In Sweden spent nuclear fuel is planned to be placed 500 m down in the bedrock. The spent nuclear fuel will be contained in copper canisters. The reason behind the selection of copper is its thermodynamic stability against corrosion in the depository. The copper will be exposed to mechanical loading and will be plastically deformed due to creep. The canisters will be sealed by friction stir welding. Since the canisters have to survive intact for many thousands of years, the properties of the welds are critical. Oxygen free P-doped copper (Cu-OFP) is selected for its excellent creep ductility properties and corrosion resistance. In this thesis work creep ductility behavior of friction stir welded copper chosen at different areas of the weld is evaluated by using the test slow strain rate tensile test. Samples are chosen at different weld areas namely weld, cross weld and HAZ. A sum of 21 specimens is tested. These tests are achieved at three various strain rates and each rate are carried out at three different temperatures. The strain rates used for tests are 1e-4, 3e-6 and 1e-7 [1/s]. The samples are strained until rupture, 20% and 5% of the gauge length. Yield strength and tensile strength are usually decreasing with increasing temperature and at higher temperature the material can be easily deformed. Few strange behaviors are also observed for the samples from HAZ areas at strain rate 1e-7[1/s]. The experimental results are justified by using the Knock-Mecking model. The parametersand ω were evaluated by curve fitting method.

The Swedish model for final disposal of nuclear fuel waste is based on copper canisters as a corrosion barrier with an inner pressure holding insert of cast iron. One of the methods to seal the copper canister is to use the Friction Stir Welding (FSW), a method invented by The Welding Institute (TWI). This work has been focused on characterisation of the FSW joints, and modelling of the process, both analytically and numerically. The first simulations were based on Rosenthal’s analytical medium plate model. The model is simple to use, but has limitations. Finite element models were developed, initially with a two-dimensional geometry. Due to the requirements of describing both the heat flow and the tool movement, three-dimensional models were developed. These models take into account heat transfer, material flow, and continuum mechanics. The geometries of the models are based on the simulation experiments carried out at TWI and at Swedish Nuclear Fuel Waste and Management Co (SKB). Temperature distribution, material flow and their effects on the thermal expansion were predicted for a full-scale canister and lid. The steady state solutions have been compared with temperature measurements, showing good agreement. Microstructure and hardness profiles have been investigated by optical microscope, Scanning Electron Microscope (SEM), Electron Back Scatter Diffraction (EBSD) and Rockwell hardness measurements. EBSD visualisation has been used to determine the grain size distribution and the appearance of twins and misorientation within grains. The orientation maps show a fine uniform equiaxed grain structure. The root of the weld exhibits the smallest grains and many annealing twins. This may be due to deformation after recrystallisation. The appearance of the nugget and the grain size depends on the position of the weld. A large difference can be seen both in hardness and grain size between the start of the weld and when the steady state is reached. / QC 20101207

Combinations of different materials are increasingly used in the modern engineering structures. The driving forces of this trend are rising fuel costs, global warming, customer demands and strict emission standards. Engineers and industries are forced to improve fuel economy and cut emissions by introducing newly design engines and lightweighting of structural components. The use of lightweight materials in the structures has proved successful to solve these problems in many industries especially automobile and aerospace. However, industry still lacks knowledge how to manufacture components from polymeric materials in combination with metals where significant differences exist in properties. This thesis aims to demonstrate and generate the methodology and guidelines for hybrid joining of aluminium alloys to thermoplastics using friction stir welding. The developed technique was identified, optimized and evaluated from experimental data, metallography and mechanical characterization. The success of the technique is assessed by benchmarking with recent literatures. In this work, lap joints between aluminium alloys (AA5754, AA6111) and thermoplastics (PP, PPS) were produced by the friction stir welding technique. The specimens were joined with the friction stir welding tools under as-received conditions. Metallic chips were generated and merged with the molten thermoplastic to form a joint under the influence of the rotating and translating tool. The effects of process parameters such as rotational speed, translational speed and distance to backing were analyzed and discussed. The investigation found joint strength was dominated by mechanical interlocking between the stir zone and the aluminium sheet. The results also show that the joint strength is of the same order of magnitude as for other alternative joining techniques in the literature. / <p>QC 20150908</p>

The present study investigates the fracture toughness of FSW X-80 HSLA steel welds. Weld cooling rate and peak temperature were varied among welds; indirectly manipulated through FSW travel speed, rpm, and weld preheat. Fracture toughness was tested according to ASTM 1820 standard along the weld centerline using surface-notched SEB specimen cooled to -40 °C. This study resulted in a reliable, repeatable process for generating friction stir welds with CTOD’s consistently above that of the original base metal. CTOD and microstructure of friction stir welds can be selected by controlling weld cooling rate and peak temperature. Material properties and microstructure similar to the original base metal can be recreated throughout the weld stir zone. CTOD of FSW X80 has a strong inverse linear correlation with post-weld cooling rate.

