed. The objective of this work is to compare the microstructure and mechanical properties of Zn-coated DP600 AHSS (1.2mm thick) spot welds conducted using both processes. This was accomplished by examining the metallurgical cross-sections and local hardnesses of various spot weld regions. High speed data acquisition was also used to monitor process parameters and attain energy outputs for each process.

Friction bit joining (FBJ) is a new solid-state spot joining technology developed in cooperation between Brigham Young University of Provo Utah, and MegaStir Technologies of West Bountiful Utah. Although capable of joining several different material combinations, this research focuses on the application of FBJ to joining 5754 aluminum to DP 980 steel, two alloys commonly used in automotive applications. The thicknesses of the materials used were 0.070 inches (1.78 mm) and 0.065 inches (1.65 mm), respectively. The FBJ process employs a consumable 4140 steel bit and is carried out on a purpose built research machine. In the first stage of the weld cycle the bit is used to drill through the aluminum top sheet to be joined. After this, spindle speed is increased so that the bit tip effectively forms a friction weld to the steel bottom sheet. Momentary stoppage of the spindle facilitates weld cooling before the spindle is restarted, shearing the bit tip from the bit shank, and retracted. Incorporated into the bit tip geometry is a flange that securely holds the aluminum in place after joint formation is complete. This research consists of several developmental steps since the technology only recently began to be formally studied. Initial joint strengths observed in lapshear tensile testing averaged only 978.5 pounds (4.35 kN), with a relatively high standard deviation for the data set. Final lapshear tensile test results were improved to an average of 1421.8 pounds (6.32 kN), with a significantly lower, and acceptable, standard deviation for the data set. Similar improvements were realized during the development work in cross tension tensile test results, as average strengths increased from 255.8 pounds (1.14 kN) to 566.3 pounds (2.52 kN). Improvements were also observed in the standard deviation values of cross tension data sets from initial evaluation to the final data set presented in this work.