The demand for energy to sustain the economies of industrialized and developing nations has led to the search for alternatives to the use of imported petroleum fuels. Instability in the Middle Eastern countries, the major exporting sources for these petroleum feedstocks, has led to questions of availability in addition to the economic issues. While coal and nuclear technologies are currently the leading sources for reduction of petroleum imports, wood and other biomass feedstocks have garnered attention as to their potential as additional alternatives. Studies have shown that the amount of biomass waste resources in the United States, if converted effectively, could significantly reduce the need for petroleum imports. The focus of this research is to examine a patented, entrained flow, steam gasification process for the ability to produce gaseous components suitable for use as a fuel or in subsequent conversion processes, such as production of alcohol or diesel. The primary gases which are examined are hydrogen, carbon monoxide, carbon dioxide, and methane. The process is characterized using a nominal 3 ton (wood) per day “pre-pilot” facility and a nominal 30 ton (wood) per day “pilot” unit. Each of these gasification systems are characterized for production of primary gases using wood as the feedstock. As part of these characterizations, “equivalent” temperatures and residence times were developed that better described the process operations. An important consideration in the development of any industrial process is the ability to scale-up from a conceptual, or preliminary, scale to a size capable of commercial operation. As such, the characterizations of the two gasification systems were compared and relationships were developed to allow predictions of product gas compositions based on gasifier size as well as operating parameters.

La possibilité de produire un gaz combustible (syngaz) à partir des composés carbonés outre que le charbon et le pétrole permettrait aux pays pauvres en ressources énergétiques de se diriger vers une indépendance énergétique.La vapogazéification est un procédé qui permet de produire un gaz riche en hydrogène à partir des matériaux carbonés (par exemple le char de biomasse) et de la vapeur d’eau. Etant donné que la gazéification est un processus endothermique, la source d’énergie est le premier souci à résoudre. Si l’on ne veut pas contribuer au réchauffement de la planète, la source d’énergie et de carbone doivent rester renouvelables. Jusqu’à présent, les ingénieurs concevaient les gazéifieurs en pensant à une uniformité des propriétés à l’intérieur du réacteur, cela simplifie la modélisation et le contrôle des variables, cependant, avec les sources de chaleur innovantes et la possibilité de n’utiliser que de la vapeur d’eau pour la gazéification, on peut conclure qu’un gradient de températures améliore la production d’hydrogène. Les nouvelles technologies de gazéification nécessitent donc une compréhension des phénomènes de transfert afin d’être améliorées et optimisées. Trois types de réacteurs ont modélisés dans le cadre de cette thèse, il est mis en évidence qu’il existe un manque de critères solides à l’heure de choisir le dispositif réactionnel le plus adéquat selon les ressources disponibles. La théorie du gradient de température est conçue à partir des principaux résultats de cette thèse et s’intéresse à la création d’un outil simple à utiliser pour que l’ingénieur puisse prendre des décisions qui aident à améliorer la production de gaz combustible. / The possibility of producing syngas from carbon compounds other than coal or oil would allow countries lacking energy resources to move toward energy independence. The steam gasification is a process that could help to this predisposition, producing a hydrogen-rich gas from carbon-rich materials (e.g. biomass char) and steam. Since gasification is an endothermic process, the energy source is the first concern to be addressed in the gasifierdesign. If we want it to not contribute to global warming, the energy source and carbon must remain renewable.Until now, engineers designed gasifiers thinking about uniformity of properties within the reactor, it simplifies the variables modeling and control, however, with innovative heat sources and the possibility to use only steamfor gasification, it can be concluded that a temperature gradient enhances the hydrogen production, thus the syngas quality is improved. The new gasification technologies therefore require the understanding of transport phenomena to apply this advantage in order to improve the syngas production and quality. Three reactor typesare modeled as part of this work, it is shown that there is a lack of firm criteria to choose the reaction device according to the resources, consequently, the reactors performance could be diminished if the energy source is not properly used. The theory of the temperature gradient is built based on the main results and it is a simple toolto help the engineer to make decisions that will improve the fuel gas production.