Hybrid structures including aluminum-thermoplastic and aluminum-reinforced thermoplastic composite are increasingly important in the near future innovations due to its lightweight and high strength-to-weight ratio. A critical point for metal-polymer application is that sound joining of these materials is difficult to achieve owing to a large difference in surface energy and dissimilar structure between metal and polymer. In practice, two major joining methods for hybrid structures are mechanical joining and adhesive bonding. However, there are some drawbacks of these conventional methods such as stress concentration, long curing time and low reliability joints. A new novel metal-polymer hybrid joining is required to overcome these issues as well as manufacturing and cost perspectives. To this end, this work aims to develop a general methodology to apply friction stir welding techniques to join a wide range of thermoplastics with and without fibers to aluminum alloy sheets. The present work proposed an experimental study to attain insight knowledge on the influences of welding parameters on the quality of hybrid joints in term of the maximum tensile shear strength. This includes the role of tool geometries, welding methodology as well as material weldability in the investigation. The results showed that friction stir welding is a promising technique for joining of thermoplastic to aluminum. Microstructural observation showed that a good mixing between aluminum and thermoplastic as well as defect-free weldments were obtained. Tool geometries and welding speed are two factors that significantly contribute to the quality of friction stir welded hybrid joints. The results also demonstrated that weld fracture modes are associated with material mixing as well as interfacial bonding between aluminum and thermoplastic. An evaluation of the joint strength was benchmarked with the relevant literatures on hybrid joining. The results of proposed technique showed that the maximum tensile shear strength of friction stir welded joints were the same order of magnitude as the joints welded by laser welding.

Additive friction stir deposition is characterized by rotating a consumable feedstock rod that induces severe plastic deformation to deposit material additively without raising the material past its melting point. In this way, additive friction stir deposition differs from traditional additive manufacturing, and new developments in this technology require further investigation of build parameters, tooling, and resultant builds to better understand this printing process and its applications. This thesis evaluated the effect of rotational speed on aluminum 6061 builds using mechanical testing and microstructural investigations. Three different build conditions were evaluated at 180 RPM, 240 RPM, and 300 RPM. Mechanical testing methods were used to determine hardness values, ultimate tensile strength, yield strength, elastic modulus, and density. Imaging techniques including optical microscopy, electron backscatter diffraction, energy dispersive x-ray spectroscopy, and x-ray computed tomography were used to evaluate microstructure, grain size, chemical composition, and porosity.

A two-dimensional axisymmetric thermo-mechanical model of the Refill Friction Stir Spot Welding (RFSSW) process was developed and validated with experimental data. Welding temperatures, tool forces, and material flow including defect formation, were accurately predicted by the model. Qualified repair techniques are critical for successful implementation of a welding process for use on large weldments with a significant number of spot joints, and this work demonstrates a repair technique for RFSSW that is validated both experimentally and numerically. Repaired properties are shown to exceed 90% of the original mechanical properties of the RFSSW process. RFSSW has different process parameters for every combination of material alloy, material thickness, weld duration, and machine force limits. Numerical modeling develops the process parameters for any RFSSW iteration in a fraction of the time with the same amount of accuracy. The model can effectively simulate how to determine the optimal weld duration given any experimental parameters.

This work establishes the relationships between several key Friction Stir Welding process parameters and the resulting microstructural and flexural properties of the welded joint. A series of four single parameter experiments were run. The parameters investigated were pin diameter, feedrate, shoe temperature, and pressure time. Butt welds were made in 6 mm thick stress-relieved extruded polypropylene sheet. Three-point bend tests were used to determine the ultimate flexural strength and coincident strain. The maximum bend angle before failure was used to label the welds as "good or bad." An optical microscope capable of cross polarization was used to examine and photograph the weld microstructure. Welds were evaluated according to 1) DVS bend angle, 2) flexural properties, and 3) weld microstructure. All welds made surpassed the DVS requirements for classification as a "good weld" established for hot-gas, extrusion, and laser welding processes. Most welds met the bend angle requirement for hot-plate welds. Welds created for this work maintained 80-92% of base material flexural strength. In the majority of the welds, the strength was between 85 and 90% of base material. The FSW joints showed a flexural strength of 10500 psi, compared to a base material strength of 12400 psi. Four microstructural zones were found to exist in the FSW joints. These were: 1)advancing interface, 2) retreating interface, 3) bottom disturbance, and 4) central zone. Several common microstructure types and defects were found to exist in the welds. These were: 1) spherulites, 2) voids, 3) root defects, 4) flow lines, and 5) onion skin. A distinct correlation was observed between weld microstructure and flexural properties. Those welds whose microstructure most nearly resembled the base material demonstrated the best flexural properties. This can be accomplished by operating with a low feedrate, a high shoe temperature, and a large pin.

The purpose of this research was to use the Transvalor S.A. product, Forge3, to develop a finite element simulation of the friction stir welding process that improves the predictability of temperature evolution and material flow within the plunge portion of the process. Previous modeling created more heating within the billet than experimental results, probably due to the simplification of the simulation with adiabatic boundary conditions. More realistic tooling temperatures were included in this model as these affect heat evolution which is a determining factor in microcrystalline growth. These results were validated by experimental efforts using a billet and tooling instrumented with thermocouples used to evaluate the temperatures at specific locations over time. Simulation results were compared with previous experiments to validate the predicted material flow.

The longitudinal forces generated from the Friction Stir Welding process are substantial. An understanding of these forces is critical to proper tool design. This study describes a technique to measure the longitudinal force distribution on a friction stir weld pin tool. Total longitudinal forces were recorded on a dynamometer while welding 6061 aluminum with non-threaded pins that varied in length and diameter. A model was developed that characterizes pin force as a function of pin length and diameter. Results suggest that force generally increases with pin length, while forces remain relatively constant with pin diameter. Unexpected force variation was found at large pin lengths, which yielded several possible models of the force distribution. All of the modeled force distributions proved to be non-uniform and increase linearly with pin length, which produces a pin force that increases with the square of the pin length.