1 |
Design, Analysis and Applications of Hybrid CORDIC Processor ArchitecturesLee, Cheng-Han 31 August 2010 (has links)
In this thesis, we propose different CORDIC architectures which solve the problems of long-latency in traditional pipeline CORDIC and the large-area cost in table-based CORDIC. The original table-based CORDIC can be divided into two stages, coarse stage and fine stage. We also propose the three-stage architectures, composed of traditional pipeline CORDIC, Rom/Multiplier architecture and linear approximation. Detailed analysis and estimation in area and latency of these different two-stage and three-stage architectures with different bit accuracy are given in order to determine the best architecture design for a particular precision. Finally, we choose one of the architectures to implement, compare the results, and show its applications.
|
2 |
Table-Based Design of Arithmetic Function Units for Angle Rotation and Rectangular-to-Polar-Coordinate ConversionCheng, Yen-Chun 01 September 2009 (has links)
In this thesis, an efficiency method for reducing the rotation ROM size in table-based architecture is proposed. The original rotation can be divided into two stages, coarse stage and fine stage. Our approach modifies the previous two-stage rotation method and proposes a multi-stage architecture and discuses three-stage phase calculation. The effect of table reduction is more apparently for higher accuracy requirement in the three-stage architecture. The total area of the previous two-stage architecture is larger than the proposed table-reduced three-stage architecture because the table size takes a significant ratio of the total area especially when the required bit accuracy is large. In the proposed three-stage design, there are two different types of architectures, depending on the rotation angles in the first and second rotation stages. Comparison of different types of architecture with the previous method shows that our designs indeed reduce the table size and the total area significantly.
|
3 |
Median and Mode Approximation for Skewed Unimodal Continuous Distributions using Taylor Series ExpansionDula, Mark, Mogusu, Eunice, Strasser, Sheryl, Liu, Ying, Zheng, Shimin 06 April 2016 (has links)
Background: Measures of central tendency are one of the foundational concepts of statistics, with the most commonly used measures being mean, median, and mode. While these are all very simple to calculate when data conform to a unimodal symmetric distribution, either discrete or continuous, measures of central tendency are more challenging to calculate for data distributed asymmetrically. There is a gap in the current statistical literature on computing median and mode for most skewed unimodal continuous distributions. For example, for a standardized normal distribution, mean, median, and mode are all equal to 0. The mean, median, and mode are all equal to each other. For a more general normal distribution, the mode and median are still equal to the mean. Unfortunately, the mean is highly affected by extreme values. If the distribution is skewed either positively or negatively, the mean is pulled in the direction of the skew; however, the median and mode are more robust statistics and are not pulled as far as the mean. The traditional response is to provide an estimate of the median and mode as current methodological approaches are limited in determining their exact value once the mean is pulled away. Methods: The purpose of this study is to test a new statistical method, utilizing the first order and second order partial derivatives in Taylor series expansion, for approximating the median and mode of skewed unimodal continuous distributions. Specifically, to compute the approximated mode, the first order derivatives of the sum of the first three terms in the Taylor series expansion is set to zero and then the equation is solved to find the unknown. To compute the approximated median, the integration from negative infinity to the median is set to be one half and then the equation is solved for the median. Finally, to evaluate the accuracy of our derived formulae for computing the mode and median of the skewed unimodal continuous distributions, simulation study will be conducted with respect to skew normal distributions, skew t-distributions, skew exponential distributions, and others, with various parameters. Conclusions: The potential of this study may have a great impact on the advancement of current central tendency measurement, the gold standard used in public health and social science research. The study may answer an important question concerning the precision of median and mode estimates for skewed unimodal continuous distributions of data. If this method proves to be an accurate approximation of the median and mode, then it should become the method of choice when measures of central tendency are required.
|
4 |
Efficient, Accurate, and Non-Gaussian Error Propagation Through Nonlinear, Closed-Form, Analytical System ModelsAnderson, Travis V. 29 July 2011 (has links) (PDF)
Uncertainty analysis is an important part of system design. The formula for error propagation through a system model that is most-often cited in literature is based on a first-order Taylor series. This formula makes several important assumptions and has several important limitations that are often ignored. This thesis explores these assumptions and addresses two of the major limitations. First, the results obtained from propagating error through nonlinear systems can be wrong by one or more orders of magnitude, due to the linearization inherent in a first-order Taylor series. This thesis presents a method for overcoming that inaccuracy that is capable of achieving fourth-order accuracy without significant additional computational cost. Second, system designers using a Taylor series to propagate error typically only propagate a mean and variance and ignore all higher-order statistics. Consequently, a Gaussian output distribution must be assumed, which often does not reflect reality. This thesis presents a proof that nonlinear systems do not produce Gaussian output distributions, even when inputs are Gaussian. A second-order Taylor series is then used to propagate both skewness and kurtosis through a system model. This allows the system designer to obtain a fully-described non-Gaussian output distribution. The benefits of having a fully-described output distribution are demonstrated using the examples of both a flat rolling metalworking process and the propeller component of a solar-powered unmanned aerial vehicle.
|
5 |
Non-Smooth SDEs and Hyperbolic Lattice SPDEs Expansions via the Quadratic Covariation Differentiation Theory and ApplicationsAshu, Tom A. 20 July 2017 (has links)
No description available.
|
6 |
Modèles réduits pour des analyses paramètriques du flambement de structures : application à la fabrication additive / Reduced order models for multiparametric analyses of buckling problems : application to additive manufacturingDoan, Van Tu 06 July 2018 (has links)
Le développement de la fabrication additive permet d'élaborer des pièces de forme extrêmement complexes, en particulier des structures alvéolaires ou "lattices", où l'allégement est recherché. Toutefois, cette technologie, en très forte croissance dans de nombreux secteurs d'activités, n'est pas encore totalement mature, ce qui ne facilite pas les corrélations entre les mesures expérimentales et les simulations déterministes. Afin de prendre en compte les variations de comportement, les approches multiparamétriques sont, de nos jours, des solutions pour tendre vers des conceptions fiables et robustes. L'objectif de cette thèse est d'intégrer des incertitudes matérielles et géométriques, quantifiées expérimentalement, dans des analyses de flambement. Pour y parvenir, nous avons, dans un premier temps, évalué différentes méthodes de substitution, basées sur des régressions et corrélations, et différentes réductions de modèles afin de réduire les temps de calcul prohibitifs. Les projections utilisent des modes issus soit de la décomposition orthogonale aux valeurs propres, soit de développements homotopiques ou encore des développements de Taylor. Dans un second temps, le modèle mathématique, ainsi créé, est exploité dans des analyses ensemblistes et probabilistes pour estimer les évolutions de la charge critique de flambement de structures lattices. / The development of additive manufacturing allows structures with highly complex shapes to be produced. Complex lattice shapes are particularly interesting in the context of lightweight structures. However, although the use of this technology is growing in numerous engineering domains, this one is not enough matured and the correlations between the experimental data and deterministic simulations are not obvious. To take into account observed variations of behavior, multiparametric approaches are nowadays efficient solutions to tend to robust and reliable designs. The aim of this thesis is to integrate material and geometric uncertainty, experimentally quantified, in buckling analyses. To achieve this objective, different surrogate models, based on regression and correlation techniques as well as different reduced order models have been first evaluated to reduce the prohibitive computational time. The selected projections rely on modes calculated either from Proper Orthogonal Decomposition, from homotopy developments or from Taylor series expansion. Second, the proposed mathematical model is integrated in fuzzy and probabilistic analyses to estimate the evolution of the critical buckling load for lattice structures.
|
Page generated in 0.1286 seconds