Glycerol is a waste by-product obtained during the production of biodiesel. Biodiesel is one of the alternative fuels used to meet our energy requirements and also carbon dioxide emission is much lesser when compared to regular diesel fuel. Biodiesel and glycerol are produced from the transesterification of vegetable oils and fats with alcohol in the presence of a catalyst. About 10 wt% of vegetable oil is converted into glycerol during the transesterification process. An increase in biodiesel production would decrease the world market price of glycerol. The objective of this work is to produce value added products such as hydrogen or syn gas and medium heating value gas from waste glycerol using pyrolysis and steam gasification processes. <p> Pyrolysis and steam gasification of glycerol reactions was carried out in an Inconel®, tubular, fixed bed down-flow reactor at atmospheric pressure. The effects of carrier gas flow rate (30mL/min-70mL/min), temperature (650oC-800oC) and different particle diameter of different packing material (quartz - 0.21-0.35mm to 3-4mm; silicon carbide 0.15 to 1mm; Ottawa sand 0.21-0.35mm to 1.0-1.15mm) on the product yield, product gas volume, composition and calorific value were studied for the pyrolysis reactions. An increase in carrier gas flow rate did not have a significant effect on syn gas production at 800oC with quartz chips diameter of 3-4mm. However, total gas yield increased from 65 to 72wt% and liquid yield decreased from 30.7 to 19.3wt% when carrier gas flow rate decreased from 70 to 30mL/min. An increase in reaction temperature, increased the gas product yield from 27.5 to 68wt% and hydrogen yield from 17 to 48.6mol%. Also, syn gas production increased from 70 to 93 mol%. A change in particle size of the packing material had a significant increase in the gas yield and hydrogen gas composition. Therefore, pyrolysis reaction at 800oC, 50mL/min of nitrogen and quartz particle diameter of 0.21-0.35mm were optimum reaction parameter values that maximise the gas product yield (71wt%), hydrogen yield (55.4mol%), syn gas yield (93mol%) and volume of product gas (1.32L/g of glycerol). The net energy recovered at this condition was 111.18 kJ/mol of glycerol fed. However, the maximum heating value of product gas (21.35 MJ/m3) was obtained at 650oC, 50mL/min of nitrogen and with a quartz packing with particle diameter of 3-4mm. <p>The steam gasification of glycerol was carried out at 800oC, with two different packing materials (0.21-0.35mm diameter of quartz and 0.15mm of silicon carbide) by changing the steam to glycerol weight ratio from 0:100 to 50:50. The addition of steam to glycerol increased the hydrogen yield from 55.4 to 64mol% and volume of the product gas from 1.32L/g for pyrolysis to 1.71L/g of glycerol. When a steam to glycerol weight ratio of 50:50 used for the gasification reaction, the glycerol was completely converted to gas and char. Optimum conditions to maximize the volume of the product gas (1.71L/g), gas yield of 94wt% and hydrogen yield of 58mol% were 800oC, 0.21-0.35mm diameter of quartz as a packing material and steam to glycerol weight ratio of 50:50. Syn gas yield and calorific value of the product gas at this condition was 92mol% and 13.5MJ/m3, respectively. The net energy recovered at this condition was 117.19 kJ/mol of glycerol fed. <p>The steam gasification of crude glycerol was carried out at 800oC, quartz size of 0.21-0.35mm as a packing material over the range of steam to crude glycerol weight ratio from 7.5:92.5 to 50:50. Gasification reaction with steam to glycerol weight ratio of 50:50 was the optimum condition to produce high yield of product gas (91.1wt%), volume of gas (1.57L/g of glycerol and methanol), hydrogen (59.1mol%) and syn gas (79.1mol%). However, the calorific value of the product gas did not change significantly by increasing the steam to glycerol weight ratio.

Glycerol is a waste by-product obtained during the production of biodiesel. Biodiesel is one of the alternative fuels used to meet our energy requirements and also carbon dioxide emission is much lesser when compared to regular diesel fuel. Biodiesel and glycerol are produced from the transesterification of vegetable oils and fats with alcohol in the presence of a catalyst. About 10 wt% of vegetable oil is converted into glycerol during the transesterification process. An increase in biodiesel production would decrease the world market price of glycerol. The objective of this work is to produce value added products such as hydrogen or syn gas and medium heating value gas from waste glycerol using pyrolysis and steam gasification processes. <p> Pyrolysis and steam gasification of glycerol reactions was carried out in an Inconel®, tubular, fixed bed down-flow reactor at atmospheric pressure. The effects of carrier gas flow rate (30mL/min-70mL/min), temperature (650oC-800oC) and different particle diameter of different packing material (quartz - 0.21-0.35mm to 3-4mm; silicon carbide 0.15 to 1mm; Ottawa sand 0.21-0.35mm to 1.0-1.15mm) on the product yield, product gas volume, composition and calorific value were studied for the pyrolysis reactions. An increase in carrier gas flow rate did not have a significant effect on syn gas production at 800oC with quartz chips diameter of 3-4mm. However, total gas yield increased from 65 to 72wt% and liquid yield decreased from 30.7 to 19.3wt% when carrier gas flow rate decreased from 70 to 30mL/min. An increase in reaction temperature, increased the gas product yield from 27.5 to 68wt% and hydrogen yield from 17 to 48.6mol%. Also, syn gas production increased from 70 to 93 mol%. A change in particle size of the packing material had a significant increase in the gas yield and hydrogen gas composition. Therefore, pyrolysis reaction at 800oC, 50mL/min of nitrogen and quartz particle diameter of 0.21-0.35mm were optimum reaction parameter values that maximise the gas product yield (71wt%), hydrogen yield (55.4mol%), syn gas yield (93mol%) and volume of product gas (1.32L/g of glycerol). The net energy recovered at this condition was 111.18 kJ/mol of glycerol fed. However, the maximum heating value of product gas (21.35 MJ/m3) was obtained at 650oC, 50mL/min of nitrogen and with a quartz packing with particle diameter of 3-4mm. <p>The steam gasification of glycerol was carried out at 800oC, with two different packing materials (0.21-0.35mm diameter of quartz and 0.15mm of silicon carbide) by changing the steam to glycerol weight ratio from 0:100 to 50:50. The addition of steam to glycerol increased the hydrogen yield from 55.4 to 64mol% and volume of the product gas from 1.32L/g for pyrolysis to 1.71L/g of glycerol. When a steam to glycerol weight ratio of 50:50 used for the gasification reaction, the glycerol was completely converted to gas and char. Optimum conditions to maximize the volume of the product gas (1.71L/g), gas yield of 94wt% and hydrogen yield of 58mol% were 800oC, 0.21-0.35mm diameter of quartz as a packing material and steam to glycerol weight ratio of 50:50. Syn gas yield and calorific value of the product gas at this condition was 92mol% and 13.5MJ/m3, respectively. The net energy recovered at this condition was 117.19 kJ/mol of glycerol fed. <p>The steam gasification of crude glycerol was carried out at 800oC, quartz size of 0.21-0.35mm as a packing material over the range of steam to crude glycerol weight ratio from 7.5:92.5 to 50:50. Gasification reaction with steam to glycerol weight ratio of 50:50 was the optimum condition to produce high yield of product gas (91.1wt%), volume of gas (1.57L/g of glycerol and methanol), hydrogen (59.1mol%) and syn gas (79.1mol%). However, the calorific value of the product gas did not change significantly by increasing the steam to glycerol weight ratio.

The aim of this diploma thesis is to describe the gasification of biomass with a mixture of oxygen and water vapor. The theoretical part is focused on the gasification process, gasification reactors and the quality of the resulting gas. In the experimental part we look for the ideal ratio of oxygen to water vapor, which are used as gasification media. Subsequent measurements are carried out on the fluidized bed reactor, the results of which are further processed and evaluated.

An investigation was undertaken to compare the kinetics of combustion and gasification reactions of chars prepared from two South African coals in different reaction atmospheres: air, steam, and carbon dioxide. The two original coals were characterised as vitrinite-rich (Greenside) and inertinite-rich (Inyanda) coals with relatively low ash content (12.5-16.7 wt. %, adb). Chars were prepared from the parent coals under nitrogen atmosphere at 900 °C. Characterisation results show that the volatiles and moisture were almost completely driven off from the parent coals, indicating that the pyrolysis process was efficient. Physicalstructural properties such as porosity and surface area generally increased from the parent coals to the subsequent chars. The heterogeneous char-gas reactions were conducted isothermally in a TGA on ~1 mm size particles. To ensure that the reactions are under chemical reaction kinetic control regime, different temperatures zones were selected for the three different reaction atmospheres. Combustion reactivity experiments were carried out with air in the temperature range of 387 °C to 425 °C; gasification reactivity with pure steam were conducted at higher temperatures (775 °C - 850 °C) and within 825 °C to 900 °C with carbon dioxide. Experimental results show differences in the specific reaction rate with carbon conversion in different reaction atmospheres and char types. Reaction rates in all three reaction atmospheres were strongly dependent on temperature, and follow the Arrhenius type kinetics. All the investigated reactions (combustion with air and gasification with CO2 and steam) were found to be under chemical reaction control regime (Regime I) for both chars. The inertinite-rich coals exhibit longer burn-out time than chars produced from vitrinite-rich coals, as higher specific reaction rate were observed for the vitrinite-rich coals in the three different reaction atmospheres. The determined random pore model (RPM) structural parameters did not show any significant difference during steam gasification of Greenside and Inyanda chars, whereas higher structural parameter values were observed for Greenside chars during air combustion and CO2 gasification (ψ > 2). However a negative ψ value was determined during CO2 gasification and air combustion of Inyanda chars. The RPM predictions was validated with the experimental data and exhibited adequate fitting to the specific rate of reaction versus carbon conversion plots of the char samples at the different reaction conditions chosen for this study. The activation energy determined was minimal for air and maximum for CO2 for both coals; and ranged from 127-175 kJ·mol-1 for combustion, 214-228 kJ·mol-1 and 210-240 kJ·mol-1 for steam and CO2 gasification respectively. / MIng (Chemical Engineering), North-West University, Potchefstroom Campus, 2015

An investigation was undertaken to compare the kinetics of combustion and gasification reactions of chars prepared from two South African coals in different reaction atmospheres: air, steam, and carbon dioxide. The two original coals were characterised as vitrinite-rich (Greenside) and inertinite-rich (Inyanda) coals with relatively low ash content (12.5-16.7 wt. %, adb). Chars were prepared from the parent coals under nitrogen atmosphere at 900 °C. Characterisation results show that the volatiles and moisture were almost completely driven off from the parent coals, indicating that the pyrolysis process was efficient. Physicalstructural properties such as porosity and surface area generally increased from the parent coals to the subsequent chars. The heterogeneous char-gas reactions were conducted isothermally in a TGA on ~1 mm size particles. To ensure that the reactions are under chemical reaction kinetic control regime, different temperatures zones were selected for the three different reaction atmospheres. Combustion reactivity experiments were carried out with air in the temperature range of 387 °C to 425 °C; gasification reactivity with pure steam were conducted at higher temperatures (775 °C - 850 °C) and within 825 °C to 900 °C with carbon dioxide. Experimental results show differences in the specific reaction rate with carbon conversion in different reaction atmospheres and char types. Reaction rates in all three reaction atmospheres were strongly dependent on temperature, and follow the Arrhenius type kinetics. All the investigated reactions (combustion with air and gasification with CO2 and steam) were found to be under chemical reaction control regime (Regime I) for both chars. The inertinite-rich coals exhibit longer burn-out time than chars produced from vitrinite-rich coals, as higher specific reaction rate were observed for the vitrinite-rich coals in the three different reaction atmospheres. The determined random pore model (RPM) structural parameters did not show any significant difference during steam gasification of Greenside and Inyanda chars, whereas higher structural parameter values were observed for Greenside chars during air combustion and CO2 gasification (ψ > 2). However a negative ψ value was determined during CO2 gasification and air combustion of Inyanda chars. The RPM predictions was validated with the experimental data and exhibited adequate fitting to the specific rate of reaction versus carbon conversion plots of the char samples at the different reaction conditions chosen for this study. The activation energy determined was minimal for air and maximum for CO2 for both coals; and ranged from 127-175 kJ·mol-1 for combustion, 214-228 kJ·mol-1 and 210-240 kJ·mol-1 for steam and CO2 gasification respectively. / MIng (Chemical Engineering), North-West University, Potchefstroom Campus, 2015

Dans le contexte économique de la plupart des pays en voie de développement, la gazéification sous vapeur d’eau de résidus agricoles lignocellulosiques pourrait être un procédé intéressant, à la fois pour la génération d’énergie dans des régions isolées et pour la production des produits à valeur ajoutée. Étant donné que la disponibilité des résidus agricoles est souvent saisonnière, différents types de biomasse doivent être utilisés pour assurer le fonctionnement des installations de gazéification. A cet égard, ce travail est axé sur la compréhension de l'impact des caractéristiques de la biomasse sur le procédé de gazéification et les propriétés des sous-produits gazeux et solides. Trois biomasses lignocellulosiques à composition macromoléculaire et inorganique différentes ont été sélectionnées pour cette étude : coques de noix de coco (CS), bambou guadua (BG) et coques de palmier à huile (OPS). La cinétique de décomposition thermique des biomasses a été étudiée sur une échelle thermogravimétrique sous atmosphère inerte et sous vapeur d’eau. Malgré les différences dans la structure macromoléculaire des échantillons, la composition inorganique s’est avérée être le paramètre le plus important influençant la réactivité et la cinétique de gazéification. L'impact bénéfique des métaux alcalins et alcalino-terreux a été confirmé, ainsi que l'effet inhibiteur du Si et du P. Plus précisément, le ratio K/(Si+P) est considéré approprié pour décrire et comparer le comportement des biomasses pendant la gazéification sous vapeur d’eau. En conséquence, une nouvelle approche pour la modélisation de la cinétique de gazéification à partir de la composition inorganique de l’échantillon a été proposée. La validité du ratio K/(Si+P) pour classifier et prédire le comportement des biomasses a également été confirmée par des expériences dans un réacteur à lit fluidisé à l’échelle laboratoire. Les échantillons avec un ratio K/(Si+P) au-dessus de 1 ont montré des réactivités de gazéification supérieures à celles des échantillons dont le ratio était inférieur à 1, et donc, une production de gaz et un rendement énergétique plus élevés. De plus, la composition inorganique a non seulement impacté le taux de gazéification des échantillons, mais également les propriétés du sous-produit solide. En particulier, une réactivité de gazéification plus élevée est liée à des chars avec une surface spécifique et un nombre de groupes fonctionnels plus importants. Une température de 850°C et une fraction de vapeur de 30% dans l’agent de réaction ont été identifiées comme les conditions les plus adaptées à la production simultanée de gaz combustible et de char pouvant être valorisé dans des applications agricoles. Le modèle de gazéification sous vapeur d'eau et les résultats expérimentaux présentés dans ce travail peuvent être une référence pour des applications réelles de gazéification travaillant avec différents types de résidus. Par ailleurs, dans le contexte présenté, la gazéification sous vapeur d’eau de déchets lignocellulosiques peut améliorer l’accès à l’énergie des zones rurales isolées, en promouvant simultanément le développement de projets productifs susceptibles de générer de nouveaux revenus pour les communautés locales. / In the context of most developing countries, steam gasification could be a very interesting process for both energy generation in isolated areas and the production of value-added products from lignocellulosic agrowaste. Considering that the availability of agricultural residues is often seasonal, gasification facilities should operate with different feedstocks. In consequence, this work is focused on the understanding of the impact of biomass characteristics on the gasification process and the properties of the gaseous and solid by-products. Three lignocellulosic agrowastes with different macromolecular structure and inorganic composition were selected for this study: Coconut shells (CS), bamboo guadua (BG) and oil palm shells (OPS). The thermal decomposition kinetics of the selected feedstocks was analyzed in a thermogravimetric scale under inert and steam atmosphere. Despite the differences in their macromolecular composition, inorganics showed to be the most important parameter influencing the steam gasification reactivity and kinetics of the samples. The beneficial impact of AAEM was confirmed, as well as the inhibitory effect of Si and P. More specifically, the ratio K/(Si+P) proved to be suitable to describe and compare the steam gasification behavior of lignocellulosic agrowastes. In accordance, a new kinetic modeling approach was proposed to predict the gasification behavior of samples, from the knowledge of their inorganic composition. The validity of the ratio K/(Si+P) to classify and predict the biomass steam gasification behavior was also confirmed from experiments in a lab-scale fluidized bed gasifier. Samples with K/(Si+P) above 1 exhibited higher gasification reactivities compared to samples with ratios below 1, resulting in greater gas yields and higher gas efficiencies. Moreover, inorganics impacted not only the gasification rate of the samples, but also the properties of the gasification solid by-products. In particular, higher gasification reactivities were related to greater char surface areas and contents of oxygenated surface functional groups. A temperature of 850°C and a steam fraction of 30% in the reacting atmosphere proved to be the most suitable gasification conditions for the simultaneous production of fuel gases for energy applications, and a valuable char that could be valorized in soil amendment applications. The gasification model and experimental results presented in this work might be an important reference for real gasification applications working with different kind of residues, when both the gaseous and solid by-products valorization is intended. Moreover, in the presented context, steam gasification of lignocellulosic agrowaste may improve the energy access in rural isolated areas, and simultaneously promote the development of productive projects that could generate new incomes for local communities.

Améliorer la production en hydrogène dans les procédés de conversion des ressources renouvelables telles que la biomasse est un réel challenge dans le contexte de la production d’énergie propre et efficace. En effet, dans le procédé de conversion de la biomasse par vapogazéification, l’hydrogène est produit avec de quantités importantes de CO2, de CH4 et des molécules aromatiques lourdes, toxiques et complexes appelées goudrons. Ce travail s’intéresse à la production d’hydrogène par vaporeformage des goudrons avec capture in-situ de CO2 dans les procédés de vapogazéification de la biomasse. Nous proposons un système catalytique bifonctionnel de type Fe/CaO-Ca12Al14O33 dans lequel le fer est actif pour la production d’H2 tandis que la phase absorbante CaO-Ca12Al14O33 capture le CO2, ces deux processus se font simultanément dans un réacteur à lit fixe. Ce travail a permis de développer un système de type CaOCa12Al14O33/ olivine adapté pour la gazéification de la biomasse « Miscanthus » dans un réacteur à lit fluidisé. / Improve the hydrogen production from the conversion of renewable resources such as biomass is a real challenge in the context of the production of clean and efficient energy. In fact, during the biomass steam gasification, hydrogen is produced with significant amounts of CO2, CH4 and heavy, toxic and complex aromatic molecules called tars. This work focuses on the production of hydrogen by steam reforming of tar with in-situ CO2 capture. We propose a catalytic bi-functional material Fe/CaO-Ca12Al14O33 where iron favors the H2 production and simultaneously the CaO-Ca12Al14O33 capture CO2 in a fixed bed reactor. This work led also to the development of a CaOCa12Al14O33/ olivine system adapted for biomass gasification "Miscanthus" in a fluidized bed reactor.

The present work focuses on the study of biomass gasification process for generating hydrogen rich synthetic gas with oxy-steam as reactants using experiments and modeling studies. Utilization of the syngas as a fuel in general applications like fuel cells, Fischer-Tropsch FT) process and production of various chemicals like DME, etc. are being considered to meet the demand for clean energy. This study comprises of experiments using an open top down draft reactor with oxygen and steam as reactants in the co-current configuration. Apart from the standard gasification performance evaluation; parametric study using equivalence ratio, steam-to-biomass ratio as major variables towards generation of syngas is addressed towards controlling H2/CO ratio. The gasification process is modeled as a packed bed reactor to predict the exit gas composition, propagation rate, bed temperature as a function of input reactants, temperature and mass flux with variation in thermo-physical properties of biomass. These results are compared with the present experiments as well as those in literature. Experiments are conducted using modified open top downdraft configuration reactor with lock hoppers and provision for oxy-steam injection, and the exit gas is connected to the cooling and cleaning system. The fully instrumented system is used to measure bed temperatures, steam and exit gas temperature, pressures at various locations, flow rates of fuel, reactants and product gas along with the gas composition. Preliminary investigations focused on using air as the reactant and towards establishing the packed bed performance by comparing with the experimental results from the literature and extended the study to O2-N2 mixtures. The study focuses on determining the propagation rate of the flame front in the packed bed reactor for various operating conditions. O2 is varied between 20-100% (vol.) in a mixture of O2-N2 to study the effect of O2 fraction on flame propagation rate and biomass conversion. With the increase in O2 fraction, the propagation rates are found to be very high and reaching over 10 mm/s, resulting in incomplete pyrolysis and poor biomass conversion. The flame propagation rate is found to vary with oxygen volume fraction as XO22.5, and stable operation is achieved with O2 fraction below 30%. Towards introducing H2O as a reactant for enhancing the hydrogen content in the syngas and also to reduce the propagation rates at higher ER, wet biomass is used. Stable operating conditions are achieved using wet biomass with moisture-to-biomass (H2O:Biomass) ratio between 0.6 to 1.1 (mass basis) and H2 yield up to 63 g/kg of dry biomass amounting to 33% volume fraction in the syngas. Identifying the limitation on the hydrogen yield and the criticality of achieving high quality gas; oxy-steam mixture is introduced as reactants with dry biomass as fuel. An electric boiler along with a superheater is used to generate superheated steam upto 700 K and pressure in the range of 0.4 MPa. Steam-to-biomass ratio (SBR) and ER is varied with towards generating hydrogen rich syngas with sustained continuous operation of oxy-steam gasification of dry biomass. The results are analysed with the variation of SBR for flame propagation rates, calorific value of product syngas, energy efficiency, H2 yield per kg of biomass and H2/CO ratio. Hydrogen yield of 104 g per kg of dry casuarina wood is achieved amounting to 50.5% volume fraction in dry syngas through oxy-steam gasification process compared to air gasification hydrogen yield of about 40 g per kg of fuel and 20% volume fraction. First and second law analysis for energy and exergy efficiency evaluation has been performed on the experimental results and compared with air gasification. Individual components of the energy input and output are analysed and discussed. H2 yield is found to increase with SBR with the reduction in energy density of syngas and also energy efficiency. Highest energy efficiency of 80.3% has been achieved at SBR of 0.75 (on molar basis) with H2 yield of 66 g/kg of biomass and LHV of 8.9 MJ/Nm3; whereas H2 yield of 104 g/kg of biomass is achieved at SBR of 2.7 with the lower efficiency of 65.6% and LHV of 7.4 MJ/Nm3. The energy density of the syngas achieved in the present study is roughly double compared to the LHV of typical product gas with air gasification. Elemental mass balance technique has been employed to identify carbon boundary at an SBR of 1.5. Controlling parameters for arriving at the desired H2/CO ratio in the product syngas have been identified. Optimum process parameters (ER and SBR) has been identified through experimental studies for sustained continuous oxy-steam gasification process, maximizing H2 yield, controlling the H2/CO ratio, high energy efficiency and high energy density in the product syngas. Increase in ER with SBR is required to compensate the reduction in O2 fraction in oxy-steam mixture and to maintain the desired bed temperature in the combustion zone. In the range of SBR of 0.75 to 2.7, ER requirement increases from 0.18 to 0.3. The sustained continuous operation is possible upto SBR of 1.5, till the carbon boundary is reached. Operating at high SBR is required for high H2 yield but sustained highest H2 yield is obtained as SBR of 1.5. H2/CO ratio in the syngas increases from 1.5 to 4 with the SBR and depending on the requirement of the downstream process (eg., FT synthesis), suitable SBR and ER combination is suggested. To obtain high energy density in syngas and high energy efficiency, operations at lower SBR is recommended. The modeling study is the extension of the work carried by Dasappa (1999) by incorporating wood pyrolysis model into the single particle and volatile combustion for the packed bed of particles. The packed bed reactor model comprises of array of single particles stacked in a vertical bed that deals with the detailed reaction rates along with the porous char spheres and thermo-physical phenomenon governed by the mass, species and energy conservation equations. Towards validating the pyrolysis and single particle conversion process, separate analysis and parametric study addressing the effects of thermo-physical parameters like particle size, density and thermal conductivity under varying conditions have been studied and compared with the available results from literature. It has been found that the devolatilisation time of particle (tc) follows closely the relationship with the particle diameter (d), thermal conductivity (k), density () and temperature (T) as: The complete combustion of a single particle flaming pyrolysis and char combustion has been studied and validated with the experimental results. For the reactor modeling, energy, mass and species conservation equations in the axial flow direction formulate the governing equations coupled to the detailed single particle analysis. Gas phase reactions involving combustion of volatiles and water gas shift reaction are solved in the packed bed. The model results are compared with the experimental results from wood gasification system with respect to the propagation rate, conversion times, exit gas composition and other bed parameters like conversion, peak bed temperatures, etc. The propagation rates compare well with experimental data over a range of oxygen concentration in the O2- N2 mixture, with a peak at 10 mm/s for 100 % O2. In the case of oxy-steam gasification of dry biomass, the results clearly suggest that the char conversion is an important component contributing to the bed movement and hence the overall effective propagation rate is an important parameter for co-current reactors. This is further analyzed using the carbon boundary points based on elemental balance technique. The model predictions for the exit gas composition from the oxy-steam gasification matches well with the experimental results over a wide range of equivalence ratio and steam to biomass ratio. The output gas composition and propagation rates are found to be a direct consequence of input mass flux and O2 fraction in oxy-steam mixture. The present study comprehensively addresses the oxy-steam gasification towards generating hydrogen rich syngas using experimental and model studies. The study also arrives at the parameters for design consideration towards operating an oxy-steam biomass gasification system. The following flow chart provides the overall aspects that are covered in the thesis chapter wise.